A study on lower fatty acids and polyethylene glycols adsorption on activated carbon

The dependence of the Freundlich constants on molecular weight of members of a homologous series was studied using lower fatty acids and polyethylene glycols. The adsorption was conducted on powdered activated carbon Carboraffin at 18±1°C. The obtained results may be summarized as follows: The adsorption of both fatty acids and polyethylene glycols may be satisfactorily described by the Freundlich adsorption isotherm. The constant K from the Freundlich equation increases with increasing molecular weight of both fatty acids and polyethylene glycols. The exponent n was found to be practically constant for fatty acids but to decrease with increasing molecular weight of polyethylene glycols. The pH of solution exerts an influence upon the adsorption of fatty acids and has no influence upon the adsorption of polyethylene glycols. The amenability of fatty acids to the adsorption decreases with increasing pH. No adsorption may be expected above pH of 8.2.     

Adsorption of Phosphate by Biomass Char Deriving from Fast Pyrolysis of Biomass Waste

Biomass char (BC) deriving from fast pyrolysis of biomass was a potential adsorption material due to its relative high fixed‐carbon content and the inherent porous structures. Adsorption of phosphate from aqueous solution by BC was investigated in this paper. The results showed that the adsorption capacity of BC was dependent on pyrolysis conditions, such as temperature and holding time. The maximum adsorption capacity for phosphate was approximately 15.11 mg g^?1 at 298 K. The pseudo‐second order model of the adsorption kinetics indicated that the adsorption process was complex and several mechanisms were involved. Equilibrium isotherm was satisfactorily followed the Freundlich isotherm model. The K_F value in Freundlich equation gradually increased with elevating temperature. Moreover, the thermodynamic constants: ΔG⁰, ΔH⁰, and ΔS⁰ were evaluated as ?6.49 kJ mol^?1 (at 298 K), 13.41 kJ mol^?1, and 66.70 J mol^?1 K^?1, respectively. Phosphate adsorption onto BC was spontaneous and endothermic. As a waste, BC was a potentially attractive adsorbent for phosphate removal from aqueous solution with low cost and high capability.     

Isotherm Study of Phosphorus Uptake from Aqueous Solution Using Aluminum Oxide

Aluminum oxide, which could be an alternative filter media for phosphorus uptake from aqueous solution, was selected as an adsorbent for the isotherm study of phosphorus uptake from aqueous solution. Batch method was adopted to investigate the adsorption behavior of phosphorus onto aluminum oxide. The Langmuir, Freundlich, and Redlich–Peterson isotherms were used to analyze the experimental data by both the linear and nonlinear regression methods. The adsorption experiment was conducted at various temperatures, to choose the appropriate method and obtain the creditable adsorption parameters for phosphorus uptake studies. The results indicated that the nonlinear regression method might be a better way to compare the best‐fitting isotherm and obtain the parameters for the adsorption of phosphorus onto aluminum oxide. Both the Redlich–Peterson and the Freundlich isotherms have high coefficients of determination for the adsorption of phosphorus onto aluminum oxide at various temperatures. In addition, a new relationship between the Redlich–Peterson and the Freundlich isotherm parameters was presented.     

Removal of Chromium from Synthetic Effluent using Nymphaea rubra

In the present work, biosorption of Cr(VI) by Nymphaea rubra was investigated in batch studies. Batch experiments were conducted to study the effect of initial sorbent dosage, solution pH and initial Cr(VI) concentration. The results showed that the equilibrium uptake capacity was increased with decrease in biomass dosage. The Cr(VI) removal was influenced by the initial chromium compound concentration. Langmuir and Freundlich adsorption isotherm models were used to represent the equilibrium data. The Freundlich isotherm model was fitted very well with the equilibrium data when compared to Langmuir isotherm model. The sorption results were analyzed for pseudo‐first order and pseudo‐second order kinetic model. It was observed that the kinetic data fitted very well with the pseudo‐second order rate equation when compared to the pseudo‐first order rate equation. Fourier transform infrared spectrum showed the presence of different functional groups in the biomass. The surface morphology of the sorbent was exemplified by SEM analysis. Aquatic weeds seem to be a promising biosorbent for the removal of chromium ions from water environment. This paper reports the research findings of a laboratory‐based study on the removal of Cr(VI) from the synthetic solution using the dried stem of N. rubra as a biosorbent.     

Competitive Adsorption of Nickel and Copper Ions from Aqueous Solution Using Nonliving Biomass of the Marine Brown Alga Laminaria japonica

The adsorption of nickel and copper in a bicomponent system using the nonliving biomass of the marine brown alga Laminaria japonica was investigated in batch systems as a function of initial solution pH, contact time and temperature. The adsorption of nickel and copper was strongly pH dependent. Kinetic studies pointed to a rapid uptake with an equilibrium time of about 30 min. The kinetic curves were successfully fitted by linear regression to pseudo first and pseudo‐second‐order equations. The equilibrium data was analyzed using several models, including the extended Langmuir equation, modified extended Langmuir model and combined extended Langmuir‐Freundlich model. The results suggested that the competitive adsorption of nickel and copper at all temperatures was best represented by the combined extended Langmuir‐Freundlich isotherm. The isotherms indicated competitive uptake, with copper being preferentially adsorbed followed by nickel with an increase in the amount of solute in solution. Thermodynamic analysis revealed that the simultaneous adsorption of nickel and copper ions could be considered to be a spontaneous, endothermic process, with increased randomness.     

Studies on the Removal of Iron from Drinking Water by Electrocoagulation – A Clean Process

The present study describes an electrocoagulation process for the removal of iron from drinking water using magnesium as the anode and galvanized iron as the cathode. Experiments were carried out as a function of pH, temperature and current density. The adsorption capacity was evaluated using both the Langmuir and the Freundlich isotherm models. The results show that the maximum removal efficiency of 98.4% was achieved at a current density of 0.06 A dm^–2, at a pH of 6.0. The adsorption of iron was better explained by fitting the Langmuir adsorption isotherm, which suggests a monolayer coverage of adsorbed molecules. The adsorption process followed a second‐order kinetics model. Temperature studies showed that adsorption was endothermic and spontaneous in nature.     

Adsorption of Pb(II) Ions from Aqueous Solutions by Date Bead Carbon Activated with ZnCl2

This study reports on the adsorption characteristics of Pb(II) ions from aqueous solutions using ZnCl₂‐activated date (Phoenix dactylifera) bead (ADB) carbon with respect to change in adsorbent dosage, initial pH, contact time, initial concentration, and temperature of the solution. Kinetic studies of the data showed that the adsorption follows the pseudo‐second‐order kinetic model. Thermodynamic parameters, enthalpy change (ΔH° = 55.11 kJ/mol), entropy change (ΔS° = ? 0.193 kJ/mol/K), and Gibbs free energy change (ΔG°) were also calculated for the uptake of Pb(II) ions. These parameters show that adsorption on the surface of ADB was feasible, spontaneous in nature, and endothermic between temperatures of 298.2 and 318.2 K. The equilibrium data better fitted the Langmuir and Freundlich isotherm models than the D–R adsorption isotherm model for studying the adsorption behavior of Pb(II) onto the ADB carbon. It could be observed that the maximum adsorption capacity of ADB was 76.92 mg/g at 318.2 K and pH 6.5.     

Adsorption of Thallium(I) Ions Using Eucalyptus Leaves Powder

Using batch method, the adsorption of thallium(I) ions from aqueous solutions on eucalyptus leaves powder, as a low cost adsorbent, was studied. The effect of various modification of considered adsorbent on the adsorption percentage of Tl(I) is an important feature of this study. The results showed that the unmodified and acidic modified adsorbent are the poor adsorbents for the Tl(I) ions while basic modified adsorbent is a suitable adsorbent. Also, the effect of some experimental conditions such as solution initial pH, agitation speed, contact time, sorbent dosage, temperature, particle size, and thallium initial concentration was studied. The results showed that the adsorption percentage depends on the conditions and the process is strongly pH‐dependent. The satisfactory adsorption percentage of Tl(I) ions, 81.5%, obtained at 25 ± 1°C. The equilibrium data agreed fairly better with Langmuir isotherm than Freundlich and Temkin models. The value of q_m that was obtained by extrapolation method is 80.65 mg g^?1. Separation factor values, R_L, showed that eucalyptus leaves powder is favorable for the sorption of Tl(I). The negative values of ΔH⁰ and ΔS⁰ showed that the Tl(I) sorption is an exothermic process and along with decrease of randomness at the solid–solution interface during sorption, respectively.     

Removal of Arsenic from Simulated Groundwater Using GAC‐Ca in Batch Reactor: Kinetics and Equilibrium Studies

This paper deals with kinetics and equilibrium studies on the adsorption of arsenic species from simulated groundwater containing arsenic (As(III)/As(V), 1:1), Fe, and Mn in concentrations of 0.188, 2.8, and 0.6 mg/L, respectively, by Ca²⁺ impregnated granular activated charcoal (GAC‐Ca). Effects of agitation period and initial arsenic concentration on the removal of arsenic species have also been described. Although, most of the arsenic species are adsorbed within 10 h of agitation, equilibrium reaches after ～24 h. Amongst various kinetic models investigated, the pseudo second order model is more adequate to explain the adsorption kinetics and film diffusion is found to be the rate controlling step for the adsorption of arsenic species on GAC‐Ca. Freundlich isotherm is adequate to explain the adsorption equilibrium. However, empirical polynomial isotherm gives more accurate prediction on equilibrium specific uptakes of arsenic species. Maximum specific uptake (q_max) for the adsorption of As(T) as obtained from Langmuir isotherm is 135 µg/g.     

Biosorption Kinetics and Isotherm Studies of Cd(II) by Dried Enteromorpha compressa Macroalgae Cells from Aqueous Solutions

For the first time ever, Enteromorpha compressa macroalgae (ECM), which is commonly found in Turkey, has been used as biosorbent by us. This study aims to investigate the biosorption of Cd²⁺ from aqueous solutions in a batch system by using an alga of ECM in different concentrations, pH levels, agitation rates (90–150 rpm), and contact periods. The maximum biosorption capacity of the ECM was found to be 9.50 mg/g at pH 6, Cd²⁺ initial concentration of 10 mg/L and agitation rate 150 rpm. Cadmium removal efficiency was about 95%. The experimental isotherm data were analyzed using the Langmuir and Freundlich equations. Isotherm parameters for both equations were determined and discussed. The stated biosorption mechanism is explained by the Freundlich isotherm (r² = 0.998) theory. Two simplified kinetic models including a pseudo‐first‐ and second‐order equation were selected to follow the biosorption process. Kinetic parameters; rate constants, equilibrium adsorption capacities and related correlation coefficients, for each kinetic model were calculated and discussed. It was shown that the biosorption of cadmium onto ECM could be described by the pseudo‐second‐order equation (r² > 0.99).     

The Adsorption Behavior of Functional Particles Modified by Polyvinylimidazole for Cu(II) Ion

In this paper, a novel composite material the silica grafted by poly(N‐vinyl imidazole) (PVI), i.e., PVI/SiO₂, was prepared using 3‐methacryloxypropyl trimethoxysilane (MPS) as intermedia through the “grafting from” method. The adsorption behavior of metal ions by PVI/SiO₂ was researched by both static and dynamic methods. Experimental results showed that PVI/SiO₂ possessed very strong adsorption ability for metal ions. For different metal ions, PVI/SiO₂ exhibited different adsorption abilities with the following order of adsorption capacity: Cu²⁺ > Cd²⁺ > Zn²⁺. The adsorption material PVI/SiO₂ was especially good at adsorbing Cu(II) ion and the saturated adsorption capacity could reach up to 49.2 mg/g. The empirical Freundlich isotherm was found to describe well the equilibrium adsorption data. Higher temperatures facilitated the adsorption process and thus increased the adsorption capacity. The pH and grafting amount of PVI had great influence on the adsorption amount. In addition, PVI/SiO₂ particles had excellent eluting and regenerating property using diluted hydrochloric acid solution as eluent. The adsorption ability trended to steady during 10 cycles.     

Adsorptive Removal of Acid Blue 15: Equilibrium and Kinetic Study

Activated carbons prepared from sunflower seed hull have been used as adsorbents for the removal of acid blue 15 (AB‐15) from aqueous solution. Batch adsorption techniques were performed to evaluate the influences of various experimental parameters, e. g., temperature, adsorbent dosage, pH, initial dye concentration and contact time on the adsorption process. The optimum conditions for AB‐15 removal were found to be pH = 3, adsorbent dosage = 3 g/L and equilibrium time = 4 h at 30°C. The adsorption of AB‐15 onto the adsorbent was found to increase with increasing dosage. It was found from experimental results that the Langmuir isotherm fits the data better than the Freundlich and Temkin isotherms. The maximum adsorption capacity, Q_m (at 30°C) was calculated for SF1, SF2, and SF3 as 75, 125 and 110 mg g^–1 of adsorbent, respectively. It was found that the adsorption follows pseudo‐second order kinetics. The thermodynamic parameters such as ΔG°, ΔH°, and ΔS° were also evaluated. The activated carbons prepared were characterized by FT‐IR, SEM and BET analysis.     

Equilibrium and Kinetic Studies on the Removal of Reactive Red 2 Dye from an Aqueous Solution Using a Positively Charged Functional Group of the Nymphaea rubra Biosorbent

Nymphaea rubra stem was used as a low cost and easily available biosorbent for the removal of Reactive Red 2 dye from an aqueous solution. Initially, the effects of biosorbent dosage (0.2–1.0 g L^–1), pH (1–6), and dye concentration (30–110 mg L^–1) on dye removal were studied. Batch experiments were carried out for biosorption kinetics and isotherm studies. The results showed that dye uptake capacity was found to increase with a decrease in biosorbent dosage. Equilibrium uptake capacity was found to be greatest at a pH value of 2.0, when compared to all other pH values studied. The equilibrium biosorption isotherms were analyzed by the Freundlich and Langmuir models. The equilibrium data was found to fit very well with the Freundlich isotherm model when compared to the Langmuir isotherm model. The kinetic data was analyzed using pseudo-first order and pseudo-second order kinetic models. From the results, it was observed that the kinetic data was found to fit the pseudo-second order kinetic model very well. The surface morphology of the stem of the N. rubra biosorbent was exemplified by scanning electron microscopy. Fourier transform infrared analysis was employed to confirm the existence of an amine group in the stem of N. rubra.     

Removal of Various Phenoxyalkanoic Acid Herbicides from Water by Organo‐clays

Dodecylammonium bentonite (DB) and dodecylammonium sepiolite (DS) were used as sorbents for phenoxyalkanoic acid herbicides 2,4‐D ((2,4‐dichlorophenoxy)acetic acid), 2,4‐DP ((RS)‐2‐(2,4‐dichlorophenoxy)propionic acid), 2,4‐DB (4‐(2,4‐dichlorophenoxy)butyric acid), 2,4,5‐T ((2,4,5‐trichlorophenoxy)acetic acid), and MCPA ((4‐chloro‐2‐methylphenoxy)acetic acid). Langmuir, Freundlich, and the linear Henry’s Law isotherm adsorption parameters were calculated from the adsorption isotherms. Langmuir equation showed poor fit for both adsorbents. According to the evaluation using the Freundlich equation, the DS sample showed much higher and stronger sorption capacity than DB. Similar behaviour was also observed in the case of the linear Henry’s Law isotherm. The adsorption of the herbicides on both DB and DS decreased in the order of 2,4‐DB > 2,4,5‐T > 2,4‐DP > 2,4‐D > MCPA.     

针铁矿对湖泊草、藻来源可溶有机质的非均质吸附

为探究富营养化湖泊中自生源可溶有机质(DOM)在泥水界面的吸附行为,以马来眼子菜(Potamogeton malaianus)和铜绿微囊藻(Microcystis aeruginosa)释放的DOM为代表,考察针铁矿对草、藻源DOM中不同组分的吸附特征.三维荧光平行因子分析表明类富里酸组分C1和类胡敏酸组分C4的含量很低,而类蛋白物质(类酪氨酸组分C2和类色氨酸组分C3)分别占草、藻源DOM荧光组成的70%和93%. 2种DOM均可被针铁矿吸附,吸附过程符合伪一级动力学.通过等温线拟合发现针铁矿吸附藻源DOM的非线性更强,饱和吸附量(23.77 mg/g)高于草源DOM(19.10 mg/g).特别地,类蛋白组分呈现非线性吸附,而类腐殖物质的吸附近似线性,且针铁矿对于DOM各荧光组分的吸附量顺序为:C3C2 C4 C1,此非均质吸附特征与DOM组分的初始含量、分子大小、芳香性及有效吸附位点有关.红外光谱证实氨基、羧基和羟基是吸附过程中的重要官能团.因此,草、藻源DOM显著改变了针铁矿表面的有机物质组成,影响湖泊沉积物的生物地球化学行为.     

Adsorption of Cationic Dyes from Aqueous Solution by Termite Feces,a Non‐Conventional Adsorbent

The adsorption of three cationic dyes (rhodamine B, RB; crystal violet, CV; and malachite green, MG) onto termite feces, a low‐cost adsorbent, was investigated. The adsorbent was characterized by IR spectroscopy, point of zero charge measurement, and the Boehm titration method. The adsorption follows the pseudo‐second‐order kinetic model and the Langmuir–Freundlich isotherm with maximum adsorption capacities of 95.53 mg g^?1 (RB), 75.71 mg g^?1 (CV), and 44.78 mg g^?1 (MG). The study of thermodynamics showed that the adsorption is a spontaneous and endothermic process. This works suggest that termite feces can be used as a new low‐cost adsorbent for cationic dye removal.     

Adsorption Characteristics of Reactive Black 5 from Aqueous Solution onto Chitosan

Adsorption of reactive black 5 (RB5) from aqueous solution onto chitosan was investigated in a batch system. The effects of solution pH, initial dye concentration, and temperature were studied. Adsorption data obtained from different batch experiments were modeled using both pseudo first‐ and second‐order kinetic equations. The equilibrium adsorption data were fitted to the Freundlich, Tempkin, and Langmuir isotherms over a dye concentration range of 45–100 µmol/L. The best results were achieved with the pseudo second‐order kinetic and Langmuir isotherm equilibrium models, respectively. The equilibrium adsorption capacity (q_e) was increased with increasing the initial dye concentration and solution temperature, and decreasing solution pH. The chitosan flakes for the adsorption of the dye was regenerated efficiently through the alkaline solution and was then reused for dye removal. The activation energy (E_a) of sorption kinetics was estimated to be 13.88 kJ/mol. Thermodynamic parameters such as changes in free energy (ΔG), enthalpy (ΔH), and entropy (ΔS) were evaluated by applying the van't Hoff equation. The thermodynamics of reactive dye adsorption by chitosan indicates its spontaneous and endothermic nature.     

Batch and Continuous Design of a Full‐Scale Treatment Facility for Removing Dissolved Natural Organic Matter

Batch and continuous flow adsorption experiments are carried out and the design of a full‐scale facility for removing dissolved natural organic matter (DNOM) from Catalan Lakewater is demonstrated. The adsorption efficiency is proportional to the temperature and the amount of adsorbent unlike pH increase. The highest DNOM removal rate is obtained at 35 °C, pH 4, and an adsorbent amount of 0.8 g L^?1. Optimum contact time for batch studies is 60 min at equilibrium. Correlation constants (r) of Langmuir and Freundlich isotherms are 0.8905 and 0.9739, respectively. Based on the Freundlich isotherm, the highest adsorption capacity (q_max) obtained is 2.44 and 6.01 mg DNOM/g granulated activated carbon (GAC) for raw and enriched water, respectively. Consequently, the effects of adsorbent amount, bed depth, empty bed contact time, and organic loading on removal performance are investigated in the rapid small‐scale column test (RSSCT) columns. The targeted effluent concentration of 1 mg DNOM/L can easily be achieved in the columns. At the design capacity of the facility, 15 adsorption columns with dimensions of 7 m height, 4.33 m diameter, and 22 days of operation cycle are required to remove DNOM from raw water.     

Enhancement of Carbon Dioxide Capture by Amine‐Functionalized Multi‐Walled Carbon Nanotube

In this study, crude multi‐walled carbon nanotubes (MWCNT) was functionalized by a two‐step process; first using strong mixed acids (H₂SO₄/HNO₃) and then treatment with 1,3‐phenylenediamine (mPDA). The equilibrium adsorption of CO₂ on pristine MWCNT and amine functionalized MWCNT (MWCNT‐NH₂) were investigated. Experiments were preformed via application of volumetric method in a dual sorption vessel at temperature range of 298–318 K and pressures up to 40 bars. The results obtained indicated that the equilibrium uptake of CO₂ increased after functionalizing of MWCNT. The increase in CO₂ capture by MWCNT‐NH₂ was attributed to the existence of great affinity between CO₂ molecules and amine sites on this adsorbent at low pressures. The experimental data were analyzed by means of Freundlich and Langmuir adsorption isotherm models. The data obtained revealed a fast kinetics for the adsorption of CO₂ in which most of adsorption occurred at initial period of adsorption experiments. This renders MWCNT as a suitable adsorbent for practical applications. Values of isosteric heat of adsorption were evaluated based on Clausius–Clapeyron equation. The results demonstrated that both chemisorption and physisorption played important role in CO₂ adsorption on MWCNT‐NH₂, whereas the physisorption process was dominant for CO₂ adsorption on MWCNT.     

Adsorption Kinetic and Equilibrium Studies on Removal of Lead(II) onto Glutamic Acid/Sepiolite

In this study, a modified method was used to increase the adsorption of lead ions from aqueous solutions by using modified clay mineral on the laboratory scale. Adsorption experiments have been carried out on the use of both thermal activated sepiolite (TAS) and their glutamate/sepiolite modification (GS) as adsorbents. The experimental data was analyzed using adsorption kinetic models (pseudo first‐ and second‐order equations). The pseudo second‐order kinetic model fitted well to the kinetic data (R² ≥ 0.99). Then, the Freundlich and Langmuir models were applied to describe the uptake of Pb(II) on GS and the Langmuir isotherm model agrees well with the equilibrium experimental data (R² ≥ 0.97). The maximum adsorption capacity was observed to be 128.205 mg/g by GS according to the Langmuir equation. Desorption efficiency of the GS was studied by the batch method using EDTA, HCl, and HNO₃ solutions. Desorption of 69.18, 74.55, and 80% of Pb(II) from GS was achieved with 0.1 M EDTA, 0.1 M HCl, and 0.1 M HNO₃ solutions, respectively. FTIR analysis suggests the importance of functional groups such as amino, hydroxyl, and carboxyl during Pb(II) removal. SEM observations demonstrated that an important interaction at the lead‐modified sepiolite interface occurred during the adsorption process. In addition, the thermodynamic constants was calculated that the values of the Gibbs free energy (ΔG*), enthalpy (ΔH*), and entropy (ΔS*) of modification were 86.79 kJ/mol, ?18.91 kJ/mol, and ?354.70 J/mol/K, respectively. The negative value of ΔH* shows exothermic nature of adsorption.