The dilatant behaviour of sand–pile interface subjected to loading and stress relief

Property and behaviour of sand–pile interface are crucial to shaft resistance of piles. Dilation or contraction of the interface soil induces change in normal stress, which in turn influences the shear stress mobilised at the interface. Although previous studies have demonstrated this mechanism by laboratory tests and numerical simulations, the interface responses are not analysed systematically in terms of soil state (i.e. density and stress level). The objective of this study is to understand and quantify any increase in normal stress of different pile–soil interfaces when they are subjected to loading and stress relief. Distinct element modelling was carried out. Input parameters and modelling procedure were verified by experimental data from laboratory element tests. Parametric simulations of shearbox tests were conducted under the constant normal stiffness, constant normal load and constant volume boundary conditions. Key parameters including initial normal stress ( $ \sigma_{{{\text{n}}0}}^{\prime } $ ), initial void ratio (e ₀), normal stiffness constraining the interface and loading–unloading stress history were investigated. It is shown that mobilised stress ratio ( $ \tau /\sigma_{\text{n}}^{\prime } $ ) and normal stress increment ( $ \Updelta \sigma_{\text{n}}^{\prime } $ ) on a given interface are governed by $ \sigma_{{{\text{n}}0}}^{\prime } $ and e ₀. An increase in $ \sigma_{{{\text{n}}0}}^{\prime } $ from 100 to 400 kPa leads to a 30 % reduction in $ \Updelta \sigma_{\text{n}}^{\prime } $ . An increase in e ₀ from 0.18 to 0.30 reduces $ \Updelta \sigma_{\text{n}}^{\prime } $ by more than 90 %, and therefore, shaft resistance is much lower for piles in loose sands. A unique relationship between $ \Updelta \sigma_{\text{n}}^{\prime } $ and normal stiffness is established for different soil states. It can be applied to assess the shaft resistance of piles in soils with different densities and subjected to loading and stress relief. Fairly good agreement is obtained between the calculated shaft resistance based on the proposed relationship and the measured results in centrifuge model tests.     

An experimental study of Ti and Zr partitioning among zircon, rutile, and granitic melt

In order to evaluate the effect of trace and minor elements (e.g., P, Y, and the REEs) on the high-temperature solubility of Ti in zircon (zrc), we conducted 31 experiments on a series of synthetic and natural granitic compositions [enriched in TiO₂ and ZrO₂; Al/(Na + K) molar ~1.2] at a pressure of 10 kbar and temperatures of ~1,400 to 1,200 °C. Thirty of the experiments produced zircon-saturated glasses, of which 22 are also saturated in rutile (rt). In seven experiments, quenched glasses coexist with quartz (qtz). SiO₂ contents of the quenched liquids range from 68.5 to 82.3 wt% (volatile free), and water concentrations are 0.4–7.0 wt%. TiO₂ contents of the rutile-saturated quenched melts are positively correlated with run temperature. Glass ZrO₂ concentrations (0.2–1.2 wt%; volatile free) also show a broad positive correlation with run temperature and, at a given T, are strongly correlated with the parameter (Na + K + 2Ca)/(Si·Al) (all in cation fractions). Mole fraction of ZrO₂ in rutile $ \left( {\mathop X\nolimits_{{{\text{ZrO}}_{ 2} }}^{\text{rt}} } \right) $ in the quartz-saturated runs coupled with other 10-kbar qtz-saturated experimental data from the literature (total temperature range of ~1,400 to 675 °C) yields the following temperature-dependent expression: $ {\text{ln}}\left( {\mathop X\nolimits_{{{\text{ZrO}}_{ 2} }}^{\text{rt}} } \right) + {\text{ln}}\left( {a_{{{\text{SiO}}_{2} }} } \right) = 2.638(149) - 9969(190)/T({\text{K}}) $ , where silica activity $ a_{{{\text{SiO}}_{2} }} $ in either the coexisting silica polymorph or a silica-undersaturated melt is referenced to α-quartz at the P and T of each experiment and the best-fit coefficients and their uncertainties (values in parentheses) reflect uncertainties in T and $ \mathop X\nolimits_{{{\text{ZrO}}_{2} }}^{\text{rt}} $ . NanoSIMS measurements of Ti in zircon overgrowths in the experiments yield values of ~100 to 800 ppm; Ti concentrations in zircon are positively correlated with temperature. Coupled with values for $ a_{{{\text{SiO}}_{2} }} $ and $ a_{{{\text{TiO}}_{2} }} $ for each experiment, zircon Ti concentrations (ppm) can be related to temperature over the range of ~1,400 to 1,200 °C by the expression: $ \ln \left( {\text{Ti ppm}} \right)^{\text{zrc}} + \ln \left( {a_{{{\text{SiO}}_{2} }} } \right) - \ln \left( {a_{{{\text{TiO}}_{2} }} } \right) = 13.84\left( {71} \right) - 12590\left( {1124} \right)/T\left( {\text{K}} \right) $ . After accounting for differences in $ a_{{{\text{SiO}}_{2} }} $ and $ a_{{{\text{TiO}}_{2} }} $ , Ti contents of zircon from experiments run with bulk compositions based on the natural granite overlap with the concentrations measured on zircon from experiments using the synthetic bulk compositions. Coupled with data from the literature, this suggests that at T ≥ 1,100 °C, natural levels of minor and trace elements in “granitic” melts do not appear to influence the solubility of Ti in zircon. Whether this is true at magmatic temperatures of crustal hydrous silica-rich liquids (e.g., 800–700 °C) remains to be demonstrated. Finally, measured $ D_{\text{Ti}}^{{{\text{zrc}}/{\text{melt}}}} $ values (calculated on a weight basis) from the experiments presented here are 0.007–0.01, relatively independent of temperature, and broadly consistent with values determined from natural zircon and silica-rich glass pairs.     

The Activity of H2O,Fugacity of O2 and Variation of Their Chemical Potential During Metamorphic Peak of the Granulite Complex Near Taipingzhai—Louzishan Region,East Hebei Province

The thermodynamic calculation of dehydration reacton suggests very low activity of H2O during metamorphic peak of the Archaean granulite complex in the region studied.The αH2O values for Al-rich gneiss and hypersthene biotite gneiss-granulite in the Taipingzhai region are usually between 0.10 and 0.20,and those in the Louzishan region are 0.15-0.25.The fugacity of O2 in terms of lgf O2 in whole region ranges form-8to-14.The average coefficients of (δμH2O/δHMg^Bt)and(δμO2/δXMg^Bt)in the Taipingzhai region are-0.293 and-1.60 respectively,and those in the Louzishan region are-0.364and-1.420.The activity of H2O is very low in the whole region,but its values and other data mentioned above are considerably constant from place to place within a given region,even in rocks of dirrerent lithological characters.However,they show a certain gradient between different regions.Such characteristics are compatible with the genetic mechanism known as“carbonic metamorphism” put forward by Newton et al.,i.e.,the α H2O during the peak stage is controlled by permeation of pervasive CO2 influx of the mantle source,and shows features of external buffering.     

The Hydrolysis of Al(III) in NaCl solutions: A Model for M(II), M(III), and M(IV) Ions

Understanding the identity and stability of the hydrolysis products of metals is required in order to predict their behavior in natural aquatic systems. Despite this need, the hydrolysis constants of many metals are only known over a limited range of temperature and ionic strengths. In this paper, we show that the hydrolysis constants of 31 metals [i.e. Mn(II), Cr(III), U(IV), Pu(IV)] are nearly linearly related to the values for Al(III) over a wide range of temperatures and ionic strengths. These linear correlations allow one to make reasonable estimates for the hydrolysis constants of +2, +3, and +4 metals from 0 to 300°C in dilute solutions and 0 to 100°C to 5 m in NaCl solutions. These correlations in pure water are related to the differences between the free energies of the free ion and complexes being almost equal $$ \Updelta {\text{G}}^\circ \left( {{\text{Al}}^{3 + } } \right) - \Updelta {\text{G}}^\circ \left( {{\text{Al}}\left( {\text{OH}} \right)_{j}^{{\left( {3 - j} \right)}} } \right) \cong \Updelta {\text{G}}^\circ \left( {{\text{M}}^{n + } } \right) - \Updelta {\text{G}}^\circ \left( {{\text{M}}\left( {\text{OH}} \right)_{j}^{{\left( {n - j} \right)}} } \right) $$ The correlation at higher temperatures is a result of a similar relationship between the enthalpies of the free ions and complexes $$ \Updelta {\text{H}}^\circ \left( {{\text{Al}}^{3 + } } \right) - \Updelta {\text{H}}^\circ \left( {{\text{Al}}\left( {\text{OH}} \right)_{j}^{3 - j} } \right) \cong \Updelta {\text{H}}^\circ \left( {{\text{M}}^{n + } } \right) - \Updelta {\text{H}}^\circ \left( {{\text{M}}\left( {\text{OH}} \right)_{j}^{n - j} } \right) $$ The correlations at higher ionic strengths are the result of the ratio of the activity coefficients for Al(III) being almost equal to that of the metal. $$ \gamma \left( {{\text{M}}^{n + } } \right)/\gamma \left( {{\text{M}}\left( {\text{OH}} \right)_{j}^{n - j} } \right) \cong \gamma \left( {{\text{Al}}^{3 + } } \right)/\gamma \left( {{\text{Al}}\left( {\text{OH}} \right)_{j}^{3 - j} } \right) $$ The results of this study should be useful in examining the speciation of metals as a function of pH in natural waters (e.g. hydrothermal fresh waters and NaCl brines).     

A multi-isotope approach for understanding sources of water,carbon and sulfur in natural springs of the Central Appalachian region

Natural springs have been reliable sources of domestic water and have allowed for the development of recreational facilities and resorts in the Central Appalachians. The structural history of this area is complex and it is unknown whether these natural springs receive significant recharge from modern precipitation or whether they discharge old water recharged over geological times scales. The main objective of this study was to use stable isotopes of water ( $\delta^{18} {\text{O}}_{{{\text{H}}_{2} {\text{O}}}}$ and $\delta^{2} {\text{H}}_{{{\text{H}}_{2} {\text{O}}}}$ ), dissolved inorganic carbon ( $\delta^{13} {\text{C}}_{\text{DIC}}$ ) and dissolved sulfate ( $\delta^{34} {\text{S}}_{{{\text{SO}}_{4} }}$ and $\delta^{18} {\text{O}}_{{{\text{SO}}_{4} }}$ ) to delineate sources of water, carbon and sulfur in several natural springs of the region. Our preliminary isotope data indicate that all springs are being recharged by modern precipitation. The oxygen isotope composition indicates that waters in thermal springs did not encounter the high temperatures required for O isotope exchange between the water and silicate/carbonate minerals, and/or the residence time of water in the aquifers was short due to high flow rates. The carbon isotopic composition of dissolved inorganic carbon and sulfur/oxygen isotopic composition of dissolved sulfate provide evidence of low-temperature water–rock interactions and various biogeochemical transformations these waters have undergone along their flow path.     

Biradical states of oxygen-vacancy defects in ��-quartz: centers E_{2}^{\prime \prime } and E_{4}^{\prime \prime }

Several new radiation defects with total electron spin S?=?1 occurring in electron-irradiated, synthetic ??-quartz have been observed by using electron paramagnetic resonance spectroscopy. These defects are considered to be biradicals, i.e., pairs of S?=?1/2 species. The concentration of these centers depends on the condition of the fast-electron irradiation. They have different decay behaviors that allow measurements of any individual species especially when it predominates over the others. The primary spin Hamiltonian parameter matrices g ₁, g ₂, D have now been determined for two similar defects, which herein are labeled $ E_{2}^{\prime \prime } $ and $ E_{4}^{\prime \prime } $ . Inter-electron distances estimated by using the magnetic dipole model, suggest that the structures of centers $ E_{2}^{\prime \prime } $ and $ E_{4}^{\prime \prime } $ both involve the unpaired electrons each located in orbitals of two silicon atoms next to a common oxygen vacancy but which have slightly different Si?CSi distances at 0.90 and 0.79?nm, respectively. This model is consistent with previous DFT calculations of the triplet configurations with local energetic minima. Observed decay behaviors suggest a transformation of centers $ E_{2,4}^{\prime \prime } $ to the analogous $ E_{1}^{\prime \prime } $ center. These triplet centers in quartz provide new insights into the structures of analogous defects in amorphous silica.     

Estimating the Density and Compressibility of Seawater to High Temperatures Using the Pitzer Equations

The density and compressibility of seawater solutions from 0 to 95 °C have been examined using the Pitzer equations. The apparent molal volumes (X = V) and compressibilities (X = κ) are in the form $$ X_{\phi } = \bar{X}^{0} + A_{X} I/(1.2 \, m)\ln (1 + 1.2 \, I^{0.5} ) + \, 2{\text{RT }}m \, (\beta^{(0)X} + \beta^{(1)X} g(y) + C^{X} m) $$ where $ \bar{X}^{0} $ is the partial molal volume or compressibility, I is the ionic strength, m is the molality of sea salt, A_X is the Debye–Hückel slope for volume (X = V) or adiabatic compressibility (X = κ _s), and g(y) = (2/y ²)[1 ? (1 + y) exp(?y)] where y = 2I ^0.5. The values of the partial molal volume and compressibility ( $ \bar{X}^{0} $ ) and Pitzer parameters (β ^(0)X , β ^(1)X and C ^X ) are functions of temperature in the form $$ Y^{X} = \sum_{i} a_{i} (T-T_{\text{R}} )^{i} $$ where a _i are adjustable parameters, T is the absolute temperature in Kelvin, and T _R = 298.15 K is the reference temperature. The standard errors of the seawater fits for the specific volumes and adiabatic compressibilities are 5.35E?06 cm³ g^?1 and 1.0E?09 bar^?1, respectively. These equations can be combined with similar equations for the osmotic coefficient, enthalpy and heat capacity to define the thermodynamic properties of sea salt to high temperatures at one atm. The Pitzer equations for the major components of seawater have been used to estimate the density and compressibility of seawater to 95 °C. The results are in reasonable agreement with the measured values (0.010E?03 g cm^?3 for density and 0.050E?06 bar^?1 for compressibility) from 0 to 80 °C and salinities from 0 to 45 g kg^?1. The results make it possible to estimate the density and compressibility of all natural waters of known composition over a wide range of temperature and salinity.     

Redox-controlled iron isotope fractionation during magmatic differentiation: an example from the Red Hill intrusion, S. Tasmania

This study presents accurate and precise iron isotopic data for 16 co-magmatic rocks and 6 pyroxene–magnetite pairs from the classic, tholeiitic Red Hill sill in southern Tasmania. The intrusion exhibits a vertical continuum of compositions created by in situ fractional crystallisation of a single injection of magma in a closed igneous system and, as such, constitutes a natural laboratory amenable to determining the causes of Fe isotope fractionation in magmatic rocks. Early fractionation of pyroxenes and plagioclase, under conditions closed to oxygen exchange, gives rise to an iron enrichment trend and an increase in $ f_{{{\text{O}}_{2} }} $ of the melt relative to the Fayalite–Magnetite–Quartz (FMQ) buffer. Enrichment in Fe³⁺/ΣFe_melt is mirrored by δ⁵⁷Fe, where ^VIFe²⁺-bearing pyroxenes partition ⁵⁷Fe-depleted iron, defining an equilibrium pyroxene-melt fractionation factor of $ \Updelta^{57} {\text{Fe}}_{{{\text{px}} - {\text{melt}}}} \le - 0.25\,\permille \times 10^{6} /T^{2} $ . Upon magnetite saturation, the $ f_{{{\text{O}}_{2} }} $ and δ⁵⁷Fe of the melt fall, commensurate with the sequestration of the oxidised, ⁵⁷Fe-enriched iron into magnetite, quantified as $ \Updelta^{57} {\text{Fe}}_{{{\text{mtn}} - {\text{melt}}}} = + 0.20\,\permille \times 10^{6} /T^{2} $ . Pyroxene–magnetite pairs reveal an equilibrium fractionation factor of $ \Updelta^{57} {\text{Fe}}_{{{\text{mtn}} - {\text{px}}}} \approx + 0.30\,\permille $ at 900–1,000?°C. Iron isotopes in differentiated magmas suggest that they may act as an indicator of their oxidation state and tectonic setting.     

Crystallographic preferred orientation in wüstite (FeO) through the cubic-to-rhombohedral phase transition

Magnesiowüstite, (Mg_0.08Fe_0.88)O, and wüstite, Fe_0.94O, were compressed to ~36?GPa at ambient temperature in the diamond anvil cell (DAC) at the Advanced Light Source. X-ray diffraction patterns were taken in situ in radial geometry in order to study the evolution of crystallographic preferred orientation through the cubic-to-rhombohedral phase transition. Under uniaxial stress in the DAC, {100}_c planes aligned perpendicular to the compression direction. The {100}_c in cubic became { $\left\{ {10\bar 14} \right\}$ }_r in rhombohedral and remained aligned perpendicular to the compression direction. However, the {101}_c and {111}_c planes in the cubic phase split into { ${10{\bar{1}}4}$ }_r and { ${11{\bar{2}}0}$ }_r, and (0001)_r and { ${10{\bar{1}}1}$ }_r, respectively, in the rhombohedral phase. The { ${11{\bar{2}}0}$ }_r planes preferentially aligned perpendicular to the compression direction while { ${10{\bar{1}}4}$ }_r oriented at a low angle to the compression direction. Similarly, { ${10{\bar{1}}1}$ }_r showed a slight preference to align more closely perpendicular to the compression direction than (0001)_r. This variant selection may occur because the 〈 ${10{\bar{1}}4}$ 〉_r and [0001]_r directions are the softer of the two sets of directions. The rhombohedral texture distortion may also be due to subsequent deformation. Indeed, polycrystal plasticity simulations indicate that for preferred { ${10{\bar{1}}4}$ }〈 ${1{\bar{2}}10}$ 〉_r and { ${11{\bar{2}}0}$ }〈 ${{\bar{1}}101}$ 〉_r slip and slightly less active { ${10{\bar{1}}1}$ }〈 ${{\bar{1}}2{\bar{1}}0}$ 〉_r slip, the observed texture pattern can be obtained.     

The origin of mafic rocks in the Naqadeh intrusive complex, Sanandaj-Sirjan Zone, NW Iran

The Naqadeh mafic plutonic rocks are located on a plutonic assemblage and include different granitoid rocks related to ～40 Ma. U-Pb SHRIMP data shows different ages of 96?±?2.3 Ma for mafic rocks. Naqadeh mafic plutonic rocks consist of diorite to diorite-gabbros with relatively high contents of incompatible elements, low Na2O, and $ {\hbox{Mg\# }} = \left[ {{\hbox{molar}}\;{100} \times {\hbox{MgO/}}\left( {{\hbox{MgO}} + {\hbox{FeO}}} \right)} \right] > 44.0 $ . These features suggest that the Naqadeh mafic rocks originate from enriched lithospheric mantle above subducted slab during Neotethys subduction under Iranian plate.     

Multiple-pumped-well aquifer test to determine the anisotropic properties of a karst limestone aquifer in Pasco County, Florida, USA

Groundwater-level data from an aquifer test utilizing four pumped wells conducted in the South Pasco wellfield in Pasco County, Florida, USA, were analyzed to determine the anisotropic transmissivity tensor, storativity, and leakance in the vicinity of the wellfield. A weighted least-squares procedure was used to analyze drawdowns measured at eight observation wells, and it was determined that the major axis of transmissivity extends approximately from north to south and the minor axis extends approximately from west to east with an angle of anisotropy equal to N4.54°W. The transmissivity along the major axis ${\left( {T_{{\xi \xi }} } \right)}$ is 14,019 m² day^–1, and the transmissivity along the minor axis ${\left( {T_{{\eta \eta }} } \right)}$ is 4,303 m² day^–1. The equivalent transmissivity $T_{e} = {\left( {T_{{\xi \xi }} T_{{\eta \eta }} } \right)}^{{1 \mathord{\left/ {\vphantom {1 2}} \right. \kern-0em} 2}} = 7,767{{\text{m}}^{2} } \mathord{\left/ {\vphantom {{{\text{m}}^{2} } {{\text{day}}^{{ - {\text{1}}}} }}} \right. \kern-0em} {{\text{day}}^{{ - {\text{1}}}} }$ , and the ratio of anisotropy is 3.26. The storativity of the aquifer is 7.52?×?10^?4, and the leakance of the overlying confining unit is 1.37?×?10^?4 day^?1. The anisotropic properties determined for the South Pasco wellfield in this investigation confirm the results of previous aquifer tests conducted in the wellfield and help to quantify the NW–SE to NE–SW trends for regional fracture patterns and inferred solution-enhanced flow zones in west-central Florida.     

Adsorption kinetics of chromium(III) removal from aqueous solutions using natural red earth

Laboratory-scale-simulated experiments were carried out using Cr(III) solutions to identify the Cr(III) retention behavior of natural red earth (NRE), a natural soil available in the northwestern coastal belt of Sri Lanka. The effects of solution pH, initial Cr(III) concentration and the contact time were examined. The NRE showed almost 100 % Cr(III) adsorption within the first 90 min. [initial [Cr(III)] = 0.0092–0.192 mM; initial pH 4.0–9.0]. At pH 2 (298 K), when particle size ranged from 125 to 180 μm the Cr(III) adsorption data were modeled according to Langmuir convention assuming site homogeneity. The pH-dependent Cr(III) adsorption data were quantified by diffused layer model assuming following reaction stoichiometries: $$ \begin{aligned} 2\, {>}{\text{AlOH}}_{{({\text{s}})}} + {\text{ Cr }}\left( {\text{OH}} \right)_{{ 2\,({\text{aq}})}}^{ + } \, \to \, \left( { {>}{\text{AlO}}} \right)_{ 2} {\text{Cr}}_{{({\text{s}})}}^{ + } + {\text{ 2H}}_{ 2} {\text{O}} \quad {\text{log K 15}}. 5 6\\ 2\, {>}{\text{FeOH}}_{{({\text{s}})}} + {\text{ Cr}}\left( {\text{OH}} \right)_{{ 2\,({\text{aq}})}}^{ + } \, \to \, \left( { {>}{\text{FeO}}} \right)_{ 2} {\text{Cr}}_{{({\text{s}})}}^{ + } + {\text{ 2H}}_{ 2} {\text{O}}\quad {\text{log K 5}}.0 8.\\ \end{aligned} $$ The present data showed that NRE can effectively be used to mitigate Cr(III) from aqueous solutions and this method is found to be simple, effective, economical and environmentally benign.