水样及生物体内微量锌,锰,硒谱催化波同时测定

本文提出了在酒石酸盐－乙二胺－高氯酸－亚硫酸钠－高碘酸钾－ＥＤＴＡ体系中同时测定微量锌、锰、硒的极谱催化波，波峰每锐，波形稳定。Ｚｎ＾２＋浓度在０．４－４０μｇ／ｄｍ＾３，Ａｎ＾２＋浓度在１．６－８０μｇ／ｄｍ＾３，Ｓｅ浓度在０．０２－３．０μｇ／ｄｍ＾３内范围内浓度与峰电流呈线性关系。     

江阴岛海域溶解态Cu,Pb,Cd的含量及其与营养盐的关系

首次报道了福建省福清市江阴岛海域溶解态Ｃｕ，Ｐｂ，Ｃｄ的含量，并探讨了它们与营养盐的关系。１９９０年５月溶解态Ｃｕ，Ｐｂ，Ｃｄ的平均含量分别为０．８２、０．３８０、０．０２２μｇ／ｄｍ＾２，１０月的平均含量分别为０．７６、０．３８２、０．０３２μｇ／ｄｍ＾２。其５月溶解态Ｃｕ与无机氮Ｎ，硅酸盐间的线性回归相关式分别为Ｃｕ、（μｇ／ｄｍ＾３）＝０．４３８＋０．０３７７Ｎ（μｇ／ｄｍ＾３）、Ｃｕ（μｇ     

海水中硒标准物质的研制

本文介绍了海水中硒标准物质的研制过程，其中包括溶液的配制、均匀性和稳定性检验以及标样的分析方法。并对标准物质的定值数据进行统计处理，海水中硒两种浓度的定值结果分别为１．００±０．０５μｇ／ｃｍ３和２０．０±１．２μｇ／ｄｍ３。稳定期均为一年。     

粉煤灰海上倾倒中几种因素对Se^4＋溶出的影响

探讨了粉煤灰中的Ｓｅ＾４＋在海水中的溶出现象，找出了几种因素对Ｓｅ＾４＋从煤灰中溶出浓度的影响规律。结论是如果粉煤灰中硒的溶出率在１０％－２０％之间，将粉煤灰投入一个封闭海域，只要固液比达到１：１０００，海水中的硒含量就可达到２－３μｇ／Ｌ，即远远超过海水中硒含量的本底值０．０３μｇ／Ｌ。ＰＨ＝７时，盐度越高，温度越高越有利于粉煤灰中Ｓｅ＾４＋的溶出，从而使硒在封闭海域溶出值远高于海水硒含量的本底     

湄洲湾海域夏秋季溶解铜,镉,镍的分布特征

１９９２年６月湄洲湾海域溶解态Ｃｕ、Ｃｄ、Ｎｉ的含量范围（平均值）分别为０．３７￣３．２７（０．９０）、０．００９￣０．１３３（０．０２６）和０．４３￣１５．２０（２．０８）μｇ／ｄｍ＾３,１０月分别为０．４６￣１．９７（１．０８）、０．０１５￣０．８１（０．０２９）和０４６￣１３．０４（３．１５）μｇ／ｄｍ＾３。６月和１０Ｃｕ、Ｃｄ、Ｎｉ含量分布,除了与夏秋季不同水系消长和潮汐的影响有关外,还与     

伯劳特湾海水中~(239)Pu的浓度

伯劳特湾的表层海水中,２３９Ｐｕ的浓度为１３．０±２．８μＢｑ／ｄｍ３,与巴芬湾和拉布拉道海表层海水中的浓度基本相同。其中溶解２３９Ｐｕ的浓度为６．９３±１．８μＢｑ／ｄｍ３,占海水中２３９Ｐｕ总浓度的５３×１０－２;悬浮物中２３９Ｐｕ的浓度为６．０７±３．３μＢｑ／ｄｍ３,占总浓度的４７×１０－２。底层海水中２３９Ｐｕ的浓度为３１．７±４．７μＢｑ／ｄｍ３,２３８Ｐｕ的浓度为０．７８±０．７０μＢｑ／ｄｍ３,２３８Ｐｕ／２３９Ｐｕ的比值为０．０２４,这可能是表层沉积物重悬浮造成的。     

海水中砷标准物质的研制

本文介绍了海水中砷标准物质的研制过程，其中包括溶液的配制、均匀性和稳定性检验，标样的分析方法。并对标准物质的定值数据进行统计处理，两种浓度的定值结果分别为：１．００μｇ／ｃｍ３±０．０４μｇ／ｃｍ３和５１．０μｇ／ｄｍ３±２．６μｇ／ｄｍ３。两种浓度砷标准物质的稳定期均为一年     

九龙江口生物可利用磷的行为与人海通量

于１９９５年３、５月在九江口进行两个航次的现场调查,研究不同形态磷的河口行为,并估算生物可利用磷的入海通量。结果表明,在Ｓ〈２０区域内,溶解活性磷（ＤＲＰ）的行为受控于“缓冲机制”,其含量在８－１０μｇ／ｄｍ＾３水平上下波动。颗粒磷中ＭｇＣｌ２可提取磷（ＭｇＣｌ２－Ｐ）含量随盐度增大而增大,并与叶绿素ａ以及悬浮物Ｆｅ、Ｍｎ、Ａｌ含量呈正相关关系。ＮａＯＨ／ＮａＣｌ可提取磷（ＮａＯＨ／ＮａＣｌ－Ｐ）     

生长素QS在钝顶螺旋藻养殖中的应用

钝段螺旋藻（Ｓｐｉｒｕｌｉｎａ ｐｌａｔｅｎｓｉｓＧｅｉｔｌｅｒ）培养在低浓度ＮａＨＣＯ３（２～５ｇ／ｄｍ＾３）和适量生长素ＱＳ（０．５～５ｍｇ／ｄｍ＾３）中,研究了生长素ＱＳ对钝顶螺旋藻生长、生物量和生化组成的影响,结果表明,在生长素ＱＳ为１ｍｇ／ｄｍ＾３,ＮａＨＣＯ３浓度为５ｇ／ｄｍ＾３时,钝顶螺旋藻的生长最好,生物量、蛋白质及总碳水化合物的含量也与主浓度ＮａＨＣＯ３（８ｇ／ｄｍ＾３）培养条件下的基本相同,说明生物素ＱＳ的加入在一定程度上可降低ＮａＨＣＯ３的使用量,而不影响钝顶螺旋藻生长、生物量和生化组成。因而生长素ＱＳ在钝顶螺旋灌的养殖中可作为ＮａＨＣＯ３部分替代剂,从而达到降低养殖成本的目的。     

水库中几种主要微量营养元素的分布与变动

实验研究了一个中型水库（黄同水库）中几种主要微量营养元素（Ｆｅ、Ｍｎ、Ｚｎ、Ｃｕ、Ｍｏ）的存在形态、分布及其季节变动。主要结果为：（１）水库中Ｆｅ、Ｍｎ、Ｚｎ和Ｃｕ的平均总浓度分别为３６４．３、１１２．１、９６．０１和３．２４μｇ／Ｌ;Ｍｏ的溶解态平均浓度为３．２６μｇ／Ｌ。Ｆｅ和Ｍｎ以颗粒态为其主要存在形式,而Ｚｎ和Ｃｕ则以溶解态为主。（２）该水库５种微量元素的水平分布呈均匀化特征,但其浓度具有较明显的季节性变化。其垂直分布互有差异,Ｆｅ、Ｍｎ、Ｚｎ随水层深度增加而递减,而Ｃｕ和Ｍｏ的垂直变化甚小。（３）微量元素存在形态与水化学因子存在一定相关性,ＰＦｅ、ＰＺｎ、ＰＣｕ与ＤＯ间具有良好负相关,而ＤＺｎ、ＤＣｕ、ＤＭｏ和ＰＺｎ、ＰＦｅ与叶绿素间均呈紧密正相关。     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

Flow Cytometric Analysis of Coastal Lagoon Bacterioplankton and Picophytoplankton: Fixation and Storage Effects

The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics.