Schmidt hammer and terrestrial laser scanning (TLS) used to detect single-event displacements on the Pleasant Valley fault (Nevada,USA)

Changes in surface roughness on carbonate fault scarps often reflect varying durations of subaerial weathering. On the Pleasant Valley fault in central Nevada, the documentation of a surface rupture in 1915, a long recurrence interval of faulting, slow weathering rate, and a relatively high (2–3 m) single-event displacement make the discrimination of the historical and penultimate slip patches unambiguous. Following from a 2018 study, we used a Schmidt hammer and terrestrial laser scanning (TLS) to further test whether these weathering patterns delineate exposed slip patches on a fault scarp. Results show that Schmidt hammer rebound value ranges (termed ΔR – the difference between minimum and maximum R-values in repeat impacts at a point), increase by ~8–10 points across the historical–penultimate event transition zone in two separate scarp transects. TLS-derived surface roughness also indicates a clear difference between the most recent and penultimate events. The average single-event displacement (SED) estimated using the Schmidt hammer and TLS is 2.85 m at two transect sites and is roughly equivalent to the visually estimated 3 m. While this fault is an ideal case where we know some of the slip history, the results demonstrate that these techniques show promise for discriminating slip patches on larger carbonate fault scarps with longer paleoearthquake histories, and could be used alongside ³⁶Cl cosmogenic exposure-age dating to improve paleoseismic records on normal faults. © 2019 John Wiley & Sons, Ltd.     

COSMOGENIC NUCLIDES EXPOSURE DATING FOR BEDROCK FAULT SCARP: RECONSTRUCTING THE PALEOEARTHQUAKE SEQUENCE

The bedrock scarps are believed to have recorded the continuous information on displacement accumulation and sequence of large earthquakes. The occurrence timing of large earthquakes is believed to be correlated positively with the exposure duration of bedrock fault surfaces. Accordingly, cosmogenic nuclides concentration determined for the bedrock footwall can offer their times, ages, and slip over long time. In general, multiple sites of fault scarps along one or even more faults are selected to carry out cosmogenic nuclide dating in an attempt to derive the temporal and spatial pattern of fault activity. This may contribute to explore whether earthquake occurrence exhibits any regularity and predict the timing and magnitude of strong earthquakes in the near future. Cosmogenic nuclide ³⁶ Cl dating is widely applied to fault scarp of limestone, and the height of fault scarp can reach as high as 15~20m. It is strongly suggested to make sure the bedrock scarp is exhumed by large earthquake events instead of geomorphic processes, based on field observation, and data acquired by terrestrial LiDAR and ground penetration radar (GPR). In addition, it is better for the fault surface to be straight and fresh with striations indicating recent fault movement. A series of bedrock samples are collected from the footwall in parallel to the direction of fault movement both above and below the colluvium, and each of them is~15cm long,~10cm wide, and~3cm thick. The concentrations of both cosmogenic nuclide ³⁶ Cl and REE-Y determined from these samples vary with the heights in parallel to fault scarps. Accordingly, we identify the times of past large earthquakes, model the profile of ³⁶ Cl concentration to seek the most realistic one, and determine the ages and slip of each earthquake event with the errors. In general, the errors for the numbers, ages, and slips of past earthquake events are ±1-2, no more than ±0.5-1.0ka, and ±0.25m, respectively.     

Schmidt hammer exposure‐age dating (SHD) of late Quaternary fluvial terraces in New Zealand

Schmidt hammer (SH) R‐values are reported for surface clasts from numerically dated Holocene and Pleistocene fluvial terraces in the South Island of New Zealand. The R‐values are combined with previously obtained weathering rind, radiocarbon, terrestrial cosmogenic nuclide and luminescence terrace ages to derive SH R‐value chronofunctions for greywacke clasts from four distinct locations. Our results show that different weathering rates affect the form of the SH R‐value versus Age curve, however a fundamental dependency between the two remains constant over timescales ranging from 10² to 10⁵ years. Power law scaling constants suggest changes in clast weathering rates are primarily affected by climatic (precipitation and temperature) and sedimentologic variables (source terrane petrology). Age uncertainties of ~22% of the surface age suggest that Schmidt hammer exposure‐age dating (SHD) is a reliable calibrated‐age dating technique for fluvial terraces. Copyright © 2013 John Wiley & Sons, Ltd.     

Use of the Acoustic Energy Meter (AEM) for rapid geomorphological field assessment of rock hardness: comparison with Schmidt hammer R‐value

Rapid, field‐based assessments of rock hardness are required in a broad range of geomorphological investigations where rock intact strength is important. Several different methods are now available for taking such measurements, in particular the Schmidt hammer, which has seen increasing use in geomorphology in recent decades. This is despite caution from within the engineering literature regarding choice of Schmidt hammer type, normalization of rebound (R‐) values, surface micro‐roughness, weathering degree and moisture content, and data reduction/analysis procedures. We present a pilot study of the use of an Acoustic Energy Meter (AEM), originally produced, tested and developed within the field of underground mining engineering as a rapid measure of rock surface hardness, and compare it with results from a mechanical N‐Type Schmidt hammer. We assess its capabilities across six lithological study sites in southeast Queensland, Australia, in the Greater Brisbane area. Each rock exposure has been recently exposed in the 20th/21st century. Using a ‘paired’ sampling approach, the AEM G‐value shows an inverse relationship with Schmidt hammer R‐value. While both devices show variability with lithology, the AEM G‐values show less scatter than the Schmidt hammer. We conclude that each device can contribute to useful rock hardness testing in geomorphological research, but the AEM requires further field testing in a range of environments, and in particular on older and naturally‐exposed rock surfaces. Future evaluations can extend this pilot study by focusing on sampling procedures, energy sources, and data reduction protocols, within the framework of a comparison study with other rock hardness testing apparatus. Copyright © 2016 John Wiley & Sons, Ltd.     

Monitoring degradation of the 1995 Nojima earthquake fault scarps at Awaji Island, southwestern Japan

The Nojima fault on the northwestern coast of Awaji Island, south of Kobe, was reactivated during the January 17, 1995 Hyogoken-nanbu earthquake. This fault rupture was dominated by right-lateral offset (max. 1.7 m) along a high-angle reverse fault which has a maximum vertical displacement of 1.3 m on the southeastern side. We repeatedly measured seven profiles across the fault scarp in two areas (Hirabayashi to the northeast and Ogura to the southwest) for approximately 1 year following the earthquake. The original profile of the fault scarp was an overhanging scarp at Hirabayashi and Ogura, corresponding to the 70–80 ° dip of the fault plane. The fault scarp at Hirabayashi displaces Plio-Pleistocene siltstones of the Osaka Group and is overlain by a thin bed of unconsolidated gravel. The Ogura area is entirely underlain by the Osaka Group. Scarp degradation at Hirabayashi occurred by collapse of the gravel bed and proceeded more quickly than at Ogura, where fault scarp degradation proceeded mainly by exfoliation of the Osaka Group siltstones. The degradation occurred at a very fast rate until March at Hirabayashi, and until June or July at Ogura. Since then, the degradation has been very slow. Our data strongly indicate that the scarp profile was initially controlled mainly by the dip of the fault plane, and scarp degradation has been primarily controlled by lithological factors. The degradation of the Nojima earthquake fault scarp proceeded much more quickly than that of normal fault scarps in the western U.S.A., where many observations of the initial stages of scarp degradation have been carried out. The extremely rapid degradation of the Nojima fault scarp in weak late Neogene siltstones might, in combination with rapid cultural modification of the landscape, explain the paucity of geomorphic scarps along the numerous active faults in Japan. This observation may also have implications for tectonic geomorphology and paleoseismicity studies in other countries characterised by weak bedrock and moderate to high rainfall regimes.     

Comparison of electronic and mechanical Schmidt hammers in the context of exposure‐age dating: are Q‐ and R‐values interconvertible?

Application of Schmidt‐hammer exposure‐age dating (SHD) to landforms has substantially increased in recent years. The original mechanical Schmidt hammer records R‐(rebound) values. Although the newly introduced electronic Schmidt hammer (SilverSchmidt) facilitates greatly improved data processing, it measures surface hardness differently, recording Q‐(velocity) values that are not a priori interconvertible with R‐values. This study is the first to compare the performance of both instruments in the context of field‐based exposure‐age dating with a particular focus on the interconvertibility of R‐values and Q‐values. The study was conducted on glacially polished pyroxene‐granulite gneiss, Jotunheimen, southern Norway. Results indicate that mean Q‐values are consistently 8–10 units higher than mean R‐values over the range of values normally encountered in the application of SHD to glacial and periglacial landforms. A convenient conversion factor of ±10 units may, therefore, be appropriate for all but the softest rock types close to the technical resolution of the instruments. The electronic Schmidt hammer should therefore be regarded as a useful complement and potential replacement for the mechanical Schmidt hammer. Conversion of published R‐values data to Q‐values requires, however, careful control and documentation of instrument calibration. Copyright © 2014 John Wiley & Sons, Ltd.     

Surface and sub‐surface Schmidt hammer rebound value variation for a granite outcrop

This study presents rock strength variations at granite outcrops and in subsurface vertical profiles in the Jizerské hory Mountains, Czech Republic. Schmidt hammer rebound values in subsurface profiles change gradually from the bedrock surface downward. An exponential relation has been observed between the R‐values and depth in rock outcrops to a depth of around 4·5 m. The exponential nature of the curve indicates that rock hardness increases more rapidly with depth in the uppermost 1?m section of the rock profile. A detailed study of rebound values obtained from both intact and polished rock exposures reveal effects of surface grinding on results of the Schmidt hammer method. The range of data collected increases after grinding, allowing more precise discrimination of rock surfaces in respect of age and weathering. The Schmidt hammer method may be used effectively as a relative‐age dating tool for rock surfaces that originated during the Late Pleistocene. It is concluded that this time limitation can be significantly mitigated by surface grinding before measurement. Copyright © 2010 John Wiley & Sons, Ltd.     

Physical modelling of fault scarp degradation under freeze–thaw cycles

Physical modelling has been developed in order to simulate the effects of periglacial erosion processes on the degradation of slopes and scarps. Data from 41 experimental freeze–thaw cycles are presented. They attest to the efficiency of periglacial processes that control both erosion and changes in scarp morphology: (i) cryoexpulsion leads to an increase of scarp surface roughness and modifies significantly the internal structure of the active layer; (ii) combined effects of frost creep and gelifluction lead to slow and gradual downslope displacements of the active layer (0·3 cm/cycle); (iii) debris flows are associated with the most significant changes in scarp morphology and are responsible for the highest rate of scarp erosion; (iv) quantification of the erosion rate gives values close to 1 cm³ cm^?2 for 41 freeze–thaw cycles. These experimental results are consistent with field data acquired along the La Hague fault scarp (Normandy, France) where an erosion rate of 4·6 ± 1 m³ m^?2 per glacial stage has been computed from the volume of natural slope deposits stored during the Weichselian glacial stage. These results show that moist periglacial erosion processes could lead to an underestimation of Plio‐Quaternary deformation in the mid‐latitudes. Copyright © 2006 John Wiley & Sons, Ltd.     

Field evidence for the influence of weathering on rock erodibility and channel form in bedrock rivers

Erosion processes in bedrock‐floored rivers shape channel cross‐sectional geometry and the broader landscape. However, the influence of weathering on channel slope and geometry is not well understood. Weathering can produce variation in rock erodibility within channel cross‐sections. Recent numerical modeling results suggest that weathering may preferentially weaken rock on channel banks relative to the thalweg, strongly influencing channel form. Here, we present the first quantitative field study of differential weathering across channel cross‐sections. We hypothesize that average cross‐section erosion rate controls the magnitude of this contrast in weathering between the banks and the thalweg. Erosion rate, in turn, is moderated by the extent to which weathering processes increase bedrock erodibility. We test these hypotheses on tributaries to the Potomac River, Virginia, with inferred erosion rates from ~0.1 m/kyr to >0.8 m/kyr, with higher rates in knickpoints spawned by the migratory Great Falls knickzone. We selected nine channel cross‐sections on three tributaries spanning the full range of erosion rates, and at multiple flow heights we measured (1) rock compressive strength using a Schmidt hammer, (2) rock surface roughness using a contour gage combined with automated photograph analysis, and (3) crack density (crack length/area) at three cross‐sections on one channel. All cross‐sections showed significant (p < 0.01 for strength, p < 0.05 for roughness) increases in weathering by at least one metric with height above the thalweg. These results, assuming that the weathered state of rock is a proxy for erodibility, indicate that rock erodibility varies inversely with bedrock inundation frequency. Differences in weathering between the thalweg and the channel margins tend to decrease as inferred erosion rates increase, leading to variations in channel form related to the interplay of weathering and erosion rate. This observation is consistent with numerical modeling that predicts a strong influence of weathering‐related erodibility on channel morphology. Copyright © 2017 John Wiley & Sons, Ltd.     

基于高分辨率地形数据的断层陡坎形态演化与强震活动关系研究

断层陡坎的形态可以保存有关断层带上地震活动等重要信息,陡坎上的坡折就是多次地震发生后陡坎演化留下的微地貌信息。以往研究选取的断层陡坎多为位于标准阶地面上的断层陡坎,而断层沿线地貌现象复杂,因此需要探索一种具有普适性的断层陡坎形态研究方法。本研究将常见的断层陡坎剖面按照形态划分为三种类型,以LiDAR技术获取的0.2m分辨率DEM数据为基础,选择了8个属于不同断层陡坎剖面类型的实验区,每个实验区采集不少于20条剖面,通过窗口检验确定研究区最佳数据获取移动窗口为7个像元并计算每条剖面的坡度值,通过坡度约束限定陡坎范围,进而识别坡折并获取坡折信息。对坡折信息进行概率密度统计,根据概率密度统计图中的峰值个数确定强震事件的次数。结果显示,陡坎形态研究结果与古地震探槽结果表现出较好的一致性,表明本文提出的陡坎形态研究方法可以适用于不同类型断层陡坎来确定强震事件次数。     

FAULTED LANDFORM AND SLIP RATE OF THE JINGHE SECTION OF THE BOLOKENU-AQIKEKUDUKE FAULT SINCE THE LATE PLEISTOCENE

The Bolokonu-Aqikekuduke fault zone(Bo-A Fault)is the plate convergence boundary between the middle and the northern Tianshan. Bo-A Fault is an inherited right-lateral strike-slip active fault and obliquely cuts the Tianshan Mountains to the northwest. Accurately constrained fault activity and slip rate is crucial for understanding the tectonic deformation mechanism, strain rate distribution and regional seismic hazard. Based on the interpretation of satellite remote sensing images and topographic surveys, this paper divides the alluvial fans in the southeast of Jinghe River into four phases, Fan1, Fan2, Fan3 and Fan4 by geomorphological elevation, water density, depth of cut, etc. This paper interprets gullies and terrace scarps by high-resolution LiDAR topographic data. Right-laterally offset gullies, fault scarps and terrace scarps are distributed in Fan1, Fan2b and Fan3. We have identified a total of 30 right-laterally offset gullies and terrace scarps. Minimum right-lateral displacement is about 6m and the maximum right-lateral displacements are(414±10)m, (91±5)m and(39±1)m on Fan2b, Fan3a and Fan3b. The landform scarp dividing Fan2b and Fan3a is offset right-laterally by (212±11)m. Combining the work done by the predecessors in the northern foothills of the Tianshan Mountains with Guliya ice core climate curve, this paper concludes that the undercut age of alluvial fan are 56~64ka, 35~41ka, 10~14ka in the Tianshan Mountains. The slip rate of Bo-A Fault since the formation of the Fan2b, Fan3a and Fan3b of the alluvial-proluvial fan is 3.3~3.7mm/a, 2.2~2.6mm/a and 2.7~3.9mm/a. The right-lateral strike-slip rate since the late Pleistocene is obtained to be 3.1±0.3mm/a based on high-resolution LiDAR topographic data and Monte Carlo analysis.     

Rare destructive earthquakes in Europe: The 1904 Bulgaria event case

Seismic hazard is difficult to assess in regions of low strain rates. A major limitation often relates to the absence of large instrumentally recorded events precluding any comparison between seismological data and paleoseismic or morphotectonic informations. We take advantage of the 1904 M_s∼7.1 earthquake that struck the southern edge of stable Eurasia and investigate if morphotectonic and paleoseismic observations can provide a reliable estimate of the seismic potential of slow-slipping faults. We have conducted a paleoseismic study of the Krupnik normal fault thought to be responsible for the event. A section of the fault bearing remnants of a 2 m-high scarp has been selected at the base of triangular facets. The trenching site locates where the scarp cuts across colluviums washed from the bedrock facetted slopes. We excavated two neighbouring trenches, one across a well-preserved portion of the scarp, and one across a portion degraded by a landslide. The excavations reveal a set of coarse colluvial units faulted against bedrock and affected by secondary fissures. Faulting appears to have resulted from a single event with normal throw greater than 1.3 m that occurred before the emplacement of the landslide. Accelerator Mass Spectrometry (AMS) radiocarbon dates of charcoal samples are consistent with the interpretation that the Krupnik Fault slipped recently, most probably in 1904, after a long lasting (> 10 ka) period of quiescence. The morphotectonic and paleoseismic observations yield seismic moment estimates compatible with the instrumental magnitude of the event and indicate that destructive and infrequent earthquakes typify the regional seismic behaviour.     

Paleoseismic indications along ‘aseismic’ fault segments in the guadalentín depression (SE Spain)

The Guadalentín Depression, located in SE Spain (Murcia Region), is bounded by two of the main NE-SW master faults of the Eastern Betics Cordilleras: The Lorca-Alhama and the Palomares left-lateral strike-slip faults. Available earthquake data indicate that, in the last 600 years, some sectors of the Lorca-Alhama Fault and the entire sector of the Palomares Fault have not been associated with significant historical seismicity. However, they show a wide range of diagnostic features of earthquake surface displacements on late Pleistocene and Holocene alluvial and colluvial surfaces. Aside from the left-lateral offsets recorded along 045–050 ° master fault strands of the Lorca-Alhama Fault, major paleoseismic surface displacements show different kinematics in relation to the broad orientation of the fault strands: (1) vertical normal displacements along 010–020 ° trending faults mainly preserved as degraded fault scarps of 2.5-1.8 m high (Aljibejo site); and (2) vertical reverse displacements, with average offsets of 0.2 – 1 m, along 065–080 ° subsidiary faults. In this last group, the younger one (Carraclaca Baths site) remains as a fault scarp of 0.8 m height affecting a cascade tufa which was active until the Spanish Roman Period (2nd Century B.C. to 6th Century A.D.). In other cases, reverse offsets resulted in smaller displacements (0.26 m) of paleosols, but show a recurrent behaviour (La Escarihuela site). The strongest earthquakes recorded in the study area did not exceed more than Mb 4.5 or MSK Intensity VIII (historical) with no evidence of coseismic rupture. Therefore, the preliminary data presented here seem to indicate that the paleoseismic activity on both faults is capable of producing coseismic surface displacements, probably reaching magnitudes of at least 6.5. These data show that paleoseismic studies based on geomorphological analyses are a useful tool in the assessment of the relative degree of activity of apparently ‘aseismic’ fault traces.     

Progressive changes in the morphology of fluvial terraces and scarps along the Rappahannock River,Virginia

Progressive geomorphic changes in the flight of fluvial terraces along the Rappahannock River, Virginia, provide a framework for analysing the effect of time on landforms. The oldest terrace is probably no younger than early Quaternary, and the youngest major fill terrace probably correlates with the high sea level of the last major interglacial. A uranium-series date of 187,000 yr has been obtained on coral from marine sediments related to this terrace. Indices of terrace preservation, especially drainage densities and area to perimeter ratios, show systematic changes with terrace age. Hence, these variables appear to satisfactorily indicate relative age, and could perhaps be used to estimate actual ages if suitably calibrated. The morphology of scarps formed by entrenchment of the fluvial terraces is more variable than analogous morphology of fault scarps and wave-cut bluffs. However, measurements of the fluvial scarps clearly indicate that for a given terrace age, higher scarps tend to have steeper slopes, and that for a given scarp height, older scarps tend to have gentler slopes. The terrace forms themselves are preserved for at least several million years. Depositional features such as bars and channels with l–3m of relief are preserved on terraces on the order of 10⁵ yr old. Scarps related to the formation of terraces of this age are well preserved and have slopes of about 6–8 degrees where the scarp height is about 5 m. The preservation of fluvial landforms and scarps suggests that, if fault scarps comparable to these features were commonly formed by earthquakes in low relief areas of the eastern United States, many should be recognizable.     

Paleoseismology of the 2016 MW 6.1 Petermann earthquake source: Implications for intraplate earthquake behaviour and the geomorphic longevity of bedrock fault scarps in a low strain-rate cratonic region

The 20 May 2016 M_W 6.1 Petermann earthquake in central Australia generated a 21 km surface rupture with 0.1 to 1 m vertical displacements across a low-relief landscape. No paleo-scarps or potentially analogous topographic features are evident in pre-earthquake Worldview-1 and Worldview-2 satellite data. Two excavations across the surface rupture expose near-surface fault geometry and mixed aeolian-sheetwash sediment faulted only in the 2016 earthquake. A 10.6 ± 0.4 ka optically stimulated luminescence (OSL) age of sheetwash sediment provides a minimum estimate for the period of quiescence prior to 2016 rupture. Seven cosmogenic beryllium-10 (¹⁰Be) bedrock erosion rates are derived for samples < 5 km distance from the surface rupture on the hanging-wall and foot-wall, and three from samples 19 to 50 km from the surface rupture. No distinction is found between fault proximal rates (1.3 ± 0.1 to 2.6 ± 0.2 m Myr⁻¹) and distal samples (1.4 ± 0.1 to 2.3 ± 0.2 m Myr⁻¹). The thickness of rock fragments (2–5 cm) coseismically displaced in the Petermann earthquake perturbs the steady-state bedrock erosion rate by only 1 to 3%, less than the erosion rate uncertainty estimated for each sample (7–12%). Using ¹⁰Be erosion rates and scarp height measurements we estimate approximately 0.5 to 1 Myr of differential erosion is required to return to pre-earthquake topography. By inference any pre-2016 fault-related topography likely required a similar time for removal. We conclude that the Petermann earthquake was the first on this fault in the last ca. 0.5–1 Myr. Extrapolating single nuclide erosion rates across this timescale introduces large uncertainties, and we cannot resolve whether 2016 represents the first ever surface rupture on this fault, or a > 1 Myr interseismic period. Either option reinforces the importance of including distributed earthquake sources in fault displacement and seismic hazard analyses.     

InSAR-DEM analyses integrated with geologic field methods for the study of long-term seismogenic fault behavior: Applications in the axial zone of the central Apennines (Italy)

The integration of terrain computer modeling with field methods may provide a powerful mechanism for understanding active faults geometry, kinematics and long-term fault behavior. Radar interferometry was used on ERS tandem images to create a geocoded DEM (InSAR-DEM) with a nominal 20-m spatial-resolution of the central Apennines axial zone, a seismically active area characterized by historical destructive earthquakes with M 7. The potential was tested of InSAR-DEM application to the Fucino and Sulmona basin boundary faults, which have well-defined seismological, paleoseismological and/or geological evidence for their having seismogenic sources. In particular, slope maps extracted from the InSAR-DEM were used for fault scarps detection, whether on carbonate bedrock (fault scarp type 2) or affecting continental deposits within the basin (fault scarp type 1), and compared with the available geological and new field data. In order to assess the DEM accuracy and to evaluate morphometric parameters related to the long-term slip-rates of the faults, a set of topographic profiles was extracted from the InSAR-DEM and compared with analogous profiles derived from the available topographic map (i.e., 1/25,000, with 25 m contour interval). In particular, the use of InSAR-DEM analyses showed its better results, with respect to the standard topography, for urban/agricultural gently sloped areas where fault scarps affected unconsolidated and particularly soft sediments (e.g., Fucino basin fault systems), while in severely sloped carbonate ridge and forested areas low coherences and layover effects made InSAR-DEM application problematic. A maximum value of 1.1 ± 0.2 mm yr^–1 slip-rate was obtained for the Fucino boundary fault. Finally, the recognized en-échelon pattern of the Sulmona basin boundary fault, provided a segmentation model for this structure corroborated by geological-structural field data.     

Surface-rupturing history of the Bree fault scarp, Roer Valley graben: Evidence for six events since the late Pleistocene

Since 1996 paleoseismological investigations have been used to develop the surface- rupturing history of the Bree fault scarp, the morphologically best-defined segment of the southwestern border fault of the Roer Valley graben in northeastern Belgium. The first studies determined that the escarpment is associated with a surface fault, and they exposed evidence for three surface displacements since about 40 ka BP. The most recent eventprobably occurred between 1000 and 1350 yr cal BP. Geophysical and trenching studies at a new site near the southeastern end of the fault scarp reconfirmed the coincidence of the frontal escarpment with a shallow normal fault, which displaces the Middle Pleistocene `Main Terrace' of the Maas River, as well as overlying coversands of Saalian to late Weichselian age. Different amounts of displacement shown by the two youngest coversand units indicate two discrete faulting events, but primary evidence for the coseismic nature of these events is sparse. Radiocarbon and optically stimulated luminescence dating constrainthe age of these events to the Holocene and between 14.0 ± 2.3 ka BP and 15.8 ± 2.9 ka BP, respectively. In addition, four older surface-rupturing events are inferred from the presence of four wedge-shaped units of reworked Main Terrace deposits that are interbedded with coversand units in the hanging wall of the trench and in shallow boreholes. These wedges are interpreted as colluvial wedges, produced by accelerated slope processes in response torejuvenation of the fault scarp, most probably in a periglacial environment. Luminescence dating indicates that five out of a total of six identified faulting events are younger than 136.6 ± 17.6 ka. The antepenultimate event was the largest faulting event, associated with a total fault displacement in excess of 1 m. Thus, the newly investigated trench site represents the longest and most complete record of surface rupturing recovered so far along the Bree fault scarp. This study also demonstrates the viability of the paleoseismological approach to identify past large earthquakes in areas of present-day moderate to low seismic activity.     

Process–form relationships in Southern Italian badlands: erosion rates and implications for landform evolution

Characteristic badlands are incised into Plio‐Pleistocene clays in Basilicata, southern Italy, creating steep, scarp slopes with knife‐edge ridges (calanchi) and small dome‐shaped forms (biancane). Erosion pin data for the period 1997–2003 give mean annual erosion rates for dome‐shaped biancane in the range 9–19 mm a^?1, while rates for the calanchi scarps are lower, at 7–10 mm a^?1. The erosion pin data also show a non‐linear relationship with slope angle. Maximum erosion rates coincide with a slope angle of 35°, within an envelope defined by combining the theoretical effects of both rainsplash and surface weathering. Monitoring of surface changes and erosion rates for two 0·5 m² cleared swathes on biancane forms reveals a complex relationship between weathering and erosion. Characteristic forms can develop from large blocks of intact clay bedrock over a time period of less than 30 a. The implications of the measured erosion rates for the landform association of mountain front/pediment/domed inselberg are explored. Copyright © 2005 John Wiley & Sons, Ltd.     

Microtopographic evolution of mineral surfaces as a tool to identify and date young fault scarps in bedrock

Faulting that results in surface ruptures through bedrock can be particularly difficult to date. For example, stratigraphic control on the age of faulting, based on the age of the bedrock, often leaves unacceptably large uncertainty on the age of the faulting. From a paleoseismological perspective, there is a clear need to determine if a bedrock fault scarp is actually a young feature. For young fault ruptures that create fresh mineral surfaces, analysis of microtopography developed by weathering of the mineral surface may provide a quantifiable method for determining the fault age. The direct quantitative measurement of mineral surface microtopography using Atomic Force Microscopy affords a novel method to study the rupture ages of active faults. The method for using microtopographic evolution of mineral surfaces depends on three conditions. The first condition is that freshly exposed mineral cleavage surfaces, which can be described geometrically as planes, are formed during a rupture event. The formation of these fresh surfaces is analogous to the initiation of a weathering ‘clock’ that defines time t=0. Following cleavage formation dissolution of the planar mineral surface occurs. The rate of dissolution for a mineral species under given climatic conditions, governs the rate of mineral surface alteration. Thus as dissolution proceeds, the roughness of the mineral surface increases. We suggest that the progression of microtopographic roughness over time, which can be estimated by computing quantitative statistics derived from digital mineral surface topography, will systematically vary until a steady state surface topography is reached. The fractal dimension, D_f, is one such measure of surface roughness where, D_f at time t=0 is 2. The dissolution of the mineral surface increases the fractal dimension as the removal of material proceeds. We posit that somewhere between D_f=2 and D_f=3, the microtopography reaches a steady state. Therefore, in the pre-steady state stage of surface roughness, the quantitative measure of roughness of the mineral may serve as a measure of time elapsed since faulting. The period of time this initial stage of surface roughening represents is dependent on the mineral and as a consequence, its dissolution rate, in a specific set of environmental conditions. The time elapsed since fault rupture and grain cleavage can also be estimated from the measurement of the volume of material removed through dissolution. If part of the original cleavage surface remains and can be identified then AFM measurements of the surface microtopography can be used to calculate the dissolved volume per unit area.     

Geologic evidence for late Quaternary repetitive surface faulting on the Isurugi fault along the northwestern margin of the Tonami Plain,north‐central Japan

Our detailed field investigation, paleoseismic trenching, and airborne light detection and ranging (LiDAR)‐derived topographic data provides the first direct evidence for late Quaternary repetitive surface faulting on the northeast‐striking Isurugi fault along the northwestern margin of the Tonami Plain in the Hokuriku region of north‐central Japan. This fault has been interpreted previously by different researchers as both inactive and active, owing to a lack of geologic evidence and a failure to identify fault‐related geomorphic features. Our mapping of LiDAR topography revealed a series of northeast‐trending warped fluvial terraces, about 1.5 km long and 170 m wide, with an age of ≤ 29 ka. We interpreted these geomorphologic features to represent an active pop‐up structure bounded to the southeast by the northwest‐dipping main thrust of the Isurugi fault and to the northwest by a southeast‐dipping backthrust that splays off the main thrust in the shallow subsurface. Paleoseismic trenching across the northwestern part of an elongate terrace exposed a series of southeast‐dipping backthrusts and associated northwest‐verging monoclines. The deformation and depositional age of the strata provide evidence for repetitive surface rupturing on the backthrusts since the latest Pleistocene; the latest of these events occurred in the Holocene between about 4.0 and 0.9 ka. Despite the poor preservation of the surface expression of the Isurugi fault, repetitive scarp‐forming faulting in the late Quaternary and the proximity of the Oyabe River and its tributaries to the fault trace suggest that there may be an extension of the Isurugi fault to the northeast and southwest beneath the Tonami Plain that makes the fault long enough to generate a large earthquake (Mw ≥ 6.8) accompanied by surface rupture.