首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
Research over the last decade has shown that the suspended sediment loads of many rivers are dominated by composite particles. These particles are also known as aggregates or flocs, and are commonly made up of constituent mineral particles, which evidence a wide range of grain sizes, and organic matter. The resulting in situ or effective particle size characteristics of fluvial suspended sediment exert a major control on all processes of entrainment, transport and deposition. The significance of composite suspended sediment particles in glacial meltwater streams has, however, not been established. Existing data on the particle size characteristics of suspended sediment in glacial meltwaters relate to the dispersed mineral fraction (absolute particle size), which, for certain size fractions, may bear little relationship to the effective or in situ distribution. Existing understanding of composite particle formation within freshwater environments would suggest that in‐stream flocculation processes do not take place in glacial meltwater systems because of the absence of organic binding agents. However, we report preliminary scanning electron microscopy data for one Alpine and two Himalayan glaciers that show composite particles are present in the suspended sediment load of the meltwater system. The genesis and structure of these composite particles and their constituent grain size characteristics are discussed. We present evidence for the existence of both aggregates, or composite particles whose features are largely inherited from source materials, and flocs, which represent composite particles produced by in‐stream flocculation processes. In the absence of organic materials, the latter may result solely from electrochemical flocculation in the meltwater sediment system. This type of floc formation has not been reported previously in the freshwater fluvial environment. Further work is needed to test the wider significance of these data and to investigate the effective particle size characteristics of suspended sediment associated with high concentration outburst events. Such events make a major contribution to suspended sediment fluxes in meltwater streams and may provide conditions that are conducive to composite particle formation by flocculation. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

2.
Deposition and storage of fine‐grained (<62·5 μm) sediment in the hyporheic zone of gravel bed rivers frequently represents an important cause of aquatic habitat degradation. The particle size characteristics of such fine‐grained bed sediment (FGBS) exert an important control on its hydrodynamic properties and environmental impact. Traditionally, particle size analysis of FGBS in gravel bed rivers has focused on the absolute size distribution of the chemically dispersed mineral fraction. However, recent work has indicated that in common with fluvial suspended sediment, significant differences may exist between the absolute and the in situ, or effective, particle size composition of FGBS, as a result of the existence of aggregates, or composite particles. In the investigation reported in this paper, sealable bed traps that could be remotely opened to sample sediment deposited during specific storm runoff events and a laser back‐scatter probe were used to quantify the temporal and spatial variability of both the absolute and effective particle size composition of FGBS, and the associated suspended sediment from four gravel bed rivers in the Exe Basin, Devon, UK. The absolute particle size distributions of both the FGBS and suspended sediment evidenced c. >95%<62·5 μm sized primary particles and displayed a seasonal winter–summer fining, while the opposite trend was displayed by the effective particle size distribution of the FGBS and suspended sediment. The effective particle size distributions of both were typically highly aggregated, comprising up to 68%>62·5 μm sized particles. Spatial variation in the effective particle size and aggregation parameters was of secondary importance relative to temporal variation. The effective particle size distribution of the FGBS was consistently coarser and more aggregated than the associated suspended sediment and there was evidence of aggregate break‐up in samples of resuspended bed sediment. The implications of these findings for sediment transport modelling are considered. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

3.
Field data from the Rio Paraná, Argentina, are used to examine patterns of suspended sediment transport over a sand dune. Measurements of three‐dimensional velocity are made with an acoustic Doppler current profiler whilst suspended sediment concentration and particle size have been quantified using a laser in situ sediment scattering transmissometer. Suspended sediment concentration and streamwise and vertical sediment flux are highest close to the bed, with an upward vertical flux over the stoss side of the dune and downward flux over the lee side. Suspended sediment concentrations are higher over the crest compared with the trough and suspended sediment is coarsest near the bed. About 17% of the suspended‐load transported over the crest is deposited in the lee side before it reaches the trough. Most of this deposited sand is coarser sediment that originates close to the bed over the crest, a result consistent with simulations based on the model of Mohrig and Smith (Water Resources Research 1996; 32: 3207–3217) for the excursion lengths of sediment dispersed in the lee side of a dune. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

4.
Due to a lack of data on settling velocities (ws) and grain size distributions (GSDs) in ?oodplain environments, sedimentation models often use calibrated rather than measured parameters. Since the characteristics of suspended matter differ from those of deposited sediment, it is impossible to derive the ws and GSD from the latter. Therefore, one needs to measure in situ suspended sediment concentrations (SSCs), settling velocities, effective grain sizes and sedimentation ?uxes. For this purpose we used the LISST‐ST, a laser particle sizer combined with a settling tube. In 2002 (twice) and 2004, we located the LISST‐ST with an optical backscatter sensor and sediment traps in two ?oodplains in The Netherlands: one along the unembanked IJssel River, another along the embanked Waal River. Measurements revealed that the SSC in the ?oodplains varied in relation to the SSC in the river channel. Smaller ?ocs dominated the SSC, while larger ?ocs dominated the potential sedimentation ?uxes. The in situ GSD in the IJssel ?oodplain was signi?cantly coarser than in the Waal ?oodplain, while the dispersed median grain sizes were equal for both ?oodplains. Therefore, the dispersed median grain size was two to ?ve times smaller than the effective one. The in situ grain size exhibited a signi?cant positive relationship with ws, although the ws for the largest ?ocs showed high variability. Consequently, the variability in sedimentation ?uxes was also large. In the actual sedimentation ?uxes, and hence in sedimentation models, in situ grain sizes up to about 20 µm can be neglected. In ?oodplain sedimentation models the relation between settling velocity and in situ grain size can be used instead of Stokes's law, which is only valid for dispersed grain sizes. These models should also use adequate data on ?ow conditions as input, since these strongly in?uence the suspended sediment characteristics. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

5.
Suspended sediment has been identified as a vector for nutrient and contaminant transport in the fluvial environment. A time‐integrated sampler (the Phillips sampler), which emerged over a decade ago as a cost‐effective tool for in situ suspended sediment collection, is increasingly being used to collect samples for the analysis of sediment properties such as particle size composition, and nutrient and contaminant concentrations. This study evaluates the sampler under both flume and field conditions for efficiency in the mass and grain size of the suspended sediment collected. The sampler was tested in a flume using both kaolinite and sediment samples (sieved to < 180 µm) collected from the Quesnel River, British Columbia, Canada. In the kaolinite trails, the sampler preferentially collected coarser grain sizes compared to the original sediment, probably due to finer sediment remaining in suspension and therefore passing through the sampler, and also possibly due to flocculation of the kaolinite upon introduction to the flume. Conversely, the sampler collected river sediment that was finer than the original sediment, probably due to some settling of coarser sediment observed at the bottom of the flume. Once allowance was made for these operational issues associated with the flume, maximum sediment mass efficiency for kaolinite and river sediment was 43% and 87%, respectively. Sediment collected by the time‐integrated sampler during field deployment and adjacent channel bed sediment were also compared. The sampler collected sediment with a representative grain size distribution. However, there were differences in the geochemical (arsenic and selenium) concentrations of channel bed sediment and sediment collected by the Phillips sampler which may be a function of differences in the behavior of geochemical elements associated with the two types of sediment. This work suggests that further research is needed to evaluate the role of the Phillips sampler in collecting sediment for contaminant and nutrient analysis. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

6.
Fine‐grained (<62·5 µm) suspended sediment transport is a key component of the geochemical flux in most fluvial systems. The highly episodic nature of suspended sediment transport imposes a significant constraint on the design of sampling strategies aimed at characterizing the biogeochemical properties of such sediment. A simple sediment sampler, utilizing ambient flow to induce sedimentation by settling, is described. The sampler can be deployed unattended in small streams to collect time‐integrated suspended sediment samples. In laboratory tests involving chemically dispersed sediment, the sampler collected a maximum of 71% of the input sample mass. However, under natural conditions, the existence of composite particles or flocs can be expected to increase significantly the trapping efficiency. Field trials confirmed that the particle size composition and total carbon content of the sediment collected by the sampler were representative statistically of the ambient suspended sediment. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

7.
Since the 1970s, there has been both continuing and growing interest in developing accurate estimates of the annual fluvial transport (fluxes and loads) of suspended sediment and sediment‐associated chemical constituents. This study provides an evaluation of the effects of manual sample numbers (from 4 to 12 year?1) and sample scheduling (random‐based, calendar‐based and hydrology‐based) on the precision, bias and accuracy of annual suspended sediment flux estimates. The evaluation is based on data from selected US Geological Survey daily suspended sediment stations in the USA and covers basins ranging in area from just over 900 km2 to nearly 2 million km2 and annual suspended sediment fluxes ranging from about 4 Kt year?1 to about 200 Mt year?1. The results appear to indicate that there is a scale effect for random‐based and calendar‐based sampling schemes, with larger sample numbers required as basin size decreases. All the sampling schemes evaluated display some level of positive (overestimates) or negative (underestimates) bias. The study further indicates that hydrology‐based sampling schemes are likely to generate the most accurate annual suspended sediment flux estimates with the fewest number of samples, regardless of basin size. This type of scheme seems most appropriate when the determination of suspended sediment concentrations, sediment‐associated chemical concentrations, annual suspended sediment and annual suspended sediment‐associated chemical fluxes only represent a few of the parameters of interest in multidisciplinary, multiparameter monitoring programmes. The results are just as applicable to the calibration of autosamplers/suspended sediment surrogates currently used to measure/estimate suspended sediment concentrations and ultimately, annual suspended sediment fluxes, because manual samples are required to adjust the sample data/measurements generated by these techniques so that they provide depth‐integrated and cross‐sectionally representative data. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.  相似文献   

8.
This study examines the particle size characteristics of hillslope soils and fluvial suspended sediments in an agricultural catchment. Samples of surface runoff and stream flow were collected periodically and analysed for the size distributions of the effective (undispersed) sediment. This sediment was subsequently dispersed and the ultimate size distributions determined. The median effective particle size of stream suspended sediment was considerably coarser than the median ultimate particle size, indicating that most of the load included a substantial proportion of aggregates. Moreover, the proportion of fine material (i.e. silt and clay) increased, and the proportion of sand-sized material decreased, with increasing discharge. This decrease in sediment size with increased flow, which is contrary to the traditional assumption of a positive discharge/particle size relationship, is thought to reflect: (i) the influx of silt and clay, predominantly the former, originating on the catchment slopes and brought to the stream by overland flow along vehicle wheelings, roads and tracks; and (ii) erosion of fine material from the channel bed and banks. During large storms, however, the proportion of sand-sized sediment increased during the rising limb of the hydrograph, as a result of the entrainment of coarser source material from the valley floor during overbank flooding. The stream suspended sediment was finer than the catchment soils and considerably finer than material eroding from the catchment slopes during storms. The degree of clay and silt enrichment in the suspended sediments was largely the result of preferential deposition of the coarser fraction during the transport and delivery of sediment from its source to basin outlet. The data from this study confirm that a significant mode of sediment transport in fluvial systems is in the form of aggregates, and that the dispersed sediment size distribution is inappropriate for determining the transportability of sediment by flow. © 1997 by John Wiley & Sons, Ltd.  相似文献   

9.
In situ turbidity meters are being increasingly used to generate continuous records of suspended sediment concentration in rivers. However, the usefulness of the information obtained depends heavily on the existence of a close relationship between fluctuations in suspended sediment concentration and turbidity and the calibration procedure that relates suspended sediment concentration to the turbidity meter's signal. This study assesses the relationship between suspended sediment concentration and turbidity for a small (1·19 km2) rural catchment in southern Brazil and evaluates two calibration methods by comparing the estimates of suspended sediment concentration obtained from the calibrated turbidity readings with direct measurements obtained using a USDH 48 suspended sediment sampler. With the first calibration method, the calibration relationship is derived by relating the turbidity readings to simultaneous measurements of concentration obtained from suspended sediment samples collected from the vicinity of the turbidity probe during flood events. With the second method, the calibration is based on the readings obtained from the turbidity meter when the probe immersed in samples of known concentration prepared using soils collected from the catchment. Overall, there was a close link between fluctuations in suspended sediment concentration and turbidity in the stream at the outlet of the catchment, and the estimates of sediment concentration obtained using the first calibration method corresponded closely with the conventionally measured sediment concentrations. However, use of the second calibration method introduced appreciable errors. When the estimated sediment concentrations were compared with the measured values, the mean errors were ± 122 mg l?1 and + 601 mg l?1 for the first and second calibration procedures respectively. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

10.
Investigating the transport of suspended solids by water sampling usually leads to an underestimation of loads and an unrealistically high sampling frequency is required to properly characterize temporal trends. An alternative method is to use in situ optical turbidimeters to estimate the suspended solids concentration; however, the relationship between turbidity and suspended solids concentration is potentially confounded by variations in particle size, particle composition and water colour. Field measurements, and laboratory measurements using the type of natural material suspended in streamwater, were made to quantify the influences of these factors on nephelometric turbidity (Hach 2100A) and attenuance turbidity (Partech 7000 3RP MKII). The attenuance turbidity was approximately 2.5 times higher than nephelometric turbidity. The turbidity instruments were most sensitive to dispersions with a median diameter of 1.2-1.4γm. Particle size variation can cause the turbidity to vary by a factor of four for the same concentration of suspended solids. However, the numerous close correlations between turbidity and suspended solids concentration reported previously suggests that either the particle size variations are not usually great, or that particle size variations are often associated with variations in suspended solids concentration. For the same concentration and particle size, organic particles gave attenuance turbidity values two to three times higher than mineral particles. However, shortterm temporal variations from purely organic to purely mineral particle loads are rare in nature, so variations in the percentage of organic matter in the paniculate load will not confound turbidity to this extent. Coloured dissolved organic matter is unlikely to alter the turbidity reading by more than 10%. An adequate relationship between turbidity measured in the field and suspended solids concentration should be expected in most situations. Some variance can be tolerated because a continuous estimate of suspended solids concentration overcomes the problem of infrequent sampling, which is the greatest source of error in the estimation of stream sediment loads.  相似文献   

11.
12.
In spite of the important relationship between sediment particle size and the transport/deposition of adsorbed pollutants in fluvial systems, little information regarding the size characteristics of suspended sediment transported by southern Ontario Great Lakes tributaries is currently available. This paper examines long-term sediment and hydrometric data collected by the Water Resources Branch of Environment Canada in order to provide information on (1) typical particle size distributions of suspended sediment, (2) relationships between source material and particle size characteristics of suspended sediment, and (3) temporal variation in the particle size characteristics of suspended sediment from six southern Ontario rivers. Results illustrate the complex behaviour and variability of sediment particle size transport in these rivers and demonstrate the need for a better understanding of seasonal effects on sediment availability and conveyance processes in fluvial systems.  相似文献   

13.
For the southern branch of the Rhine–Meuse estuary, The Netherlands, a two-dimensional horizontal suspended sediment transport model was constructed in order to evaluate the complicated water quality management of the area. The data needed to calibrate the model were collected during a special field survey at high river runoff utilizing a number of techniques: (1) turbidity probes were used to obtain suspended sediment concentration profiles; (2) air-borne remote sensing video recordings were applied in order to obtain information concerning the spatial distribution of the suspended sediment concentration; (3) an acoustic probe (ISAC) was used to measure cohesive bed density profiles and (4) an in situ underwater video camera (VIS) was deployed to collect video recordings of the suspended sediment. These VIS data were finally processed to fall velocity and diameter distributions and were mainly used to improve insight into the relevant transport processes, indicating significant erosion of sand from the upstream Rhine branch. For quantitative calibration of the model, the data from the turbidity profiles were used. Sedimentation and erosion were modelled according to Krone and Partheniades. The model results showed a good overall fit to the measurements, with a mean absolute error of 18 per cent (standard fault = 1 per cent), corresponding to concentrations of about 0·020 (upstream) to 0·005 kg m−3 (downstream). The overall correlation between observed and simulated suspended sediment concentrations was 0·85. The remote sensing video recordings were used for a qualitative calibration of the model. The distribution pattern of the suspended sediment on these photos was reproduced quite well by the model. However, a more accurate calibration technique is needed to enable the use of aerial remote sensing as a quantitative calibration method. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

14.
This study investigates the consequences of flocculation for sediment flux in glacier‐fed Lillooet Lake, British Columbia based on density, fractal dimension, in situ profiles of sediment concentration and size distribution, and settling velocity equations presented in the literature. Sediment flux attributed to macroflocs during the late spring and summer accounts for a significant portion of sediment flux in the lake, equivalent to at least one‐quarter of the average annual sediment flux. Fine sediment is reaching the lake floor faster in flocs than occurs if settling as individual grains. This flux varies both spatially and temporally over the observation period, suggesting a link between deposition via flocculation and the properties of bottom sediments. Macrofloc flux increased through June, reached a peak during July, and then declined into August. Macrofloc flux was greatest in the distal end of the first basin, approximately 10 km from the point of inflow. Relatively high excess densities (~0·1 g cm–3 at 500 µm) for flocs in situ are consistent with a composition dominated by inorganic primary particles. Microlaminations within Lillooet Lake varves have been linked by earlier workers to discharge events, and the action of turbidity currents, emanating from the Lillooet River. While turbidity currents undoubtedly occur in Lillooet Lake, these results demonstrate flocculation as an adjunct process linking discharge, lake level, macrofloc flux, bulk density and microlaminations. In situ measurements of sediment settling velocity in glacier‐fed lakes are required to better constrain flux rates, and permit comparison between flocculation in lacustrine environments with existing studies of estuarine, marine and fluvial flocculation. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

15.
Flocculation has an important impact on particle trapping in estuarine turbidity maximum (ETM) through associated increases in particle settling velocity. To quantify the importance of the flocculation processes, a size-resolved flocculation model is implemented into an ocean circulation model to simulate fine-grained particle trapping in an ETM. The model resolves the particle size from robust small flocs, about 30 μm, to very large flocs, over 1000 μm. An idealized two-dimensional model study is performed to simulate along-channel variations of suspended sediment concentrations driven by gravitational circulation and tidal currents. The results indicate that the flocculation processes play a key role in generating strong tidal asymmetrical variations in suspended sediment concentration and particle trapping. Comparison with observations suggests that the flocculation model produces realistic characteristics of an ETM.  相似文献   

16.
Most of the existing data on the effective particle size characteristics of fluvial suspended sediment derive from instantaneous sampling methods that may not be representative of the overall suspended sediment loads. This presents difficulties when there is a need to incorporate effective particle size data into numerical models of floodplain sedimentation and sediment‐associated contaminant transfer. We have used a field‐based water elutriation apparatus (WEA) to assemble a large (36 flood) database on the time‐integrated nature of the effective and absolute particle size characteristics of suspended sediment in four subcatchments of the River Exe basin of southwest England. These catchments encompass a wide range of terrains and fluvial environments that are broadly representative of much of the UK and temperate, low relief northwest Europe. The WEA provides important data on the physical characteristics of composite particles that are not attainable using other methods. This dataset has allowed, for the first time, detailed interbasin comparisons of the time‐integrated particle size characteristics of suspended sediment and reliable estimates of the contribution of five effective size classes to the mean annual suspended sediment load of the study catchments. The suspended sediment load of each river is dominated by composite rather than primary particles, with, for example, almost 60% (by mass) of the sediment load of the River Exe at Thorverton transported as composite particles > 16 µm in size. All the effective size classes contain significant clay components. A key outcome of this study is the recognition that each catchment has a distinctive time‐integrated effective particle size signature. In addition, the time‐integrated effective particle size characteristics of the suspended loads in each of the catchments display much greater spatial variability than the equivalent absolute particle size distributions. This indicates that the processes producing composite particles vary significantly between these catchments, and this has important implications for our understanding of the dynamics of suspended sediment properties. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

17.
The accurate measurement of suspended sediment (<200 μm) in aquatic environments is essential to understand and effectively manage changes to sediment, nutrient, and contaminant concentrations on both temporal and spatial scales. Commonly used sampling techniques for suspended sediment either lack the ability to accurately measure sediment concentration (e.g., passive sediment samplers) or are too expensive to deploy in sufficient number to provide landscape‐scale information (e.g., automated discrete samplers). Here, we evaluate a time‐integrated suspended sediment sampling technique, the pumped active suspended sediment (PASS) sampler, which collects a sample that can be used for the accurate measurement of time‐weighted average (TWA) suspended sediment concentration and sediment particle size distribution. The sampler was evaluated against an established passive time‐integrated suspended sediment sampling technique (i.e., Phillips sampler) and the standard discrete sampling method (i.e., manual discrete sampling). The PASS sampler collected a sample representative of TWA suspended sediment concentration and particle size distribution of a control sediment under laboratory conditions. Field application of the PASS sampler showed that it collected a representative TWA suspended sediment concentration and particle size distribution during high flow events in an urban stream. The particle size distribution of sediment collected by the PASS and Phillips samplers were comparable and the TWA suspended sediment concentration of the samples collected using the PASS and discrete sampling techniques agreed well, differing by only 4% and 6% for two different high flow events. We should note that the current configuration of the PASS sampler does not provide a flow‐weighted measurement and, therefore, is not suitable for the determination of sediment loads. The PASS sampler is a simple, inexpensive, and robust in situ sampling technique for the accurate measurement of TWA suspended sediment concentration and particle size distribution.  相似文献   

18.
Field measurements have been carried out to obtain more quantitative knowledge on the longitudinal distribution of the fine-grained sediment dynamics in the Ems Estuary. Both the short-term (time scale < tidal period) and the long-term (tidally averaged) fine-grained sediment transports have been investigated. It is shown that the short-term erosion/sedimentation cycles are most characteristic and are the building blocks for the ultimate long-term transports. Herein, the macroflocs play a key role. The macroflocs had sizes in the range of 200 to 700?μm, sometimes more than 1?mm, and survived high current velocities. The settling velocities were in the range of 0.5 to 8?mm/s. Turbulence intensities and suspended sediment concentration are of utmost importance for the settling properties of the sediment, but the “flocculation ability??of the suspended sediment is shown to be of equal importance. The suspended sediment concentration is only important at low levels of turbulence. At high levels of turbulence, the limiting properties of turbulence dominate. It is demonstrated that the surface properties of the suspended sediment particles are of prime importance for the flocculation ability of the water/sediment mixture, as do the sizes of the resuspended microflocs. Special attention is given to the longitudinal distribution of the sizes and settling properties of the macroflocs as well as of the sediment transports. The flocculation ability was shown to vary almost one order of magnitude along the estuary. These higher flocculation abilities in the direction of higher salinities are responsible for the increase of the sizes of the macroflocs in the seaward direction. Therefore, notwithstanding the low suspended sediment concentrations at the seaward boundary of the Ems Estuary, large macroflocs and corresponding high settling velocities were observed in this area. It explains that, in the Ems Estuary, no distinct effect was determined of the suspended sediment concentration on the settling properties of the suspended macroflocs.  相似文献   

19.
When fine particles are involved, cohesive properties of sediment can result in flocculation and significantly complicate sediment process studies. We combine data from field observations and state-of-the-art modeling to investigate and predict flocculation processes within a hypertidal estuary. The study site is the Welsh Channel located at the entrance of the Dee Estuary in Liverpool Bay. Field data consist of measurements from a fixed site deployment during 12–22 February 2008. Grain size, suspended sediment volume concentration, and current velocity were obtained hourly from moored instruments at 1.5 m above bed. Near-bottom water samples taken every hour from a research vessel are used to convert volume concentrations to mass concentrations for the moored measurements. We use the hydrodynamic model Proudman Oceanographic Laboratory Coastal Ocean Modelling System (POLCOMS) coupled with the turbulence model General Ocean Turbulence Model (GOTM) and a sediment module to obtain three-dimensional distributions of suspended particulate matter (SPM). Flocculation is identified by changes in grain size. Small flocs were found during flood and ebb periods—and correlate with strong currents—due to breakup, while coarse flocs were present during slack waters because of aggregation. A fractal number of 2.4 is found for the study site. Turbulent stresses and particle settling velocities are estimated and are found to be related via an exponential function. The result is a simple semiempirical formulation for the fall velocity of the particles solely depending on turbulent stresses. The formula is implemented in the full three-dimensional model to represent changes in particle size due to flocculation processes. Predictions from the model are in agreement with observations for both settling velocity and SPM. The SPM fortnight variability was reproduced by the model and the concentration peaks are almost in phase with those from field data.  相似文献   

20.
An in-channel surficial depositional feature (surficial fine-grained laminae) composed of loosely bound fine sediment deposited during low flow conditions has often been observed in river systems in south-western Ontario. The physical characteristics of this feature have been determined by a direct observation image analysis system. This sediment consists primarily of flocculated fine-grained material. The size distributions of surficial fine-grained laminae and suspended sediment were not significantly different. Each distribution is bimodal in nature and shows a characteristic grain size deficiency in the 4-5 μm size range. This observation suggests that flocculation and not low discharge or low competence is the dominant mechanism for the formation of surficial fine-grained laminae under conditions of low flow in fluvial systems of south-western Ontario. A quantitative assessment of this feature shows its potential importance as a source of fine-grained sediment and associated contaminants for downstream transport.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号