Mapping urban heat islands of arctic cities using combined data on field measurements and satellite images based on the example of the city of Apatity (Murmansk Oblast)

This article presents the results of a study of the urban heat island (UHI) in the city of Apatity during winter that were obtained according to the data of field meteorological measurements and satellite images. Calculations of the surface layer temperature have been made based on the surface temperature data obtained from satellite images. The experimental data on air temperature were obtained as a result of expeditionary meteorological observations, and the experimental data on surface temperature were obtained based on the data of the space hyperspectral Moderate-Resolution Imaging Spectroradiometer (MODIS) system, channels 31 and 32 (10.78–11.28 and 11.77–12.27 micrometers, respectively). As a result of the analysis of temperature fields, an intensive heat island (up to 3.2°C) has been identified that was estimated based on the underlying surface temperature, and its mean intensity over the observation period significantly exceeds the representative data for European cities in winter. It has also been established that the air temperature calculated according to the MODIS data is systematically higher under winter conditions than the air temperature from direct measurement data.     

协同克里格方法在东海表面温度场数据插值中的应用

首次将协同克里格方法引入到海洋水文插值计算中处理东海实验区2008-01—2008-03三个月抽稀后的月平均海表面温场数据。将温场数据分为趋势分量和剩余分量,最终采用两分量的估计值之和实现海表面温场数据的格网插值估计。结果表明：协同克里格方法比传统方法（趋势分析、移动平均、普通克里格插值）效果好。提出变差函数局部拟合的...     

海洋天然气水合物合成的模拟实验研究

为了研究海洋天然气水合物生成过程中元素的地球化学行为,研制了一套天然气水合物实验装置和一套实验流程.利用这套实验装置,在天然海水-甲烷体系中合成天然气水合物.探讨了不同影响因素,包括温度、压力、振动、过滤方式等对天然气水合物合成实验结果的影响.     

外延铁电薄膜相变温度的尺寸效应

考虑外延钙钛矿型铁电薄膜内的等效应力、表面晶格变化和表面电荷引起的退极化效应等机电耦合边界条件,利用铁电薄膜系统的动态金茨堡-朗道方程(DGL),系统分析和讨论了外延铁电薄膜相变温度与临界相变厚度的尺寸效应.结果表明,铁电薄膜相变温度与临界相变厚度完全依赖于各种与薄膜厚度相关的力电耦合边界条件.也给出了BaTiO₃外延铁电薄膜相变温度在各种边界条件下随厚度的变化,从结果看出,本文的分析与结论更符合实验数据.     

Sea ice growth at nonstationary ocean-atmosphere heat exchange

A thermodynamic model of sea snow-ice cover growth under the influence of heat flows on its upper and lower surfaces is presented. The growing is described with an extended region of phase transition (a two-phase region) with a linear temperature distribution. The temperature of the upper surface is calculated with the use of a heat-balance equation on the basis of determinable meteorological observation data. The comparison of the model results with freezing experimental data is performed.     

Analysis of Thermal Transfer of Reinforced Concrete Submarine Oil Tanks

-The temperature distributions obtained by different methods of analysis for solving thermal transfer of reinforced concrete (R. C.) submarine oil tanks (RCSOT), including flat wall method, cylinder wall method and finite element method, are compared with the experimental data of thermal transfer of RCSOT. The precision and scope of applicability of different methods are discussed. The principle for selecting analysis method for solving thermal transfer of RCSOT is given. The analytical and experimental temperature distributions show that the wall of RCSOT should consist of double walls and empty space between them should be filled with sand or other heat insulation materials to reduce the temperature difference of the wall and to prevent concrete from cracking.     

基于GPRS的海水温度和盐度自动监测系统

基于GPRS的海水温度和盐度自动监测系统综合应用现代通信技术、计算机技术和传感器技术,实现了对海水盐度和温度的自动监测,从而实现了工业现场数据实时上网,监测人员在任何时间、任何能接入In ternet的地点都可以浏览到现场数据。真正实现了无纸记录,极大地减轻了监测人员的劳动强度,避免了在检测过程中的人为误差和可能出现的危险。     

A numerical model for the evaluation of the depth of penetration of two-dimensional turbulent convection

For a one type of temperature turbulent convection observed in the ocean, i.e., for the two-dimensional roller-type convection, we propose a model intended for the evaluation of the intensity and depth of penetration of convective motions as functions of a given heat flow from the sea surface and the temperature gradient in the thermocline. This model is based on the methods of the theory of turbulent jets and experimental data on the vertical distribution of temperature in the course of convection. The comparison of the calculated dimensionless values of the depth of penetration of the thermocline in autumn and winter shows a good qualitative agreement with the data ofin situ measurements. Translated by Peter V. Malyshev and Dmitry V. Malyshev     

赤潮藻类温度生态幅的定量表达模型研究

首先在Moisan的温度和比生长率关系基础上,依据Shelford耐受性定律,建立了赤潮藻类温度生态幅(最适温度、适温范围、耐受范围)的定量表达模型。同时,依据此模型可定量导出赤潮藻类的生物学零度。其次,结合实验培养数据,建立了东海原甲藻比生长率的温度响应模式,并利用研究结果定量得到该藻种的温度生态幅,这与已有的实验研究和现场监测结果有较好的一致性。     

结合注意力机制的区域型海表面温度预报算法

海表面温度预报在海洋相关领域具有重要的实用价值,随着遥感信息采集技术的不断发展和完善,区域内海表面温度数据采集的完整性得到了保障。现今大多数方法在预报海表面温度时,只考虑了海表面温度的时间相关性,并未利用其空间相关性,使得预报精度受到限制。针对该问题,本文将区域内每天的海表面温度数据作为一个矩阵输入模型,便于时间和空间信息的提取,并提出了CA-ConvLSTM模型来预报海表面温度。该模型首先利用卷积层对海表面温度矩阵进行局部特征提取,然后通过注意力模型为矩阵序列分配权重,将权重与矩阵序列对应相乘得到加权特征序列,最后,利用ConvLSTM进行预报,获得未来一天或五天内的海表面温度。通过实验确定模型的结构、输入尺寸和k值,再将CA-ConvLSTM与SVR、LSTM和ConvLSTM进行对比。实验结果表明:CA-ConvLSTM的均方根误差(Root Mean Square Error,RMSE)和预报精度(Prediction Accuracy,PACC)指标均要优于其他三种预报方法,验证了本文方法的有效性。     

Spark平台下的海表面温度并行预测算法

面对海量的海表面温度数据,如何使用大数据处理平台和新的处理技术来实时处理、分析并预测海表面温度数据,是一个亟待解决的问题。本文基于现阶段的时间序列方法和专家意见,首先,将类比合成方法引入到海表面温度预测应用中;其次,基于Spark平台提出了一种改进的快速DTW算法SparkDTW;最后,为了充分利用通过时间序列挖掘得到的信息,将SparkDTW与SVM相结合,提出了SparkDTW+SVM混合模型,为海表面温度预测的应用研究提供了较好的理论基础和技术支持。实验结果表明,SparkDTW算法预测精度优于SVM,提高了海表面温度预测效率,验证了将类比合成方法应用在海表面温度预测的可行性;SparkDTW+SVM在精度方面要优于SparkDTW和SVM,表明SVM模型能充分利用时间序列挖掘的信息,验证了SparkDTW+SVM在海表面温度预测的有效性。     

温盐深变化对波束脚印坐标的影响规律分析

在多波束测深中,温盐深剖面数据的准确性对测量精度起到非常重要的作用,而在实际测量中,温盐深误差又不可避免地存在。为了分析温盐深变化对波束脚印坐标的影响规律并将其影响值量化,本文在声速剖面间接测量数据的基础上,选择精度较高、适应性较强的声速经验公式推导其误差公式,计算温盐深变化所引起的声速误差值,并且在常梯度声线跟踪模型的基础上推导出声波旅行轨迹的水平位移和垂直位移误差公式,然后结合声速剖面计算出声速误差对波束脚印坐标的影响程度。实验结果表明,温度变化对声速的影响最大,盐度和深度依序次之;温度、盐度、深度3个参量的变化引起波束脚印Z坐标的变化量均大于X、Y坐标,最高可达变化前深度的0.6%。温度和盐度的变化引起的三轴坐标值变化量随入射角的增大而减小,而深度变化引起的三轴坐标值变化量几乎不随入射角的变化而变化。本文研究结果可为温盐深误差对多波束测深精度评估工作提供借鉴作用。     

Growth Aspects and Magnesium Carbonate Concentrations of the Reef Building Octocoral Heliopora coerulea (Pallas) after Transplantation

Abstract. An experiment to test C have's hypothesis on temperature dependent MgCO₃ concentrations in marine calcareous skeletons was undertaken by transplanting colonies of Heliopora coerulea. The corals were transferred from a shallow lagoon with high average temperatures to the outer bottom of a fringing reef, 16 m depth, with low average temperatures. Against expectation, a statistically significant increase of average mol % concentrations from 0.48 to 0.54 % for upper growth regions and from 0.49 to 0.62% for lower growth regions was obtained. Temperature records during the experimentation period and the above data indicate that the mol% MgCO₃ concentration in the skeleton of living Heliopora colonies increases when transplanted to an environment with a lower temperature average than that of their original growth site, and with seasonal temperature fluctuations which are smaller in the experimental site than in the control site. Temperature fluctuations at the control site were up to 2.5 times greater than at the experimental site for most of the observation months. This supports the conclusion that the parameters a) minimum temperature and b) temperature stability of the environment are essential for the incorporation of Mg into the carbonate skeleton matrix of marine organisms. Within this study the results of a quantitative chemical analysis of the carbonate skeleton of H. coerulea are presented and growth data of transplanted colonies compared with those from the control site.     

A growth model for a hyalid amphipod Hyale perieri in the coastal water of Alexandria (Egypt)

Abstract-The growth rate of the hyalid amphipod Hyale perieri was studied on the bases of Ikeda'sgrowth model which is based on the inter moult period (IP) and moult increament (ΔBL). To applythis approach, laboratory experiments were carried out at three temperatures regimes (15℃, 20℃,25℃) to gain accurate data of IP and BL. The total number of specimens used in this study was 86 at15℃, 24 at 20℃ and 70 at 25℃. The number of flagellar segments of both antennae of the Hyaleperieri could not be used as an index of growth (instar criterion). The obtained results indicated that,the predicted IP of the specimens was inversely related to temperature and in good agreement with theobserved values at the experimental temperatures. IP data obtained from laboratory-reared specimes arecombined with ΔBL data to establish a growth model for Hyale perieri from its release from the mar-supium (1.64 mm BL) to the maximum size (12.67 mm BL) as a function of temperature. The maxi-mum numbers of consecutive moults     

Temperature fluctuations in the atmospheric surface layer over the thermally inhomogeneous underlying surface

The influence of both spatial and temporal temperature inhomogeneities of the underlying surface on the temperature field in an unstably stratified atmospheric surface layer is considered. The methods of correlation and spectral analyses are proposed to estimate statistical characteristics of surface-air temperature fluctuations caused by both turbulent mixing and inhomogeneities in the temperature of the underlying surface. Analysis of experimental data obtained from measurements in the atmospheric surface layer yields estimates for the contribution made by the time-dependent thermal properties of the underlying surface to the total variance of air-temperature fluctuations. It is shown that the additional air-temperature fluctuations generated by surface-temperature inhomogeneities and unrelated to shear flow may reach 70% and 30% of the total variance of measured fluctuations under variable cloudiness and clear skies, respectively. For the height z = 2 m within the wave-number range 2 × 10^?3 rad m^?1 < k < 0.1 rad m^?1, the contribution made by a spatial surface-temperature inhomogeneity to the variance of air-temperature fluctuations does not exceed 10% of the total variance. Correlation and spectral analyses of experimental data make it possible to isolate the spectra of properly turbulent fluctuations from the measured fluctuations and thus to obtain more accurate values of the universal function of similarity theory for temperature in the range of small wave numbers beyond the inertial range.     

Study on topographic compensation model of the Okinawa Trough Ⅱ. Geological interpretation of isostatic response function of the Okinawa Trough

INTRODUCTION' Regional isostatic model(Vening Meinesz, 1941 )considered the lithosphere as a loaded elasticplate floating on astherosphere, and the topographical load was supPOrted by elastic stress of theplate, then compensation would be accomplished in a wider regional extent. When the thicknessof elastic plate is certain, the increase of topographic load will cause the elastic plate to be downward fie-cure and the crust thickened. The isostatic resPOnse function, i. e. experimental i…     

SZC15-4型多参数剖面仪设计

CTD是测量海水温度、电导率和压力的仪器,在海洋科学考察、海洋资源调查开发、海洋环境监测预报和海洋军事研究中应用广泛。SZC15-4型多参数CTD是国产SZC15系列CTD最新型号,用于测量海水的温度、电导率、深度和叶绿素浓度,适用于近岸海洋调查。文中介绍了SZC15-4型多参数CTD剖面仪的性能、工作原理、系统组成和工作流程。并通过海上试验,与SBE19CTD在相同环境条件、相同采样速率下作比测,通过对实验数据做相关运算得出SZC15-4型CTD与SBE19在温度、盐度相关性优于0.999 9,表明两种仪器具有很高的相关特性。     

HJ-1B 卫星海表温度定量反演业务化算法研究——以中国北部海区为例

利用中国2008年9月发射的自主 HJ-1B 卫星热红外遥感影像数据,基于实测数据对已有海表温度反演的单窗算法进行了改进与简化,重新订正了大气透射率和大气平均作用温度估算方程,建立了基于实测数据验证的 HJ-1B 卫星海表温度定量反演业务化算法.将本算法与段四波等的改进算法用于实验海区海表温度的反演,反演结果与卫星同步实测海温数据的对比表明:本研究算法反演结果与现场同步实测海表温度平均误差约为0.76,℃段四波等改进算法反演结果平均误差约为1.09℃.本算法为 HJ-1B 卫星海表温度产品的业务化应用提供了便捷可行的方案     

高温环境中主管轴力对焊接圆钢管T节点承载性能的影响

利用有限元软件ABAQUS建立T型圆钢管节点热传导分析模型,通过与已有试验数据进行对比,验证了所建有限元模型的可靠性。利用提出的有限元模型分析了不同主管轴力作用下的T型圆钢管节点在火灾环境中的失效过程,研究了主管轴力对T型圆钢管节点临界温度的影响规律。分别讨论了采用屈服强度折减和弹性模量折减的方法预测T型圆钢管节点在高温下的极限承载力,并将预测结果和有限元分析结果进行了对比,给出了这两种方法用于工程设计时的建议。