Anisotropic models to account for large borehole washouts to estimate gas hydrate saturations in the Gulf of Mexico Gas Hydrate Joint Industry Project Leg II Alaminos Canyon 21 B well

Through the use of 3-D seismic amplitude mapping, several gas hydrate prospects were identified in the Alaminos Canyon (AC) area of the Gulf of Mexico. Two locations were drilled as part of the Gulf of Mexico Gas Hydrate Joint Industry Project Leg II (JIP Leg II) in May of 2009 and a comprehensive set of logging-while-drilling (LWD) logs were acquired at each well site. LWD logs indicated that resistivity in the range of ∼2 ohm-m and P-wave velocity in the range of ∼1.9 km/s were measured in the target sand interval between 515 and 645 feet below sea floor. These values were slightly elevated relative to those measured in the sediment above and below the target sand. However, the initial well log analysis was inconclusive regarding the presence of gas hydrate in the logged sand interval, mainly because large washouts caused by drilling in the target interval degraded confidence in the well log measurements. To assess gas hydrate saturations in the sedimentary section drilled in the Alaminos Canyon 21 B (AC21-B) well, a method of compensating for the effect of washouts on the resistivity and acoustic velocities was developed. The proposed method models the washed-out portion of the borehole as a vertical layer filled with sea water (drilling fluid) and the apparent anisotropic resistivity and velocities caused by a vertical layer are used to correct the measured log values. By incorporating the conventional marine seismic data into the well log analysis, the average gas hydrate saturation in the target sand section in the AC21-B well can be constrained to the range of 8–28%, with 20% being our best estimate.     

Rock physics-based seismic trace analysis of unconsolidated sediments containing gas hydrate and free gas in Green Canyon 955, Northern Gulf of Mexico

The gas hydrate petroleum system at the 2009 Gulf of Mexico Gas Hydrate Joint Industry Project Leg II (JIP Leg II) Green Canyon 955 (GC955) site shows a complex seismic amplitude and waveform response of highly negative and positive amplitudes with continuous and discontinuous character within inferred gas-hydrate- and gas-bearing sand reservoirs. Logging-while-drilling (LWD) data obtained during JIP Leg II and conventional 3-D seismic data allowed for the identification of thick highly concentrated hydrate layers by integrating rock physics modeling, amplitude and thin layer analysis, and spectral decomposition. Rock physics modeling with constraints from three JIP LWD holes allowed for the analysis of variations in acoustic amplitude characteristics as a product of hydrate saturation, gas saturation, and reservoir thickness. Using the well log-derived acoustic models, thick highly concentrated gas hydrate with and without underlying free gas accumulations have been identified. These results suggest that thick highly concentrated gas-hydrate-bearing sand units (with thicknesses greater than half of the seismic tuning thickness and gas hydrate saturations greater than 50%) underlain by gas can be differentiated from sands containing only gas, but thin gas-hydrate-bearing sand units with low gas hydrate concentrations (with thicknesses less than half of the seismic tuning thickness and gas hydrate saturations less than 50%) are difficult to identify from post-stack seismic amplitude data alone. Within GC955, we have identified six zones with seismic amplitude anomalies interpreted as being caused by gas hydrate deposits with variable lateral extent, thickness and saturation, and in some cases overlying free-gas-bearing intervals. Synthetic seismic images produced from well-log- and model-derived velocity and density distributions mimic similar reflection characteristics in the corresponding field seismic data.     

Pre- and post-drill comparison of the Mount Elbert gas hydrate prospect, Alaska North Slope

In 2006, the United States Geological Survey (USGS) completed a detailed analysis and interpretation of available 2-D and 3-D seismic data, along with seismic modeling and correlation with specially processed downhole well log data for identifying potential gas hydrate accumulations on the North Slope of Alaska. A methodology was developed for identifying sub-permafrost gas hydrate prospects within the gas hydrate stability zone in the Milne Point area. The study revealed a total of 14 gas hydrate prospects in this area.In order to validate the gas hydrate prospecting protocol of the USGS and to acquire critical reservoir data needed to develop a longer-term production testing program, a stratigraphic test well was drilled at the Mount Elbert prospect in the Milne Point area in early 2007. The drilling confirmed the presence of two prominent gas-hydrate-bearing units in the Mount Elbert prospect, and high quality well logs and core data were acquired. The post-drill results indicate pre-drill predictions of the reservoir thickness and the gas-hydrate saturations based on seismic and existing well data were 90% accurate for the upper unit (hydrate unit D) and 70% accurate for the lower unit (hydrate unit C), confirming the validity of the USGS approach to gas hydrate prospecting. The Mount Elbert prospect is the first gas hydrate accumulation on the North Slope of Alaska identified primarily on the basis of seismic attribute analysis and specially processed downhole log data. Post-drill well log data enabled a better constraint of the elastic model and the development of an improved approach to the gas hydrate prospecting using seismic attributes.     

Pore- and fracture-filling gas hydrate reservoirs in the Gulf of Mexico Gas Hydrate Joint Industry Project Leg II Green Canyon 955 H well

High-quality logging-while-drilling (LWD) downhole logs were acquired in seven wells drilled during the Gulf of Mexico Gas Hydrate Joint Industry Project Leg II in the spring of 2009. Well logs obtained in one of the wells, the Green Canyon Block 955 H well (GC955-H), indicate that a 27.4-m thick zone at the depth of 428 m below sea floor (mbsf; 1404 feet below sea floor (fbsf)) contains gas hydrate within sand with average gas hydrate saturations estimated at 60% from the compressional-wave (P-wave) velocity and 65% (locally more than 80%) from resistivity logs if the gas hydrate is assumed to be uniformly distributed in this mostly sand-rich section. Similar analysis, however, of log data from a shallow clay-rich interval between 183 and 366 mbsf (600 and 1200 fbsf) yielded average gas hydrate saturations of about 20% from the resistivity log (locally 50−60%) and negligible amounts of gas hydrate from the P-wave velocity logs. Differences in saturations estimated between resistivity and P-wave velocities within the upper clay-rich interval are caused by the nature of the gas hydrate occurrences. In the case of the shallow clay-rich interval, gas hydrate fills vertical (or high angle) fractures in rather than filling pore space in sands. In this study, isotropic and anisotropic resistivity and velocity models are used to analyze the occurrence of gas hydrate within both the clay-rich and sand dominated gas-hydrate-bearing reservoirs in the GC955-H well.     

Evidence of gas hydrate accumulation and its resource estimation in Andaman deep water basin from seismic and well log data

2D and 3D seismic reflection and well log data from Andaman deep water basin are analyzed to investigate geophysical evidence related to gas hydrate accumulation and saturation. Analysis of seismic data reveals the presence of a bottom simulating reflector (BSR) in the area showing all the characteristics of a classical BSR associated with gas hydrate accumulation. Double BSRs are also observed on some seismic sections of area (Area B) that suggest substantial changes in pressure–temperature (P–T) conditions in the past. The manifestation of changes in P–T conditions can also be marked by the varying gas hydrate stability zone thickness (200–650 m) in the area. The 3D seismic data of Area B located in the ponded fill, west of Alcock Rise has been pre-stack depth migrated. A significant velocity inversion across the BSR (1,950–1,650 m/s) has been observed on the velocity model obtained from pre-stack depth migration. The areas with low velocity of the order of 1,450 m/s below the BSR and high amplitudes indicate presence of dissociated or free gas beneath the hydrate layer. The amplitude variation with offset analysis of BSR depicts increase in amplitude with offset, a similar trend as observed for the BSR associated with the gas hydrate accumulations. The presence of gas hydrate shown by logging results from a drilled well for hydrocarbon exploration in Area B, where gas hydrate deposit was predicted from seismic evidence, validate our findings. The base of the hydrate layer derived from the resistivity and acoustic transit-time logs is in agreement with the depth of hydrate layer interpreted from the pre-stack depth migrated seismic section. The resistivity and acoustic transit-time logs indicate 30-m-thick hydrate layer at the depth interval of 1,865–1,895 m with 30 % hydrate saturation. The total hydrate bound gas in Area B is estimated to be 1.8 × 10¹⁰ m³, which is comparable (by volume) to the reserves in major conventional gas fields.     

Low-amplitude BSRs and gas hydrate concentration on the northern margin of the South China Sea

The passive northern continental margin of the South China Sea is rich in gas hydrates, as inferred from the occurrence of bottom-simulating reflectors (BSR) and from well logging data at Ocean Drilling Program (ODP) drill sites. Nonetheless, BSRs on new 2D multichannel seismic reflection data from the area around the Dongsha Islands (the Dongsha Rise) are not ubiquitous. They are confined to complex diapiric structures and active fault zones located between the Dongsha Rise and the surrounding depressions, implying that gas hydrate occurrence is likewise limited to these areas. Most of the BSRs have low amplitude and are therefore not clearly recognizable. Acoustic impedance provides information on rock properties and has been used to estimate gas hydrate concentration. Gas hydrate-bearing sediments have acoustic impedance that is higher than that of the surrounding sediments devoid of hydrates. Based on well logging data, the relationship between acoustic impedance and porosity can be obtained by a linear regression, and the degree of gas hydrate saturation can be determined using Archie’s equation. By applying these methods to multichannel seismic data and well logging data from the northern South China Sea, the gas hydrate concentration is found to be 3–25% of the pore space at ODP Site 1148 depending on sub-surface depth, and is estimated to be less than values of 5% estimated along seismic profile 0101. Our results suggest that saturation of gas hydrate in the northern South China Sea is higher than that estimated from well resistivity log data in the gas hydrate stability zone, but that free gas is scarce beneath this zone. It is probably the scarcity of free gas that is responsible for the low amplitudes of the BSRs.     

Reservoir characterization of gas hydrate in the Northwestern part of the Ulleung Basin,East Sea

An analysis of 3D seismic data from the northwestern part of the Ulleung Basin, East Sea, revealed that the gas hydrate stability zone (GHSZ) consists of five seismic units separated by regional reflectors. An anticline is present that documents activity of many faults. The seismic indicators of gas hydrate occurrence included bottom simulating reflector (BSR) and acoustic blanking in the gas hydrate occurrence zone (GHOZ). By the analysis of the seismic characteristics and the gradient of the sedimentary strata, the GHOZ was divided into four classes: (1) dipping strata upon strong BSR, (2) dipping strata below strong BSR, (3) parallel strata with acoustic blanking, and (4) parallel strata below weak BSR. Seismic attributes such as reflection strength and instantaneous frequency were computed along the GHOZ. Low reflection strength and high instantaneous frequency were identified above the BSR, indicating the occurrence of gas hydrate. A remarkably high reflection strength and low instantaneous frequency indicated the presence of free gas below the BSR. Considering the distribution of the gas hydrate and free gas, two gas migration processes are suggested: (1) stratigraphic migration through the dipping, permeable strata and (2) structural migration from below the GHSZ along faults.     

Subsurface gas hydrates in the northern Gulf of Mexico

The northern Gulf of Mexico (GoM) has long been a focus area for the study of gas hydrates. Throughout the 1980s and 1990s, work focused on massive gas hydrates deposits that were found to form at and near the seafloor in association with hydrocarbon seeps. However, as global scientific and industrial interest in assessment of the drilling hazards and resource implications of gas hydrate accelerated, focus shifted to understanding the nature and abundance of “buried” gas hydrates. Through 2005, despite the drilling of more than 1200 oil and gas industry wells through the gas hydrate stability zone, published evidence of significant sub-seafloor gas hydrate in the GoM was lacking. A 2005 drilling program by the GoM Gas Hydrate Joint Industry Project (the JIP) provided an initial confirmation of the occurrence of gas hydrates below the GoM seafloor. In 2006, release of data from a 2003 industry well in Alaminos Canyon 818 provided initial documentation of gas hydrate occurrence at high concentrations in sand reservoirs in the GoM. From 2006 to 2008, the JIP facilitated the integration of geophysical and geological data to identify sites prospective for gas hydrate-bearing sands, culminating in the recommendation of numerous drilling targets within four sites spanning a range of typical deepwater settings. Concurrent with, but independent of, the JIP prospecting effort, the Bureau of Ocean Energy Management (BOEM) conducted a preliminary assessment of the GoM gas hydrate petroleum system, resulting in an estimate of 607 trillion cubic meters (21,444 trillion cubic feet) gas-in-place of which roughly one-third occurs at expected high concentrations in sand reservoirs. In 2009, the JIP drilled seven wells at three sites, discovering gas hydrate at high saturation in sand reservoirs in four wells and suspected gas hydrate at low to moderate saturations in two other wells. These results provide an initial confirmation of the complex nature and occurrence of gas hydrate-bearing sands in the GoM, the efficacy of the integrated geological/geophysical prospecting approach used to identify the JIP drilling sites, and the relevance of the 2008 BOEM assessment.     

Seismic imaging of migration pathways by advanced attribute analysis,Alaminos Canyon 21, Gulf of Mexico

Potential accumulations of gas hydrates in Alaminos Canyon Block 21 (AC21) in the Gulf of Mexico are thought to occur in a shallow sand-rich interval, stratigraphically separated from sources of free gas below the base of the gas hydrate stability zone (BGHSZ), by an intervening thick layer of clay- and silt-rich sediments. Availability of sufficient gas charge from depth, in addition to local biogenic sourcing is considered key to the formation of gas hydrates in the GHSZ. Implicitly, a detailed understanding of geometries associated with fault and fracture networks in relation to potential gas migration pathways can provide additional confidence that seismic amplitude anomalies are related to gas hydrate accumulations. Delineation of fault and fracture systems from high resolution seismic data in and below the gas hydrates stability zone (GHSZ) was performed using an automated algorithm—Ant Tracking. The capturing of small-scale detail has particular significance at AC21, revealing a pervasive network of typically small-extent discontinuities, indicative of fracturing, throughout this intervening clay- and silt-rich layer of mass-transport deposits (MTDs). Ant Tracking features appear to correlate, to some extent, with potential gas hydrate accumulations, supporting the concept that fracturing possibly provides migration pathways albeit via a tortuous, complex path. This study demonstrates that the Ant Tracking attribute, in conjunction with detailed seismic interpretation and analysis, can provide valuable evidence of potential gas migration pathways.     

Qualitative assessment of gas hydrate and gas concentrations from the AVO characteristics of the BSR in the Ulleung Basin, East Sea (Japan Sea)

The presence of gas hydrate in the Ulleung Basin, East Sea (Japan Sea), inferred by various seismic indicators, including the widespread bottom-simulating reflector (BSR), has been confirmed by coring and drilling. We applied the standard AVO technique to the BSRs in turbidite/hemipelagic sediments crosscutting the dipping beds and those in debris-flow deposits to qualitatively assess the gas hydrate and gas concentrations. These BSRs are not likely to be affected by thin-bed tuning which can significantly alter the AVO response of the BSR. The BSRs crosscutting the dipping beds in turbidite/hemipelagic sediments are of low-seismic amplitude and characterized by a small positive gradient, indicating a decrease in Poisson’s ratio in the gas-hydrate stability zone (GHSZ), which, in turn, suggests the presence of gas hydrate. The BSRs in debris-flow deposits are characterized by a negative gradient, indicating decreased Poisson’s ratio below the GHSZ, which is likely due to a few percent or greater gas saturations. The increase in the steepness of the AVO gradient and the magnitude of the intercept of the BSRs in debris-flow deposits with increasing seismic amplitude of the BSRs is probably due to an increase in gas saturations, as predicted by AVO model studies based on rock physics. The reflection strength of the BSRs in debris-flow deposits, therefore, can be a qualitative measure of gas saturations below the GHSZ.     

Scale-dependent gas hydrate saturation estimates in sand reservoirs in the Ulleung Basin,East Sea of Korea

Through the use of 2-D and 3-D seismic data, several gas hydrate prospects were identified in the Ulleung Basin, East Sea of Korea and thirteen drill sites were established and logging-while-drilling (LWD) data were acquired from each site in 2010. Sites UBGH2–6 and UBGH2–10 were selected to test a series of high amplitude seismic reflections, possibly from sand reservoirs. LWD logs from the UBGH2–6 well indicate that there are three significant sand reservoirs with varying thickness. Two upper sand reservoirs are water saturated and the lower thinly bedded sand reservoir contains gas hydrate with an average saturation of 13%, as estimated from the P-wave velocity. The well logs at the UBGH2–6 well clearly demonstrated the effect of scale-dependency on gas hydrate saturation estimates. Gas hydrate saturations estimated from the high resolution LWD acquired ring resistivity (vertical resolution of about 5–8 cm) reaches about 90% with an average saturation of 28%, whereas gas hydrate saturations estimated from the low resolution A40L resistivity (vertical resolution of about 120 cm) reaches about 25% with an average saturation of 11%. However, in the UBGH2–10 well, gas hydrate occupies a 5-m thick sand reservoir near 135 mbsf with a maximum saturation of about 60%. In the UBGH2–10 well, the average and a maximum saturation estimated from various well logging tools are comparable, because the bed thickness is larger than the vertical resolution of the various logging tools. High resolution wireline log data further document the role of scale-dependency on gas hydrate calculations.     

Gas hydrate identified in sand-rich inferred sedimentary section using downhole logging and seismic data in Shenhu area,South China Sea

Downhole wireline log (DWL) data was acquired from eight drill sites during China's first gas hydrate drilling expedition (GMGS-1) in 2007. Initial analyses of the acquired well log data suggested that there were no significant gas hydrate occurrences at Site SH4. However, the re-examination of the DWL data from Site SH4 indicated that there are two intervals of high resistivity, which could be indicative of gas hydrate. One interval of high resistivity at depth of 171–175 m below seafloor (mbsf) is associated with a high compressional- wave (P-wave) velocities and low gamma ray log values, which suggests the presence of gas hydrate in a potentially sand-rich (low clay content) sedimentary section. The second high resistivity interval at depth of 175–180 mbsf is associated with low P-wave velocities and low gamma values, which suggests the presence of free gas in a potentially sand-rich (low clay content) sedimentary section. Because the occurrence of free gas is much shallower than the expected from the regional depth of the bottom simulating reflector (BSR), the free gas could be from the dissociation of gas hydrate during drilling or there may be a local anomaly in the depth to the base of the gas hydrate stability zone. In order to determine whether the low P-wave velocity with high resistivity is caused by in-situ free gas or dissociated free gas from the gas hydrate, the surface seismic data were also used in this analysis. The log analysis incorporating the surface seismic data through the construction of synthetic seismograms using various models indicated the presence of free gas directly in contact with an overlying gas hydrate-bearing section. The occurrence of the anomalous base of gas hydrate stability at Site SH4 could be caused by a local heat flow conditions. This paper documents the first observation of gas hydrate in what is believed to be a sand-rich sediment in Shenhu area of the South China Sea.     

Qualitative assessment of gas hydrate and gas concentrations from the AVO characteristics of the BSR in the Ulleung Basin,East Sea (Japan Sea)

The presence of gas hydrate in the Ulleung Basin, East Sea (Japan Sea), inferred by various seismic indicators, including the widespread bottom-simulating reflector (BSR), has been confirmed by coring and drilling. We applied the standard AVO technique to the BSRs in turbidite/hemipelagic sediments crosscutting the dipping beds and those in debris-flow deposits to qualitatively assess the gas hydrate and gas concentrations. These BSRs are not likely to be affected by thin-bed tuning which can significantly alter the AVO response of the BSR. The BSRs crosscutting the dipping beds in turbidite/hemipelagic sediments are of low-seismic amplitude and characterized by a small positive gradient, indicating a decrease in Poisson’s ratio in the gas-hydrate stability zone (GHSZ), which, in turn, suggests the presence of gas hydrate. The BSRs in debris-flow deposits are characterized by a negative gradient, indicating decreased Poisson’s ratio below the GHSZ, which is likely due to a few percent or greater gas saturations. The increase in the steepness of the AVO gradient and the magnitude of the intercept of the BSRs in debris-flow deposits with increasing seismic amplitude of the BSRs is probably due to an increase in gas saturations, as predicted by AVO model studies based on rock physics. The reflection strength of the BSRs in debris-flow deposits, therefore, can be a qualitative measure of gas saturations below the GHSZ.     

An enigmatic strong reflector on subbottom profiler records from the Black Sea—the top of shallow gas hydrate deposits

An anomalous strong, shallow reflector has been observed in several deep-tow subbottom profiler records in a region of the northern Black Sea characterised by seafloor fluid seeps, mud volcanoes, and the occurrence of gas hydrates. The digital data were processed using adapted seismic processing methods. Synthetic seismograms created to model representative traces from the observed profiles require anomalous alternations of acoustic properties in the upper sediments which can best be explained by interbedded layers of normal sediments and sediments with gas hydrates. The enigmatic strong reflector can be explained by constructive interference of reflections from five of these thin layers. It is proposed that the uppermost region of the gas hydrate stability zone here is represented by thinning layers of interbedded gas hydrates or layers with lower concentrations of gas hydrates.     

Fluid flow and methane occurrences in the Disko Bugt area offshore West Greenland: indications for gas hydrates?

The present study is the first to directly address the issue of gas hydrates offshore West Greenland, where numerous occurrences of shallow hydrocarbons have been documented in the vicinity of Disko Bugt (Bay). Furthermore, decomposing gas hydrate has been implied to explain seabed features in this climate-sensitive area. The study is based on archive data and new (2011, 2012) shallow seismic and sediment core data. Archive seismic records crossing an elongated depression (20×35 km large, 575 m deep) on the inner shelf west of Disko Bugt (Bay) show a bottom simulating reflector (BSR) within faulted Mesozoic strata, consistent with the occurrence of gas hydrates. Moreover, the more recently acquired shallow seismic data reveal gas/fluid-related features in the overlying sediments, and geochemical data point to methane migration from a deeper-lying petroleum system. By contrast, hydrocarbon signatures within faulted Mesozoic strata below the strait known as the Vaigat can be inferred on archive seismics, but no BSR was visible. New seismic data provide evidence of various gas/fluid-releasing features in the overlying sediments. Flares were detected by the echo-sounder in July 2012, and cores contained ikaite and showed gas-releasing cracks and bubbles, all pointing to ongoing methane seepage in the strait. Observed seabed mounds also sustain gas seepages. For areas where crystalline bedrock is covered only by Pleistocene–Holocene deposits, methane was found only in the Egedesminde Dyb (Trough). There was a strong increase in methane concentration with depth, but no free gas. This is likely due to the formation of gas hydrate and the limited thickness of the sediment infill. Seabed depressions off Ilulissat Isfjord (Icefjord) previously inferred to express ongoing gas release from decomposing gas hydrate show no evidence of gas seepage, and are more likely a result of neo-tectonism.     

Multiple seismic attribute analyses for determination of bottom simulating reflector of gas hydrate seismic data in the Ulleung Basin of Korea

The bottom simulating reflector (BSR), the boundary between the gas hydrate and the free gas zone, is considered to be the most common evidence in seismic data analysis for gas hydrate exploration. Multiple seismic attribute analyses of reflectivity and acoustic impedance from the post-stack deconvolution and complex analysis of instantaneous attribute properties including the amplitude envelope, instantaneous frequency, phase, and first derivative of the amplitude of seismic data have been used to effectively confirm the existence of a BSR as the base of gas hydrate stability zone. In this paper, we consider individual seismic attribute analysis and integrate the results of those attributes to locate the position of the BSR. The outputs from conventional seismic data processing of the gas hydrate data set in the Ulleung Basin were used as inputs for multiple analyses. Applying multiple attribute analyses to the individual seismic traces showed that the identical anomalies found in two-way travel time (TWT) between 3.1 and 3.2 s from the results of complex analyses and l ₁ norm deconvolution indicated the location of the BSR.     

High-resolution well-log derived dielectric properties of gas-hydrate-bearing sediments, Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

A dielectric logging tool, electromagnetic propagation tool (EPT), was deployed in 2007 in the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well (Mount Elbert Well), North Slope, Alaska. The measured dielectric properties in the Mount Elbert well, combined with density log measurements, result in a vertical high-resolution (cm-scale) estimate of gas hydrate saturation. Two hydrate-bearing sand reservoirs about 20 m thick were identified using the EPT log and exhibited gas-hydrate saturation estimates ranging from 45% to 85%. In hydrate-bearing zones where variation of hole size and oil-based mud invasion are minimal, EPT-based gas hydrate saturation estimates on average agree well with lower vertical resolution estimates from the nuclear magnetic resonance logs; however, saturation and porosity estimates based on EPT logs are not reliable in intervals with substantial variations in borehole diameter and oil-based invasion.EPT log interpretation reveals many thin-bedded layers at various depths, both above and below the thick continuous hydrate occurrences, which range from 30-cm to about 1-m thick. Such thin layers are not indicated in other well logs, or from the visual observation of core, with the exception of the image log recorded by the oil-base microimager. We also observe that EPT dielectric measurements can be used to accurately detect fine-scale changes in lithology and pore fluid properties of hydrate-bearing sediments where variation of hole size is minimal. EPT measurements may thus provide high-resolution in-situ hydrate saturation estimates for comparison and calibration with laboratory analysis.     

A seismic study to investigate the prospect of gas hydrate in Mahanadi deep water basin,northeastern continental margin of India

The presence of gas hydrates, one of the new alternative energy resources for the future, along the Indian continental margins has been inferred mainly from bottom simulating reflectors (BSR) and the gas stability zone thickness mapping. Gas hydrate reserves in Krishna Godawari Basin have been established with the help of gas-hydrate related proxies inferred from multidisciplinary investigations. In the present study, an analysis of 3D seismic data of nearly 3,420 km² area of Mahanadi deep water basin was performed in search of seismic proxies related with the existence of natural gas hydrate in the region. Analysis depicts the presence of BSR-like features over a large areal extent of nearly 250 km² in the central western part of the basin, which exhibit all characteristics of a classical BSR associated with gas hydrate accumulation in a region. The observed BSR is present in a specific area restricted to a structural low at the Neogene level. The coherency inversion of pre-stack time migration (PSTM) gathers shows definite inversion of interval velocity across the BSR interface which indicates hydrate bearing sediments overlying the free gas bearing sediments. The amplitude versus offset analysis of PSTM gathers shows increase of amplitude with offset, a common trend as observed in BSR associated with gas hydrate accumulation. Results suggest the possibility of gas hydrate accumulation in the central part of the basin specifically in the area of structural low at the Neogene level. These results would serve as preliminary information for selecting prospective gas hydrate accumulation areas for further integrated or individual study from geophysical, geological, geochemical and microbiological perspectives for confirmation of gas hydrate reserves in the area. Further, on the basis of these results it is envisaged that biogenic gas might have been generated in the region which under suitable temperature and pressure conditions might have been transformed into the gas hydrates, and therefore, an integrated study comprising geophysical, geological, geochemical and microbiological data is suggested to establish the gas hydrate reserves in Mahanadi deep water basin.