Parametric analysis of eccentric structure–soil interaction system based on branch mode decoupling method

In order to carry out parametric analysis of eccentric structure–soil interaction system, an analytical model based on branch mode decoupling method is presented in this paper. The solution of system equations is implemented in the frequency domain by assuming that the superstructure maintains classic normal modes. The transfer functions of translational and torsional response are derived later. The influence of eccentricity ratio, torsional to translational frequency ratio, height-to-base ratio and foundation flexibility on the curve and peak value of transfer functions and torsionally coupled degree are analyzed and discussed systematically. Results of analysis indicate that the flexibility of foundation soil can weaken the torsional response of superstructure substantially, and the natural frequencies of interaction system reduce as the flexibility of foundation soil increase. The influence of eccentricity ratio on the peak values of transfer functions varies with the torsional to translational frequency ratio, which can be summarized as the decrease of translational component and the increase of torsional component. The translational displacement of SSI system is larger than that of fixed-base condition, while the deformation amplitude is notably reduced. The torsional response decreases as well. As the height-to-base ratio increase, the varying tendency of response is further enhanced. The torsionally coupled degree of eccentric structure is remarkably affected by the torsional to translational frequency ratio, which is significantly reduced under soft soil condition.     

Shake table tests on a mass eccentric model with base isolation

A mass eccentric structure is usually more seismically vulnerable than its concentric counterpart because of the coupled torsional–translational response of such structures. In this work, dynamic characteristics and response of a five‐storey benchmark model with moderate mass eccentricity were investigated using a shake table, simulating four different ground motions. The effectiveness of laminated rubber bearings (LRB) and lead‐core rubber bearings (LCRB) in protecting eccentric structures was examined and evaluated in relation to translational and torsional responses of the benchmark model. It was observed that both translational and torsional responses were significantly reduced with the addition of either a LRB or LCRB isolated system regardless of the nature of ground motion input. The LRB were identified to be more effective than LCRB in reducing model relative displacements, the relative torsional angle as well as accelerations, and therefore provided a better protection of the superstructure and its contents. On the other hand, LCRB rendered a smaller torsional angle and absolute displacement of the base isolation system, hence a more stable structural system. Copyright © 2003 John Wiley & Sons, Ltd.     

Effective eccentricity for inelastic seismic response of buildings

The concept of effective eccentricity is generalized for inelastic systems to provide guidelines for estimating the maximum dynamic edge displacement and resisting element deformation of a single mass monosymmetrical system subjected to unidirectional ground excitations. Inelastic responses of three structural models having the same overall elastic responses are compared and the model which generally results in larger edge displacement is chosen as the structural model to be used to evaluate the effect of asymmetry. The inelastic effective eccentricity is calculated for different values of the system parameters, based on an ensemble of six ground motion records as input. It is concluded that, except for stiff structures having low yield strength, the elastic effective eccentricity curves developed previously by Dempsey and Tso can provide a reasonable or relatively conservative estimate for inelastic effective eccentricity, and these curves can be used to estimate the edge displacement and element deformation of inelastic eccentric systems.     

Dynamic response of bilinear asymmetric structures

The inelastic behaviour of eccentric single-storey building structures subjected to sinusoidal ground excitation is examined. The Kryloff-Bogoliuboff method is employed to provide approximate solutions in the amplitude-frequency domain. Structural resisting elements are assumed to exhibit bilinear hysteretic behaviour and coupled response is investigated in terms of both system response as well as individual element ductility requirements. In addition to demonstrating the well-known softening property inherent in yielding systems, the importance of the principal parameters governing coupled response is evaluated in a consistent parametric fashion. Within the context of earthquake resistant building design, the results indicate the absence of amplified response when torsional and translational frequencies are close, in contrast to the much emphasized observation of internal resonance for linear elastic structures. Equally important, structural elements located on the stiff edge of eccentric buildings are found to be only marginally affected by the magnitude of the eccentricity, thus indicating that seismic building codes which reduce design requirements for these elements underestimate actual behaviour substantially.     

Effect of stiffness variability on the response of isolated structures

Results are presented of an investigation, the objective of which was to determine the relationship between the stiffness variability of the bearings of an isolation system and the response variability of the structure. The system is modeled as a rigid, rectangular structure that is free to translate and rotate. The isolation system consists of N isolation bearings arranged in a rectangular pattern, each with a stiffness k_i that is an independent, normally distributed, random variable. Response spectrum analysis is used to obtain the analytical solution for the structure response. Approximate closed‐form expressions are obtained for the variance of the centreline displacement, rotation, corner displacement and base shear, that are in terms of the variability of the isolator stiffness, aspect ratio of the structure, and the number and layout of isolation bearings. Results show that the standard deviation of the centreline displacement and base shear decrease with increasing number of isolation bearings, and are independent of the aspect ratio and layout of isolators, and in all cases are less than 1/4 the standard deviation of the isolator stiffness. The standard deviation of the corner displacement is a function of all of the system parameters, and is bounded below by the standard deviation of the centreline displacement and above by the standard deviation of a bar aligned perpendicular to the direction of ground motion with m isolation bearings distributed along the length. The approximate expressions are shown to be in good agreement with the results of Monte Carlo simulations. The results should be of use to designers of isolated structures and manufacturers of isolation systems, in assessing the significance of stiffness variability on the response of the isolated structure. Copyright © 2000 John Wiley & Sons, Ltd.     

SMA阻尼器偏心结构平-扭震动控制试验研究

为了验证提出的新型筒式自复位形状记忆合金阻尼器(telescopic recentering shape memory al-loy damper,TRSMAD)对结构平动-扭转耦联振动反应的抑制作用,进行了偏心结构消能减震体系的振动台试验。设计了一个1/4缩尺的三层两跨单向偏心的钢框架模型,将提出的新型SMA阻尼器安装在结构底层的一侧,通过振动台分别对无控条件下和装有阻尼器的有控条件下的结构反应进行了研究。试验结果表明:(1)在各地震波作用下,TRSMAD对结构的平动反应有很好控制效果,而对结构各层扭转角位移的控制效果稍低;(2)不同地震波下的控制效果有所不同:对结构的平动位移而言,天津波的减震率最高,El Centro波次之,最后为Taft波;对结构扭转角的控制,平均而言,除了天津波作用下第二层为特例外,对El Centro波的减震效果最好,其次为Taft波,最后为天津波;(3)同一地震波下,阻尼器对结构模型一层的位移控制效果较其他层为优。     

Sloshing response of layered liquids in rigid tanks

The sloshing action of layered liquids in rigid cylindrical and long rectangular tanks is investigated, considering both their free vibrational characteristics and their response to a horizontal component of base shaking. Special attention is given to the maximum surface displacement induced by the base motion. The analysis is formulated for systems with N superimposed layers of different thicknesses and densities, and is illustrated by a numerical example. In addition, comprehensive numerical data are presented for two-layered and some three-layered systems which elucidate the underlying response mechanisms and the effects and relative importance of the numerous parameters involved. It is shown that for each horizontal natural mode of vibration, there are N distinct vertical modes, the frequencies of which are lower than the natural frequency of a homogeneous liquid of the same total depth. It is further shown that the maximum surface sloshing displacement of the base-excited layered system is typically larger than that of the corresponding homogeneous system, and that the results for the long rectangular and cylindrical tanks are quite similar.     

双向地震动作用的拟等延性系数谱

首先建立了以强度折减系数表述的恢复力特性满足二维屈服面模型的理想弹塑性单质点系统(它在2个相互垂直的主轴方向上分别具有水平平动自由度)在双向地震动作用下的归一化运动方程。然后引入单向地震动作用下等延性系数的强度折减系数谱,给出了双向地震动作用的拟等延性系数谱(定义为系统分别承受双向和单向地震动作用,在同一主轴方向上的最大位移反应之比)最后通过硬土场地10组双向地震动记录拟等延性系数谱的统计平均结果,分析了结构周期、位移延性系数和阻尼等因素对谱值及结构双向地震反应的影响。结果表明,双向地震动作用与单向地震动作用相比主要增加结构较长周期方向的最大位移反应。若在基于位移的抗震设计中降低结构较短周期方向的设计位移延性系数,可在一定程度上降低双向地震动的不利影响。因定义的谱为比值形式,阻尼对其影响不大。     

Inelastic seismic response of simple eccentric structures

The maximum ductility demand and the edge displacement of a simple single mass eccentric model is evaluated when the system is subjected to ground motions represented by the El Centro 1940 and Taft 1952 earthquake records. The resisting elements are taken to be bilinear hysteretic. It is found that the ductility demand depends to a great extent on the energy content of the ground motions, particularly in the period range beyond the elastic period of the system. Unlike elastic response, the coincidence of uncoupled torsional and lateral frequencies does not lead to exceptionally high inelastic response. An increase by a factor of two in ductility demand is not uncommon for a system with large eccentricity as compared to a symmetrical system. Therefore, system eccentricity has a larger effect on ductility demand than earlier studies indicated. Using Clough's model to allow for stiffness degradation effect, results are found to be within 20 per cent of those calculated based on the bilinear hysteretic model.     

Maximum seismic displacement of inelastic systems based on energy concept

The energy balance and energy input of Single-Degree-of-Freedom (SDF) systems under earthquake motion is studied for elastic and inelastic systems. The maximum displacement of an inelastic system is related to that of an elastic system having the same initial stiffness and mass by considering the earthquake energy input per cycle of oscillation. With an assumption that the cyclic energy input is equal for both elastic and inelastic system for intermediate- and long-period systems, a simplified relation is suggested. Newmark's equal energy rule is shown to be the upper bound of the simplified relation; the lower bound of maximum response displacement is also derived in this paper. The numerical analysis results were mostly shown to fall between the proposed upper and lower bounds. A separate approximate relation is proposed for short-period systems. The reason for divergence from the suggested relations is discussed for short-period systems. Copyright © 1999 John Wiley & Sons Ltd.     

Seismic response of base-isolated structures with vertical-rocking coupling

A base-isolated building is liable to have a small horizontal eccentricity between the centre of mass of the superstructure and the centre of rigidity of the supporting bearings. In seismic analysis, the structure is modelled as a rigid block with tributary masses supported on massless elastomeric rubber bearings placed at a constant elevation below the centre of mass. This simplified system has three degrees of freedom: two translations and one rotation in the vertical plane. The investigation of the dynamic behaviour of a base-isolated building is carried out for both the detuned and the perfectly tuned cases. In the detuned case, the natural frequencies of the system are assumed to be well separated. In the perfectly tuned case, the uncoupled rocking frequency is assumed to be identical to the vertical translational frequency, which may result from an unusual mass distribution and/or an extreme aspect ratio of the superstructure. Perturbation methods are implemented in finding the dynamic characteristics for both cases. However, the dynamic response of the perfectly tuned case is the major concern in this investigation. The Green's functions for the displacement response of the three-degree-of-freedom system are derived for both the undamped and damped conditions. The response spectrum modal superposition method is used in estimating the maximum acceleration response. A simple method, accounting for the effect of closely spaced modes, is proposed for combining modal maxima and results in an approximate solution corresponding to a single-degree-of-freedom system. This approximate solution may be used for the preliminary design of a base-isolated structure. Numerical results for a base-isolated building subjected to the vertical component of the El Centro earthquake of 1940 were carried out for comparison with these analytical results. The proposed modal combination method showed superiority over the conventional Square Root of the Sum of the Squares method in estimating maximum responses. The results also indicated that the approximate single-degree-of-freedom system yields accurate estimations. It is shown that the effect of rocking coupling on the vertical response of base-isolated structures subjected to transient loadings, such as earthquake motions, can generally be neglected as a result of the combined effects of the time lag between the maximum translational and rotational responses and the influence of damping in the isolation system, which for elastomeric bearings can be as high as 8 to 10 per cent of critical.     

Effective strength eccentricity concept for inelastic analysis of asymmetric structures

A large number of parameters affect the inelastic response of an eccentric system. The centre of resistance no longer remains constant due to continuous loading and unloading of various elements of the system in and out of the inelastic region. The objective of this study is to develop the concept of strength eccentricity for asymmetrical structures excited well into the inelastic region in the event of a severe earthquake. A single mass monosymmetric three-element system is selected. The torsional flexibility parameter is varied so as to obtain nine eccentric configurations covering the entire spectrum of such systems. These models were subjected to S00E component of the El Centro earthquake of 1940 which is considered to be a very severe earthquake. The concept of effective strength eccentricity is introduced which is defined as strength eccentricity at the point of intersection of ductility ratio curves of REE and FEE. It is proposed to provide additional strength in the elements of a torsionally unbalanced system independent of the design eccentricity. Empirical equations are proposed to account for design eccentricity and additional strength as well as distribution of the design strength. The proposed formulation is compared with the torsional provisions of UBC 1991, NBCC 1990 and NZC 1992. It is concluded that additional ductility demand on the REE and FEE designed based on the proposed formulation is almost nil as compared to that given by the three codes. The NZC and UBC require maximum ductility on the REE. The increase in overall strength of the system is least for the proposed formulation as compared to that given by the three codes. NBCC consistently requires the maximum total strength ratio.     

Seismic response of torsionally coupled base isolated structures

An analytical study of the seismic response of typical base isolated structures mounted on rubber bearings is presented. Isolated buildings are liable to have closely spaced lower modes of vibration with small eccentricity between centres of mass and rigidity. The isolated structure is modelled as a rigid deck with lumped masses supported on axially inextensible elastomeric rubber bearings. This simplified system has three degrees of freedom (dof), two translations and one rotation in the horizontal plane. The Green's functions for the displacement response of the 3 dof system are derived for both undamped and damped cases with small and large eccentricities. The small eccentricity case is taken from a specific isolated building, while the large eccentricity case arises from the 5 per cent accidental eccentricity which is required by various seismic codes. An interaction equation for normalized displacements is established for an idealized flat velocity spectrum or hyperbolic acceleration spectrum. An isolated building on rubber bearings would have its fundamental period fall into this range of a design spectrum. Numerical results for the specific building subjected to the El Centro earthquake of 1940 are presented. Both the time history and the response spectrum modal superposition analysis were performed. In the response spectrum analysis, the Complete Quadratic Combination (CQC) showed superiority over the Square Root of the Sum of Squares (SRSS) in estimating maximum responses. It is concluded that the effect of torsional coupling on the transient response of base isolated structures is insignificant, due to the combined effect of the time lag between the maximum translational and torsional responses and the influence of damping in the isolation system which for elastomeric bearings can be as high as 8 to 10 per cent.     

地震动群延时不确定性对反应谱的影响研究

为了考察外部激励群延时对反应谱的影响,分别从确定性的角度和统计的角度分析了群延时对线性单自由度结构体系位移响应最大值的影响。推导出了对应于给定单自由度结构体系在任意外部激励作用下最大位移响应的群延时。据此可以利用任意外部激励的群延时与结构体系的最大位移响应群延时的关系评估体系在该外部激励作用下位移响应峰值的大小。统计分析的结果表明:激励群延时的均值和方差对结构体系位移响应最大值的影响具有明显的规律性;激励群延时的分布频数与结构体系最大位移响应之间也存在着显著的关系。     

四种地下结构抗震设计简化分析方法对比

在地下结构抗震设计简化分析方法中,强制反应位移法将土层变形施加在有限元模型侧边界模拟地震作用,反应加速度法将土层加速度施加到整个有限元模型上模拟地震作用,此外还有仅将土层加速度施加到土层模型上模拟地震作用的方法。上述方法均规避了反应位移法中关于弹簧刚度的取值问题,提高了计算效率。本文以1个双跨箱形结构为例,用动力时程分析的计算结果作为校核,分析了强制反应位移法、反应加速度法和仅将土层加速度施加到土体中的简化分析方法在不同侧边距条件下的计算精度,再结合常用的反应位移法,对比分析了4种简化分析方法的误差。分析结果表明:使用强制反应位移法时,侧边距取为1倍结构宽度导致的误差最小,反应加速度法和仅在土体施加加速度的简化方法对侧边距取值不敏感,反应位移法在角点造成的误差最大。     

A probabilistic framework for estimating the residual drift of idealized SDOF systems of non‐degrading conventional and damped structures

This paper presents a general framework for predicting the residual drift of idealized SDOF systems that can be used to represent non‐degrading structures, including those with supplemental dampers. The framework first uses post‐peak oscillation analysis to predict the maximum ratio of residual displacement to the peak transient displacement in a random sample. Then, residual displacement ratios obtained from nonlinear time‐history analyses using both farfield and near‐fault‐pulse records were examined to identify trends, which were explained using the oscillation mechanics of SDOF systems. It is shown that large errors can result in existing probability models that do not capture the influence of key parameters on the residual displacement. Building on the observations that were made, a general probability distribution for the ratio of residual displacement to the peak transient displacement that more accurately reflects the physical bounds obtained from post‐peak oscillation analysis is proposed for capturing the probabilistic residual displacement response of these systems. The proposed distribution is shown to be more accurate when compared with previously proposed distributions in the literature due to its explicit account of dynamic and damping properties, which have a significant impact on the residual displacement. This study provides a rational basis for further development of a residual drift prediction tool for the performance‐based design and analysis of more complex multi‐degree‐of‐freedom systems.     

旋转地震合成及其在大跨度悬索桥中的应用

为探究旋转地震动在大跨度悬索桥中的应用,首先,从线弹性理论和功率谱角度基于随机振动理论提出了6维地震动加速度功率谱模型;其次,基于MATLAB编制旋转地震动人工地震合成程序,从反应谱角度对合成地震动进行了正确性验证和拟合精度迭代调整;最后,分析了旋转地震动与地震动入射角对桥梁结构地震响应的影响。研究表明：人工合成的地震动平动分量反应谱与实测地震动的平动分量反应谱吻合度较高;六维地震动的主梁跨中竖向位移越是三维平动地震动的3倍,而主缆轴力峰值接近2.25E+05kN,约是三维平动地震动的1.3倍;旋转地震动和地震动入射角将会加大桥梁结构的位移响应和内力响应,且会减小塔底截面和桩最不利截面的安全性。     

Kinematic soil-structure interaction effects on maximum inelastic displacement demands of SDOF systems

This paper presents a statistical study of the kinematic soil-foundation-structure interaction effects on the maximum inelastic deformation demands of structures. Discussed here is the inelastic displacement ratio defined as the maximum inelastic displacement demands of structures subjected to foundation input motions divide by those of structures subjected to free-field ground motions. The displacement ratio is computed for a wide period range of elasto-plastic single-degree-of-freedom (SDOF) systems with various levels of lateral strength ratios and with different sizes of foundations. Seventy-two earthquake ground motions recorded on firm soil with average shear wave velocities between 180 m/s and 360 m/s are adopted. The effects of period of vibration, level of lateral yielding strength and dimension of foundations are investigated. The results show that kinematic interaction will reduce the maximum inelastic displacement demands of structures, especially for systems with short periods of vibration, and the larger the foundation size the smaller the maximum inelastic displacement becomes. In addition, the inelastic displacement ratio is nearly not affected by the strength ratio of structures for systems with periods of vibration greater than about 0.3 s and with strength ratios smaller than about 3.0. Expressions obtained from nonlinear regression analyses are also proposed for estimating the effects of kinematic soil-foundation-structure interaction from the maximum deformation demand of the inelastic system subjected to free-field ground motions.     

UNCOUPLED FREQUENCY RATIO IN ASYMMETRIC BUILDINGS

Structural eccentricity and Uncoupled Frequency Ratio (UFR) are two system parameters that strongly influence the elastic response of eccentric structures. The opinions differ regarding their influence on the inelastic response. Different investigators arrived at contradictory conclusions on the influence of uncoupled frequency ratio. The reasons for these contradictions are the use of different definitions and different models in the inelastic studies. In this paper, three possible definitions of the uncoupled frequency ratio are identified, and their influence is studied on the inelastic response. An ensemble of 10 real earthquakes of 20 s duration is used. The response is measured in terms of the mean plus one standard deviation of the ductility ratio. The value of the UFR obtained by each of the three possible definitions is not always admissible. It is concluded that the inelastic response depends upon the eccentric system, definition employed for the UFR, time period of the eccentric systems and the basis of strength distribution among the various lateral elements.     

Complex complete quadratic combination method for damped system with repeated eigenvalues

A new response-spectrum mode superposition method, entirely in real value form, is developed to analyze the maximum structural response under earthquake ground motion for generally damped linear systems with repeated eigenvalues and defective eigenvectors. This algorithm has clear physical concepts and is similar to the complex complete quadratic combination (CCQC) method previously established. Since it can consider the effect of repeated eigenvalues, it is called the CCQC-R method, in which the correlation coefficients of high-order modal responses are enclosed in addition to the correlation coefficients in the normal CCQC method. As a result, the formulas for calculating the correlation coefficients of high-order modal responses are deduced in this study, including displacement, velocity and velocity-displacement correlation coefficients. Furthermore, the relationship between high-order displacement and velocity covariance is derived to make the CCQC-R algorithm only relevant to the high-order displacement response spectrum. Finally, a practical step-by-step integration procedure for calculating high-order displacement response spectrum is obtained by changing the earthquake ground motion input, which is evaluated by comparing it to the theory solution under the sine-wave input. The method derived here is suitable for generally linear systems with classical or non-classical damping.