Evaluation of hydraulic conductivity through particle shape and packing density characteristics of sand–silt mixtures

Abstract

This study aims to evaluate the relationship between saturated hydraulic conductivity with particle shape and packing density characteristics of silty sand soils. The article presents a series of hydraulics tests performed on three kinds of sand with different particles shapes (Chlef rounded sand, Fontainebleau sub-rounded sand and Hostun sub-angular sand) mixed with low plastic rounded Chlef silt in the range of 0–30% fines content. The sand–silt mixture samples were tested in the constant-head permeability device at a loose relative density (D_r = 18%) and a constant room temperature (T?=?20?°C). The obtained results indicate that the measured saturated hydraulic conductivity (K_s) correlates very well with the fines content (F_c), packing density in terms of [maximum void ratio “e_max,” minimum void ratio “e_min,” predicted maximum void ratio “e_max”_pr and predicted minimum void ratio “e_min”_pr] and particle shape characteristics ratios in terms of roundness ratio (R_r = R_hs/R_mixture) and sphericity ratio (S_r = S_hs/S_mixture) of the silty sand materials under consideration. Moreover, the analysis of the available data show a noticeable success in exploring the prediction of the saturated hydraulic conductivity (K_s) based on the particle shape and packing density characteristics (R_r, S_r, e_max, and e_min) of the studied sand–silt mixture samples.     

Behavior of Loose Silty Sand of Chlef River: Effect of Low Plastic Fine Contents and Other Parameters

This article presents a laboratory study of static behavior of silty-sand soils. The objective of this laboratory investigation is to study the effect of initial confining pressures and fines content on the undrained shear strength (known as liquefaction resistance) response, pore pressure, and hydraulic conductivity of sand–silt mixtures. The triaxial tests were conducted on reconstituted saturated silty-sand samples at initial relative density D_r = 15% with fines content ranging from 0 to 50%. All the samples were subjected to a range of initial confining pressures (50, 100, and 200 kPa). The obtained results indicate that the presence of low plastic fines in sand–silt mixture leads to a more compressible soil fabric, and consequently to a significant loss in the soil resistance to liquefaction. The evaluation of the data indicates that the undrained shear strength can be correlated to fines content (F_c), inter-granular void ratio (e_g), and excess of pore pressure (Δu). The undrained shear strength decreases with the decrease of saturated hydraulic conductivity and the increase of fines content for all confining pressures under consideration. There is a relatively high degree of correlation between the peak shear strength (q_peak) and the logarithm of the saturated hydraulic conductivity (k_sat) for all confining pressures.     

Study of dilatancy behaviors of calcareous soils in a triaxial test

Abstract

In this article, the dilatancy of calcareous soil is studied systematically based on triaxial consolidation drainage shear tests, and the difference in dilatancy between calcareous soil and siliceous soil is also investigated. It was found that: ① Calcareous soil experience obvious dilated deformation. Dilatancy tendency increases with increasing related density and decreases with increasing confining pressure. ② The volumetric strain rate initially increases from negative to positive. After it reaches a maximum, there is a small decrease in the volumetric strain rate, but it is still greater than zero, and the stress-strain curves are of softening type. ③ For the same condition, the dilatancy deformation of calcareous sand begins later than that of siliceous sand, and the volume compression before dilatancy is also larger for calcareous sand. ④ The critical state alone cannot accurately describe the entire deformation process of soil, and it is proposed that the phase transformation state be added to the standard method used to assess soil dilatation and contraction. ⑤ Based on the statistical analysis of experimental data, mathematical relationships were established between void ratio, relative density, and effective confining pressure of phase transformation state and critical state, respectively.

• Highlights

• Reports results from a well-designed experiment that includes a good amount of samples and data.

• Effects of relative density and effective confining pressure on deformation mode and mechanical properties of calcareous sand are evaluated.

• The difference in dilatancy between calcareous sand and siliceous sand was compared

• The phase-transformation state and critical state were compared with the axial strain, volumetric strain and deviatoric stress.

• Using phase-transformation void ratio and critical void ratio to describe the whole deformation process of calcareous sand is proposed.

• The mathematical expressions of phase-transformation void ratio and critical void ration were given, respectively.

     

海洋含黏粒砂土共振柱试验研究

本文利用英国GDS公司生产的RCA共振柱系统测试海洋含黏粒砂土动剪切模量,同时对比纯砂样的动剪切模量,系统研究固结应力、初始密实度、黏粒含量等因素对砂土最大动剪切模量的影响。试验结果表明:最大动剪切模量随有效固结应力增大而增大;随初始密实度增大而增大;随黏粒含量的增加而降低。     

Equivalent void ratio controlling the mechanical properties of cementitious material-clay mixtures with high water content

Abstract

This research develops a parameter defined as the equivalent void ratio, e?_st, which is able to accurately describe the dependence of the mechanical properties of cementitious material-clay mixtures on the influencing parameters, i.e., the mixing proportion, curing time, and initial state of the mixture, for different types of cementitious materials based on the results of unconfined compression, oedometer, and triaxial tests. Besides Portland cement, cementitious materials, such as fly ash and rice husk ash, are considered supplementary cement with different levels of efficiency. This equivalent cementitious material concept is then adapted for parameter development in conjunction with the effective void ratio proposed from our previous study. The developed single parameter, e?_st, can assess the mechanical properties of cementitious material-clay mixtures with different types of cementitious materials and under different test conditions.     

Evaluation of cyclic shear strength of mixtures with sand and different types of fines

Soils are classified as sandy soils and clayey soils in most soil classification systems, and appropriate equations are used for practical design, depending on soil type, to represent each soil behavior. Sand-clay mixtures, however, need a special standard to evaluate their specific behaviors since they are categorized as intermediate soils or transitional soils and typically show intermediate properties. In this article, a series of cyclic triaxial tests were conducted on specific sand-fines mixtures with three fine types and various fine contents. The behaviors of various soil mixtures (silica sand with Iwakuni natural clay, Tottori silt, and Kaolin clay) were investigated by considering a concept of granular void ratio expressed in terms of sand structure. The cyclic shear strengths of the soil mixtures were also evaluated by increasing the fine content but no more than the threshold fine content. In the results, the cyclic deviator stress ratio decreased in dense soils whereas it increased in loose soils by increasing the fine content. In addition, a simple equation was proposed to predict the liquefaction resistance of sandy soils by evaluating the cyclic deviator stress ratio with a concept of equivalent granular void ratio.     

Experimental study on strength characteristics and microscopic mechanism of marine soft clays

Abstract

The effect of microstructure on shear strength of saturated marine clays was investigated by conducting a series of consolidated-drained (CD), consolidated-undrained (CU) triaxial shear tests and mercury intrusion porosimetry (MIP) tests on undisturbed and reconstitute specimens. The valuable findings from the experimental study are follows: (1) The shear strength of undisturbed specimens is lower than that of corresponding reconstituted specimens due to larger void ratio at the same confining pressure. However, undisturbed specimens have higher strength than reconstituted specimens when their void ratios are the same. (2) The main reason for the lower shear strength of reconstituted specimens with the same void ratio as undisturbed specimens is that more volume of inter-aggregate pores exists in the reconstituted specimens according to the MIP test results. And the difference in shear strength between undisturbed and reconstituted specimens is mainly caused by the difference in soil fabric. (3) The shear test results dealt with a reference void ratio, as a fabric index, show that there is a unique linear relation between strength and void ratio at failure to the reference void ratio. Moreover, the linear relation is suitable for other marine clays from the literature. Therefore, the reference void ratio can be used as a soil fabric index to normalize the strength characteristics of marine soft clays.     

Laboratory Study on the Hydraulic Conductivity and Pore Pressure of Sand-Silt Mixtures

The hydraulic conductivity plays a major role on the excess pore pressure generation during monotonic and cyclic loading of granular soils with fines. This paper aims to determine how much the hydraulic conductivity and pore pressure response of the sand-silt mixtures are affected by the percentage of fines and void ratio of the soil. The results of flexible wall permeameter and undrained monotonic triaxial tests performed on samples reconstituted from Chlef River sand with 0, 10, 20, 30, 40, and 50% nonplastic silt at an effective confining stress of 100 kPa and two relative densities (D_r = 20, and 91%) are presented and discussed. It was found that the pore pressure increases linearly with the increase of the fines content and logarithmically with the increase of the intergranular void ratio. The results obtained from this study reveal that the saturated hydraulic conductivity (k) of the sand mixed with 50% low plastic fines can be, on average, four orders of magnitude smaller than that of the clean sand. The results show also that the hydraulic conductivity decreases hyperbolically with the increase of the fines content and the intergranular void ratio.     

A Nondestructive Technique for Predicting the In Situ Void Ratio for Marine Sediments

Abstract

This study tests the hypothesis that the in situ void ratio of surficial marine sediments may be predicted from shear wave velocity-depth data with a reliability equal to that of other methods currently available. Shear wave velocity is fundamentally controlled by the number of grain-to-grain contacts per unit volume of material and by the effective stress across those contacts. In this study, three previously established empirical formulae are used to predict void ratio from velocity-depth data. Field data were acquired along a transect off the northern Californian coast across which water depth increased from 35 to 70 m and seafloor sediment type varied from sand to silty-sand, respectively. A towed seafloor sled device was used to collect shear wave refraction data, and a marked, systematic decrease in velocity was observed along the line, ranging from 35–70 m/s for the coarse, near-shore material to 25–40 m/s for the finer, offshore deposits. Void ratios predicted from these velocities were compared with data measured directly from box-core samples. Of the formulae used for prediction, two agree remarkably well with the control data. Both predicted and control values increase from 0.6–0.8 for the sandy material to 1.1–1.5 for the silty-sand. Thus, this study does not disprove the hypothesis set and demonstrates the potential of field shear wave velocity-depth data as a means of delineating spatial variation in void ratio for surficial marine sediments in a remote, nondestructive manner.     

基于ABAQUS的海底管道静水压溃压力的敏感性分析

局部屈曲压溃是海底管道发生稳定性破坏的一种形式,随着管道的刚度相对越来越柔,厚度相对越来越薄,管道发生屈曲压溃的问题也越来越突出。运用ABAQUS有限元分析软件进行管道的非线性屈曲分析,确定不同径厚比、初始椭圆度、轴向拉力和弯矩作用下的管道静水压溃压力,以分析静水压溃压力对这些因素的敏感性。     

Geotechnical Investigations at the Dalian Offshore Airport,China

Based on the geotechnical investigation data of artificial island at Dalian Offshore Airport, the spatial distribution of the physical and mechanical properties of deposit soils was statistically analyzed. The field investigation revealed that the deposit soils could be subdivided into three strata, i.e., the top marine deposit stratum, middle marine-continental deposit stratum, and deep continental deposit stratum. Field and laboratory test results demonstrated that the marine deposit soils had high water content (31.2% < w_n < 63.10%), large void ratio (0.88 < e₀ < 1.75), low permeability (k_v < 10^?6 cm/s), flow-plastic state (I_L > 1), under consolidated (OCR < 1), high compressibility (E_s < 4 MPa), low shear strength (11.7 kPa < c_u < 43.7 kPa), and low bearing capacity (0 < f_ak < 120 kPa), they could not be used as natural foundation. The marine-continental and continental deposits were normally consolidated to over-consolidated (OCR ≥ 1), medium compressibility (4 MPa < E_s < 20 MPa), high shear strength (29.7 kPa < c_u < 73.7 kPa), and high bearing capacity (f_ak > 120 kPa). In addition, regression analysis results showed that the compression ratio was positively correlated with the natural water content, the coefficient of vertical consolidation was negatively correlated with the plasticity index, and the coefficient of vertical permeability was positively correlated with the initial void ratio. The results of the field and laboratory tests were synthesized to provide a basis for reclamation design.     

Numerical study on long-term monopile foundation response

This paper analyzes the long-term monopile foundation that undergoes numerous mechanical cycles. The semiempirical scheme is adopted to involve a mechanical constitutive model to extract stress and strains at the first cycle and polynomial-type strain accumulation functions to track the progressive plastic deformation. In particular, the strain function contains the fundamental features that require simulating the long-term response of geomaterials: volumetric strain (terminal void ratio) and shear strain (shakedown or ratcheting), the strain accumulation rate, and stress obliquity. The numerical simulation shows evolution of displacements, pile rotation, and stress redistribution along the embedded pile as the number of load cycles increases. The analysis highlights that the pile rigidity affects the pattern of horizontal stress and displacement. The repetitive lateral load enhances the lateral load resistance due to soil densification along the pile.     

Settling of Kaolinite in Different Aqueous Environment

Settling characteristics of soils carry great importance for geotechnical engineers since sediments properties are formed during the settling of soil particles in an aqueous environment. In this study, settling characteristics of kaolinite are investigated. Different ionic strengths of NaCl, CaCl₂ and AlCl₃ were considered as a function of pH in aqueous environment of varying solid concentrations. Factors affecting the settling characteristics and fabric of kaolinitic sediments have been identified. The results of the study reveal that kaolinite settles in either flocculated or dispersed forms depending on pH and ion concentration. Flocculated settling occurs in acidic pH due to formation of flocs in edge-to-face structure with increasing positive charges at the particle edges. Dispersed settling occurs in alkaline pHs when ionic strength is low. When ionic strength is increased in alkaline pHs, kaolinite particles settle in flocculated form. Furthermore, the results show that pH has a significant role on the final sediment thickness or void ratio of kaolinite. Densely packed structures in alkaline and loosely packed structures in acidic aqueous environments are formed depending on pH level. Results also show that as the solid concentration increases, the settling rate decreases due to buoyancy effect. Finally, the zeta potential of kaolinite is correlated with the final sediment thickness or void ratio of kaolinite as a function of pH. This correlation proves that there is a good agreement between zeta potential and the final sediment thickness or void ratio, especially when the soil is settled in a dispersed form.     

Settling of Kaolinite in Different Aqueous Environment

Settling characteristics of soils carry great importance for geotechnical engineers since sediments properties are formed during the settling of soil particles in an aqueous environment. In this study, settling characteristics of kaolinite are investigated. Different ionic strengths of NaCl, CaCl₂ and AlCl₃ were considered as a function of pH in aqueous environment of varying solid concentrations. Factors affecting the settling characteristics and fabric of kaolinitic sediments have been identified. The results of the study reveal that kaolinite settles in either flocculated or dispersed forms depending on pH and ion concentration. Flocculated settling occurs in acidic pH due to formation of flocs in edge-to-face structure with increasing positive charges at the particle edges. Dispersed settling occurs in alkaline pHs when ionic strength is low. When ionic strength is increased in alkaline pHs, kaolinite particles settle in flocculated form. Furthermore, the results show that pH has a significant role on the final sediment thickness or void ratio of kaolinite. Densely packed structures in alkaline and loosely packed structures in acidic aqueous environments are formed depending on pH level. Results also show that as the solid concentration increases, the settling rate decreases due to buoyancy effect. Finally, the zeta potential of kaolinite is correlated with the final sediment thickness or void ratio of kaolinite as a function of pH. This correlation proves that there is a good agreement between zeta potential and the final sediment thickness or void ratio, especially when the soil is settled in a dispersed form.     

多波束海底地形数据空值区域的插值填补方法分析

由于边界误差剔除、测线布设过于稀疏等因素影响,利用多波束数据生成高分辨率DEM时,常常会存在一些水深空值单元或区域。为了对这些数据空值区域进行可靠填补,在考虑地形特征及空值单元大小的情况下,利用IDW、Spline、Kriging、TIN四种插值方法对某区域多波束海底DEM空值区域进行直接内插填补试验,结果表明插值算法的选取不仅受地形类型限制,而且与空值区域的大小也密切相关。     

Analysis of the Tsunami of December 26, 2004, on the Kerala Coast of India—Part III: Inundation and Initial Withdrawal

During the Indian Ocean tsunami of December 26, 2004, specific observations were made by our survey team about the arrival times of several tsunami waves, their amplitudes, maximum extent of horizontal inundation on land and initial withdrawal of the ocean. Here the observations on the horizontal inundation and initial withdrawal are presented and briefly discussed.     

Analysis of the Tsunami of December 26, 2004, on the Kerala Coast of India—Part III: Inundation and Initial Withdrawal

During the Indian Ocean tsunami of December 26, 2004, specific observations were made by our survey team about the arrival times of several tsunami waves, their amplitudes, maximum extent of horizontal inundation on land and initial withdrawal of the ocean. Here the observations on the horizontal inundation and initial withdrawal are presented and briefly discussed.     

关于Mckenzie沉积盆地初始沉降公式的修正

根据Airy均衡原理对Mckenzie沉积盆地初始沉降公式进行了修正,并导出了公式的正确表达式 S=(a[(ρ_o-ρ_c)t_c/a(1-(aT_1t_c)/(2a))-(aT_1ρ_o)/2](1-1/β))/(ρ_o(1-aT_1)-ρ_w)     

On the compression behavior of remolded cement-admixed soft clay

Although extensive research has been performed on the mechanical properties of cement-stabilized clays, quite a few attempts have been made on the compression behavior of remolded cement-admixed clays. The results from oedometer tests have been discussed to investigate the compressibility of remolded cement-admixed clays, taking into consideration cement amount and curing time. The findings show that the difference in shape and position of compression curves is attributed to cement amount and curing time. Most compression index (C_c) values of remolded cement-admixed clays are greater than those of untreated clay due to the presence of remolded yield stress σ′_yr that is closely related to initial water content and clay fabric. Based on the obtained test data, the relationships of C_c vs. e₀, C_c vs. w₀, C_c vs. e₁, C_c vs. e_yr, and σ′_yr vs. e_yr are preliminarily discussed and quantitatively established. Especially, an important divergence of void index I_v at effective stress σ′_v less than remolded yield stress σ′_yr can be observed at different cement amounts and curing durations. Being independent on cement amount, curing time, and initial state of soil, an excellent convergence occurs at stress σ′_v greater than yield stress σ′_yr. The normalized compression curves of I_v vs. σ′_v at σ′_v?>?σ′_y can be expressed by a unique line that agrees well with intrinsic compression line (ICL) and extended ICL.