均匀流场中并列圆柱涡激振动的现状与预测

并列圆柱体在均匀流场中的涡激振动十分复杂，但又广泛存在于实际工程之中。当两柱在流体激励作用下产生振动时，由于同时存在着流固耦合作用和柱间干扰作用，而使周围流场变得更加复杂。本文对并列刚性和弹性圆柱的流场分类，Ｓｔｒｏｕｈａｌ数及流体载荷等问题进行了综述，在此基础上提出了进一步研究的建议。     

Study of non-linear wave motions and wave forces on ship sections against vertical quay in a harbor

The resonance phenomenon of fluid motions in the gap between ship section, seabed and vertical quay wall is studied numerically and experimentally. The natural frequency of the fluid motions in the gap is derived. A two-dimensional time-domain coupled numerical model is developed to calculate the non-linear wave forces acting on a ship section against vertical quay in a harbor. The fluid domain is divided into an inner domain and an outer domain. The outer domain is the area between the left side of ship section and the incident boundary, where flow is expressed by Boussinesq equations. The rest area is the inner domain, which is the domain beneath the ship section plus the domain between the right side of ship section and vertical quay wall. The flow in the inner domain is expressed by Newton's Second Law. Matching conditions on the interface between the inner domain and the outer domain are the continuation of volume flux and the equality of pressures. The numerical results are validated by experimental data.     

Numerical Simulation of Residual Circulation due to Bottom Roughness Variability Under Tidal Flows in A Semi-Enclosed Bay

1 .IntroductionWater pollution has a large influence on water environment and our life ;for example ,it some-times induces oxygen depression,blue tide andredtide in a bay.For water purificationin a semi-en-closed sea ,some new methods to activate the tidal exchange between an inner bay and an outer seaarea by control of a tidal residual current have been proposed (Awayaet al .,1995) . Huthnance(1973) ,Zimmerman (1978 ,1981) , Loder (1980) ,and Robinson (1983) considered cases wherethe fricti…     

海岛局部风场特性的风洞试验和数值模拟研究

针对海岛局部风效应突出的问题,采用边界层风洞试验与数值模拟相结合的方法,对3种坡度的理想化海岛地形的风剖面进行了数值拟合,定义了差异系数来描述风剖面变化,利用数值模拟研究了差异系数和最大加速比在迎风侧的分布,重点探讨了海岛坡度和高度对最大加速比和差异系数的影响;基于风洞数据,对迎风侧和背风侧顺风向、横风向和竖向湍流强度和阵风因子分布进行了研究。结果表明：数值模拟与风洞试验结果较接近,风剖面指数在迎风侧较小;靠近坡顶的加速效应尤为明显,其最大加速比为0.4～1.0;坡腰处的差异系数较小,随着岛脊线角度的增加,差异系数为0的位置有向坡脚靠近的趋势;坡度增大到25°、0°岛脊线上最大加速比和差异系数均较大;迎风侧的三向湍流强度分布较规律,而背风侧的三向湍流强度分布较杂乱,尤其是在距海岛表面100 m高度范围内;阵风因子和湍流强度的变化趋势具有较高的一致性。     

聚焦波浪在浅堤上传播变形高精度数值模拟研究

基于开源程序REEF3D,通过建立高精度二维数值波浪水槽,系统研究了聚焦波浪在浅堤上传播变形的规律,着重分析了聚焦波浪通过浅堤的水动力过程及能量变化规律,讨论了不同波浪要素对聚焦波浪传播特性的影响。除此之外,还考虑了双浅堤布置对聚焦波浪传播变形的影响。研究结果表明:极端波浪通过浅堤时,堤顶水深越小,波浪主频能量衰减越显著。在给定堤顶水深条件下,聚焦点与浅堤的相对位置对聚焦波浪能量的衰减影响较小。在双浅堤布置条件下,随着浅堤间距的增加,上下游浅堤的相互影响逐渐减弱,高频段的波浪能量也随之减小。     

Numerical Simulation of Sand Shoreline Evolution Under Action of Regular Waves and Irregular Waves

Based on the singleline theory, a numerical simulation is presented to predict the shoreline evolution on sand beach. A parabolic equation of longshore sediment transport and boundary conditions are proposed. The combined effect of wave diffraction and refraction on the shoreline evolution on the downdrift side of the breakwater is taken into account and is calculated using the theory of regular waves and irregular waves. The present model is verified by the field observation data of erosion for half a year on the downdrift side of a harbor, and compared with some experimental results. The numerical results are in good agreement with the field measured and experimental data.     

Installing single-propeller twin-rudder system with less asymmetric maneuvering motions

The inflow characteristics to each one of the rudders of single-propeller twin-rudder system are investigated. It is shown that this inflow is not parallel to ship's centerline. This may result in asymmetric maneuvering characteristic of the ship thereby reducing ship's maneuvering performance. For this purpose, a method of installing single-propeller twin-rudder system is proposed. This method is called “virtual zero rudder angle” arrangement. Here, each one of the twin-rudder is set at an angle corresponding to the inflow to the rudder. The improvement in ship's maneuvering characteristics with “virtual zero rudder angle” arrangement is investigated using experiments and numerical simulations for different ship types. It is shown that this arrangement may also improve ship's propulsion performance.     

Study on the Configuration of Towed Flexible Cables

Based on the fundamental equation of flexible cable dynamics for a towed system, an easily solved mathematical model is set up in this paper by means of appropriate simplification. Several regular patterns of spatial motion of towed flexible cables in water are obtained through numerical simulation with the finite difference method, and then modification and verification by trial results at sea. A technical support is provided for the towing ship to maneuver properly when a flexible cable is towed. Furthermore, the relations between two towed flexible cables, which are towed simultaneously by a ship, are investigated. The results show that the ship towing two flexible cables is safe under the suggested arrangement of two winches for the towing system, and the coiling/uncoiling sequences of the cables as well as the suggested way of maneuvering.     

Study on Failure Mechanism and Bearing Capacity of Three-Dimensional Rectangular Footing Subjected to Combined Loading

This paper presents two kinematic failure mechanisms of threc-dimensional rectangular footing resting on homogeneous undrained clay foundation under uniaxial vertical loading and uniaxial moment loading. The failure mechanism under vertical loading comprises a plane strain Prandti-type mechanism over the central part of the longer side, and the size of the mechanism gradually reduces at the ends of the longer side and over the shorter side as the corner of rectangular footing is being approached where the direction of soil motion remains normal to each corresponding side respectively. The failure mechanism under moment loading comprises a plane strain scoop sliding mechanism over the central part of the longer side, and the radius of scoop sliding mechanism increases linearly at the ends of the longer side. On the basis of the kinematic failure mechanisms mentioned above, the vertical ultimate bearing capacity and the ultimate bearing capacity against moment or moment ultimate bearing capacity are obtained by use of upper bound limit analysis theory. At the same time, numerical analysis results, Skempton＇ s results and Salgado et al. ＇s results are compared with this upper bound solution. It shows that the presented failure mechanisms and plastic limit analysis predictions are validated. In order to investigate the behaviors of undrained clay foundation beneath the rectangular footing subjected to the combined loadings, numerical analysis is adopted by virtue of the general-purpose FEM software ABAQUS, where the clay is assumed to obey the Mohr-Coulomb yielding criterion. The failure envelope and the ultimate bearing capacity are achieved by the numerical analysis results with the varying aspect ratios from length L to breadth B of the rectangular footing. The failure mechanisms of rectangular footing which are subjected to the combined vertical loading V and horizontal loading H （Vertical loading V and moment loading M, and horizontal loading H and moment loading M respectively are observed in the finite e     

不同布设间距和来流速度下方型人工鱼礁上升流效应的数值模拟

合理的人工鱼礁组合可以有效改善投放水域的流场效应,提高投放水域底层与上层水体之间的扰动。通过使用并行大涡模拟模式及被动示踪物模块,并通过调整人工鱼礁布设间距,研究了在不同背景流速条件(0.1、0.5、0.6和1.0 m/s)下,在不同的横向间距(1L、2L、3L)(L表示人工鱼礁的边长)或纵向间距(1L、2L、3L、4L、5L)情况下,方型人工鱼礁对上升流体积、营养盐的抬升和垂向涡黏系数的影响。研究结果表明,在同一布置条件下,单排布置下的三块人工鱼礁形成的上升流体积大小与来流速度成正相关,体积随来流流速增加而增大6.4%～80.5%;在同一流速条件下,上升流体积大小与纵向布置的间距成正比,与横向布置的间距成反比;在横向布置条件下,当来流速度为1.0 m/s、布设间距为1L时,上升流体积参数最佳。总体来说,上升流体积参数、示踪物浓度差和垂向涡黏性系数均显示横向布置优于纵向布置,相较于布设间距,来流速度是影响上升流体积最重要的因素。     

多向不规则波作用下九桩群桩效应试验研究

小尺度群桩应用广泛,一直是学者研究的重点,小尺度有别于大尺度桩柱,由于桩柱周围存在漩涡的脱落,使得受力特性复杂。以往的研究过程中,波浪主要采用单向不规则波浪,并且试验模型多以两桩或三桩组成的群桩结构为主,桩数相对较少。多向不规则波与群桩结构的作用特点有别于单向不规则波且研究较少。通过物理模型试验,针对多向不规则波对于9桩桩排群桩结构的作用进行了研究。首先综合考虑KC1/3数和相对桩径的影响,提出以参数KCLD 1/3数来衡量群桩的效应,并分析了正向力与横向力随着参数KCLD 1/3数和相对桩距的变化关系,研究了群桩中不同桩位桩柱波浪力的变化规律和方向分布宽度对于群桩波浪力的影响。研究结果表明,群桩中各桩的正向力随着方向分布标准差的增大而减小,而横向力在相对桩距较大时随着方向分布标准差的增大而增大,同时群桩中不同位置桩上的波浪力具有较大的差异。     

Propagation of solitary waves over a submerged permeable breakwater

We study the interactions between a non-breaking solitary wave and a submerged permeable breakwater experimentally and numerically. The particle image velocimetry (PIV) technique is employed to measure instantaneous free surface displacements and velocity fields in the vicinity of a porous dike. The porous medium, consisting of uniform glass spheres, is mounted on the seafloor. Due to the limited size of each field of view (FOV) for high spatial resolution purposes, four FOVs are set in order to form a continuous flow field around the structure. Quantitative mean properties are obtained by ensemble averaging 30 repeated instantaneous measurements. The Reynolds decomposition method is then adopted to separate the velocity fluctuations for each trial to estimate the turbulent kinetic energy. In addition, a highly accurate two-dimensional model with the volume of fluid interface tracking technique is used to simulate an idealized volume-averaged porous medium. The model is based on the Volume-Averaged Reynolds Averaged Navier–Stokes equations coupled with the non-linear k–ε turbulence closure solver. Comparisons are performed between measurements and numerical results for the time histories of the free surface elevation recorded by wave gauges and the spatial distributions of free surface displacement with the corresponding velocity and turbulent kinetic energy around the permeable object imaged by the PIV system. Fairly good agreements are obtained. It is found that the measured and modeled turbulent intensities on the weather side are much larger than those on the lee side of the object, and that the magnitude of the turbulent intensity increases with increasing wave height of a solitary wave at a constant water depth. The verified numerical model is then used to estimate the energy reflection, transmission and dissipation using the energy integral method by varying the aspect ratio and the grain size of the permeable obstacle.     

SOME THEORETICAL PROBLEMS ON MODE FILTERING IN SHALLOW WATER

Since the mode filtering is a certain sort of "space filtering", the matter of the utmost concern s the "side lobe" produced by some simplified processing in practice instead of the ideal orthogonal operation. In this paper, the following problems are discussed theoretically: (1) "side lobe" produced by using an integration in the water column instead of halfspace; (2) "side lobe" produced by using a finite discrete sampling; (3) "side lobe" produced by a hard-clipped eigenfunction; and (4) "side lobe" produced by the inclination of the vertical array. Some analytic results and numerical examples are shown for a special case in which the sound speed profile is isovelocity in the water column. It is found that the effect of array inclination is serious and an approach of phase compensation in proposed.     

On the side wall effects upon bodies of arbitrary geometry in wave tanks

A numerical model based on using a tank Green function, has been developed to compute the side wall effects on first- and second-order loadings upon bodies of arbitrary geometry in wave tanks. This tank Green function (TGF) is composed of a finite series of open-sea Green functions and an asymptotic part represented by two single integrals whose kernels decrease exponentially with the integral variable. This consistent expression of the TGF permits one to highlight the side wall effects and to give some criteria for the choice of tank width and the measurement duration to limit the reflection of diffraction and radiation waves.

The efficiency of the developed model is shown in the application to hemispheres and a box-shaped barge placed in the center of the wave tanks. The numerical results explain well the irregularities in the experimental measurements and show that the side walls have important effects on the first-order quantities. These effects are much more pronounced on the second-order drift loads.     

Second sea－entering approach of Changjiang River： Tongl Canal－planning of control dimensions， analysis of erosion and siltation and selection of outlet

Ｓｅｃｏｎｄｓｅａ－ｅｎｔｅｒｉｎｇａｐｐｒｏａｃｈｏｆＣｈａｎｇｊｉａｎｇＲｉｖｅｒ：ＴｏｎｇｌＣａｎａｌ－ｐｌａｎｎｉｎｇｏｆｃｏｎｔｒｏｌｄｉｍｅｎｓｉｏｎｓ，ａｎａｌｙｓｉｓｏｆｅｒｏｓｉｏｎａｎｄｓｉｌｔａｔｉｏｎａｎｄｓｅｌｅｃｔｉｏｎ...     

Experimental and numerical investigation of a freefall wedge vertically entering the water surface

Experiments and numerical methods are developed to investigate the water entry of a freefall wedge with a focus on the evolution of the pressure on the impact sides (the side contacting water) and the top side (the dry side on the top of the wedge), evolution of the global hydrodynamic loads, evolution of the air–water interface, and wedge motion. It is found that a typical water entry of a freefall wedge can be divided into slamming, transition, collapse and post-closure stages. A single-fluid numerical model is presented to simulate the first three stages. The results are compared to experiments and good agreements are obtained. A two-fluid BEM is proposed to investigate the influence of the air flow before the closure of the cavity created on the top of the wedge. It is found that for the closure of the 2D cavity, the air flow starts to play an important role just before closure but due to the short duration, the influence of air flow on the body velocity and configuration of the air–water interface is limited.     

海洋对热带气旋响应的一种改进模式

建立一个改进的二层非线性原始方程海洋模式，研究海洋对热带气旋的响应。采用湍流动能收支参数化风应力产生的垂直混合（夹卷），其中考虑了盐度对层结强度的影响。通过海洋对７００２号台风响应的数值模拟，结果表明，在引起海表温度下降的各热通量分量中，夹卷约占了８３％，余下的海表面热通量占了１７％。在台风路径转向的右侧，海洋出现强烈的降温，表现出明显的右偏性。降温的幅度、范围和形状均与观测结果较为一致。     

On the determination of the mesh size for numerical simulations of shock wave propagation in near field underwater explosion

It is well known that the accuracy of mesh-based numerical simulations of underwater explosion strongly relies on the mesh size adopted in the analyses. Although a numerical analysis of underwater explosion can be performed with enough accuracy by using considerably fine meshes, such fine meshes may lead to substantially increase in the CPU time and the usage of computer memory. Thus, how to determine a suitable mesh size in numerical simulations is always a problem confronted when attempting to study the shock wave propagation resulting from underwater explosion and the subsequent response of structures. Considering that there is currently no universally accepted method for resolving this problem, this paper aims to propose a simple method to determine the mesh size for numerical simulations of near field underwater explosion. To this end, the mesh size effects on the shock wave propagation of underwater explosion are carefully investigated for different charge weights, through which the correlation between mesh sizes and charge weights is identified. Based on the numerical study, a dimensionless variable (λ), defined as the ratio of the radius of charge to the side length of element, is introduced to be the criterion for determining the mesh size in simulations. It is interesting to note that the presented method is suitable for various charge weights. By using the proposed meshing rule, adequate balance between solution accuracy and computational efficiency can be achieved for different blast scenarios in numerical simulations of underwater explosion.     

Experimental and numerical hydrodynamic analysis of a stepped planing hull

This work addresses the experimental and numerical study of a stepped planing hull and the related fluid dynamics phenomena typically occurring in the stepped hull in the unwetted aft body area behind the step. In the last few years, the interest in high-speed planing crafts, with low weight-to-power ratios, has been increasing significantly, and, in such context, naval architects have been orienting toward the stepped hull solution. Stepped planing hulls ensure good dynamic stability and seakeeping qualities at high speeds. This is mainly due to the reduction of the wetted area, which is caused by the flow separation occurring at the step. This paper presents the experimental results of towing tank tests in calm water on a single-step hull model, which is the first model of a new systematic series. The same flow conditions are analyzed via Reynolds Averaged Navier-Stokes (RANS) and Large Eddy Simulations (LES), with different moving mesh techniques (overset/chimera and morphing grid), performed at different model speeds. The numerical results are in accordance with experimental data, and overset/chimera grid is found to be the best approach between the analyzed ones. The flow patterns obtained numerically through LES on a refined grid appear similar to the ones observed in towing tank investigations through photographic acquisitions. These flow patterns are dominated by a rather complex 3D arrangement of vortices originating from air spillage at both sides of the step. The understanding of these phenomena is important for the effectiveness of stepped hull designs.     

非淹没刚性植物对海啸作用下海堤水动力特性影响数值模拟研究

基于非静压单相流模型NHWAVE建立了高精度数值波浪水槽。通过设计不同的计算工况,系统研究了非淹没刚性植物对海啸作用下海堤周围水动力特性的影响。着重分析了不同入射波高、不同植物分布密度以及不同植物分布宽度条件下海啸波沿程波形特征以及海堤堤顶越浪流空间分布特征。结果表明:不同入射波高、植物分布密度以及植物宽度条件下,堤顶流厚度和水体流速具有明显单调的变化趋势,并且随着植物分布密度和宽度增大,波能衰减增大;随着入射波非线性增强,植物分布密度和分布宽度对堤顶前段水流厚度的影响也随之增强,而对堤顶后段水流厚度的影响则减弱,且堤顶后缘水流厚度约为堤顶前缘厚度的二分之一;在波浪非线性较大情况下,植物的存在对堤顶流速度的空间分布趋势几乎没有影响,但相对堤顶流速度增加程度均大于无植物情况,且堤顶后缘水流速度约为堤顶前缘的1.6倍。