基于PIV技术不同形式防波堤周围涡旋场特性研究(英文)

深水防波堤周围流场存在复杂的紊动变化,防波堤较容易发生失效破坏。本文利用PIV技术,基于模型实验,对规则波作用下防波堤周围的速度流场及其涡流特性进行了实验研究,获得了规则波流场的瞬时速度分布。通过对不同型式防波堤在不同的水力条件下的波浪流场实验数据的分析,定量地研究了防波堤堤身水域的涡旋流场的水力特性。     

半圆型防波堤的水力特性研究

采用不规则波浪试验,研究了半圆型防波堤的水力特性及堤上波力随各主要影响因素的变化规律。指出必须分别按出水堤或淹没堤计算堤上的波力,前者可用改进的合田公式;对于淹没堤,文中建议了计算波力的方法。     

堆石防波堤不规则波浪反射系数试验研究

结合物理模型试验,分析斜坡坡度、波陡、相对水深、护面类型和破波参数等因素对堆石防波堤不规则波浪反射系数的影响规律。将常用的Van der Meer公式,Seelig公式,Postma公式和Davison公式计算值和实测值进行比较,并结合试验数据,基于有效波高和平均周期定义的Iribarren数,得出堆石防波堤不规则波浪反射系数经验公式。结果表明,该公式能较好地计算不规则波作用下块石和扭王块体护面堆石防波堤波浪反射系数。     

立管-水平板结构消浪特性试验研究

在现有的矩形方箱和透空结构的基础上,提出一种由立管和水平板组合而成的消浪结构。利用波浪水槽物理模型试验,测试该结构在单向规则波作用下的消浪性能。分别探讨了其单排布置和双排布置时的透射系数随结构宽度、相对吃水深 度、相对间距等因素的变化规律。结果表明：单排布置时,透射系数随结构宽度的增大而减小,总体上随吃水深度的增大而减小;双排布置时,透射系数相对总宽度相同的单体结构减少 10 %,透射系数随吃水深度的增大而减小,前后间距对透射系数的影响不明显。对试验结果数据进行曲线拟合,得到了透射系数关于各影响因素的函数表达式。     

弧形防波堤波浪力试验研究

在圆筒形防波堤和V形防波堤的基础上,结合离岸堤后形成V形和半圆形连续出现的韵律海岸的地貌平面形态特点,提出一种前墙为连续的半圆筒形防波堤形式。通过在波浪水槽内进行规则波物理模型试验,探究这一新型防波堤的波压力分布规律及波高、周期、水深等因素对波压力的影响。将试验结果与海港水文公式和合田良实公式计算的理论值对比分析,给出了以合田良实公式的折减系数来拟合新型弧形防波堤波浪总水平力的计算公式。结果表明:新型弧形防波堤上的波压力随波高、周期的增大而增大,其水平波浪总力比同等尺度直墙少10%左右。     

波浪作用下曲面防波堤水力特性及波能损耗研究

执行了一系列规则波与曲面防波堤相互作用实验。采用π定理确定了两种曲面防波堤(半圆堤和圆弧堤)反射透射水力特性的三个主要影响因素,包括入射波陡、相对水深和堤顶相对超高。基于实验数据对比分析了两种曲面防波堤的反射和透射特性,从能量守恒角度计算了波浪与曲面防波堤相互作用过程中的能量损耗率,并利用数值模拟探讨了波浪越堤过程中两种曲面防波堤波能损耗差异的机理,表明圆弧堤背浪面更强的尾涡区使得其局部能耗总体上高于半圆堤。     

畸形波作用下双层水平板防波堤压力分布特性研究

基于物理模型试验,考虑畸形波参数、相对板宽、相对波高等影响因素,就畸形波对平顶双层水平板防波堤作用进行研究。首先对畸形波作用下双层水平板的波浪力分布特征进行了讨论,然后就最大波动压强、结构最大总垂向力与不规则波作用进行了对比分析。结果表明,畸形波作用下,双层水平板最大波动压力出现在前端迎浪区域附近,向尾端逐渐递减。双层水平板4个受力面的压力分布不同且有相位差,4个受力面的最大波动压力时间差约在0.1T_p~0.4T_p范围内变化。与不规则波作用比较,畸形波作用没有显著改变波压包络分布特征,但增大了波压包络强度值。试验范围内,就最大总力而言,两者最大总浮托力比值在1.06~2.45间变化;向下的最大总垂向力比值在1.22~2.07之间变化;就波动压力而言,其增大的幅度与畸形波参数α₁相关性最强,随α₁的增大而增大,在α₁=2.04~3.1试验范围内,畸形波作用时的最大压强比不规则波作用时可约增大20%~80%。就最大波吸力而言,两者的比值与畸形波参数α₄相关性最强,随α₄的增大而减小。在α₄=0.62~0.75试验范围内,最大波吸力强度的比值在1.61~0.87范围内变化。当α₄≤0.72时,畸形波作用时的最大波吸力大于不规则波作用时的最大波吸力;当α₄ > 0.72时则刚好相反。     

近破波作用下沉箱式防波堤运动特性的模型实验研究

对近破波作用下沉箱式防波堤的运动特性进行了模型实验研究。实验中测量了沉箱模型与基床的摩擦系数、基床刚度和阻尼系数;不同水位情况下作用于沉箱模型上的近破波波压力时程;近破波作用下沉箱模型的位移和转角响应时程等,并与数学模型计算结果进行了比较分析。实验结果表明,若沉箱的滑移力大于沉箱与基床间的摩擦力,在连续波浪作用下,沉箱将连续出现间歇式滑移运动,数学模型可较好地模拟这一运动过程。     

淹没矩形防波堤透反射系数特性研究

采用解析方法研究了斜向入射波作用下淹没矩形防波堤的透反射系数特性.首先利用特征函数展开法导出了绕射势函数的分析解和透反射系数的计算公式,然后利用边界元方法验证了解析解,在此基础上利用解析解分析了若干工况下的防波堤透反射特性.计算结果表明,淹没矩形防波堤截面的宽度、高度和相对位置以及入射角的改变都不同程度影响反射系数和透射系数.在中等深度条件下,对于一定频率的波浪,位置和尺寸适当的淹没矩形堤可以反射大部分斜向入射波.研究结果对设计淹没的矩形防波堤具有重要的参考价值.     

直立式防波堤口门区海啸局部冲刷规律实验研究

海啸作为世界上最严重的自然灾害之一,其巨大的破坏力使得近海建筑物遭受了严重的损害。基于波浪水槽实验,开展海啸波作用下不同口门距离的防波堤局部冲刷机理实验研究。实验结果表明,在海啸波越顶水流产生的水跌以及海啸波通过防波堤口门时产生的扰流共同作用下,口门中心线处产生明显的局部冲刷坑,随着口门距离的增加,防波堤局部冲刷先加剧后减弱。建立防波堤局部最大冲刷深度与海啸波波高、防波堤宽度及出水高度、口门间距的关系式,揭示了最大局部冲刷深度与海啸波波高、防波堤尺寸、口门距离的内在关系。     

Using RANS to simulate vortex generation and dissipation around impermeable submerged double breakwaters

In this paper, a Reynolds Averaged Navier–Stokes (RANS) model was developed to simulate the vortex generation and dissipation caused by progressive waves passing over impermeable submerged double breakwaters. The dynamics of the turbulence are described by introducing a k–ɛ model with Boussinesq closure. The Height Function (HF) is implemented to define the free-surface configuration. The governing equations are discretized by means of a finite volume method based on a staggered grid system with variable width and height. The feasibility of the numerical model was verified through a series of comparisons of numerical results with the existing analytical solutions and the experimental data. The good agreements demonstrate the satisfactory performance of the developed numerical model. The flow separation mechanism both near the upstream and the downstream edges of the obstacles demonstrates the physical and expected nature of development of the flow. The present model provides an accurate and efficient tool for the simulation of flow field and wave transformation near coastal structures without breaking.     

Random wave-induced onshore scour characteristics around submerged breakwaters using a stochastic method

This paper provides a stochastic method by which the two-dimensional onshore scour characteristics along the base of submerged breakwaters exposed to normally incident random waves on both sloping and horizontal sandy seabed can be derived. Here the formulas for the regular wave-induced scour characteristics provided by Young and Testik (2009) are used. These formulas are combined with describing the waves as a stationary Gaussian narrow-band random process to derive the random wave-induced onshore scour characteristics; the maximum scour depth, the scour length, and the distance of the maximum scour depth location from the onshore breakwater face. An example of calculation is also provided.     

Modelling of waves and currents around submerged breakwaters

Recent experimental data collected during the DELOS project are used to validate two approaches for simulating waves and currents in the vicinity of submerged breakwaters.The first approach is a phase-averaged method in which a wave model is used to simulate wave transformation and calculate radiation stresses, while a flow model (2-dimensional depth averaged or quasi-3D) is used to calculate the resulting wave driven currents. The second approach is a phase resolving method in which a high order 2DH-Boussinesq-type model is used to calculate the waves and flow.The models predict wave heights that are comparable to measurements if the wave breaking sub-model is properly tuned for dissipation over the submerged breakwater. It is shown that the simulated flow pattern using both approaches is qualitatively similar to that observed in the experiments. Furthermore, the phase-resolving model shows good agreement between measured and simulated instantaneous surface elevations in wave flume tests.     

透空式防波堤周围的非线性波浪传播的数值模拟

对非线形波浪在透空式防波堤周围的波浪变形进行了数值模拟,在Boussinesq波浪方程中加入与透空建筑物有关的新的耗散项,从而界定了透空建筑物引起的部分反射和透射,波浪折射衍射的传播过程通过控制方程求解。波浪控制方程通过有限差分方法求解。模型应用于模拟波浪经过具有部分反射的群桩式透空结构,结果表明透空式防波堤可以有效地衰减波浪,是重力式结构的一种替代形式。     

Alternative placement technique for antifer blocks used on breakwaters

In this study, a placement technique named as “alternative placement technique” was developed for antifer blocks and the results of its application to a breakwater model were presented. This placement technique was compared with the existing techniques such as the “regular placement technique”, the “irregular placement technique” and the “sloped wall placement technique” by experiments. The comparison was carried out considering armor layer stability, prototype placement, clarity of the placement technique’s definition, armor layer cost, and wave runup. As a result of this investigation the “alternative placement technique” was found to be superior to the other existing placement techniques.     

The role of submerged berms on the momentary liquefaction around conventional rubble mound breakwaters

Berms deployed at the toe of conventional rubble mound breakwaters can be very effective in improving the stability of the armor layer. Indeed, their design is commonly tackled by paying attention to armor elements dimensioning. Past research studies showed how submerged berms can increase the stability of the armor layer if compared to straight sloped conventional breakwaters without a berm. To fill the gap of knowledge related to the interaction between breakwaters with submerged berm, waves and soil, this research aims to evaluate how submerged berms configuration influences the seabed soil response and momentary liquefaction occurrences around and beneath breakwaters foundation, under dynamic wave loading. The effects of submerged berms on the incident waves transformation have been evaluated by means of a phase resolving numerical model for simulating non-hydrostatic, free-surface, rotational flows. The soil response to wave-induced seabed pressures has been evaluated by using an ad-hoc anisotropic poro-elastic soil solver. Once the evaluation of the seabed consolidation state due to the presence of the breakwater has been performed, the dynamic interaction among water waves, soil and structure has been analyzed by using a one-way coupling boundary condition. A parametric study has been carried out by varying the berm configuration (i.e. its height and its length), keeping constant the offshore regular wave condition, the berm and armor layer porosity values, the water depth and the elastic properties of the soil. Results indicate that the presence of submerged berms tends to mitigate the liquefaction probability if compared to straight sloped conventional breakwater without a berm. In addition, it appears that the momentary liquefaction phenomena are more influenced by changing the berm length rather than the berm height.     

Modelling the effect of wave overtopping on nearshore hydrodynamics and morphodynamics around shore-parallel breakwaters

Wave overtopping nearshore coastal structures, such as shore-parallel breakwaters, can significantly alter the current circulation and sediment transport patterns around the structures, which in turn affects the formation of tombolos and salients in the nearshore area. This paper describes the implementation of a wave overtopping module into an existing depth-averaged coastal morphological mode: COAST2D and model applications to investigate the effect of wave overtopping on the hydrodynamics and morphodynamics around a group of shore-parallel breakwaters. The hydrodynamic aspects of the model were validated against a series of laboratory conditions. The model was then applied to a study site at Sea Palling, Norfolk, UK, where 9 shore-parallel segmented breakwaters including 4 surface-piercing and 5 low-crested breakwaters are present, for the storm conditions in Nov 2006. The model results were compared with laboratory data and field measurements, showing a good agreement on both hydrodynamics and morphological changes. Further analysis of wave overtopping effect on the nearshore hydrodynamics and morphodynamics reveals that wave overtopping has significant impacts on the nearshore circulation, sediment transport and the resulting morphological changes within such a complex breakwater scheme under the storm and macro-tide conditions. The results indicate the importance of including the wave overtopping in modelling nearshore morphodynamics with the presence of coastal structures.     

Simulation of flows around cylinders by a Lagrangian vortex scheme

A method is presented for calculating flows around cylinders of arbitrary shape, which may be in an array. Vorticity is discretised and is moved in a Lagrangian time-stepping procedure by the vortex-in-cell method. The zero-velocity surface condition is maintained at each time step by representing the surface by a vortex sheet through a boundary integral calculation. Vorticity diffusion is simulated through random walks. Results are presented for an isolated circular cylinder in steady and oscillatory incident flows.