地震作用下公路桥梁碰撞的半主动控制研究

针对地震作用下公路桥梁的碰撞问题,采用接触单元法模拟桥梁之间的碰撞作用,并在此基础上研究了采用磁流变阻尼器的公路桥梁碰撞的半主动控制方法。通过对某公路桥梁的数值模拟发现,地震作用下桥梁之间的相互碰撞,将大幅增加桥梁的绝对加速度响应。采用磁流变阻尼器的半主动控制系统能够较好地降低结构的地震响应和消除地震作用下的碰撞。     

地震作用下隔震简支梁桥碰撞反应的振动台试验

由地震引发的碰撞是影响桥梁地震反应以及造成桥梁破坏的重要因素。本文对地震作用下隔震简支梁桥的碰撞反应进行了振动台试验。设计制作1个两跨简支的隔震梁桥模型,试验研究了梁间隙、邻梁质量比、隔震支座类型等参数对桥梁碰撞反应的影响。试验结果表明邻梁间隙、邻梁质量比、隔震支座类型等参数对桥梁的碰撞反应有着显著的影响。邻梁间隙越大,碰撞次数越少;邻梁质量比越大,撞击力越大。铅芯橡胶支座比板式橡胶支座耗能能力更强,可以有效降低邻梁之间的撞击力甚至避免碰撞发生。从而为桥梁防碰撞设计提供了可靠的试验依据。     

Experimental study of a highway bridge with shape memory alloy restrainers focusing on the mitigation of unseating and pounding

This paper presents an experimental study to investigate the performance of shape memory alloy(SMA) restrainers for mitigating the pounding and unseating of highway bridges when subjected to seismic excitations.Mechanical property tests of the SMA wire used in the restrainers are conducted first to understand the pseudo-elastic characteristics of the material.Then,a series of shaking table tests are carried out on a highway bridge model.The structural responses of the highway bridge model equipped with SMA restrainers,installed in the form of deck-deck and deck-pile connections,are analyzed and compared with the uncontrolled structures.The test results of this study indicate that the SMA restrainers are not only effective in preventing unseating but also in suppressing the seismic-induced pounding of the highway bridge model used in this study.     

Experimental verification of torsional response control of asymmetric buildings using MR dampers

This paper proposes a semiactive control system to reduce the coupled lateral and torsional motions in asymmetric buildings subjected to horizontal seismic excitations. Magnetorheological (MR) dampers are applied as semiactive control devices and the control input determination is based on a clipped‐optimal control algorithm which uses absolute acceleration feedback. The performance of this method is studied experimentally using a 2‐story building model with an asymmetric stiffness distribution. An automated system identification methodology is implemented to develop a control‐oriented model which has the natural frequencies observed in the experimental system. The parameters for the MR damper model are identified using experimental data to develop an integrated model of the structure and MR dampers. To demonstrate the performance of this control system on the experimental structure, a shake table is used to reproduce an El Centro 1940 N–S earthquake as well as a random white noise excitation. The responses for the proposed control system are compared to those of passive control cases in which a constant voltage is applied to the MR damper. Copyright © 2003 John Wiley & Sons, Ltd.     

Reduction of pounding effects in elevated bridges during earthquakes

Pounding of adjacent superstructure segments in elevated bridges during severe earthquakes can result in significant structural damage. The aim of this paper is to analyse several methods of reduction of the negative effects of collisions induced by the seismic wave propagation effect. The analysis is conducted on a detailed three‐dimensional structural component model of an isolated highway bridge. The results show that the influence of pounding on the structural response is significant in the longitudinal direction of the bridge and significantly depends on the gap size between superstructure segments. The smallest response can be obtained for very small gap sizes and for gap sizes large enough to prevent pounding. Further analysis indicates that the bridge behaviour can be effectively improved by placing hard rubber bumpers between segments and by stiff linking the segments one with another. The experimental results show that, for the practical application of such connectors, shock transmission units can be used. Copyright © 2000 John Wiley & Sons, Ltd.     

形状记忆合金橡胶对高架桥梁碰撞减震效果的试验研究

地震作用下,高架桥梁相邻主梁间的碰撞会引起结构位移和加速度响应增大、应力提高,导致混凝土开裂、脱落和伸缩缝被挤压破坏,甚至引发桥梁落梁和倒塌等,因此采取减轻或者避免桥梁结构在地震作用下碰撞的措施显得尤为必要。设计制备了具有变形自恢复能力的形状记忆合金橡胶碰撞缓冲器,通过桥梁地震碰撞的振动台试验,研究了形状记忆合金橡胶缓冲器对桥梁碰撞的控制效果,提出了碰撞缓冲器吸能效率和结构自身耗能控制率指标。研究表明,形状记忆合金橡胶碰撞缓冲器具有稳定的吸能效率,能够大幅度降低桥梁结构碰撞加速度和碰撞力,这对于提高城市交通网络的地震安全性能具有重要意义。     

Influence of ground motion spatial variation,site condition and SSI on the required separation distances of bridge structures to avoid seismic pounding

It is commonly understood that earthquake ground excitations at multiple supports of large dimensional structures are not the same. These ground motion spatial variations may significantly influence the structural responses. Similarly, the interaction between the foundation and the surrounding soil during earthquake shaking also affects the dynamic response of the structure. Most previous studies on ground motion spatial variation effects on structural responses neglected soil–structure interaction (SSI) effect. This paper studies the combined effects of ground motion spatial variation, local site amplification and SSI on bridge responses, and estimates the required separation distances that modular expansion joints must provide to avoid seismic pounding. It is an extension of a previous study (Earthquake Engng Struct. Dyn. 2010; 39 (3):303–323), in which combined ground motion spatial variation and local site amplification effects on bridge responses were investigated. The present paper focuses on the simultaneous effect of SSI and ground motion spatial variation on structural responses. The soil surrounding the pile foundation is modelled by frequency‐dependent springs and dashpots in the horizontal and rotational directions. The peak structural responses are estimated by using the standard random vibration method. The minimum total gap between two adjacent bridge decks or between bridge deck and adjacent abutment to prevent seismic pounding is estimated. Numerical results show that SSI significantly affects the structural responses, and cannot be neglected. Copyright © 2010 John Wiley & Sons, Ltd.     

Seismic response control of smart sliding isolated buildings using variable stiffness systems: an experimental and numerical study

Effectiveness of a new semiactive independently variable stiffness (SAIVS) device in reducing seismic response of sliding base isolated buildings is evaluated analytically and experimentally. Through analytical and experimental study of force—displacement behaviour of the SAIVS device, it is shown that the device can vary stiffness continuously and smoothly between minimum and maximum stiffness. Passive sliding base isolation systems reduce interstorey drifts and superstructure accelerations, but with increased base displacements, which is undesirable, under large velocity near fault pulse type earthquakes. It is a common practice to incorporate non‐linear passive dampers into the isolation system to reduce bearing displacements. Incorporation of passive dampers, however, may result in increased superstructure accelerations and drifts; while, properly designed passive dampers can be beneficial. A viable alternative is to use semiactive variable stiffness systems, which can vary the period of the sliding base isolated buildings in real time, to simultaneously reduce bearing displacements and superstructure responses further than the passive systems, which deserves investigation. This study investigates the performance of a 1:5 scaled smart sliding base isolated building model equipped with the SAIVS device analytically and experimentally, under near fault earthquakes, by developing a new moving average non‐linear tangential stiffness control algorithm for control of the SAIVS device. The SAIVS device reduces bearing displacements further than the passive cases, while maintaining isolation level forces and superstructure responses at the same level as the passive minimum stiffness case, indicating the significant potential of the SAIVS system. Copyright © 2005 John Wiley & Sons, Ltd.     

Semi‐active control of sliding isolated bridges using MR dampers: an experimental and numerical study

Sliding base‐isolation systems used in bridges reduce pier drifts, but at the expense of increased bearing displacements under near‐source pulse‐type earthquakes. It is common practice to incorporate supplemental passive non‐linear dampers into the isolation system to counter increased bearing displacements. Non‐linear passive dampers can certainly reduce bearing displacements, but only with increased isolation level forces and pier drifts. The semi‐active controllable non‐linear dampers, which can vary damping in real time, can reduce bearing displacements without further increase in forces and pier drifts; and hence deserve investigation. In this study performance of such a ‘smart’ sliding isolation system, used in a 1:20 scaled bridge model, employing semi‐active controllable magneto‐rheological (MR) dampers is investigated, analytically and experimentally, under several near‐fault earthquakes. A non‐linear analytical model, which incorporates the non‐linearities of sliding bearings and the MR damper, is developed. A Lyapunov control algorithm for control of the MR damper is developed and implemented in shake table tests. Analytical and shake table test results are compared. It is shown that the smart MR damper reduces bearing displacements further than the passive low‐ and high‐damping cases, while maintaining isolation level forces less than the passive high‐damping case. Copyright © 2005 John Wiley & Sons, Ltd.     

Experimental verification of a wireless sensing and control system for structural control using MR dampers

The performance aspects of a wireless ‘active’ sensor, including the reliability of the wireless communication channel for real‐time data delivery and its application to feedback structural control, are explored in this study. First, the control of magnetorheological (MR) dampers using wireless sensors is examined. Second, the application of the MR‐damper to actively control a half‐scale three‐storey steel building excited at its base by shaking table is studied using a wireless control system assembled from wireless active sensors. With an MR damper installed on each floor (three dampers total), structural responses during seismic excitation are measured by the system's wireless active sensors and wirelessly communicated to each other; upon receipt of response data, the wireless sensor interfaced to each MR damper calculates a desired control action using an LQG controller implemented in the wireless sensor's computational core. In this system, the wireless active sensor is responsible for the reception of response data, determination of optimal control forces, and the issuing of command signals to the MR damper. Various control solutions are formulated in this study and embedded in the wireless control system including centralized and decentralized control algorithms. Copyright © 2007 John Wiley & Sons, Ltd.     

Transient responses of girder bridges with vertical poundings under near‐fault vertical earthquake

Previous studies on pounding responses of bridge structures mainly focus on the horizontal pounding between adjacent structures. However, the vertical pounding responses of bridge are rarely studied. The aim of this paper is develop a theoretical approach to investigate the transient behavior of continuous bridge under near‐fault vertical ground motions. The transient behavior of bridge manifests as the earthquake‐induced response wave and pounding‐induced response wave travel throughout bridge. Based on a new continuous model of beam–spring–rod, the theoretical solution of bridge responses involving multiple vertical poundings is derived by the expansion of transient wave functions in a series of eigenfunctions. A new theoretical solving approach of the multiple vertical pounding forces is presented based on the transient internal force on the contact surface of the girder and bearing. The numerical results show that the present method can reasonably capture the propagations of the earthquake‐induced response wave and pounding‐induced response wave. The calculations of pounding force by the present method are convergence of the time‐step size and truncation number of wave modes. As the effect of transient wave is taken into account, the numerical results show several transient phenomena involving the vertical pounding, the high pounding force, the multiple‐pounding phenomenon, the vertical separation of girder from the bearing, the dependence of poundings on earthquake period and the narrow period window of poundings. Copyright © 2015 John Wiley & Sons, Ltd.     

Numerical simulations of a highway bridge structure employing passive negative stiffness device for seismic protection

A new passive seismic response control device has been developed, fabricated, and tested by the authors and shown to be capable of producing negative stiffness via a purely mechanical mechanism, thus representing a new generation of seismic protection devices. Although the concept of negative stiffness may appear to be a reversal on the desired relationship between the force and displacement in structures (the desired relationship being that the product of restoring force and displacement is nonnegative), when implemented in parallel with a structure having positive stiffness, the combined system appears to have substantially reduced stiffness while remaining stable. Thus, there is an ‘apparent weakening and softening’ of the structure that results in reduced forces and increased displacements (where the weakening and softening is of a non‐damaging nature in that it occurs in a seismic protection device rather than within the structural framing system). Any excessive displacement response can then be limited by incorporating a damping device in parallel with the negative stiffness device. The combination of negative stiffness and passive damping provides a large degree of control over the expected performance of the structure. In this paper, a numerical study is presented on the performance of a seismically isolated highway bridge model that is subjected to various strong earthquake ground motions. The Negative Stiffness Devices (NSDs) are described along with their hysteretic behavior as obtained from a series of cyclic tests wherein the tests were conducted using a modified design of the NSDs (modified for testing within the bridge model). Using the results from the cyclic tests, numerical simulations of the seismic response of the isolated bridge model were conducted for various configurations (with/without negative stiffness devices and/or viscous dampers). The results demonstrate that the addition of negative stiffness devices reduces the base shear substantially, while the deck displacement is limited to acceptable values. This assessment was conducted as part of a NEES (Network for Earthquake Engineering Simulation) project which included shaking table tests of a quarter‐scale highway bridge model. Copyright © 2014 John Wiley & Sons, Ltd.     

MR阻尼器对斜拉索共振峰频率漂移的影响

本文采用Spencer提出的MR模型,对斜拉索和MR阻尼器组成的系统进行了动力分析,考察了MR阻尼器型号、安装位置、施加的电压以及斜拉索基频(张力、索长、质量)、激励荷载(类型、频率、大小)等各种因素对斜拉索共振峰频率漂移的影响。进而对钱江三桥南岸154m长的斜拉索进行了现场试验。斜拉索自由振动的衰减信号通过阶跃激励的方法获得,经小波变换、Hilbert变换识别出系统的共振峰频率,并与斜拉索在安装油阻尼器和无阻尼器两种情况进行了比较。计算了杭州湾大桥330m长的索在被动控制、半主动控制下的各阶共振峰频率。研究表明,斜拉索在安装MR阻尼器后共振峰频率略微增大。其影响程度比安装油阻尼器时要大。因此MR阻尼器的制振效果除主要来自耗能外,还有部分来自调频作用。     

Effect of variation of normal force on seismic performance of resilient sliding isolation systems in highway bridges

In this study, a series of shaking table tests are carried out on scaled models of two seismically isolated highway bridges to investigate the effect of rocking motion and vertical acceleration on seismic performance of resilient sliding isolators. In addition, performance of RSI is compared with system having solely natural rubber bearings. Test results show that variation of normal force on sliders due to rocking effect and vertical acceleration makes no significant difference in response of RSI systems. In addition, analytical response of prototype isolated bridge and the model used in experiments is obtained analytically by using non‐linear model for isolation systems. It is observed that for seismically isolated bridges, dynamic response of full‐scale complex structures can be predicted with acceptable accuracy by experiments using a simple model of the structure. Copyright © 2005 John Wiley & Sons, Ltd.     

A simulation‐based framework for risk assessment and probabilistic sensitivity analysis of base‐isolated structures

A versatile, simulation‐based framework for risk assessment and probabilistic sensitivity analysis of base‐isolated structures is discussed in this work. A probabilistic foundation is used to address the various sources of uncertainties, either excitation or structural, and to characterize seismic risk. This risk is given, in this stochastic setting, by some statistics of the system response over the adopted probability models and stochastic simulation is implemented for its evaluation. An efficient, sampling‐based approach is also introduced for establishing a probabilistic sensitivity analysis to identify the importance of each of the uncertain model parameters in affecting the overall risk. This framework facilitates use of complex models for the structural system and the excitation. The adopted structural model explicitly addresses nonlinear characteristics of the isolators and of any supplemental dampers, and the effect of seismic pounding of the base to the surrounding retaining walls. An efficient stochastic ground motion model is also discussed for characterizing future near‐fault ground motions and relating them to the seismic hazard for the structural site. An illustrative example is presented that emphasizes the results from the novel probabilistic sensitivity analysis and their dependence on seismic pounding occurrences and on addition of supplemental dampers. Copyright © 2011 John Wiley & Sons, Ltd.     

Relative displacement response spectra with pounding effect

To avoid unseating of a deck, an adequate seat width must be provided. The seat width is basically determined from maximum relative displacement between two bridge segments. Under a strong ground excitation, pounding between two decks may occur at a joint. The pounding will affect the response of two bridge segments. This research is conducted to investigate the effect of pounding on the relative displacement between two adjacent bridge segments. A simplified analytical model of two linear single‐degree‐of‐freedom systems is employed. To take into account the pounding, the laws of conservation of momentum and energy are applied. The analytical results are represented in the form of relative displacement response spectra with pounding effect. It is found that due to the pounding the relative displacement can be amplified, resulting in the requirement of a longer seat width to support a deck. The formulation of normalized relative displacement response spectra is presented together with an application example. It is found that the seat width determined from the relative displacement response spectra with pounding effect becomes close to the value specified in the Japanese design specifications for structures with large difference of natural periods. Copyright © 2001 John Wiley & Sons, Ltd.     

相邻偏心高层建筑物间的振动台碰撞试验

地震引起的相邻建筑物间的碰撞过去多次强烈地震中出现,并造成了较为严重的结构破坏。为研究此问题,设计建造了两座缩尺钢质模型来模拟香港两座相邻的21层建筑,对其进行了一系列振动台碰撞试验,试验结果表明复杂结构间的碰撞可能是周期性的、群周期性的或混沌的,这主要取决于间距、结构参数以及地震动参数。碰撞引起的能量传递可能对较柔较轻的邻近建筑造成较严重的地震反应和破坏。     

A phenomenological contact‐element model considering slight non‐uniform contact for pounding analysis of highway bridges under seismic excitations

Impact stiffness is an important parameter of the contact‐element models for the analysis and prediction of the pounding responses of highway bridges subjected to seismic excitations. This paper presents a pounding experiment to investigate the inconsistencies between the theoretical and experimental values of the impact stiffness both for the linear impact model and Kelvin impact model presented in literature. The analysis of the impact acceleration and acoustic emission signals indicates that accelerometer performance and the non‐uniform pounding are two important factors that affect the pounding responses. Based on this observation, a phenomenological contact‐element model is proposed based on the actual contact state of highway bridges during the impact. To evaluate the effectiveness of the proposed impact model, a numerical simulation is subsequently conducted. A comparison of the results indicates that the proposed impact model can effectively predict the pounding responses of highway bridges. Copyright © 2015 John Wiley & Sons, Ltd.     

地震作用下双薄壁高墩刚构桥桥台处的碰撞效应及减碰措施

针对双薄臂高墩连续刚构桥两侧桥台处主梁与背墙的碰撞现象,基于桥台-背土作用简化模型和Kelvin碰撞模型,采用非线性时程法研究碰撞对双薄臂墩地震剪力、弯矩、曲率和位移,以及支座纵向变形的影响。提出可牺牲背墙、阻尼器、加强型横系梁等三种减碰措施,并对比分析其减碰效果。研究表明:碰撞会显著增大高墩的地震内力和曲率响应,降低墩顶位移和支座的纵向变形;碰撞刚度的变化对碰撞效应的影响在20%以内;可牺牲背墙和阻尼器两种减碰措施均可大幅降低桥墩的地震内力和曲率,使其接近不考虑碰撞时的状态,阻尼器同时还可以保护支座不超过容许变形,而可牺牲背墙则会导致支座的地震破坏;加强型横系梁不能发挥减碰作用,反而会增大桥墩的地震响应。     

Experimental investigation on the seismic response of a steel liquid storage tank equipped with floating roof by shaking table tests

In this paper, the effectiveness of the base isolation on steel storage tanks has been investigated through numerical models and then checked by shaking table tests on a reduced scale (1:14) model of a real steel tank, typically used in petrochemical plants. In the experimental campaign the floating roof has also been taken into account. The tests have been performed on the physical model both in fixed and isolated base configurations; in particular two alternative base isolation systems have been used: high‐damping rubber bearings devices and sliding isolators with elasto‐plastic dampers. Finally, a comparison between experimental and numerical results has also been performed. Copyright © 2009 John Wiley & Sons, Ltd.