Gully erosion in Mangatu Forest,New Zealand,estimated from digital elevation models

The methodology and errors involved in determining the amount of sediment produced during two (19·5 and 33·2 year) periods by 11 (c. 0·01 − >0·20 km²) gullies within a 4 km² area in the headwaters of the Waipaoa River basin, New Zealand, using sequential digital elevation models are described. Sediment production from all gullies within the study area was 0·99 ± 0·03 × 10⁶ t a⁻¹ (2480 ± 80 t ha⁻¹ a⁻¹) during the period from 1939 to 1958. It declined to 0·62 ± 0·02 × 10⁶ t a⁻¹ (1550 ± 50 t ha⁻¹ a⁻¹) during the period from 1958 to 1992, when many of the smaller gullies were stabilized by a programme of afforestation, which commenced in 1960. Both figures are very high by global standards. The two largest (the Tarndale and Mangatu) gully complexes together generated 73 and 95 per cent of the sediment in the specified time periods, but the latter amount is equivalent to only c. 5 per cent of the total annual sediment load of the Waipaoa River. © 1998 John Wiley & Sons, Ltd.     

Sediment production and yield from an alluvial gully in northern Queensland,Australia

Sediment production, transport and yield were quantified over various timescales in response to rainfall and runoff within an alluvial gully (7 · 8 ha), which erodes into dispersible sodic soils of a small floodplain catchment (33 ha) along the Mitchell River, northern Australia. Historical air photographs and recent global positioning system (GPS) surveys and LiDAR data documented linear increases in gully area and volume, indicating that sediment supply has been relatively consistent over the historic period. Daily time lapse photography of scarp retreat rates and internal erosion processes also demonstrated that erosion from rainfall and runoff consistently supplied fine washload (< 63 µm) sediment in addition to coarse lags of sand bed material. Empirical measurements of suspended sediment concentrations (10 000 to >100 000 mg/L) and sediment yields (89 to 363 t/ha/yr) were high for both Australian and world data. Total sediment yield estimated from empirical washload and theoretical bed material load was dominated by fine washload (< 63 µm). A lack of hysteresis in suspended sediment rating curves, scarp retreat and sediment yield correlated to rainfall input, and an equilibrium channel outlet slope supported the hypothesis that partially or fully transport‐limited conditions predominated along the alluvial gully outlet channel. This is in contrast to sediment supply‐limited conditions on uneroded floodplains above gully head scarps. While empirical data presented here can support future modelling efforts to predict suspended sediment concentration and yield under the transport limiting situations, additional field data will also be needed to better quantify sediment erosion and transport rates and processes in alluvial gullies at a variety of spatial and temporal scales. Copyright © 2013 John Wiley & Sons, Ltd.     

Turbidity and suspended sediment dynamics in small catchments in the Nepal Middle Hills

The Himalayan environment has, until recently, been perceived to be in a critical state of environmental decline, resulting from rapid population growth and associated land‐use change. Recent research, however, has emphasized the difficulty of developing an objective appraisal of the state of the environment in a region where empirical data are scarce and unstructured and where an understanding of the spatial and temporal dynamics of natural environmental processes remains highly uncertain. This paper presents results from an intensive three‐year project designed to help address the regional empirical deficit, establish detailed baseline environmental data and to gain an insight into storm period and seasonal suspended sediment dynamics. The instrumentation, calibration and analysis of high‐frequency infrared turbidimetric records from a number of small subcatchments in the Nepal Middle Hills are reported. Storm period and seasonal variation in turbidity and suspended sediment are examined and hysteresis patterns explored and explained. A variety of methods to estimate seasonal suspended sediment yield in a mixed land‐use catchment are examined, and found to vary by up to a factor of five. Despite the inherent uncertainty, all estimates of catchment sediment yield are found to be high with respect to erosion plot studies from the local area, and this suggests the importance of riparian and channel erosion as major sediment sources, a finding consistent with other regional studies. Copyright © 2000 John Wiley & Sons, Ltd.     

Sediment production in large gullies of the Mediterranean area (NE Spain) from high‐resolution digital elevation models and geographical information systems analysis

Recent studies in the Mediterranean area have shown gully erosion to have a very significant contribution to total soil loss. In the Penedès vineyard region (NE Spain), between 15 and 27% of the land is affected by large gullies and gully‐wall retreat seems to be an ongoing process. Multi‐date digital elevation model (DEM) analysis has allowed computation of sediment production by gully erosion, showing that the sediment production rates are very high by the, up‐to‐date, usual global standards. Here, we present a study carried out using large‐scale multi‐date (1975 and 1995) aerial photographs (1 : 5000 and 1 : 7000) to monitor sediment yield caused by large gullies in the Penedès region (NE Spain). High‐resolution DEMs (1 m grid) were derived and analysed by means of geographical information systems techniques to determine the gully erosion rates. Rainfall characteristics within the same study period were also analysed in order to correlate with the soil loss produced. Mass movement was the main process contributing to total sediment production. This process could have been favoured by rainfalls recorded during the period: 58% of the events were of an erosive character and showed high kinetic energy and erosivity. A sediment production rate of 846 ± 40 Mg ha^?1 year^?1, a sediment deposition rate of 270 ± 18 Mg ha^?1 year^?1 and a sediment delivery ratio of 68·1% were computed for a gully area of 0·10 km². The average net erosion within the study period (1975–95) was 576 ± 58 Mg ha^?1 year^?1. In comparison with other methods, the proposed method also includes sediment produced by processes other than only overland flow, i.e. downcutting, headcutting, and mass movements and bank erosion. Copyright © 2003 John Wiley & Sons, Ltd.     

Gully catchments as a sediment sink,not just a source: Results from a long‐term (~12 500 year) sediment budget

Sediment delivery from hillslopes to trunk streams represents a significant pathway of mass transfer in the landscape, with a large fraction facilitated by gully systems. The internal gully geomorphic dynamics represent a considerable gap in many landscape and empirical erosion models, therefore a better understanding of these processes over longer timescales (10–10⁴ years) is needed. This study analyses the sediment mass balance and storage dynamics within a headwater gully catchment in central Europe over the last ~12 500 years. Human induced erosion resulted in hillslope erosion rates ~2.3 times higher than under naturally de‐vegetated conditions (during the Younger Dryas), however the total sediment inputs to the gully system (and therefore gully aggradation), were similar. Net gully storage has consistently increased to become the second largest term in the sediment budget after hillslope erosion (storage is ~45% and ~73% of inputs during two separate erosion and aggradation cycles). In terms of the depletion of gully sediment storage, the sediment mass balance shows that export beyond the gully fan was not significant until the last ~500 years, due to reduced gully fan accommodation space. The significance of storage effects on the gully sediment mass balance, particularly the export terms, means that it would be difficult to determine the influences of human impact and/or climatic changes from floodplain or lake sedimentary archives alone and that the sediment budgets of the headwater catchments from which they drain are more likely to provide these mechanistic links. Copyright © 2015 John Wiley & Sons, Ltd.     

Use of fallout tracers 7Be, 210Pb and 137Cs to distinguish the form of sub‐surface soil erosion delivering sediment to rivers in large catchments

Fallout radionuclides (FRNs) ¹³⁷Cs and ²¹⁰Pb are well established as tracers of surface and sub‐surface soil erosion contributing sediment to river systems. However, without additional information, it has not been possible to distinguish sub‐surface soil erosion sources. Here, we use the FRN ⁷Be (half‐life 53 days) in combination with ¹³⁷Cs and excess ²¹⁰Pb to trace the form of erosion contributing sediment in three large river catchments in eastern Australia; the Logan River (area 3700 km²), Bowen River (9400 km²) and Mitchell River (4700 km²). We show that the combination of ¹³⁷Cs, excess ²¹⁰Pb and ⁷Be can discriminate horizontally aligned sub‐surface erosion sources (rilled and scalded hillslopes and the floors of incised drainage lines and gully ‘badland’ areas) from vertical erosion sources (channel banks and gully walls). Specifically, sub‐surface sources of sediment eroded during high rainfall and high river flow events have been distinguished by the ability of rainfall‐derived ⁷Be to label horizontal soil surfaces, but not vertical. Our results indicate that in the two northern catchments, erosion of horizontal sub‐surface soil sources contributed almost as much fine river sediment as vertical channel banks, and several times the contribution of hillslope topsoils. This result improves on source discrimination provided previously and indicates that in some areas erosion of hillslope soils may contribute significantly to sediment yield, but not as topsoil loss. We find that in north‐eastern Australia, scalded areas on hillslopes and incising drainage lines may be sediment sources of comparable importance to vertical channel banks. Previous studies have used the combination of ¹³⁷Cs, excess ²¹⁰Pb and ⁷Be to estimate soils losses at the hillslope scale. Here, we show that with timely and judicious sampling of soil and sediment during and immediately after high flow events ⁷Be measurements can augment fallout ¹³⁷Cs and ²¹⁰Pb to provide important erosion source information over large catchments. Copyright © 2013 John Wiley & Sons, Ltd.     

Gully‐head erosion processes on a semi‐arid valley floor in Kenya: a case study into temporal variation and sediment budgeting

A three year monitoring programme of gully‐head retreat was established to assess the significance of sediment production in a drainage network that expanded rapidly by gully‐head erosion on the low‐angled alluvio‐lacustrine Njemps Flats in semi‐arid Baringo District, Kenya. This paper discusses the factors controlling the large observed spatial and temporal variation in gully‐head retreat rates, ranging from 0 to 15 m a^?1. The selected gullies differed in planform and in runoff‐contributing catchment area but soil material and land use were similar. The data were analysed at event and annual timescales. The results show that at annual timescale rainfall amount appears to be a good indicator of gully‐head retreat, while at storm‐event timescale rainfall distribution has to be taken into account. A model is proposed, including only rainfall (P) and the number of dry days (DD) between storms: which explains 56 per cent of the variation in retreat rate of the single‐headed gully of Lam1. A detailed sediment budget has been established for Lam1 and its runoff‐contributing area (RCA). By measuring sediment input from the RCA, the sediment output by channelized flow and linear retreat of the gully head for nine storms, it can be seen that erosion shifts between different components of the budget depending on the duration of the dry period (DD) between storms. Sediment input from the RCA was usually the largest component for the smaller storms. The erosion of the gully head occurred as a direct effect of runoff falling over the edge (GH_waterfall) and of the indirect destabilization of the adjacent walls by the waterfall erosion and by saturation (GH_mass/storage). The latter component (GH_mass/storage) was usually much larger that the former (GH_waterfall). The sediment output from the gully was strongly related to the runoff volume while the linear retreat, because of its complex behaviour, was not. Overall, the results show that the annual retreat is the optimal timescale to predict retreat patterns. More detailed knowledge about relevant processes and interactions is necessary if gully‐head erosion is to be included in event‐based soil erosion models. Copyright © 2001 John Wiley & Sons, Ltd.     

Distributed evaluation of the contribution of soil erosion to the sediment yield from a watershed

The correct determination of the sediment yield from a basin is of paramount importance in several hydraulic and environmental applications, such as the evaluation of the storage reduction of artificial reservoirs. However, due to the highly episodic nature of sediment supply and transport in many environments and to the extreme complexity of the processes involved, the evaluation of the sediment load in a river is still highly uncertain. When the time scale of interest is sufficiently long, and when the primary sediment source comes from distributed erosion in the watershed, the problem can be tackled in an indirect fashion, by computing the contribution to the annual suspended yield from soil erosion. In order to accomplish this task, we propose a distributed application of the widely used USLE formula. The formula is automatically applied along drainage networks derived from a digital elevation model and properly modified to take into account the presence of deposition zones in the watershed. © 1997 John Wiley & Sons, Ltd.     

Raindrop‐induced saltation and the enrichment of sediment discharged from sheet and interrill erosion areas

Sheet and interrill erosion areas are sources of soil material rich in nutrients and pollutants. The loss of soil, nutrients and other chemicals from these areas is a matter of concern both in terms of maintaining soil productivity and the health of offsite environments. Many experiments on rainfall erosion have shown enrichment of fine material, nutrients and other chemicals in the sediment discharged for sheet and interrill erosion areas, but often these results were obtained over short periods of time. A qualitative mechanistic model of raindrop‐induced saltation is used to illustrate how this transport mechanism influences the composition of sediment discharged by rain‐impacted flow. Initially, fast moving particles are enriched in the sediment discharge but, over time, during a rainfall event, slower moving particles become more represented. Raindrop‐induced saltation promotes the storage of material on the soil surface with a coarser composition than the original soil. Winnowing of material from this storage by the development of flow‐driven saltation during high‐intensity events can modify the composition of the sediment discharged later by raindrop‐induced saltation. Given stable soil particles, the composition of the sediment discharged at the steady state is the same as the original soil. Enrichment is a non‐steady‐state phenomenon and failure to recognize the transient nature of enrichment may lead to inappropriate interpretation of the implications of the results from short‐term experiments. Copyright © 2011 John Wiley & Sons, Ltd.     

Similarity between morphological characteristics of rills and ephemeral gullies in Sicily,Italy

This paper reports the results of a field investigation aimed to establish morphological similarity between rills and ephemeral gullies. Rill measurements were made on 14 plots having a surface area of 22–352 m² located on a 14·9% slope and on a plot 6·0 m wide and 22·0 m long having a uniform 22·0% slope. The plots are located on the experimental station for soil erosion measurements, ‘Sparacia’, of the Agricultural Faculty of Palermo University, in Sicily, Italy. All plots are subjected to natural rainfall. The measurements were made immediately following five events between November 2004 and December 2005. The ephemeral gully measurements were made on a cultivated area of about 120 ha, located in Central Sicily, which is representative of many soil‐crop conditions in the Mediterranean basin. The morphological similarity between rill and ephemeral gully was first tested. Then a power relationship between rill or gully volume and length, theoretically deduced by dimensional analysis and self‐similarity theory, was applied. This power relationship needs a different scale factor for rill and gully measurements. Finally, using two dimensionless groups representative of the channel morphology variables, the analysis showed that a single relationship can be applied to rill and gully measurements. Copyright © 2009 John Wiley & Sons, Ltd.     

Impacts of headcut height on flow energy,sediment yield and surface landform during bank gully erosion processes in the Yuanmou Dry‐hot Valley region,southwest China

To quantify the changes in flow energy, sediment yield and surface landform impacted by headcut height during bank gully erosion, five experimental platforms were constructed with different headcut heights ranging from 25 to 125 cm within an in situ active bank gully head. A series of scouring experiments were conducted under concentrated flow and the changes in flow energy, sediment yield and surface landform were observed. The results showed that great energy consumption occurred at gully head compared to the upstream area and gully bed. The flow energy consumption at gully heads and their contribution rates increased significantly with headcut height. Gully headcuts also contributed more sediment yield than the upstream area. The mean sediment concentrations at the outlet of plots were 2.3 to 7.3 times greater than those at the end of upstream area. Soil loss volume at gully heads and their contribution rates also increased with headcut height significantly. Furthermore, as headcut height increased, the retreat distance of gully heads increased, which was 1.7 to 8.9 times and 1.1 to 3.2 times greater than the incision depth of upstream area and gully beds. Positive correlations were found between energy consumption and soil loss, indicating that energy consumption could be used to estimate soil loss of headcut erosion. Headcut height had a significant impact on flow energy consumption, and thus influenced the changes in sediment yield and landform during the process of gully headcut erosion. Headcut height was one of the important factors for gully erosion control in this region. Further studies are needed to identify the role of headcut height under a wide condition. Copyright © 2018 John Wiley & Sons, Ltd.     

Magnitude and variation in the contribution of bank erosion to the suspended sediment load of the River Severn,UK

The wide range of studies describing the role of bank erosion in fluvial sediment supply have mostly lumped amounts of bank erosion into coarse temporal units, such as years. This paper investigates sediment yields from individual bank erosion events within the upper River Severn, UK (basin area 380 km²). Manual erosion pins and photo-electronic erosion pins were used to estimate bank erosion, and turbidity meters were used to determine suspended sediment transport. At the annual time-scale, the silt-clay fraction of bank-derived sediment accounted for an equivalent of 17 per cent of the suspended load, increasing to an average of 38 per cent at the monthly timescale, and then to an average of 64 per cent at the event timescale. This research highlighted that for an upland catchment, bank erosion was an important supply of suspended sediment, and that for some flood events bank erosion can supply more sediment than is transported. © 1997 John Wiley & Sons, Ltd.     

Suspended sediment monitoring in alluvial gullies: A laboratory and field evaluation of available measurement techniques

Gully erosion is a significant source of fine suspended sediment (<63 μm) and associated nutrient pollution to freshwater and marine waterways. Researchers, government agencies, and monitoring groups are currently using monitoring methods designed for streams and rivers (e.g., autosamplers, rising stage samplers, and turbidity loggers) to evaluate suspended sediment in gullies. This is potentially problematic because gullies have several hydrological features and monitoring operational challenges that differ to those of continually flowing streams and rivers (e.g., short and intense flows, high suspended sediment concentrations, and rapid scouring and aggradation). Here we present a laboratory and field-based assessment of the performance of common suspended sediment monitoring techniques applied to gullies. We also evaluate a recently-described method; the pumped active suspended sediment (PASS) sampler, which has been modified for monitoring suspended sediment in gully systems. Discrete autosampling provided data at high temporal resolution, however, it had poor collection efficiency (25 ± 10%) of coarser sediment particles (i.e., sand). Rising stage sampling, while robust and cost-effective, suffered from large amounts of condensation under field conditions (25–35% of sampler volume), due to harsh climatic conditions creating large diurnal temperature differences at the field site, thereby diluting sample concentrations and introducing additional measurement uncertainty. The turbidity logger exhibited a highly variable response when calibrated at each site with physically collected suspended sediment samples (R² = 0.17–0.83), highlighting that this approach should be used with caution. The modified PASS sampler proved to be a reliable and representative measurement method for gully sediment water quality, however, the time-integrated nature of the method limits its temporal resolution compared to the other monitoring methods. We recommend monitoring suspended sediment in alluvial gully systems using a combination of complementary techniques (e.g., PASS and RS samplers) to account for the limitations associated with individual methods.     

The role of cryptogams in runoff and erosion control on bariland in the Nepal Middle Hills of the Southern Himalaya

Cryptogams are communities of non-vascular plants that live on the soil surface. Numerous functions have been attributed to these crusts, including changes in soil fertility and nutrient status, soil hydrology and soil erosion. Most significant for this paper is the reported benefit of cryptogams in reducing soil erosion by water in semi-arid areas. However, to date there have been few attempts to understand the soil conservation value of cryptogams in subsistence agricultural systems or in humid mountain environments. This paper investigates the potential of cryptogams in soil erosion by water on agricultural hillslope terraces (bariland) in the Nepal Middle Hills of the southern monsoonal Himalaya. The research is significant because the loss of fertile topsoil is considered by some to be the biggest threat to the livelihoods of subsistence farmers in the area in the medium and long term. The current study was conducted in the field between two of the weeding events that take place under maize cover, grown in the traditional manner. Three groundcover types which represented (i) maize only (types A), (ii) maize and weed cover (types B), and (iii) maize and cryptogam cover (types C) were monitored utilizing multiple microerosion plots. Measurements of runoff and soil loss data were collected sequentially on a storm-by-storm basis throughout the monitored period from 24 July 1997 to 29 August 1997. Measurements of infiltration rates were also taken on each of the groundcover types at selected times. Results collected from the erosion plots demonstrate that runoff and soil losses over distances of <2 m can be significantly reduced by up to 50 per cent with cryptogam cover, compared to maize-only canopies. Mean runoff for all storm events sampled from plot types A, B and C were 3·4 l m⁻², 1·6 l m⁻² and 1·5 l m⁻² respectively. For soil loss, the results were 21·7 g m⁻², 11·3 g m⁻² and 10·2 g m⁻² respectively. Therefore, cryptogams would appear to offer a similar degree of protection to the soil surface from runoff and raindrop erosion, to that afforded by weed cover. Weed and cryptogam covers protect the soil surface from rainfall kinetic energies and work to preserve surface microtopographies, depressional storage and surface water detention. Terminal infiltration rates taken at the end of the monitored period showed that well developed maize- and cryptogam-covered soil surfaces (types C) have a mean terminal infiltration rate of 35·0 mm h⁻¹ compared to 44·5 mm h⁻¹ for comparable maize- and weed-covered soil surfaces (types B), and 15·5 mm h⁻¹ for maize-only soil surfaces (types A). These results show that cryptogams and weeds also have relatively higher infiltration rates than comparable maize-only covered plots, devoid of groundcover. The findings in this study may have implications for traditional weed management practices used by local hill farmers, which often destroy cryptogam soil coatings two to three times during the maize growing period. However, further work needs to be done to ascertain farmers' understandings of cryptogams. It is hoped that conservationists will benefit from incorporating cryptogams into the design of future soil erosion studies relating to development programmes. Copyright © 2001 John Wiley & Sons, Ltd.     

Peatland restoration: controls on sediment production and reductions in carbon and pollutant export

Peatlands are an important store of soil carbon, and play a vital role in global carbon cycling, and when located in close proximity to urban and industrial areas, can also act as sinks of atmospherically deposited heavy metals. Large areas of the UK's blanket peat are significantly degraded and actively eroding which negatively impacts carbon and pollutant storage. The restoration of eroding UK peatlands is a major conservation concern, and over the last decade measures have been taken to try to control erosion and restore large areas of degraded peat. This study utilizes a sediment source fingerprinting approach to assess the effect of restoration practices on sediment production, and carbon and pollutant export in the Peak District National Park, southern Pennines (UK). Suspended sediment was collected using time integrated mass flux samplers (TIMS), deployed across three field areas which represent the surface conditions exhibited through an erosion–restoration cycle: (i) intact; (ii) actively eroding; and (iii) recently re‐vegetated. Anthropogenic pollutants stored near the peat's surface have allowed material mobilized by sheet erosion to be distinguished from sediment eroded from gully walls. Re‐vegetation of eroding gully systems is most effective at stabilizing interfluve surfaces, switching the locus of sediment production from contaminated surface peat to relatively ‘clean’ gully walls. The stabilization of eroding surfaces reduces particulate organic carbon (POC) and lead (Pb) fluxes by two orders of magnitude, to levels comparable with those of an intact peatland, thus maintaining this important carbon and pollutant store. The re‐vegetation of gully floors also plays a key role in decoupling eroding surfaces from the fluvial system, and further reducing the flux of material. These findings indicate that the restoration practices have been effective over a relatively short timescale, and will help target and refine future restoration initiatives. Copyright © 2014 John Wiley & Sons, Ltd.     

Variation in the sediment deposition behind check‐dams under different soil erosion conditions on the Loess Plateau,China

To maintain a reasonable sediment regulation system in the middle reaches of the Yellow River, it is critical to determine the variation in sediment deposition behind check‐dams for different soil erosion conditions. Sediment samples were collected by using a drilling machine in the Fangta watershed of the loess hilly–gully region and the Manhonggou watershed of the weathered sandstone hilly–gully (pisha) region. On the basis of the check‐dam capacity curves, the soil bulk densities and the couplet thickness in these two small watersheds, the sediment yields were deduced at the watershed scale. The annual average sediment deposition rate in the Manhonggou watershed (702.0 mm/(km²·a)) from 1976 to 2009 was much higher than that in the Fangta watershed (171.6 mm/(km²·a)) from 1975 to 2013. The soil particle size distributions in these two small watersheds were generally centred on the silt and sand fractions, which were 42.4% and 50.7% in the Fangta watershed and 60.6% and 32.9% in the Manhonggou watershed, respectively. The annual sediment deposition yield exhibited a decreasing trend; the transition years were 1991 in the Fangta watershed and 1996 in the Manhonggou watershed (P < 0.05). In contrast, the annual average sediment deposition yield was much higher in the Manhonggou watershed (14011.1 t/(km²·a)) than in the Fangta watershed (3149.6 t/(km²·a)). In addition, the rainfalls that induced sediment deposition at the check‐dams were greater than 30 mm in the Fangta watershed and 20 mm in the Manhonggou watershed. The rainfall was not the main reason for the difference in the sediment yield between the two small watersheds. The conversion of farmland to forestland or grassland was the main reason for the decrease in the soil erosion in the Fangta watershed, while the weathered sandstone and bare land were the main factors driving the high sediment yield in the Manhonggou watershed. Knowledge of the sediment deposition process of check‐dams and the variation in the catchment sediment yield under different soil erosion conditions can serve as a basis for the implementation of improved soil erosion and sediment control strategies, particularly in semi‐arid hilly–gully regions. Copyright © 2018 John Wiley & Sons, Ltd.     

A stochastic estimation of sediment production in an urban catchment using the USLE model

The goals of this study were to map the spatial distribution of sediment production and to estimate the probability of this production at the waterline based on a high potential of silting. The RUSLE-GIS model and Monte Carlo simulation were used. A sensitivity analysis of stochastic factors was performed by calculating the simple correlation coefficient. This procedure was applied to the Estrada Nova catchment, located in the city of Belém, northern Brazil, which has been subject to channel improvements and the construction of a detention basin. The results indicate that, following the urbanization and drainage improvements, there was a reduction in the annual sediment production probability, which is consistent with the dynamics in land use. The erodibility was the most sensitive factor in the sedimentation estimates. The methodology was considered an alternative to estimate sediment production in an urban catchment.     

Bank erosion of legacy sediment at the transition from vertical to lateral stream incision

Streambank erosion is a primary source of suspended sediments in many waterways of the US Atlantic Piedmont. This problem is exacerbated where banks are comprised of fine sediment produced by the intensive land use practices of early European settlers. A stream in this region, Richland Creek incises into banks comprised of three stratigraphic layers associated with historic land use: pre‐European settlement, early European agriculture and development, and water‐powered milldam operation. This study aims to identify the bank processes along a reach of Richland Creek that is eroding towards its pre‐disturbance elevation. The volume of material that has eroded along this stream since the milldam breached was calculated by differencing a reconstructed surface of the pond bed and an aerial lidar digital terrain model (DTM). Immediately downstream from the study reach, the channel is floored by bedrock and immediately upstream the rate of channel erosion approximately doubled along the longitudinal profile of Richland Creek, which indicate that the study reach spans the transition from a channel dominated by vertical incision in the upstream direction to horizontal widening in the downstream direction. The combined hydrometeorological conditions and dominant processes causing reach‐scale cut bank erosion were investigated with analyses of stream stage, precipitation, and streambank volumetric and surfaces change that was measured during nine terrestrial lidar surveys in 2010–2012. The spatial variability of erosion during a simulated precipitation event was examined in a field‐based experiment. Erosion was greatest where mill pond sediment columns detached along vertical desiccation and horizontal seepage cracks. This sediment accumulated on the bank toe throughout the study and was a source of readily‐entrained fine sediment contrary to the upper reaches where depositional accommodation space is more limited. Findings suggest that hotspots of sediment excavation progress upstream, indicating that restoration efforts should focus upon stabilizing banks at these locations. Copyright © 2015 John Wiley & Sons, Ltd.     

Modern sediment yield compared to geologic rates of sediment production in a semi‐arid basin,New Mexico: assessing the human impact

An Erratum has been published for this article in Earth Surface Processes and Landforms 29(13) 2004, 1707. In the semi‐arid Arroyo Chavez basin of New Mexico, a 2·28 km² sub‐basin of the Rio Puerco, we contrasted short‐term rates (3 years) of sediment yield measured with sediment traps and dams with long‐term, geologic rates (～10 000 years) of sediment production measured using ¹⁰Be. Examination of erosion rates at different time‐scales provides the opportunity to contrast the human impact on erosion with background or geologic rates of sediment production. Arroyo Chavez is grazed and we were interested in whether differences in erosion rates observed at the two time‐scales are due to grazing. The geologic rate of sediment production, 0·27 kg m^?2 a^?1 is similar to the modern sediment yields measured for geomorphic surfaces including colluvial slopes, gently sloping hillslopes, and the mesa top which ranged from 0·12 to 1·03 kg m^?2 a^?1. The differences between modern sediment yield and geologic rates of sediment production were most noticeable for the alluvial valley ?oor, which had modern sediment yields as high as 3·35 kg m^?2 a^?1. The hydraulic state of the arroyo determines whether the alluvial valley ?oor is aggrading or degrading. Arroyo Chavez is incised and the alluvial valley ?oor is gullied and piped and is a source of sediment. The alluvial valley ?oor is also the portion of the basin most modi?ed by human disturbance including grazing and gas pipeline activity, both of which serve to increase erosion rates. Copyright © 2004 John Wiley & Sons, Ltd.     

Distributed discharge and sediment concentration predictions in the sub‐humid Ethiopian highlands: the Debre Mawi watershed

Experimental research in the Ethiopian highlands found that saturation excess induced runoff and erosion are common in the sub‐humid conditions. Because most erosion simulation models applied in the highlands are based on infiltration excess, we, as an alternative, developed the Parameter Efficient Distributed (PED) model, which can simulate water and sediment fluxes in landscapes with saturation excess runoff. The PED model has previously only been tested at the outlet of a watershed and not for distributed runoff and sediment concentration within the watershed. In this study, we compare the distributed storm runoff and sediment concentration of the PED model against collected data in the 95‐ha Debre Mawi watershed and three of its nested sub‐watersheds for the 2010 and 2011 rainy seasons. In the PED model framework, the hydrology of the watershed is divided between infiltrating and runoff zones, with erosion only taking place from two surface runoff zones. Daily storm runoff and sediment concentration values, ranging from 0.5 to over 30 mm and from 0.1 to 35 g l^?1, respectively, were well simulated. The Nash Sutcliffe efficiency values for the daily storm runoff for outlet and sub‐watersheds ranged from 0.66 to 0.82, and the Nash–Sutcliffe efficiency for daily sediment concentrations were greater than 0.78. Furthermore, the model uses realistic fractional areas for surface and subsurface flow contributions, for example between saturated areas (15%), degraded areas (30%) and permeable areas (55%) at the main outlet, while close similarity was found for the remaining hydrology and erosion parameter values. One exception occurred for the distinctly greater transport limited parameter at the actively gullying lower part of the watershed. The results suggest that the model based on saturation excess provides a good representation of the observed spatially distributed runoff and sediment concentrations within a watershed by modelling the bottom lands (as opposed to the uplands) as the dominant contributor of the runoff and sediment load. Copyright © 2014 John Wiley & Sons, Ltd.