热-水-力耦合作用下非饱和土变形特性的弹塑性模拟

在已有的非饱和土水-力耦合模型基础上,耦合考虑温度影响,建立了一个热-水-力耦合作用下非饱和土弹塑性本构模型。该模型以土骨架平均应力、修正吸力和温度为应力状态变量,以土骨架应变、饱和度和熵为应变状态变量。通过引入与温度相关的屈服面(LY、TY)以及相应的硬化规律来考虑温度对土体变形的影响。利用建立的模型,对文献中不同吸力和温度条件下的等向压缩和三轴排水剪切试验进行预测,预测结果表明,该模型能够较好地定量描述热-水-力耦合作用下非饱和土的变形特性。     

干湿路径影响粉土小应变剪切模量的试验研究

天然土尤其是地表浅层土常处于非饱和状态,其小应变剪切模量是预测地基变形及土工结构物动力反应的一个重要参数。通过对非饱和压实粉土三轴样进行弯曲元试验,研究了吸力和干湿路径对其小应变剪切模量的影响。试验结果表明,非饱和压实粉土样的小应变剪切模量各向异性忽略不计;小应变剪切模量G0(vh)、G0(hh)和G0(hv)均随吸力增大而非线性增大;同一吸力下不同干湿路径上的土样,饱和度不同,其小应变剪切模量随饱和度升高而减小,主要原因是土的平均骨架应力和土中毛细水的作用。根据试验结果对非饱和土小应变剪切模量的半经验公式进行了改进,同时考虑了吸力与饱和度的作用。     

考虑毛细滞回效应的非饱和多孔介质渗流与变形耦合本构模型

在Wheeler本构模型框架的基础上,提出了一个水力与力学耦合的本构模型。该模型中的土-水特征曲线采用毛细滞回内变量模型,能够更好地描述水力历史变化下毛细滞回现象对非饱和多孔介质变形的影响,同时也可描述非饱和多孔介质变形对渗流的影响。非饱和土的强度不仅与吸力有关,而且受到饱和度的影响。相同的吸力下,土样经过吸湿和脱湿路径的饱和度不同,因此,非饱和土的强度也不同。此模型以体积含水率的塑性变化和体变的塑性变化为硬化参数,不仅能描述基质吸力对非饱和土的强化作用,而且考虑了饱和度对强度及变形的影响。试验结果与模型预测基本吻合,证明该模型能够模拟非饱和土的主要特性。为了简化,此模型是在各向同性荷载下推得的,有待于推广到一般的应力状态     

考虑基质吸力变化时非饱和土的一维本构模型

当地下水位上升或地面遇水浸润时,土的饱和度将因毛细作用而变化,以此使土体产生变形。其中由于含水量增加而使土的重度增大,从而引起压缩变形;同时含水量的增加而使基质吸力下降,从而引起土的回弹变形,因此最终变形取决于上述两种变形趋势的综合效应。根据广义Hook定律、Fredlund的双应力状态变量及Brooks和Corey关于基质吸力与饱和度之间的经验关系,建立了K0状态下非饱和土的一维本构模型。将这一模型与分层总和法相结合,可以计算基质吸力变化时土的竖向变形。通过研究发现,非饱和土的地面变形不仅取决于土的性质与土层的厚度,而且依赖于土中吸力变化前后的分布及应力状态等因素。所建议的一维本构模型可以用于非饱和土地基上基础的沉降估算。     

剪切对非饱和土土-水特征曲线影响的探讨

用净平均应力和吸力等于常数、偏应力增大的三轴排水剪切试验，探讨了剪切对非饱和土水量变化的影响。试验结果表明，土-水特征曲线依赖于偏应力，改进了非饱和土中水量变化的本构关系，建立了含水量．吸力．净平均应力．偏应力形式的土．水特征曲线。     

基于SFG模型的统一屈服面本构模型与试验研究

将SFG模型中的加载湿陷屈服面(LC屈服面)与BBM模型中提出的吸力增加屈服面(SI屈服面)统一成为单独光滑的屈服面,基于弹塑性理论框架,推导出相应的弹塑性本构模型。通过非饱和固结直剪试验对江西红土的模型计算参数的应力-应变曲线与试验结果进行对比。结果表明:模型对多种应力路径下非饱和三轴试验的计算结果与相应试验的测定结果较为吻合,验证了模型能较好地模拟非饱和土在多种应力路径下的体应变行为。统一屈服面简化了加载湿陷屈服面与吸力增加屈服面之间的耦合分析,解决了因双屈服面的不连续而造成计算不便问题,拓宽了SFG模型的适用性。     

非饱和土的水力和力学特性及其弹塑性描述

简单回顾了非饱和土本构模型研究的发展历程,总结了近几年非饱和土弹塑性本构模型最新研究成果,重点介绍了能统一模拟非饱和土水力性状和力学性状耦合的弹塑性本构模型。通过对建立模型过程中的几个核心问题讨论,较详细地说明该类模型的结构、性能以及相关问题。非饱和土水力性状的滞回性用假定存在饱和度弹性区间的弹塑性过程来模拟;该类耦合模型不仅考虑了吸力对非饱和土水力性状和力学性状的影响,还考虑了饱和度对应力-应变关系和强度的影响以及土体变形对土-水特征曲线的影响。用同一套模型参数,耦合模型可统一预测在吸力控制或含水率控制下沿各种应力路径下非饱和土的水力-力学特性,并简单介绍了膨胀性非饱和土的弹塑性本构模型以及耦合模型在有限元数值计算中的应用。     

非饱和土弹塑性模型参数的试验确定及有限元法

简要介绍广泛应用的非饱和土Alonso模型的原理与发展,并通过3组共7个试样的非饱和土三轴试验,得到模型的11个参数。在饱和土Cam本构关系的基础上,推导出一个基于非饱和土Alonso模型的应力-应变增量方程的计算公式,该方程与饱和土的本构方程形式相同。编制了能够考虑净应力和吸力二者对土体硬化规律影响的有限元程序,从而为非饱和土弹塑性计算提供一条途径,便于进一步应用于实际工程。     

饱和度对非饱和土力学性质的影响

现在被广泛公认的由Fredlund提出的非饱和土力学的双参数理论,即净应力和吸力为非饱和土的应力状态量,不能直接考虑饱和度或含水率对非饱和土的应力-应变关系和强度的影响。在非饱和土三轴试验结果表明,即使在净应力和吸力路径相同的条件下,具有不同饱和度试样的应力-应变关系和强度也是不同的。其他条件相同时,试样饱和度越高,其应力比-应变关系曲线越高,强度越大。最新的水力-力学特性耦合的弹塑性本构模型可以定量地表示上述非饱和土的性质     

非饱和重塑黄土的土水特性及压缩屈服与湿陷性的研究

利用改造的非饱和土固结仪对Q_3重塑黄土分别进行了无应力作用的分级增湿试验和控制基质吸力的压缩试验,测试得到了土–水特征曲线和压缩应力–应变曲线,研究了饱和度与基质吸力和含水率与基质吸力之间关系、压缩屈服应力随基质吸力的变化规律和湿陷系数随基质吸力的变化规律。研究结果表明,非饱和重塑黄土的吸力较大时土的强度较大,其压缩变形较小,非饱和重塑黄土的结构屈服压力较大;非饱和土基质吸力一定时,随着压力的增大,湿陷系数呈现出先增大后减小的趋势;同一净压缩应力下非饱和土基质吸力越大,湿陷系数越大,吸力越小,土样的?_s(p=200 k Pa)越小,当?_s(p=200 k Pa)超过约0.1时,?_s(p=200 k Pa)与基质吸力(u_a-u_w)近似呈指数增加。     

Effect of degree of saturation on mechanical behaviour of unsaturated soils and its elastoplastic simulation

The two stress-state variable approach has been widely used in interpreting unsaturated soil behaviour. However this approach cannot take into account the effect of degree of saturation or water contents on the stress–strain behaviour and strength of unsaturated soils. The triaxial test results presented in this paper show that even if the same path of net stress and suction is followed, the stress–strain relation and strength are different due to different degrees of saturation. When other conditions are the same, the higher the degree of saturation for the soil sample is, the higher the stress ratio corresponding to a given axial strain will be. This effect can be modeled by using an elasto-plastic constitutive model coupling hydraulic and mechanical behaviour of unsaturated soils. Comparisons between the predicted and measured results are presented, which demonstrate that the model can quantitatively simulate the influence of the degree of saturation on stress–strain behaviour and strength of unsaturated soils.     

Coupled modelling of hydro‐mechanical behaviour of unsaturated compacted expansive soils

The Barcelona basic model cannot predict the mechanical behaviour of unsaturated expansive soils, whereas the Barcelona expansive model (BExM) can only predict the stress–strain behaviour of unsaturated expansive soils without the water‐retention behaviour being incorporated. Moreover, the micro‐parameters and the coupling function between micro‐structural and macro‐structural strains in the BExM are difficult to determine. Experimental data show that the compression curves for non‐expansive soils under constant suctions are shifted towards higher void ratios with increasing suction, whereas the opposite is true for expansive soils. According to the observed water‐retention behaviour of unsaturated expansive soils, the air‐entry value increases with density, and the relationship between the degree of saturation and void ratio is linear at constant suction. According to the above observation, an elastoplastic constitutive model is developed for predicting the hydraulic and mechanical behaviour of unsaturated expansive soils, based on the existing hydro‐mechanical model for non‐expansive unsaturated soil. The model takes into consideration the effect of degree of saturation on the mechanical behaviour and that of void ratio on the water‐retention behaviour. The concept of equivalent void ratio curve is introduced to distinguish the plastic potential curve from the yield curve. The model predictions are compared with the test results of an unsaturated expansive soil, including swelling tests under constant net stress, isotropic compression tests and triaxial shear tests under constant suction. The comparison indicates that the model offers great potential for quantitatively predicting the hydraulic and mechanical behaviour of unsaturated expansive soils. Copyright © 2011 John Wiley & Sons, Ltd.     

On the use of effective stress in three-dimensional hydro-mechanical coupled model

In the last decades, a number of hydro-mechanical elastoplastic constitutive models for unsaturated soils have been proposed. Those models couple the hydraulic and mechanical behaviour of unsaturated soils, and take into account the effects of the degree of saturation on the stress–strain behaviour and the effects of deformation on the soil–water characteristic response with a simple reversible part for the hysteresis. In addition, the influence of the suction on the stress–strain behaviour is considered. However, until now, few models predict the stress–strain and soil–water characteristic responses of unsaturated soils in a fully three-dimensional Finite Element code. This paper presents the predictions of an unsaturated soil model in a Three-dimensional Framework, and develops a study on the effect of partial saturation on the stability of shallow foundation resting on unsaturated silty soil. Qualitative predictions of the constitutive model show that incorporating a special formulation for the effective stress into an elastoplastic coupled hydro-mechanical model opens a full range of possibilities in modelling unsaturated soil behaviour.     

不饱和土动弹塑性本构模型研究

以饱和度与有效应力为状态变量,通过引入描述不饱和与饱和土孔隙比差的状态变量,将Zhang等提出的饱和土体应力诱导各向异性动弹塑性本构模型推广到不饱和土体中,使其可描述不饱和土在动力循环荷载作用下的力学特性行为。通过对已有不饱和土体在完全不排水条件下的动三轴试验进行理论模拟,验证了所提出不饱和土本构模型的正确性。最后基于所提出本构模型,讨论了在不排水条件下初始饱和度对不饱和土动力特性研究。结果表明,不饱和土在动力荷载作用下,土体的孔隙比将减少,导致饱和度增加;当初始饱和度较高时,不饱和土会转化为饱和土,从而发生液化现象。该研究成果对研究不饱和土在地震等动力荷载作用下的力学特性行为具有重要意义。     

A unified constitutive model for unsaturated soil under monotonic and cyclic loading

This study presents a sophisticated elastoplastic constitutive model for unsaturated soil using Bishop-type skeleton stress and degree of saturation as state variables in the framework of critical state soil mechanism. The model is proposed in order to describe the coupled hydromechanical behavior of unsaturated soil irrespective of what kind of the loadings or the drainage conditions may be. At the same time, a water retention characteristic curve considering the influence of deformation on degree of saturation is also proposed. In the model, the superloading and subloading concepts are introduced to consider the influences of overconsolidation and structure on deformation and strength of soils. The proposed model only employs nine parameters, among which five parameters are the same as those used in Cam-Clay model. The other four parameters have the clear physical meanings and can be easily determined by conventional soil tests. The capability and accuracy of the proposed model have been validated carefully through a series of laboratory tests such as isotropic loading tests and triaxial monotonic and cyclic compression tests under different mechanical and hydraulic conditions.

     

A bounding surface model for unsaturated soils considering the microscopic pore structure and interparticle bonding effect due to water menisci

The interparticle bonding effect due to water menisci plays an important role in the hydromechanical coupling properties of unsaturated soils. This paper presents an unsaturated hydromechanical coupling model that considers the influence of matric suction, degree of saturation, and microscopic pore structure on the interparticle bonding effect. The enhanced effective stress and bonding variable are selected as constitutive variables. The bonding variable is correlated with the ratio between unsaturated void ratio and saturated void ratio. The deformation characteristics of unsaturated soils are described based on the bounding surface plasticity theory. A soil–water characteristic model that considers deformation and hydraulic hysteresis is integrated into the constitutive model to achieve hydromechanical coupling. The proposed model can effectively describe the hydromechanical coupling characteristics and the meniscus bonding force of unsaturated bimodal structure soils; the model parameters can be easily obtained through routine experiments. The experimental results of unsaturated isotropic compression, the wetting/drying cycle, and unsaturated triaxial shear tests are used to validate the capability of the proposed model.

     

非饱和土毛细滞回与变形耦合弹塑性本构模型

在修正剑桥模型的基础上,提出了一个非饱和土毛细滞回与骨架变形耦合的弹塑性本构模型。该模型考虑了基质吸力与饱和度对屈服应力的影响,可以同时描述非饱和土的弹塑性变形特性与毛细循环滞回效应。根据塑性体变的产生使非饱和土进气值增大的特点,建立了变形对土-水特征曲线影响的数学描述。该模型有效地考虑了饱和度对前期屈服应力的作用,准确地反映了土体在不同土-水状态条件下（脱湿和吸湿过程）强度特性的变化,而且还可以有效地描述水力循环历史对土体变形的影响。通过与试验数据对比,证明了该模型能够模拟非饱和土的主要力学特性。     

Interpretation of unsaturated soil behaviour in the stress – Saturation space,I: Volume change and water retention behaviour

Unsaturated soil behaviour, such as volume change, shear strength and yield stress, is usually interpreted and modelled in terms of stress and suction. This approach is consistent with laboratory tests where suction is a controllable variable. However, it also suffers some limitations. This paper (Parts I and II) presents an alternative approach for interpreting unsaturated soil behaviour, which is built in the space of stress versus degree of saturation. In Part I, a new volume change equation is proposed in terms of stress and degree of saturation, to give a better explanation to the non-linear change of soil compressibility under constant suctions. The soil compression index is assumed to be a function of the effective degree of saturation and is interpolated from the known compressibility at the fully saturated state and that at a dry state. An alternative approach to simulate hydraulic hysteresis and hydro-mechanical interaction is then introduced, which enables the calculation of the effective degree of saturation under complex stress and suction paths. The proposed volume change equation and the approach to describe saturation variation, which are two fundamental aspects to establish constitutive laws for unsaturated soils, are validated against a variety of experimental data in literature.     

Simulation of liquefaction of unsaturated soil using critical state soil model

Several researchers have reported that the mean effective stress of unsaturated soils having a relatively high degree of saturation gradually decreases under fully undrained cyclic loading conditions, and such soils can be finally liquefied like saturated soils. This paper describes a series of simulations of fully undrained cyclic loading on unsaturated soils, conducted using an elastoplastic model for unsaturated soils. This model is a critical state soil model formulated using effective stress tensor for unsaturated soils, which incorporates the following concepts: (a) the volumetric movement of the state boundary surface containing the critical state line owing to the variation in the degree of saturation; (b) the soil water characteristic curve considering the effects of specific volume and hydraulic hysteresis; and (c) the subloading surface concept for considering the effect of density. Void air is assumed to be an ideal gas obeying Boyle's law. The proposed model is validated through comparisons with past results. The simulation results show that the proposed model properly describes the fully undrained cyclic behavior of unsaturated soils, such as liquefaction, compression, and an increase in the degree of saturation. Finally, the effects of the degree of saturation, void ratio, and confining pressure on the cyclic strength of unsaturated soils are described by the simulation results. The liquefaction resistance of unsaturated soils increases as the degree of saturation and the void ratio decrease, and as the confining pressure increases. Furthermore, the degree of saturation has a greater effect on the liquefaction resistance than the confining pressure and void ratio. Copyright © 2017 John Wiley & Sons, Ltd.