栅格新安江模型在天津于桥水库流域上游的应用

栅格新安江模型是在概念性新安江模型的理论基础上,以栅格为计算单元,结合地形地貌和下垫面特性构建出来的水文模型.在于桥水库流域上游的水平口流域应用栅格新安江模型,研究该地区洪水要素的空间变化以及洪水形成过程,讨论洪水模拟效果来验证模型在半湿润地区的适用性.选取水平口流域1978-2012年的洪水进行模型计算,模拟结果较好地反映了流域产流面积的时空变化,且均达到乙级以上精度.初步表明栅格新安江模型在半湿润地区有较好的适用性.     

SCE-UA方法在新安江模型参数优化中的应用

以前在使用新安江模型时人们遇到的最大困难可归因于缺乏有效的参数全局优化的数学方法,事实上对于一个缺乏经验的人来说,模型参数的人工试错计算的过程是一个相当不容易的过程,并且耗时颇多,为此,近些年来研究者们正在探索把概念性水文模型中的专家经验与自动优化计算相结合的方法或者数学优化中的全局优化方法,如SEC-UA方法,本文首先简述新安江模型,而后采用3个大小和气候条件各不相同的流域对SCE-UA算法就在新安江模型计算的参数优化进行了研究,研究结果表明,SCE-UA算法用来进行新安江模型的参数优化所取得的效果是好的,从率定和检验的结果来看,SCE-UA算法可以使得率定的新安江模型的参数达到全局最优并且从概念上也合理。     

WRF-Hydro模型与新安江模型在陈河流域的应用对比

本文利用全球陆面数据同化系统与降雨观测数据,以陕西半湿润区陈河流域为研究对象,驱动WRF-Hydro模型,研究该模型的表现和适用性,并在结构、参数、输入输出和模拟结果方面与新安江模型对比.考虑到次表面层与实际包气带的区别,引入土层厚度乘子ZSOILFAC对前者进行等比缩放,发现其与新安江模型反推包气带的厚度有较好的一致性.研究表明:在陈河流域中WRF-Hydro计算步长须在建议值的基础上缩小; WRF-Hydro模型善于模拟洪水细节,新安江模型表现好且稳定;前者的径流深和洪峰合格率平于或略低于后者;在两个指标均合格的洪水中,前者平均均方根误差比后者小21.5%,但对于其他洪水,前者平均均方根误差比后者大56.2%; WRF-Hydro在洪水起涨时刻模拟较好,表现出其在中小流域应用的潜力.     

新安江模型参数全局优化——以月潭流域为例

采用全局优化算法SCE-UA,以月潭流域为例对新安江模型参数优化进行研究.结果表明:采用理想资料时,SCEUA算法可以搜索到稳定的最优参数组;采用实际水文资料时,该算法不能保证得到唯一和稳定的最优参数组;对模型优化的目标函数进行探讨,发现对于新安江日模型,目标函数选取水量平衡误差函数或确定性系数函数较好,对于次洪模型选...     

应用新安江-海河模型研究下垫面变化对设计洪水的影响

为了探明流域产汇流参数变化特征及其演变机理,分析流域下垫面条件变化对设计洪水的影响.通过新安江海河模型研究卫河流域代表区下垫面变化情况,采用综合线性权重法对元村集站设计洪水资料系列进行一致性修正.结果表明:自由水蓄水容量、河网水流退水系数、地表填洼蓄水能力和地下水库出流初始水深这4个参数在1980年后都变大,可见代表区下垫面1980年前、后发生了明显的变化,导致流域内径流量大幅减少;合河—新村—五陵区间在1980年前15场洪水和1980年后32场洪水的预报径流深合格率都超过80%,达到乙等精度;元村集站最大5日洪量修正后比修正前平均减小27.1%;最大15日洪量修正后比修正前平均减小25.4%;最大30日洪量修正后比修正前平均减小23.0%.本研究可为水利工程的建设规模的确定提供科学依据,保障地区的防洪安全,满足人民生活和生产用水需求.     

新安江模型在资料匮乏的长江中下游山区中小流域洪水预报应用

水文资料匮乏流域的洪水预报(PUBs)是水文科学与工程中一个尚未解决的重大挑战.中国湿润山区中小流域大多是水文资料匮乏的流域,在此地区进行洪水预报的重要手段之一就是水文模型参数的估计.对基于参数物理意义的估算方法(以下简称物理估算法)及两种区域化方法进行了研究,将其用于新安江模型参数的估算及移植.皖南山区的29个中小流...     

基于无迹卡尔曼滤波的新安江模型实时校正方法

通过利用实时水文观测数据对洪水预报模型进行校正,可增加流域洪水预报的实时性和精确度.本文讨论了水文模型状态变量选取对滤波效果的影响,并给出了状态变量选取原则.在集总式新安江模型的基础上,结合状态变量选取原则,应用无迹卡尔曼滤波技术构建了新安江模型的实时校正方法.方法应用于闽江邵武流域洪水预报的计算结果表明,采用无迹卡尔曼滤波方法后,不仅能够直接校正模型状态,同时也能有效地提高模型预报精度,适合应用于实际流域洪水预报作业中.     

一种通过地形指数提取流域自由水蓄水容量空间分布的方法

对于分布式水文模型而言,如何获得参数的空间分布是模型应用的重点和难点问题.本文将分水源参数中的敏感参数——自由水蓄水容量为研究对象.建立地形指数与自由水蓄水容量的函数关系,以此提取流域内的自由水蓄水容量空间分布.最后利用本方法提取了陕西省陈河流域的自由水蓄水容量空间分布,并将之作为栅格型新安江模型的参数进行洪水模拟演算.应用结果表明本文提出的方法得到了理想的模拟结果.该方法以物理规律为基础能较为准确地计算出流域内自由水蓄水容量的空间分布,为分布式模型的发展奠定了坚实的基础.     

赣江流域多种数据同化方案的径流模拟比较

为了探讨水文模型在不同水文数据同化方案下的径流模拟差异,本文采用集合卡尔曼滤波算法,以遥感蒸散发产品、实测径流为观测数据,构建了基于新安江模型的数据同化框架。基于此框架设计了4种不同同化方案(DA-ET、DAET(K)、DA-ET-Q、DA-ET-Q(K))以及1种对照方案OL,以赣江流域开展实例研究,评估了水文数据同化中遥感蒸散发产品的时间分辨率、模型蒸散发相关参数时变与否以及多源数据同化对径流模拟的影响。结果表明:在DA-ET方案下,同化两种不同时间分辨率的蒸散发产品均能提高模型整体的径流模拟精度,且时间分辨率更高的产品的同化效果更好;在DA-ET方案的基础上,考虑加入实测径流进行同化能够提升模型径流模拟精度,且DA-ET(K)与DA-ET-Q(K)方案所得径流相对误差的减幅均超过了20%,说明在蒸散发同化过程中同时考虑蒸散发参数动态变化的结果更优;相较于OL方案,4种同化方案均能不同程度地提高模型对径流高水部分的模拟能力,但DA-ET-Q(K)方案表现最差,而其余方案差异并不显著。本研究有助于进一步了解不同数据同化方案在径流模拟中的差异,从而为水资源高效利用与科学管理提供科学依据...     

大尺度水文模型TOPX构建及其与区域环境系统集成模式RIEMS的耦合

基于改进型SIMTOP参数化径流方案和新安江模型的三层土壤水量平衡计算方法,本文构建了一个输入数据和率定参数较少、同时具有地形指数尺度转换机制、较好描述二维水文过程的简单高效的大尺度水文模型TOPX,并将其与区域环境系统集成模式RIEMS紧密耦合,以增强区域气候模式对大尺度流域径流量的定量数值模拟能力．TOPX模型在酉水河流域和泾河流域的离线测试表明：该模型对小尺度流域的径流量模拟精度较高,能够较好地描述流域水文变化过程;同时,该模型在大尺度上具有较强的分布式模拟能力,能够捕捉陆面水文过程的主要特征和时空演变特点．TOPX与RIEMS的耦合模式在泾河流域进行了在线测试,借助TOPX模型中的地形指数降尺度转换和水文过程产汇流机制,耦合模式实现了利用区域气候模式模拟的气象资料来驱动水文模型进行大尺度流域日径流量的模拟．进一步分析还表明：区域气候模式RIEMS模拟的降水时空分布数据的精度是影响耦合模式对径流量模拟效果的关键因素．     

Using TOPMODEL towards identifying and modelling the hydrological patterns within a headwater,humid, tropical catchment

Increasing pressure on the tropical environment requires a more thorough understanding of hydrological processes as part of reconciling the conflicting demands of economic development vis-à-vis sustainable land management. Using TOPMODEL, a physically based semi-distributed topohydrological model, we test its validity in modelling the stream flow dynamics (hydrograph) in a 1 ha tropical rainforest catchment in French Guiana. Another objective is through field validation of TOPMODEL to ascertain possible runoff generation mechanisms. The field validation of the temporal and spatial hydrodynamics across a rainfall–runoff event reveals that TOPMODEL may be suited for applications to this particular tropical rainforest environment; in fact, this is possibly the first successful application of such a model within the humid tropics. The main reasons why the model was successful are the presumed low hydraulic conductivities of the subsoil, coupled with the absence of an additional deep groundwater body, the contribution from which has caused difficulties in application of topographically, ‘physically’ based runoff models elsewhere in the humid tropics. © 1997 John Wiley & Sons, Ltd.     

Multi‐criterial validation of TOPMODEL in a mountainous catchment

The need for powerful validation methods for hydrological models including the evaluation of internal stages and spatially distributed simulations has often been emphasized. In this study a multi‐criterial validation scheme was used for validation of TOPMODEL, a conceptual semi‐distributed rainfall–runoff model. The objective was to test TOPMODEL's capability of adequately representing dominant hydrological processes by simple conceptual approaches. Validation methods differed in the type of data used, in their target and in mode. The model was applied in the humid and mountainous Brugga catchment (40 km²) in south‐west Germany. It was calibrated by a Monte Carlo method based on hourly runoff data. Additional information for validation was derived from a recession analysis, hydrograph separation with environmental tracers and from field surveys, including the mapping of saturated areas. Although runoff simulations were satisfying, inadequacies of the model structure compared with the real situation with regard to hydrological processes in the study area were found. These belong mainly to the concept of variable contributing areas for saturation excess overland flow and their dynamics, which were overestimated by the model. The simple TOPMODEL approach of two flow components was found to be insufficient. The multi‐criterial validation scheme enables not only to demonstrate limitations with regard to process representation, but also to specify where and why these limitations occur. It may serve as a valuable tool for the development of physically sound model modifications. Copyright © 1999 John Wiley & Sons, Ltd.     

Effects of the catchment runoff coefficient on the performance of TOPMODEL in rainfall–runoff modelling

Effects of the catchment runoff coefficient on the performance of TOPMODEL in simulating catchment rainfall–runoff relationships are investigated in this paper, with an aim to improve TOPMODEL's simulation efficiency in catchments with a low runoff coefficient. Application of TOPMODEL in the semi‐arid Yihe catchment, with an area of 2623 km² in the Yellow River basin of China, produced a Nash–Sutcliffe model efficiency of about 80%. To investigate how the catchment runoff coefficient affects the performance of TOPMODEL, the whole observed discharge series of the Yihe catchment is multiplied with a larger‐than‐unity scale factor to obtain an amplified discharge series. Then TOPMODEL is used to simulate the amplified discharge series given the original rainfall and evaporation data. For a set of different scale factors, TOPMODEL efficiency is plotted against the corresponding catchment runoff coefficient and it is found that the efficiency of TOPMODEL increases with the increasing catchment runoff coefficient before reaching a peak (e.g. about 90%); after the peak, however, the efficiency of TOPMODEL decreases with the increasing catchment runoff coefficient. Based on this finding, an approach called the discharge amplification method is proposed to enhance the simulation efficiency of TOPMODEL in rainfall–runoff modelling in catchments with a low runoff coefficient. Copyright © 2004 John Wiley & Sons, Ltd.     

Modelling the chloride signal at Plynlimon,Wales, using a modified dynamic TOPMODEL incorporating conservative chemical mixing (with uncertainty)

The application of a modified version of dynamic TOPMODEL for two subcatchments at Plynlimon, Wales is described. Conservative chemical mixing within mobile and immobile stores has been added to the hydrological model in an attempt to simulate observed stream chloride concentrations. The model was not fully able to simulate the observed behaviour, in particular the short‐ to medium‐term dynamics. One of the primary problems highlighted by the study was the representation of dry deposition and cloud‐droplet‐deposited chloride, which formed a significant part of the long‐term chloride mass budget. Equifinality of parameter sets inhibited the ability to determine the effective catchment mixing volumes and coefficients or the most likely partition between occult mass inputs and chloride mass inputs determined by catchment immobile‐store antecedent conditions. Some success was achieved, in as much as some aspects of the dynamic behaviour of the signal were satisfactorily simulated, although spectral analysis showed that the model could not fully reproduce the 1/f power spectra of observed stream chloride concentrations with its implications of a wide distribution of residence times for water in the catchment. Copyright © 2006 John Wiley & Sons, Ltd.     

Sensitivity analysis of extended TOPMODEL for agricultural watersheds equipped with tile drains

An extension of TOPMODEL was developed for rainfall–runoff simulation in agricultural watersheds equipped with tile drains. Tile drain functions are incorporated into the framework of TOPMODEL. Nine possible flow generation scenarios are suggested for tile-drained watersheds and applied in the modelling procedure. In the model development, two methods of simulation of the flow in the unsaturated zone were compared: the traditional, physically based storage approach and a new approach using a transfer function. A regionalized sensitivity analysis was used to determine the sensitivity of parameters and to compare the behaviour of the transfer function with that of the simple storage-related formulation. The number of accepted combinations of parameter values, on average, was higher for the transfer function approach than when using a Monte Carlo method of parameter estimation. Since the rainfall–runoff response pattern tends to vary seasonally, seven events distributed throughout a year were used in the sensitivity analysis to investigate the seasonal variation of the hydrological characteristics. © 1997 John Wiley & Sons, Ltd.     

Simulation and comparative study of two types of Topographic Index model for a homogeneous mountain catchment

In order to expand the application range of the classic Topographic Index model (TOPMODEL) and develop a more appropriate submodel of hydrological processes for use in the land surface model, two types of TOPMODEL are investigated, one with saturated hydraulic conductivity change with depth obeying exponential law (classical e-TOPMODEL or e-TOPMODEL for short) and the other obeying general power law (general p-TOPMODEL or p-TOPMODEL for short). Using observation date in the Suomo River catchment located in the upper reaches of the Yangtze River, the sensitivity study of the p-TOPMODEL was conducted and the simulated results from the model were examined and evaluated first, and then the results were compared with the results from the e-TOPMODEL to find the similarities and differences between the two types of models. The main conclusions obtained from the above studies are (1) topographic index and its distribution derived from the p-TOPPMODEL for the Suomo Basin are sensitive to changes of parameter n and m; (2) changes of n and m have impacts on the simulation results of various hydrological components (such as daily runoff, monthly averaged runoff, monthly averaged surface runoff and subsurface runoff), but have the weaker impacts on forty-year averaged total runoff; and (3) for the same value of m, the simulated results of e-TOPMODEL display higher surface runoff and lower subsurface runoff than the general p-TOPMODEL does but multi-year averaged total runoffs produced from the two types of TOPMODEL show insignificant difference. The differences between the two types of models indicate that it is necessary to pay close attention to correct selection from different hydrological models for use in land surface model development. The result mentioned above is useful to provide some referential information for the model selection.     

A BTOP model to extend TOPMODEL for distributed hydrological simulation of large basins

Topography is a dominant factor in hillslope hydrology. TOPMODEL, which uses a topographical index derived from a simplified steady state assumption of mass balance and empirical equations of motion over a hillslope, has many advantages in this respect. Its use has been demonstrated in many small basins (catchment areas of the order of 2–500 km²) but not in large basins (catchment areas of the order of 10 000–100 000 km²). The objective of this paper is to introduce the Block‐wise TOPMODEL (BTOP) as an extension of the TOPMODEL concept in a grid based framework for distributed hydrological simulation of large river basins. This extension was made by redefining the topographical index by using an effective contributing area af(a) (0?f(a)?1) per unit grid cell area instead of the upstream catchment area per unit contour length and introducing a concept of mean groundwater travel distance. Further the transmissivity parameter T₀ was replaced by a groundwater dischargeability D which can provide a link between hill slope hydrology and macro hydrology. The BTOP model uses all the original TOPMODEL equations in their basic form. The BTOP model has been used as the core hydrological module of an integrated distributed hydrological model YHyM with advanced modules of precipitation, evapotranspiration, flow routing etc. Although the model has been successfully applied to many catchments around the world since 1999, there has not been a comprehensive theoretical basis presented in such applications. In this paper, an attempt is made to address this issue highlighted with an example application using the Mekong basin. Copyright © 2007 John Wiley & Sons, Ltd.     

辽河太子河流域藻类植物群落结构及其季节变化

2010年9月到2011年9月分4次对太子河流域的藻类植物群落组成、丰度及优势种进行调查分析.共设置17个采样点,经鉴定共有藻类植物8门120属328种(包括21种变种).藻类植物群落以硅藻最多,有36属144种,占总体的43.77%;其次是绿藻,有49属117种,占总体的35.56%;蓝藻居第3位,有22属38种,占总体的11.85%.调查期间,太子河流域藻类植物细胞丰度在夏、秋季较高,丰度平均值分别为6.80×10⁷和3.29×10⁷cells/L;在春季较低,丰度平均值为1.36×10⁷cells/L.优势度分析显示,太子河流域各季节的藻类植物优势种都在5种以上,主要优势种有巨颤藻(Oscillatoria princeps Vauch.)、链丝藻(Hormidium flaccidum(Kütz.)Br.)、偏生毛枝藻(Stigeoclonium subsecundum(Kütz.)Haz.)等.藻类植物的Jaccard种类相似性指数在0.19~0.46之间.太子河流域藻类植物种类组成及细胞丰度均有明显的季节变化.     

Comparison of evapotranspiration variations between the Yellow River and Pearl River basin, China

Based on daily meteorological data at 43 gauging stations in the Pearl River basin and 65 gauging stations in the Yellow River basin, we analyze changing properties of actual evapotranspiration (ET_a), reference evapotranspiration (ET_ref) and precipitation in these two river basins. In our study, Pearl River basin is taken as the ‘energy-limited’ system and the Yellow River basin as the ‘water-limited’ system. The results indicate decreasing ET_a in the Pearl River and Yellow River basin. However, different changing properties are detected for ET_ref when compared to ET_a. The middle and upper Yellow River basin are characterized by increasing ET_ref values, whereas the Pearl River basin is dominated by decreasing ET_ref values. This result demonstrates enhancing drying force in the Yellow River basin. ET_a depends mainly on the changes of precipitation amount in the Yellow River basin. In the Pearl River basin, however, ET_a changes are similar to those of ET_ref, i.e. both are in decreasing trend and which may imply weakening hydrological cycle in the Pearl River basin. Different influencing factors are identified behind the ET_a and ET_ref in the Pearl River and Yellow River basin: In the Pearl River basin, intensifying urbanization and increasing aerosol may contribute much to the evapotranspiration changes. Variations of precipitation amount may largely impact the spatial and temporal patterns of ET_a in the Yellow River basin. The current study is practically and scientifically significant for regional assessment of water resource in the arid and humid regions of China under the changing climate.