浙西饱和红黏土的物理力学特性试验研究

本文在分析浙西红黏土矿物成分与化学成分的基础上,分别用单向固结仪和三轴仪对饱和红黏土原状样进行了一系列的压缩、剪切、蠕变试验,得到其压缩曲线、应力-应变曲线和蠕变曲线。根据测得的压缩曲线,确定了该土的压缩指数Cc、回弹指数Cs,对原状样压缩曲线的归一化整理后判断出原状饱和红黏土的结构性不强;根据三轴排水剪切试验结果,得出原状饱和红黏土在不同围压下因结构性的存在土体具有不同的破坏应力比,计算得到该土的临界状态应力比和黏聚力;根据原状饱和红黏土在不同固结压力下的蠕变试验结果,得到了该土的次固结系数Cα与固结压力关系,并确定了该土的Cα/Cc约为0.0124,本试验结果为浙西地区的工程建设提供了基本参数。     

广西靖西红粘土的变形和强度特性研究

对广西靖西取得的3种红粘土原状土样以及室内制备的重塑土样进行单轴压缩试验和三轴剪切试验（包括浸水饱和后的试验）,其目的是研究静力荷载作用下红粘土的固结变形和强度特征。研究表明,在较大的压缩应力作用下,土样仍有较大的孔隙比;红粘土的破坏面为一个曲面变化形态,试样首先沿较为软弱的不规则面发生,然后才形成贯通的滑动面;尽管土样在破坏时出现明显的剪切破坏面（表现为一定的脆性破坏特征）,但其应力应变关系呈现应变硬化的特点,表明红粘土有很强的粘滞特性。     

红黏土浸水变形特性试验研究

对广西桂林红黏土进行了浸水饱和引起的膨胀变形和压缩变形试验,在竖向压力25~800 k Pa范围下,研究了不同初始含水率和干密度对浸水变形特性的影响。结果表明:浸水饱和引起的压缩变形量主要取决于初始干密度,而初始含水率对其影响较小;在相同的含水率下,浸水压缩变形量随着干密度的增加而减小。把各组的固结状态线和浸水饱和稳定后状态线的交点称为分界点。初始含水率对分界点的影响较小,而随着干密度的增加,分界点右移,即浸水膨胀区域增大,浸水压缩区域减小。由分界点可得出了介于浸水膨胀和浸水压缩的分界状态线,从而可以判定不同孔隙比、不同竖向压力下土样会产生浸水膨胀还是压缩。最后,基于浸水变形试验结果,可以计算压缩区红黏土试样在不同竖向压力下浸水压缩变形量。     

饱和膨润土及其与砂混合物的压缩变形特性

对用不同制样方法得到的饱和膨润土及其与砂混合物进行了压缩试验。试验结果表明,饱和膨润土的压缩曲线呈双线性,不同于普通黏土的压缩曲线。压缩试验中量测了侧向应力,由此得到的饱和膨润土的静止侧向压力系数值较一般黏土的数值要大。对膨润土与砂混合物的击实样进行了由非饱和到饱和状态的浸水试验,并得出试验过程中侧向应力的变化规律。由于浸水饱和的试样和抽真空饱和的试样在较高压力时压缩曲线趋于一致,可采用快速抽真空饱和的方法进行试验研究,以缩短非饱和混合物击实样浸水饱和所需时间。引入骨架孔隙比的概念,用来判断膨润土与砂混合物中砂骨架是否形成,得出影响混合物压缩特性的决定因素。     

赤泥的变形-强度特性与结构性关系的研究

制铝工业排出的大量固体废料?--赤泥具有较强的结构性,笔者对其结构性及变形–强度特性进行了研究。根据饱和原状赤泥样及扰动样固结排水三轴剪切试验资料,用土力学方法分析了变形–强度特性与结构性之间的关系,探讨了结构性参数随轴应变及固结压力变化的规律。研究表明：（1）对浸水反应比较迟钝的饱和赤泥,用三轴试验条件下各应变水平原状样与扰动样的主应力差之比所表示的结构性定量化参数,来研究结构性对变形强度的影响可以得到良好的规律性。（2）结构性参数对固结周围应力反应敏感,不同固结周围压力和剪切应力对结构性的影响,主要发生在低应变区段内。(3)赤泥的变形–强度特性与其在形成过程中的固结应力大小及龄期长短没有直接的规律性关系,而与其在物理化学作用下结构性的强弱相关。     

不同温度应力路径下饱和黏土剪切特性

在精准温控动三轴试验系统上开展了不同温度及不同升温路径饱和黏土剪切试验研究,探讨了不同温度对饱和软黏土不排水剪切特性的影响,分析不同升温固结方式对饱和软黏土孔压发展、体变、强度以及模量的影响规律。试验结果显示：在4～76 ℃试验研究范围内,环境温度升高导致饱和软黏土的不排水剪切强度有所减少,但温度升高对土体模量增加影响明显,温度T和模量ET关系可用ET = 2.69T 0.3表达;升温变化时正常固结黏土产生超孔隙水压力并随着温度增大而增大,升温热固结后土的剪切强度将明显提高,且排水状态下升温固结对土剪切强度增长小于升温完成后再固结情况;土体从26 ℃分别升高20、40 ℃时,升温引起的超孔压比分别为0.41、0.61,剪切峰值强度分别增加8.23%、22.37%。研究表明：升温幅值增大会使土体热固结程度越大,升温分级越多,热固结也越充分,其对应的体变、强度增长率则越大;同时最终温度及热固结路径对其剪切相转换特征存在影响,升温越高、热固结路径越多其剪胀性越明显,但温度变化范围、固结分级、热固结路径总体上对孔隙水压力的发展基本不产生影响。     

钱塘江冲海积粉土剪胀性三轴试验研究

钱塘江两岸广泛分布着冲海积粉土.通过大量的三轴固结不排水CU和固结排水CD试验,探讨饱和粉土的应力应变性状和剪胀特性。试验表明,钱塘江冲海积粉土显著的特性之一是在剪切中膨胀,剪胀主要与粉土的密度和围压有关。CU试验中密(e=0.739～0.866)的原状样在围压600kPa范围内剪切膨胀,稍密(e=0.890～0.906)的击实样在围压低于400kPa剪切膨胀。由于粉土膨胀的本质不排水强度在剪切中保持增加,对于这种情况就没有惟一的"不排水强度";CD试验稍密(e=0.889～0.945)的击实样在围压低于400kPa时剪切膨胀。钱塘江冲海积粉土的剪切破坏要经历一个大的变形过程,固结排水剪切过程的应力应变性状可分为4个阶段。取应变继续而没有进一步体积变化的临界状态做破坏标准,确定粉土排水剪切强度指标较合理。     

采用环剪仪对超固结黏土抗剪强度特性的研究

利用大型高速环剪仪,对不同超固结比、法向应力和剪切速率下的超固结饱和黏土的峰值强度和残余强度特性进行了研究,并对循环荷载作用前后残余强度的变化进行了初步探讨。试验结果表明,（1）超固结比对超固结黏土的峰值强度和残余强度有着明显的影响;（2）在剪切速率相同的条件下,土体达到残余强度时的位移取决于现存的应力状态,而与应力历史无关;（3）剪切速率越大,峰值强度随之增大,达到稳定残余强度时的剪切位移也随之增加,但剪切速率的变化对残余强度值几乎没有影响;（4）在循环荷载作用下残余强度不同程度的降低,最大降低幅度达12.2 %;当土体剪切面为不规则剪切带时,施加循环荷载后出现残余强度上升的现象。     

不同应力路径下饱和黏土耦合循环剪切特性

地基土单元体在波浪荷载的作用下将发生主应力轴连续旋转,这对土的强度和变形特性会产生显著的影响。针对饱和黏土,利用土工静力－动力液压三轴－扭转多功能扭剪仪进行了均等固结下的耦合循环剪切试验,着重研究了不同循环应力路径对应力-应变关系和强度特性的影响。试验结果表明,耦合循环荷载下黏土扭转剪切分量和正向偏差分量的应力-应变关系曲线与应力路径有关,且随着振动次数的增加逐渐疏松,割线模量 和 不断衰减,这与不固结不排水条件下的应力-应变关系曲线的变化规律明显不同;扭转剪切分量大的椭圆应力路径的动强度略小于正向偏差分量大的动强度。饱和黏土在不同应力路径下的力学特性的试验研究可以为建立复杂应力路径下的本构模型提供试验依据。     

纳米碳酸钙影响下红黏土强度特性试验研究

为了探寻纳米碳酸钙对桂林红黏土力学强度特性的影响机理,利用TSZ-1型三轴试验仪进行不固结不排水三轴压缩试验,分析了在不同干密度条件下各梯度纳米碳酸钙掺量对重塑红黏土黏聚力、内摩擦角、抗剪强度以及应力-应变曲线的影响,从红黏土矿物颗粒胶体化学的角度阐释纳米碳酸钙对红黏土力学强度的影响机理,研究结果表明:随着纳米碳酸钙掺量增加,红黏土黏聚力、内摩擦角以及抗剪强度呈现先减小后增大的趋势;纳米碳酸钙的掺入改变了原有的介质电荷pH值,使得红黏土原有的氧化铁胶结吸附平衡发生改变,形成新的钙质胶结团粒,改变了红黏土的强度特性;加入纳米碳酸钙后起始干密度为1.4g ·cm-3的重塑红黏土样应力-应变曲线由弹性理想塑性型变为应变硬化型。     

Shear strength of a compacted scaly clay in variable saturation conditions

Scaly clays are stiff and highly fissured clays often used as construction materials. This paper presents the results of triaxial compression tests carried out on saturated and unsaturated samples of a compacted scaly clay. Complementary investigation on the microstructural features and their evolution with the amount of water stored into the material are also presented in order to shed light on the evolution of the micro- and macroporosity with suction. The water retention behaviour of the compacted scaly clay is also addressed. The results from the controlled suction triaxial tests are used to discuss the applicability of a single-shear strength criterion to compacted double-structured clays when the effective stress concept for unsaturated soils is used. The choice of the degree of saturation to be included in the effective stress definition for obtaining a satisfactory representation of the shear strength is addressed. It is shown that the best results are obtained when the macropore degree of saturation is considered along with its evolution during the applied stress path.     

南阳膨胀土的工程地质特征和填筑适宜性

施工阶段的工程地质调查发现,宁（南京）西（西安）铁路内乡-镇平段南阳膨胀土成因类型上不仅有第四系冲积洪积粘土,而且发育上第三系湖相沉积粘土。不同成因的膨胀土具有不同的空间分布特征和工程性质,X射线衍射测试表明,南阳膨胀土的主要膨胀性粘土矿物是伊利石/蒙脱石混层矿物。物质组成和物理化学性质差异导致击实土在含水量变化条件下膨胀力和膨胀变形有明显的差别;对同一种膨胀土材料,其击实含水量越小,膨胀性越强,甚至含水量降低1 %～2 %,膨胀力就可以增加到200 %以上;击实膨胀土的直剪强度受到钙质结核含量的影响,对于膨胀势为高或强的膨胀土,结核含量小于15 % 时,经过干湿循环后直剪强度衰减量为40 %～65 %,结核含量为25 %～30 % 的强膨胀土直剪强度衰减量则低于30 %;对膨胀土的地质特征、工程性质、击实土的膨胀性和直剪试验结果进行分析,探讨其用于填筑铁路路基的适宜性,进行了填筑适宜性分级。依据研究成果制定的路基施工工艺取得了比较理想的工程效果     

Three‐dimensional elasto‐plastic model for unsaturated compacted soils with different initial densities

This paper presents an elasto‐plastic model for unsaturated compacted soils and experimental results obtained from a series of suction‐controlled triaxial tests on unsaturated compacted clay with different initial densities. The initial density dependency of the compacted soil behaviour is modelled by establishing experimental relationships between the initial density and the corresponding yield stress and thereby between the initial density and the location and slope of normal compression line. The model is generalized to three‐dimensional stress states by assuming that the shapes of the failure surface and the yield surface in the deviatoric plane are given by the extended SMP criterion. A considerable number of the isotropic compression, triaxial compression and extension tests on unsaturated compacted clay with different initial densities were performed using a suction‐controllable triaxial apparatus, to measure the stress–strain–volume change in different stress paths and wetting paths. The model has well‐predicting capabilities to reproduce the mechanical behaviour of specimens compacted under different conditions not only in isotropic compression but also in triaxial compression and triaxial extension. Copyright © 2003 John Wiley & Sons, Ltd.     

荆门非饱和膨胀土的变形与强度特性试验研究

通过压力板试验,对比分析了荆门原状膨胀土与石灰改良土持水特征的差异性;应用非饱和土三轴仪,开展了原状膨胀土、石灰改良膨胀土与重塑膨胀土的变形及强度特性试验。结果表明：①石灰改良膨胀土与原状膨胀土相比,其进气值有显著降低,残余含水率显著升高,土-水特征曲线两个特征点的斜率较为平缓,说明其水稳定性较好,土体性状更为稳定;②原状膨胀土和石灰改良膨胀土在非饱和与饱和状态的应力-应变关系曲线均呈应变软化型,随净围压的增大,应变软化的程度趋缓;随含水率的减小,峰值应力增大,应力峰值点有所提前,应变软化现象更加显著。饱和重塑膨胀土的应力-应变关系呈应变强化型,非饱和重塑膨胀土则呈现为应变软化型,但其应变软化的程度较前两类土大为趋缓;③经石灰改性后,膨胀土强度参数值有大幅度提高,即使在湿化饱和后,石灰改良膨胀土仍保持了相对稳定的力学性质和较高的抗剪强度参数值。相比之下,无论是重塑膨胀土,还是原状膨胀土,对湿化作用均十分敏感,其强度参数值或波动较大,或整体水平较低。     

Strength Anisotropy of Compacted Decomposed Granite Soils

In order to investigate the strength and deformation anisotropy of compacted decomposed granite soils, a series of drained triaxial compression tests was performed on unsaturated and saturated decomposed granite soils. The specimens were subjected to compression tests such that the angle δ of the direction of the major principal stress, σ ₁, during triaxial compression relative to the compaction plane (bedding plane) varies, with δ = 0°, 45° and 90°. Test results indicated that the compressive strain of the specimens subjected to isotropic consolidation was influenced strongly by the angle δ. In addition, the effect of the angle δ on the triaxial compressive strength and deformation was more evident in unsaturated specimens than in saturated specimens. Based on the test results, a procedure which can be used to estimate the shear strength of unsaturated soils taking into account various angles δ was proposed.     

水泥加固红土的受力特性及其微结构特征

水泥加固红土的击实、剪切、压缩和渗透等受力特性及其微结构特征受到水泥加入比例和试样养护时间的影响。研究结果表明,水泥加固红土存在最佳击实制样时间,水泥加入越多,最大干密度越大、最优含水率越小。其抗剪强度和抗剪强度指标随水泥加入比例的增加和试样养护时间的延长逐渐增大,但增大的程度逐渐减慢,对粘聚力的影响大于对内摩擦角的影响;其压缩性和渗透性随水泥加入比例的增加和试样养护时间的延长显著减小,但减小的程度逐渐变缓;水泥加入比例的影响大于试样养护时间的影响。实质上,水泥的加入和试样的养护导致水泥加固红土呈现出包裹、填充和胶结的微结构特征,引起水泥加固红土的击实、剪切、压缩和渗透等力学特性的宏观变化。     

Shear Strength Behavior of Two Landfill Clay Liners

Direct shear tests were conducted to obtain both the shear strength of compacted clay liners (CCLs) specimens and the interface shear strength between compacted clay liner and base soil. These experiments were conducted under the conditions of five different water contents. The experimental results show that shear strength of both CCLs and CCLs/base interface decreases with the increase in the water content of CCLs and base soil. In addition, the considerate concentration of NaCl in leachate has no deteriorating effect on the shear strength of liners. Triaxial shear tests were also conducted on clay liner specimens to obtain total and effective shear strength under a fast compression. The shear strength c‘=100 kPa for sand-bentonite, respectively. These results indicate that the compacted clay-bentonite shows normal consolidation, but that the compacted sand-bentonite exhibits over-consolidation.     

Yielding of Silt at High Temperature and Suction Magnitudes

This study presents an evaluation of yielding mechanisms for unsaturated, compacted silt using drained triaxial compression tests with control of elevated temperatures and high suction magnitudes. After anisotropic compression, some compacted silt specimens were heated by approximately 40 °C before a suction of approximately 300 MPa was applied, while others were heated after suction application. A frictional response was observed for the specimens sheared under high suction magnitudes, in the form of a consistent increase in peak shear strength with increasing net confining stress. An effective stress analysis was used to evaluate the trends in the peak shear stress and the role of stress history for the different specimens. A single peak failure envelope was observed when the shear strength data was interpreted in terms of the mean effective stress. Changes in preconsolidation stress were estimated by identifying the intersections between a thermo-elasto-plastic yield function and the experimental peak shear strength values. Soil specimens heated before application of high suction values had lower peak shear strengths than reference specimens at high suction and ambient temperature. This behaviour is consistent with thermal softening trends observed in soils heated under low suction values. However, soil specimens heated after suction application had greater peak shear strengths than the reference specimens. This indicates heating under high suction results in hardening. The impact of suction on the preconsolidation stress was found to be better represented by a power law model at high suction magnitudes than other available models. The estimated preconsolidation stress values were used to evaluate the impacts of stress history on the thermal volume change response, which matched well with data from tests on saturated specimens.