Insight into sediment transport processes on saline rangeland hillslopes using three‐dimensional soil microtopography changes

In arid and semi‐arid rangeland environments, an accurate understanding of runoff generation and sediment transport processes is key to developing effective management actions and addressing ecosystem response to changes. Yet, many primary processes (namely sheet and splash and concentrated flow erosion, as well as deposition) are still poorly understood due to a historic lack of measurement techniques capable of parsing total soil loss into these primary processes. Current knowledge gaps can be addressed by combining traditional erosion and runoff measurement techniques with image‐based three‐dimensional (3D) soil surface reconstructions. In this study, data (hydrology, erosion and high‐resolution surface microtopography changes) from rainfall simulation experiments on 24 plots in saline rangelands communities of the Upper Colorado River Basin were used to improve understanding on various sediment transport processes. A series of surface change metrics were developed to quantify and characterize various erosion and transport processes (e.g. plot‐wide versus concentrated flow detachment and deposition) and were related to hydrology and biotic and abiotic land surface characteristics. In general, erosivity controlled detachment and transport processes while factors modulating surface roughness such as vegetation controlled deposition. The extent of the channel network was a positive function of slope, discharge and vegetation. Vegetation may deflect runoff in many flow paths but promoted deposition. From a management perspective, this study suggests that effective runoff soil and salt load reduction strategies should aim to promote deposition of transported sediments rather than reducing detachment which might not be feasible in these resource‐limited environments. Copyright © 2016 John Wiley & Sons, Ltd.     

PHYSICAL PROCESS BASED SOIL EROSION MODEL IN A SMALL WATERSHED IN THE HILLY LOESS REGION

ＰＨＹＳＩＣＡＬＰＲＯＣＥＳＳＢＡＳＥＤＳＯＩＬＥＲＯＳＩＯＮＭＯＤＥＬＩＮＡＳＭＡＬＬＷＡＴＥＲＳＨＥＤＩＮＴＨＥＨＩＬＬＹＬＯＥＳＳＲＥＧＩＯＮ１ＣＡＩＱｉａｎｇｇｕｏ２ＡＢＳＴＲＡＣＴＡｐｈｙｓｉｃａｌｐｒｏｃｅｓｂａｓｅｄｐｅｒｓｔｏｒｍ...     

Water flux and sediment transport within a forested landscape: the role of connectivity,subsurface flow,and slope length scale on transport mechanism

The connectivity and upscaling of overland runoff and sediment transport are important issues in hillslope hydrology to identify water flux and sediment transport within landscape. These processes are highly variable in time and space with regard to their interactions with vegetation and soil surface conditions. The generation of overland runoff and its spatial connectivity were examined along a slope to determine the variations in the transport mechanism of runoff and soil particles by rain splash and overland runoff. Field experiments were conducted by erosion plots on a steep hillslope at lengths of 5, 10, and 15 m. The overland runoff connectivity and flow transport distance decreased with the slope length, while spatial variability of infiltration increased significantly with the slope length. Observation of subsurface flow revealed that surface soil and litter layer could have important role in water transport. However, the surface soil water content and water flux transport along the slope was highly variable for different storm events; the variability was related to the complexity of the system, mainly by way of the initial wetness conditions and infiltration characteristics. Only net rain‐splashed soil was measurable, but examination of the water flux, overland runoff and sediment transport connectivity, characteristics of sheetwash, and the variability in spatial infiltration indicated an increase in the contribution of the rain splash transport mechanism along the slope. Copyright © 2013 John Wiley & Sons, Ltd.     

Modelling sediment trapping in vegetative filter strips on steep slopes

The slope effects on sediment trapping process in vegetative filter strips (VFS) are usually neglected in current modelling practices for VFS operation, which hamper the VFS design and performance evaluation, especially on steep slopes. To fill the knowledge gap, 12 laboratory experiments of sediment trapping in VFS were conducted with three different inflow discharge (80, 100, and 120 ml s⁻¹) and four slope angles (5,10, 15, and 20°). The experimental results show that, on steep slopes (10, 15, and 20°), a part of trapped sediment particles in VFS can be eroded again and then dragged to the downstream as bed load, whilst they do not move on gentle slope (5°). To describe the complex processes, a simple and effective modelling framework was developed for sloped VFS by coupling the slope infiltration, runoff, and modified sediment transport model. The model was tested against the experimental results and good agreements between the modelled and observed results were found in both runoff and sediment transport processes for all cases. On steep slopes, the sediment trapping performance of VFS decreases significantly because the erosion of deposited sediment particles can account for more than 60% of the sediment load in the outflow. The slope effect on sediment trapping efficiency of VFS varies greatly with soil, VFS, and slope properties. The model was compared with previous sediment transport equation and found that both methods can satisfactorily predict the sediment trapping of VFS on gentle slopes, but previous sediment transport equation is likely to overestimate the sediment trapping efficiency in VFS on steep slopes. This model is expected to provide a more realistic and accurate method for predicting runoff and sediment reduction in VFS on sloping surfaces.     

Effects of Caragana Korshinskii Kom. Cover on runoff,sediment yield and nitrogen loss

Soil erosion is serious in the Loess Plateau of China. Deposition of the eroded sediment in lakes or rivers may lead to eutrophication, because the sediment carries a lot of nutrients. Field experiments were conducted to study soil erosion and loss of nitrogen (N) from a 15o hillslope with 30% (low) or 80% (high) coverage of the shrub Caragana korshinskii Kom. A bare soil plot was used for the comparison. The results showed that Caragana korshinskii cover significantly reduced runoff and soil erosion. In comparison to the bare soil plot, the vegetation covered plots had about 20% less runoff and 65% less sediment. In general, the concentration of N in both runoff water and the eroded sediment decreased with time and approached a steady value. However, the species of nitrate nitrogen (NO3) was exceptional which increased with time slightly. The soil erosion caused an N loss of about 250 mg/m2 for the bare soil plot, the low coverage of Caragana korshinskii reduced the N loss by 20% and the high coverage of Caragana korshinskii reduced the N loss by 40%. Moreover, the amount of total N in eroded sediment was 2 to 3 times higher than the value in runoff water. In the total N loss, the organic N was about 75-80%. Nevertheless, inorganic N in runoff water was 5 to 10 times higher than the value in eroded sediment. The species of NO3 was obviously higher than the species of ammonium nitrogen (NH4). NO3 was the main species of inorganic N loss and was about two thirds of total. The organic N was the main species of N in the eroded sediment.     

Time-dependency of runoff velocity and erosion the effect of the initial soil moisture profile

The paper reports on experiments carried out to evaluate the effect of the initial soil moisture profile on temporal variations in runoff erosion rate. The moisture profile was varied by applying infrared heating to the soil sample surface over various time periods, while runoff erosivity was varied by varying the slope of the flume. The experiment confirms that dry loamy soils are very erodible: on a slope length of only 4.3 m long sediment concentrations are near transporting capacity in case of a dry soil sample. It appears that temporal variations in sediment concentrations can be well simulated using a simple relationship between runoff erosion resistance and initial soil moisture content, thereby implicitly assuming that the effect of initial moisture content is persistent over the whole duration of the experiment. The implications of these findings with respect to the modelling of sediment output from larger catchments and the design of experiments on rill erodibility are discussed. The experiments also show that, under the present circumstances, mean velocities in the rills appear to be independent of slope. This finding may be of importance with respect to overland flow routing and deterministic erosion modelling.     

A methodology to study rain splash and wash processes under natural rainfall

The complex interactions between rainfall‐driven erosion processes and rainfall characteristics, slope gradient, soil treatment and soil surface processes are not very well understood. A combination of experiments under natural rainfall and a consistent physical theory for their interpretation is needed to shed more light on the underlying processes. The present study demonstrates such a methodology. An experimental device employed earlier in laboratory studies was used to measure downslope rain splash and ‘splash‐creep’, lateral splash, upslope splash and rainfall‐driven runoff transport (wash) from a highly aggregated clay‐rich oxisol exposed to natural rainfall in West Java, Indonesia. Two series of measurements were made: the first with the soil surface at angles of 0°, 5°, 15° and 40°; and the second all at an angle of 5° but with different tillage and mulching treatments. A number of rainfall erosivity indices were calculated from rainfall intensity measurements and compared with measured transport components. Overall storm kinetic energy correlated reasonably well with sediment transport, but much better agreement was obtained when a threshold rainfall intensity (20 mm h^?1) was introduced. Rain splash transport measurements were interpreted using a recently developed theory relating detachment to sediment transport. Furthermore, a conceptually sound yet simple wash transport model is advanced that satisfactorily predicted observed washed sediment concentrations. The lack of replication precluded rigorous assessment of the effect of slope and soil treatment on erosion processes, but some general conclusions could still be drawn. The results stress the importance of experiments under conditions of natural rainfall. Copyright © 2002 John Wiley & Sons, Ltd.     

Effects of different spatial distributions of physical soil crusts on runoff and erosion on the Loess Plateau in China

The response of runoff and erosion to soil crusts has been extensively investigated in recent decades. However, there have been few attempts to look at the effects of spatial configuration of different soil crusts on erosion processes. Here we investigated the effects of different spatial distributions of physical soil crusts on runoff and erosion in the semi‐arid Loess Plateau region. Soil boxes (1.5 m long × 0.2 m wide) were set to a slope of 17.6% (10°) and simulated rainfall of 120 mm h^?1 (60 minutes). The runoff generation and erosion rates were determined for three crust area ratios (depositional crust for 20%, 33%, and 50% of the total slope) and five spatial distribution patterns (depositional crust on the lower, lower‐middle, middle, mid‐upper, and upper slope) of soil crusts. The reduction in sediment loss (‘sediment reduction’) was calculated to evaluate the effects of different spatial distributions of soil crusts on erosion. Sediment yield was influenced by the area ratio and spatial position of different soil crusts. The runoff rate reached a steady state after an initial trend of unsteadily increasing with increasing rainfall duration. Sediment yield was controlled by detachment limitation and then transport limitation under rainfall. The shifting time of erosion from a transport to detachment‐limiting regime decreased with increasing area of depositional crust. No significant differences were observed in the total runoff among treatments, while the total sediment yield varied under different spatial distributions. At the same area ratio, total sediment yield was the largest when the depositional crust was on the upper slope, and it was smallest when the crust was deposited on the lower slope. The sediment reduction of structural crust (42.5–66.5%) was greater than that of depositional crust (16.7–34.3%). These results provide a mechanistic understanding of how different spatial distributions of soil crusts affect runoff and sediment production. Copyright © 2017 John Wiley & Sons, Ltd.     

DEM-based numerical modelling of runoff and soil erosion processes in the hilly–gully loess regions

For sake of improving our current understanding on soil erosion processes in the hilly–gully loess regions of the middle Yellow River basin in China, a digital elevation model (DEM)-based runoff and sediment processes simulating model was developed. Infiltration excess runoff theory was used to describe the runoff generation process while a kinematic wave equation was solved using the finite-difference technique to simulate concentration processes on hillslopes. The soil erosion processes were modelled using the particular characteristics of loess slope, gully slope, and groove to characterize the unique features of steep hillslopes and a large variety of gullies based on a number of experiments. The constructed model was calibrated and verified in the Chabagou catchment, located in the middle Yellow River of China and dominated by an extreme soil-erosion rate. Moreover, spatio-temporal characterization of the soil erosion processes in small catchments and in-depth analysis between discharge and sediment concentration for the hyper-concentrated flows were addressed in detail. Thereafter, the calibrated model was applied to the Xingzihe catchment, which is dominated by similar soil erosion processes in the Yellow River basin. Results indicate that the model is capable of simulating runoff and soil erosion processes in such hilly–gully loess regions. The developed model are expected to contribute to further understanding of runoff generation and soil erosion processes in small catchments characterized by steep hillslopes, a large variety of gullies, and hyper-concentrated flow, and will be beneficial to water and soil conservation planning and management for catchments dealing with serious water and soil loss in the Loess Plateau.     

Time‐lapse video observation of erosion processes on the Black Marls badlands in the Southern Alps,France

In order to clarify the erosion processes on a marly bare slope in the Southern Alps, the erosion processes in a steep and erodible slope composed of the Black Marls Formation were observed by a time‐lapse video camera. The observations revealed that miniature debris flows (MDFs) occurred at the time of the rainfall‐runoff event in which the most severe erosion took place in the whole observation period of 3 months. Analysis of the camera images showed some characteristics of the MDFs, and these are discussed in the context of real rainfall‐runoff phenomena observed at the outlet of a small experimental basin including the visually observed slope. The following results were obtained. (1) A rough estimation of the total amount of sediment discharge by the MDFs showed that it was not negligible quantitatively. (2) The MDFs occurred only during the rising limb of the hydrograph during 6 minutes. (3) Based on this observation and a review of the literature, in a very steep and highly erodible slope, MDFs or similar phenomena might play an important role in the erosion and transport processes. Copyright © 2008 John Wiley and Sons, Ltd.     

Field measurements of interrill erosion under ­different slopes and plot sizes

Despite numerous studies, the effect of slope on interrill erosion is not clearly established. Several interactions exist between erosion parameters that are not taken into account under experimental laboratory measurements and results need to be validated in the field. The influence of slope steepness (2 to 8 per cent) on soil loss for a crusted interrill area and the detachment and transport processes involved in the interaction between slope, rain characteristics and plot size were investigated. Sediment discharge and runoff rates were measured in bounded plots (1 m2 and 10 m2) under natural and simulated rainfall, allowing the analysis of a combination of detachment and transport processes at various scales in the field. Runoff rate increased from 20 to 90 per cent with increasing slope and rain intensity for both plot sizes, whereas sediment concentration increased from 2 to 6 g l−1 with increasing slope only for the 10 m2 plots. At the 1 m2 scale, erosion was transport‐limited due to the reduced rain‐impacted flow. Interactions between slope angle and rain intensity were observed for detachment and transport processes in interrill erosion. Results show the importance of an adapted experimental set‐up to get reference data for interrill erosion model development and validation. Copyright © 2000 John Wiley & Sons, Ltd.     

The effect of soil type,meteorological forcing and slope gradient on the simulation of internal erosion processes at the local scale

Numerical simulation experiments of water erosion at the local scale (20 × 5 m) using a process‐based model [Plot Soil Erosion Model_2D (PSEM_2D)] were carried out to test the effects of various environmental factors (soil type, meteorological forcing and slope gradient) on the runoff and erosion response and to determine the dominant processes that control the sediment yield at various slope lengths. The selected environmental factors corresponded to conditions for which the model had been fully tested beforehand. The use of a Green and Ampt model for infiltration explained the dominant role played by rainfall intensity in the runoff response. Sediment yield at the outlet of the simulated area was correlated positively with rainfall intensity and slope gradient, but was less sensitive to soil type. The relationship between sediment yield (soil loss per unit area) and slope length was greatly influenced by all environmental factors, but there was a general tendency towards higher sediment yield when the slope was longer. Contribution of rainfall erosion to gross erosion was dominant for all surfaces with slope lengths ranging from 4 to 20 m. The highest sediment yields corresponded to cases where flow erosion was activated. An increase in slope gradient resulted in flow detachment starting upstream. Sediment exported at the outlet of the simulated area came predominantly from the zone located near the outlet. The microrelief helped in the development of a rill network that controlled both the ratio between rainfall and flow erosion and the relationship between sediment yield and slope length. Copyright © 2010 John Wiley & Sons, Ltd.     

One-dimensional morphodynamic model for retrogressive erosion based on a sediment entrainment theory at high flow velocity

Retrogressive erosion is a high-speed erosion process that usually occurs during the rapid release of stored water in reservoirs built on sandy rivers.Retrogressive erosion has been utilized in the practice of reservoir sedimentation control,but accurate prediction of the bed deformation process by numerical models has rarely been reported.The current study presents a one-dimensional morphodynamic model for simulating the evolution process of retrogressive erosion induced by high-velocity flows on steep slopes.The governing equations apply a Cartesian coordinate system with a vertically oriented z axis.The bed surface gradient and friction terms in the flow equations include correction factors to take account of the effects of high slope on flow movement.The net vertical sediment flux term in the sediment transport and bed deformation equations is calculated using an equation of erosion velocity.Particularly,this equation is based on an empirical relation between the sediment entrainment rate and the Shields parameter in contrast to the traditional sediment transport capacity,and the critical Shields parameter is modified by taking into account the permeability of the sediment layer and the stability of particles on a slope.The feedback of scoured sediment on the flow movement is considered by additional terms in the governing equations.Flume experiments of retrogressive erosion in literature were simulated to validate the model.The temporal variations of the longitudinal profiles of the free surface and channel bed and the sediment transport rate were well predicted.The algorithm calculating sediment entrainment in the proposed model also was validated for an experiment measuring entrainment rate from the literature.More importantly,it was found that the morphodynamic model using the sediment transport capacity equation predicts the trend of cumulative erosion contrary to the measurements,while results of the proposed model can follow a similar trend with the observed data in the retrogressive erosion process.     

Physically based modelling of sediment generation and transport under a large rainfall simulator

A series of large rainfall simulator experiments was conducted in 2002 and 2003 on a small plot located in an experimental catchment in the North Island of New Zealand. These experiments measured both runoff and sediment transport under carefully controlled conditions. A physically based hydrological modelling system (SHETRAN) was then applied to reproduce the observed hydrographs and sedigraphs. SHETRAN uses physically based equations to represent flow and sediment transport, and two erodibility coefficients to model detachment of soil particles by raindrop erosion and overland flow erosion. The rate of raindrop erosion also depended on the amount of bare ground under the simulator; this was estimated before each experiment. These erodibility coefficients were calibrated systematically for summer and winter experiments separately, and lower values were obtained for the summer experiments. Earlier studies using small rainfall simulators in the vicinity of the plot also found the soil to be less erodible in summer and autumn. Limited validation of model parameters was carried out using results from a series of autumn experiments. The modelled suspended sediment load was also sensitive to parameters controlling the generation of runoff from the rainfall simulator plot; therefore, we found that accurate runoff predictions were important for the sediment predictions, especially from the experiments where the pasture cover was good and overland flow erosion was the dominant mechanism. The rainfall simulator experiments showed that the mass of suspended sediment increased post‐grazing, and according to the model this was due to raindrop detachment. The results indicated that grazing cattle or sheep on steeply sloping hill‐country paddocks should be carefully managed, especially in winter, to limit the transport of suspended sediment into watercourses. Copyright © 2006 John Wiley & Sons, Ltd.     

Spatial simulation of forest road effects on hydrology and soil erosion after a wildfire

Post-fire catchment and water utility managers throughout the world use predictive models to estimate potential erosion risks to aid in evaluating downstream impacts of increased runoff and erosion, and to target critical areas within a fire for applying mitigation practices. Erosion prediction can be complicated by forest road networks. Using novel GIS technology and soil erosion modelling, this study evaluated the effect of roads on surface runoff, erosion and sediment yields following a wildfire and determined that the predictive models were providing reasonable results. The GeoWEPP model was used to simulate onsite erosion and offsite sediment delivery before and after fire disturbance using a 2-m resolution DEM as the terrain layer. Erosion rates in excess of 4 Mg ha⁻¹ year⁻¹ were predicted mainly from steep moderate and high severity burn areas. Roads influenced surface runoff flow path distributions and sub-catchment delineations, affecting the spatial distribution of sediment detachment and transport. Roads tended to reduce estimated erosion on slopes below the roads but increases in erosion rates were estimated for road fillslopes. Estimated deposition amounts on roads and in sediment basins were similar to measured amounts. The results confirm that road prisms, culverts and road ditches influence sedimentation processes after wildfire, and they present opportunities to detain eroded sediments.     

Tracing sediment redistribution across a break in slope using rare earth elements

Experimentally determined spatial patterns of soil redistribution across a break in slope derived using 10 rare earth element (REE) oxides as sediment tracers are presented. An erosion experiment was conducted using simulated rainfall within a laboratory slope model measuring 2·5 m wide by 6 m long with a gradient of 15° declining to 2°. Soil was tagged with multiple REE and placed in different locations over the slope and at the end of the experiment REE concentrations were measured in samples collected spatially. A new method was developed to quantify the erosion and deposition depths spatially, the relative source contributions to deposited sediment and the sediment transport distances. Particle‐size selectivity over an area of net deposition was also investigated, by combining downslope changes in particle‐size distributions with changes in sediment REE composition within a flow pathway. During the experiment, the surface morphology evolved through upslope propagation of rill headcuts, which gradually incised the different REE‐tagged zones and led to sediment deposition at the break in slope and the development of a fan extending over the shallow slope segment. The spatial patterns in REE concentrations, the derived erosion and deposition depths, the relative source contributions to deposition zones and the sediment transport distances, corroborate the morphological observations and demonstrate the potential of using REE for quantifying sediment transport processes. Copyright © 2010 John Wiley & Sons, Ltd.     

Sediment transport capacity and erosion processes: model concepts and reality

Sediment transport capacity, T_c, defined as the maximum amount of sediment that a flow can carry, is the basic concept in determining detachment and deposition processes in current process-based erosion models. Although defined conceptually and used extensively in modelling erosion, T_c was rarely measured. Recently, a series of laboratory studies designed to quantify effects of surface hydrologic conditions on erosion processes produced data sets feasible to evaluate the concept of T_c. A dual-box system, consisting of 1·8 m long sediment feeder box and a 5 m long test box, was used. Depending on the relative magnitudes of sediment delivery from feeder and test boxes, five scenarios are proposed ranging from deposition-dominated to transport-dominated sediment regimes. Results showed that at 5 per cent slope under seepage or 10 per cent slope under drainage conditions, the runoff from the feeder box caused in the additional sediment transport in the test box, indicating a transport-dominated sediment regime. At 5 per cent slope under drainage conditions, deposition occurred at low rainfall intensities. Increases in slope steepness, rainfall intensity and soil erodibility shifted the dominant erosion process from deposition to transport. Erosion process concepts from the Meyer–Wishmeier, Foster–Meyer and Rose models were compared with the experimental data, and the Rose model was found to best describe processes occurring during rain. A process-based erosion model needs to have components that can represent surface conditions and physical processes and their dynamic interactions. Copyright © 1999 John Wiley & Sons, Ltd.     

The European Soil Erosion Model (EUROSEM): a dynamic approach for predicting sediment transport from fields and small catchments

The European Soil Erosion Model (EUROSEM) is a dynamic distributed model, able to simulate sediment transport, erosion and deposition over the land surface by rill and interill processes in single storms for both individual fields and small catchments. Model output includes total runoff, total soil loss, the storm hydrograph and storm sediment graph. Compared with other erosion models, EUROSEM has explicit simulation of interill and rill flow; plant cover effects on interception and rainfall energy; rock fragment (stoniness) effects on infiltration, flow velocity and splash erosion; and changes in the shape and size of rill channels as a result of erosion and deposition. The transport capacity of runoff is modelled using relationships based on over 500 experimental observations of shallow surface flows. EUROSEM can be applied to smooth slope planes without rills, rilled surfaces and surfaces with furrows. Examples are given of model output and of the unique capabilities of dynamic erosion modelling in general. © 1998 John Wiley & Sons, Ltd.     

RILL EROSION PROCESS AND RILL FLOW HYDRAULIC PARAMETERS

In the rill erosion process, run-on water and sediment from upslope areas, and rill flow hydraulic parameters have significant effects on sediment detachment and transport. However, there is a lack of data to quantify the effects of run-on water and sediment and rill flow hydraulic parameters on rill erosion process at steep hillslopes, especially in the Loess Plateau of China. A dual-box system, consisting of a 2-m-long feeder box and a 5-m-long test box with 26.8% slope gradient was used to quantify the effects of upslope runoff and sediment, and of rill flow hydraulic parameters on the rill erosion process. The results showed that detachment-transport was dominated in rill erosion processes; upslope runoff always caused the net rill detachment at the downslope rill flow channel, and the net rill detachment caused by upslope runoff increased with a decrease of runoff sediment concentration from the feeder box or an increase of rainfall intensity. Upslope runoff discharging into the rill flow channel or an increase of rainfall intensity caused the rill flow to shift from a stratum flow into a turbulent flow. Upslope runoff had an important effect on rill flow hydraulic parameters, such as rill flow velocity, hydraulic radius, Reynolds number, Froude number and the Darcy-Weisbach resistance coefficient. The net rill detachment caused by upslope runoff increased as the relative increments of rill flow velocity, Reynolds number and Froude number caused by upslope runoff increased. In contrast, the net rill detachment decreased with an increase of the relative decrement of the Darcy-Weisbach resistance coefficient caused by upslope runoff. These findings will help to improve the understanding of the effects of run-on water and sediment on the erosion process and to find control strategies to minimize the impact of run-on water.     

Sediment production and yield from an alluvial gully in northern Queensland,Australia

Sediment production, transport and yield were quantified over various timescales in response to rainfall and runoff within an alluvial gully (7 · 8 ha), which erodes into dispersible sodic soils of a small floodplain catchment (33 ha) along the Mitchell River, northern Australia. Historical air photographs and recent global positioning system (GPS) surveys and LiDAR data documented linear increases in gully area and volume, indicating that sediment supply has been relatively consistent over the historic period. Daily time lapse photography of scarp retreat rates and internal erosion processes also demonstrated that erosion from rainfall and runoff consistently supplied fine washload (< 63 µm) sediment in addition to coarse lags of sand bed material. Empirical measurements of suspended sediment concentrations (10 000 to >100 000 mg/L) and sediment yields (89 to 363 t/ha/yr) were high for both Australian and world data. Total sediment yield estimated from empirical washload and theoretical bed material load was dominated by fine washload (< 63 µm). A lack of hysteresis in suspended sediment rating curves, scarp retreat and sediment yield correlated to rainfall input, and an equilibrium channel outlet slope supported the hypothesis that partially or fully transport‐limited conditions predominated along the alluvial gully outlet channel. This is in contrast to sediment supply‐limited conditions on uneroded floodplains above gully head scarps. While empirical data presented here can support future modelling efforts to predict suspended sediment concentration and yield under the transport limiting situations, additional field data will also be needed to better quantify sediment erosion and transport rates and processes in alluvial gullies at a variety of spatial and temporal scales. Copyright © 2013 John Wiley & Sons, Ltd.