首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 922 毫秒
1.
Erosion of hard‐rock coastal cliffs is understood to be caused by a combination of both marine and sub‐aerial processes. Beach morphology, tidal elevation and significant wave heights, especially under extreme storm conditions, can lead to variability in wave energy flux to the cliff‐toe. Wave and water level measurements in the nearshore under energetic conditions are difficult to obtain and in situ observations are rare. Here we use monthly cliff‐face volume changes detected using terrestrial laser scanning alongside beach morphological changes and modelled nearshore hydrodynamics to examine how exposed cliffs respond to changes in extreme wave conditions and beach morphology. The measurements cover the North Atlantic storms of 2013 to 2014 and consider two exposed stretches of coastline (Porthleven and Godrevy, UK) with contrasting beach morphology fronting the cliffs; a flat dissipative sandy beach at Godrevy and a steep reflective gravel beach at Porthleven. Beach slope and the elevation of the beach–cliff junction were found to influence the frequency of cliff inundation and the power of wave–cliff impacts. Numerical modelling (XBeach‐G) showed that under highly energetic wave conditions, i.e. those that occurred in the North Atlantic during winter 2013–2014, with Hs = 5.5 m (dissipative site) and 8 m (reflective site), the combination of greater wave height and steeper beach at the reflective site led to amplified wave run‐up, subjecting these cliffs to waves over four times as powerful as those impacting the cliffs at the dissipative site (39 kWm‐1 compared with 9 kWm‐1). This study highlighted the sensitivity of cliff erosion to extreme wave conditions, where the majority (over 90% of the annual value) of cliff‐face erosion ensued during the winter. The significance of these short‐term erosion rates in the context of long‐term retreat illustrates the importance of incorporating short‐term beach and wave dynamics into geomorphological studies of coastal cliff change. © 2017 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.  相似文献   

2.
Coastal cliff erosion is caused by a combination of marine forcing and sub-aerial processes, but linking cliff erosion to the environmental drivers remains challenging. One key component of these drivers is energy transfer from wave–cliff interaction. The aim of this study is to directly observe cliff ground motion in response to wave impacts at an individual wave scale. Measurements are described from two coastal cliff sites: a 45-minute pilot study in southern California, USA and a 30-day deployment in Taranaki, New Zealand. Seismometers, pressure sensors and video are used to compare cliff-top ground motions with water depth, significant wave height (Hs) and wave impact types to examine cliff ground motion response. Analyses of the dataset demonstrate that individual impact events can be discriminated as discrete events in the seismic signal. Hourly mean ground motion increases with incident Hs, but the largest hourly peak ground motions occurred across a broad range of incident Hs (0.9–3.7 m), including during relatively calm conditions. Mean hourly metrics therefore smooth the short-term dynamics of wave–cliff interaction; hence, to fully assess wave impact energy transfer to cliffs, it is important also to consider peak ground motion. Video analyses showed that the dominant control on peak ground motion magnitude was wave impact type rather than incident Hs. Wave–cliff impacts where breaking occurs directly onto the cliff face consistently produced greater ground motion compared to broken or unbroken wave impacts: breaking, broken and unbroken impacts averaged peak ground motion of 287, 59 and 38 μm s−1, respectively. The results illustrate a novel link between wave impact forcing and cliff ground motion response using individual wave field measurements, and highlight the influence of wave impact type on peak energy transfer to coastal cliffs. © 2019 John Wiley & Sons, Ltd. © 2019 John Wiley & Sons, Ltd.  相似文献   

3.
Influence of rock mass strength on the erosion rate of alpine cliffs   总被引:1,自引:0,他引:1  
Collapse of cliff faces by rockfall is a primary mode of bedrock erosion in alpine environments and exerts a first‐order control on the morphologic development of these landscapes. In this work we investigate the influence of rock mass strength on the retreat rate of alpine cliffs. To quantify rockwall competence we employed the Slope Mass Rating (SMR) geomechanical strength index, a metric that combines numerous factors contributing to the strength of a rock mass. The magnitude of cliff retreat was calculated by estimating the volume of talus at the toe of each rockwall and projecting that material back on to the cliff face, while accounting for the loss of production area as talus buries the base of the wall. Selecting sites within basins swept clean by advancing Last Glacial Maximum (LGM) glaciers allowed us to estimate the time period over which talus accumulation occurred (i.e. the production time). Dividing the magnitude of normal cliff retreat by the production time, we calculated recession rates for each site. Our study area included a portion of the Sierra Nevada between Yosemite National Park and Lake Tahoe. Rockwall recession rates determined for 40 alpine cliffs in this region range from 0·02 to 1·22 mm/year, with an average value of 0·28 mm/year. We found good correlation between rockwall recession rate and SMR which is best characterized by an exponential decrease in erosion rate with increasing rock mass strength. Analysis of the individual components of the SMR reveals that joint orientation (with respect to the cliff face) is the most important parameter affecting the rockwall erosion rate. The complete SMR score, however, best synthesizes the lithologic variables that contribute to the strength and erodibility of these rock slopes. Our data reveal no strong independent correlations between rockwall retreat rate and topographic attributes such as elevation, aspect, or slope angle. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

4.
This paper investigates the processes involved in unconsolidated cliff recession using LiDAR surveys (2005, 2010 and 2013) and aerial photographs (1964–2012) at Pointe‐au‐Bouleau, on the north shore of the St. Lawrence estuary, in eastern Canada. The high lithostratigraphic variability of the sediments allowed for the identification of stratigraphic and lithological variables that explain the evolution of coastal cliffs. Space‐for‐time substitution was also used to assess how lithostratigraphy controls the evolution of emerged glaciomarine coastal cliffs over decadal to centennial timescales. This case study presents new quantitative data that contributes to a better understanding of the role of sediment architecture, stratigraphy and geomorphology on coastal evolution. The methodological approach includes the development of a new conceptual model suitable for identifying erosion on cliff coastlines. The high spatial resolution methodology (<5 cm) used herein demonstrates the need for further research using LiDAR data in order to quantify the processes involved in the evolution of coastal cliffs. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

5.
Previous studies have estimated that coastal cliffs exist on about 80% of the global shoreline, but have not been validated on a global scale. This study uses two approaches to capture information on the worldwide existence and erosion of coastal cliffs: a detailed literature survey and imagery search, and a GIS-based global mapping analysis. The literature and imagery review show coastal cliffs exist in 93% of the combined recognized independent coastal states and non-independent coastal regions worldwide (total of 213 geographic units). Additionally, cliff retreat rates have been quantified in at least one location within 33% of independent coastal states and 15% of non-independent regions. The GIS-based mapping used the near-global Shuttle Radar Topography Mission 3 arc second digital elevation model and Arctic Coastal Dynamics Database to obtain near-global backshore coastal elevations at 1 km alongshore intervals comprising about 1,340,000 locations (81% of the world vector shoreline). Backshore coastal elevations were compared with the mapped distribution of European coastal cliffs to produce a model training set, and this relationship was extended globally to map the likelihood of coastal cliff locations. About 21% of the transects (17% of the world vector shoreline) were identified as mangroves and eliminated as potential cliff locations. The results were combined with estimates of cliff percentages for Greenland and Antarctica from the literature, extending the global coverage to estimate cliff occurrence across 89% of the world vector shoreline. The results suggest coastal cliffs likely exist on about 52% of the global shoreline. © 2018 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.  相似文献   

6.
Incised coastal gullies (ICGs) are dynamic features found at the terrestrial‐coastal interface. Their geomorphic evolution is driven by the interactions between processes of fluvial knickpoint migration and coastal cliff erosion. Under scenarios of future climate change the frequency and magnitude of the climatological drivers of both terrestrial (fluvial and hillslope) and coastal (cliff erosion) processes are likely to change, with an adjunct impact on these types of coastal features. Here we explore the response of an incised coastal gully to changes in both terrestrial and coastal climate in order to elucidate the key process interactions which drive ICG evolution. We modify an extant landscape evolution model, CHILD, to incorporate processes of soft‐cliff erosion. This modified version, termed the Coastal‐Terrestrial‐CHILD (CT‐CHILD) model, is then employed to explore the interactions between changing terrestrial and coastal driving forces on the future evolution of an ICG found on the south‐west Isle of Wight, UK. It was found that the magnitude and frequency of storm events will play a key role in determining the future trajectory of ICGs, highlighting a need to understand the role of event sequencing in future projections of landscape evolution. Furthermore, synergistic (positive) and antagonistic (negative) interactions were identified between coastal and terrestrial parameters, such as wave height intensity and precipitation duration, which act to modulate the impact of changes in any one parameter. Of note was the role played by wave height intensity in driving coastal erosion, which was found to play a more important role than sea‐level rise in determining rates of coastal erosion. This highlights the need for a greater focus on wave height in studies of soft‐cliff erosion. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

7.
A distinction is made between slumping and spalling. Slumping involves a compound slide with rotation and translation: the latter along one of the bedding plane shear surfaces in the Barton Beds. Spalling is an isolated failure of the exposed cliff face due to weathering. Where slumping is the dominant mode of cliff top recession, the latter is an incremental process with the increments being equal to the breadth of the slumps. A statistical study has been made of the breadth, length and plan area of 42 slumps observed over a 2 km stretch of the Christchurch Bay coastal cliffs and significant trends deduced.  相似文献   

8.
High-resolution rockfall inventories captured at a regional scale are scarce. This is partly owing to difficulties in measuring the range of possible rockfall volumes with sufficient accuracy and completeness, and at a scale exceeding the influence of localized controls. This paucity of data restricts our ability to abstract patterns of erosion, identify long-term changes in behaviour and assess how rockfalls respond to changes in rock mass structural and environmental conditions. We have addressed this by developing a workflow that is tailored to monitoring rockfalls and the resulting cliff retreat continuously (in space), in three-dimensional (3D) and over large spatial scales (>104 m). We tested our approach by analysing rockfall activity along 20.5 km of coastal cliffs in North Yorkshire (UK), in what we understand to be the first multi-temporal detection of rockfalls at a regional scale. We show that rockfall magnitude–frequency relationships, which often underpin predictive models of erosion, are highly sensitive to the spatial extent of monitoring. Variations in rockfall shape with volume also imply a systemic shift in the underlying mechanisms of detachment with scale, leading us to question the validity of applying a single probabilistic model to the full range of rockfalls observed here. Finally, our data emphasize the importance of cliff retreat as an episodic process. Going forwards, there will a pressing need to understand and model the erosional response of such coastlines to rising global sea levels as well as projected changes to winds, tides, wave climates, precipitation and storm events. The methodologies and data presented here are fundamental to achieving this, marking a step-change in our ability to understand the competing effects of different processes in determining the magnitude and frequency of rockfall activity and ultimately meaning that we are better placed to investigate relationships between process and form/erosion at critical, regional scales. © 2020 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd  相似文献   

9.
Concurrent observations of waves at the base of a southern California coastal cliff and seismic cliff motion were used to explore wave–cliff interaction and test proxies for wave forcing on coastal cliffs. Time series of waves and sand levels at the cliff base were extracted from pressure sensor observations programmatically and used to compute various wave impact metrics (e.g. significant cliff base wave height). Wave–cliff interaction was controlled by tide, incident waves, and beach sand levels, and varied from low tides with no wave–cliff impacts, to high tides with continuous wave–cliff interaction. Observed cliff base wave heights differed from standard Normal and Rayleigh distributions. Cliff base wave spectra levels were elevated at sea swell and infragravity frequencies. Coastal cliff top response to wave impacts was characterized using microseismic shaking in a frequency band (20–45 Hz) sensitive to wave breaking and cliff impacts. Response in the 20–45 Hz band was well correlated with wave–cliff impact metrics including cliff base significant wave height and hourly maximum water depth at the cliff base (r2 = 0.75). With site‐specific calibration relating wave impacts and shaking, and acceptable anthropogenic (traffic) noise levels, cliff top seismic observations are a viable proxy for cliff base wave conditions. The methods presented here are applicable to other coastal settings and can provide coastal managers with real time coastal conditions. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

10.
Development of a notch at the base of a cliff reduces cliff stability and often induces a collapse. Pleistocene limestone coastal cliffs of elevation 5?m in Kuro‐shima, Ryukyu Islands, have a prominent notch with a depth of 3–4?m at their bases. Around these coastal cliffs, collapses different from previous studies of cliff collapses in the Ryukyu Islands were found; collapses in Kuro‐shima have a horizontal failure surface. The horizontal failure surface, situated at the height of the failure surface corresponding to the retreat point of the notch, is bounded by vertical joints cutting the whole cliff and the reef flat in front of the cliff. Two types of horizontal failure surface were found, triangular and quadrangular; the distinction appears to depend on the angle between the vertical joints and the front face of the cliff. Prior to collapse, these cliffs appear to have been separated from the adjacent cliffs by the development of vertical joints. Consequently, a cliff that will collapse can be identified in advance; cliff instability is strongly dependent on the development of a notch. To study the effect of notch development on cliff collapse, the notch depth at which collapse occurs was calculated using stability analysis. Instability of a cliff increases with notch depth; collapse occurs at the horizontal failure surface when the ratio of the notch depth to the seaward length of the cliff is approximately 0·5–0·7 for a triangular failure surface, and 0·7–0·9 for a quadrangular failure surface. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

11.
Sediment dynamics below retreating cliffs   总被引:1,自引:0,他引:1  
The retreat of cliffs may constitute the dominant erosional response to base‐level fall in arid settings underlain by horizontally‐bedded sedimentary rock. These vertical cliffs typically loom above a relatively straight bedrock slope (‘plinth’) that is mantled with a thin layer of sediment and perched near the angle of repose. In detail, a plinth consists of a system of quasi‐parallel ridges and channels. We ask how the sediment supplied from a retreating cliff influences the erosion of the plinth hillslopes and channels, and how this affects the rate of cliff retreat. Motivated by field observations and high‐resolution topographic data from two sites in western Colorado, we develop a two‐dimensional (2D), rules‐based numerical model to simulate the erosion of channels draining a plinth and diffusive erosion of the intervening interfluves. In this model, retreat of a cliffband occurs when the height of the vertical cliff exceeds a threshold due to incision by channels on the plinth below. Debris derived from cliff retreat is distributed over the model plinth according to the local topography and distance from the source. This debris then weathers in place, and importantly can act to reduce local bedrock erosion rates, protecting both the plinth and ultimately the cliff from erosion. In this paper, we focus on two sets of numerical model experiments. In one suite, we regulate the rate of rockfall to limit the cliff retreat rate; in most cases, this results in complete loss of the plinth by erosion. In a second suite, we do not impose a limit on the cliff retreat rate, but instead vary the weathering rate of the rockfall debris. These runs result in temporally steady cliff‐plinth forms and retreat rates; both depend on the weathering rate of the debris. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

12.
Sea stacks are common and striking coastal landforms, but few details are known about how, how quickly, and under what conditions they form. We present numerical and analytical models of sea stack formation due to preferential erosion along a pre‐existing headland to address these basic questions. On sediment‐rich rocky coasts, as sea cliffs erode and retreat, they produce beach sediment that is distributed by alongshore sediment transport and controls future sea cliff retreat rates. Depending on their width, beaches can encourage or discourage sea cliff erosion by acting either as an abrasive tool or a protective cover that dissipates wave energy seaward of the cliff. Along the flanks of rocky headlands where pocket beaches are often curved and narrow due to wave field variability, abrasion can accelerate alongshore‐directed sea cliff erosion. Eventually, abrasion‐induced preferential erosion can cut a channel through a headland, separating it from the mainland to become a sea stack. Under a symmetrical wave climate (i.e. equal influence of waves approaching the coastline from the right and from the left), numerical and analytical model results suggest that sea stack formation time and plan‐view size are proportional to preferential erosion intensity (caused by, for example, abrasion and/or local rock weakness from joints, faults, or fractures) and initial headland aspect ratio, and that sea stack formation is discouraged when the sediment input from sea cliff retreat is too high (i.e. sea cliffs retreat quickly or are sand‐rich). When initial headland aspect ratio is too small, and the headland is ‘rounded’ (much wider in the alongshore direction at its base than at its seaward apex), the headland is less conducive to sea stack formation. On top of these geomorphic and morphologic controls, a highly asymmetrical wave climate decreases sea stack size and discourages stack formation through rock–sediment interactions. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

13.
We explore a new method for documenting the long-term retreat rate of seacliffs based on measurements and modeling of 10Be concentration transects across present-day shore platforms. The proposed forward numerical model relies on a scenario of sea-level rise since the last deglaciation, and predicts the shape of 10Be concentration transects as a function of prescribed cliff recession and vertical coastal platform downwearing rates. Two independent transect features allow fitting the long-term recession rate model to field observations: a sharp 10Be concentration drop predicted at the former stationary location of the cliff during the last glacial period ∼100 ka ago, and a characteristic dome shape whose magnitude is directly related to the recession rate of the cliff. A retreating chalk cliff site from the English Channel coast of France, at Mesnil-Val, where the 7 m tidal range broadly exposes the shore platform, was selected to test the proposed method. Although retreat rates were too high to pinpoint the predicted 10Be concentration drop at the last glacial cliff position, the 10Be concentration of the flints sampled across the shore platform is consistent with the expected dome shape. When modeled using the proper tidal range and proposed Holocene sea-level rise history, the 10Be data yield a cliff retreat rate since the mid-Holocene of 11–13 cm/yr. This is consistent with a 30-year-long measurement record, strongly supporting the utility of the 10Be method.  相似文献   

14.
Salt marsh cliff erosion in the Oosterschelde, due to basal scour and small-scale failure, was monitored during a two-year period using reference stakes. The composite marsh cliffs have a cantilever profile. Their stability is evaluated from beam failure analysis. A model is proposed, in which the cantilever weight is taken as the motive force; the major resistive force is the tensile strength. By substituting height, undermining width and soil mechanical properties of the cliff in the model, one can identify the cliffs that are likely to fail. Salt marsh cliffs, which combine a large tensile strength due to roots at the top of the profile with a large compressive stress at the cliff base due to the sandy texture of the subsoil, display the highest resistance to beam failure. The critical cliff dimensions, observed in the field, correspond with the values calculated from the proposed model of beam failure.  相似文献   

15.
Sea cliff morphology and erosion rates are modulated by several factors, including rock control that reflects both lithology and rock structure. Erosion is anticipated to preferentially exploit ‘fractures’, broadly meant as any discontinuity in an otherwise continuous medium, where the rock mass is weakest. Unpicking the direct control of such fractures on the spatial and temporal pattern of erosion remains, however, challenging. To analyse how such fractures control erosion, we monitored the evolution of a 400 m-long stretch of highly structured sedimentary cliffs in Socoa, Basque Country, France. The rock is known as the Socoa flysch formation. This formation combines decimetre-thick turbidites composed of repeat triplets of medium to strong calcareous sandstone, laminated siltstones and argillaceous marls. The sequence plunges at 45° into the sea with a shore-parallel strike. The cliffs are cross-cut by two normal and reverse fault families, with 10–100 m alongshore spacing, with primary and secondary strata-bound fractures perpendicular to the bedding, which combined delimit the cliff rock mass into discrete blocks that are exploited by the erosion process. Erosion, and sometimes plucking, of such beds and blocks on the cliff face was monitored using ground-based structure-from-motion (SfM) photogrammetry, over the course of 5.7 years between 2011 and 2017. To compare with longer time change, cliff-top retreat rate was assessed using SfM-orthorectified archive aerial photographs spanning 1954–2008. We show that the 13,250 m2 cliff face released 4500 blocks exceeding 1.45 × 10−3 m3, removing a total volume of 170 m3. This equates to an average cliff erosion rate of 3.4 mm/year, which is slightly slower than the 54-year-long local cliff-top retreat (10.8 ± 1.8 mm/year). The vertical distribution of erosion reflects the height of sea water inundation, where the maximum erosion intensity occurs ca. 2 m above high spring-tide water level. Alongshore, the distribution of rockfall scars is concentrated along bed edges bounding cross-cutting faults; the extent of block detachment is controlled by secondary tectonic joints, which may extend through several beds locally sharing similar mechanical strength; and rockfall depth is always a multiple of bed thickness. Over the longer term, we explain block detachment and resultant cliff collapse as a cycle. Erosion nucleates on readily exploitable fractures but elsewhere, the sea only meets defect-free medium-strong to strong rock slabs offering few morphological features for exploitation. Structurally delimited blocks are quarried, and with sufficient time, carve semi-elliptic scars reaching progressively deeper strata to be eroded. Lateral propagation of erosion is directed along mechanical weaknesses in the bedding, and large episodic collapses affect the overhanging slabs via sliding on the weak marl beds. Collapse geometry is confined to one or several triplets of turbidite beds, but never reaches deeper into the cliff than the eroded depth at the foot. We contend that this fracture-limited model of sea-cliff erosion, inferred from the Socoa site dynamics and its peculiar sets of fractures, applies more broadly to other fractured cliff contexts, albeit with site-specific geometries. The initiation of erosion, the propagation of incremental block release and the ultimate full failure of the cliff, have each been shown to be fundamentally directly controlled by structure, which remains a vital control in understanding how cliffed coasts have changed in the past and will change in the future.  相似文献   

16.
Cliff retreat in northern Boulonnais is described. The distribution of the amount of retreat is related to structural and topographic factors. Both control the runoff–infiltration balance and therefore the mechanical behaviour of the rocks, which determines the modes of failure. The spatial variability of the retreat rate is explained, but predicting the temporal variability of the retreat rate, which is central to risk management, is much more difficult. Rainfall and piezometric surface data enhanced a ‘piston flow’ mechanism during November 2000. The result of its occurrence on the stability of the cliff and conditions of its recurrence are examined with a view to better understanding the rate of recession of coastal cliffs and wiser management of risk. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

17.
Many boulders are located around the coastal cliffs with height of below 5 m made of coral limestone at Kuro‐shima, Okinawa, Japan. The origin of the boulders appears to be coral limestone cliffs which show developed notches. We undertook stability analysis, involving the wave pressure due to tsunamis, of wave‐induced collapse of the cliffs. We find that extreme waves are capable of inducing cliff collapse, as observed in circumstances where gravity is insufficient. Copyright © 2010 John Wiley and Sons, Ltd.  相似文献   

18.
Large cliff failures have often been characterized by their size in terms of the horizontal eroded area at the cliff top, and the maximum local retreat of the coastline. Field studies suggest that the frequencies of these two quantities decrease as power laws of their respective magnitudes, defining two different decay exponents. Moreover, the horizontal area increases as a power law of the maximum local retreat, identifying a third exponent. This observation indicates that the geometry of cliff failures are similar for different magnitudes. It is shown that, under a ‘scaling hypothesis’, the exponents satisfy a precise mathematical relation that relates the exponent of the distributions of magnitudes of events and their geometry – a relation that could be useful to validate the analysis of field catalogs. In order to understand the observed scenario, a numerical model of rocky coast erosion is developed. Despite its minimal character, it reproduces the observed cliff failure statistics. Strikingly, the model precisely reproduces the geometric similarity of cliff failures observed in the field. These results suggest that the theory of percolation, which underlies the erosion model, can possibly be used as a guide to decipher the physics of rocky coast erosion and could provide precise predictions of the statistics of cliff collapses. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

19.
We describe the immediate impact of the 14 November 2016 Kaikōura magnitude 7.8 (Mw) earthquake on shore platforms and cliffs around Kaikōura Peninsula. The earthquake caused an instantaneous uplift of ~1.01 m of the peninsula. We resurveyed seven profiles previously used for erosion monitoring and observed changes in the configuration of the shoreline. The coseismic uplift has fundamentally changed the process regime operating on the platforms and altered the future trajectory of shore platform and cliff development. Our observations highlight the interplay of waves, weathering, biology and tectonics. At this location tectonism strongly modulates the process regime, driving instantaneous changes in morphology and altering rates and patterns of erosion. Finally, the uplift of the Kaikōura coast has implications for changing resilience to climate change and sea level rise. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

20.
Three intrusive systems of detection and quantification of coastal erosion events (using thermocouples and thermal pins) were developed and tested from 2005 to 2008 in different regions of the Gulf and maritime estuary of the St Lawrence (Quebec, Canada). The 3‐m‐long thermal pins inserted inside unconsolidated deposits allow the monitoring of erosion for a time period sometimes extending over several seasons. The thermocouple or thermocable method allows not only the instrumentation of unconsolidated deposits but also of rocky and cohesive substrate to a depth of 85 cm. An autonomous microclimatic station located near the experimental sites simultaneously samples temperature parameters, precipitation, snow cover, wind speed and direction as well as global radiation. The differential analysis of cliff thermal regime performed simultaneously with an analysis of air temperature makes it possible to determine the activation periods of coastal erosion processes. The results also make it possible to establish with precision the actual influence of rapid variations of certain climatic and microclimatic parameters (radiation, presence of snow cover, precipitation, etc.) on the physical state of surfaces and also on the activation of certain physical processes connected to coastal erosion events. The automated thermal erosion pin system (ATEPS) allows high temporal resolution (i.e. continuous) monitoring, enabling a real coupling of coastal erosion rates and climatic parameters. Preliminary results with the ATEPS system indicate that mild winter temperature and direct solar radiation are significant factors controlling cliff retreat rates. Moreover, the melting of segregation ice during the spring thaw contributed for more than 70% of cliff retreat against only 30% for frost shattering. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号