Catalytic Reduction of Hexaminecobalt(III) by Pitch‐based Spherical Activated Carbon (PBSAC)

The wet ammonia (NH₃) desulfurization process can be retrofitted to remove nitric oxide (NO) and sulfur dioxide (SO₂) simultaneously by adding soluble cobalt(II) salt into the aqueous ammonia solution. Activated carbon is used as a catalyst to regenerate hexaminecobalt(II), Co(NH₃), so that NO removal efficiency can be maintained at a high level for a long time. In this study, the catalytic performance of pitch‐based spherical activated carbon (PBSAC) in the simultaneous removal of NO and SO₂ with this wet ammonia scrubbing process has been studied systematically. Experiments have been performed in a batch stirred cell to test the catalytic characteristics of PBSAC in the catalytic reduction of hexaminecobalt(III), Co(NH₃). The experimental results show that PBSAC is a much better catalyst in the catalytic reduction of Co(NH₃) than palm shell activated carbon (PSAC). The Co(NH₃) reduction reaction rate increases with PBSAC when the PBSAC dose is below 7.5 g/L. The Co(NH₃) reduction rate increases with its initial concentration. Best Co(NH₃) conversion is gained at a pH range of 2.0–6.0. A high temperature is favorable to such reaction. The intrinsic activation energy of 51.00 kJ/mol for the Co(NH₃) reduction catalyzed by PBSAC has been obtained. The experiments manifest that the simultaneous elimination of NO and SO₂ by the hexaminecobalt solution coupled with catalytic regeneration of hexaminecobalt(II) can maintain a NO removal efficiency of 90% for a long time.     

Regulating Environmental Factors of Nutrients Release from Wheat Straw Biochar for Sustainable Agriculture

One mechanism by which biochar application enhances soil nutrient availability is through direct nutrients release from biochar. However, factors controlling the release processes are poorly understood. In this study, the effects of pH, biochar to water ratio, temperature, ionic strength, and equilibration time on the release of PO, NO, NH, K⁺, Na⁺, Ca²⁺, and Mg²⁺ from biochar were evaluated in simulated experiments. The release of PO, K⁺, Ca²⁺, and Mg²⁺ was significantly affected by extraction pH, suggesting that their release from biochar was pH dependent or an H⁺‐consuming process. Correlation analysis indicated that PO and Ca²⁺, PO and Mg²⁺, and Ca²⁺ and Mg²⁺ were co‐solubilized with increasing soil acidity. To a lesser extent, the recovery of the nutrients was also affected by the ratio of biochar to water: more nutrients were soluble with more water supply. In contrast, the release of Na was not affected by pH while the concentration increased with decreasing biochar to water ratio. Meanwhile, other factors (temperature, ionic strength, and equilibration time) had less effect on nutrient release from biochar. Under the influence of pH, the patterns of NO and PO release from biochar were different: extractable NO concentration was not affected by the pH but more PO was released in strongly acidic conditions. Our data suggested that P was mainly retained in inorganic forms while N was in organic forms in biochar. We conclude that environmental factors have marked influences on nutrients release from biochar.     

Evaluation of Near‐Critical Overdamping Effects in Slug‐Test Response

A slug test behaves as a harmonic oscillator, subject to both inertial effects and viscous damping. When viscous and inertial forces are closely balanced, the system is nearly critically damped, and water‐level recovery is affected by inertial effects, but does not exhibit oscillation. These effects were investigated by use of type curves, generated both by modification of Kipp's (1985) computer program and by use of the Butler‐Zhan (2004) model. Utility of the type curves was verified by re‐analysis of the Regina slug test previously analyzed by Kipp. These type curves indicate that near‐critical inertial effects result in early‐time delayed water‐level response followed by merger with, or more rapid recovery than, response for the fully damped case. Because of this early time response, slug tests in the moderately over‐damped range are best analyzed using log‐log type curves of (1 ? H/H₀) vs. Tt/. Failure to recognize inertial effects in slug test data could result in an over‐estimate of transmissivity, and a too‐small estimate of storage coefficient or too‐large estimate of well skin. However, application of the widely used but highly empirical Hvorslev (1951) method to analyze both the Regina slug test and type‐curve generated data indicate that such analyses provide T values within a factor of 2 of the true value.     

Photocatalytic Degradation of 17α‐Ethinylestradiol and Inactivation of Escherichia coli Using Ag‐Modified TiO2 Nanotube Arrays

Ag‐modified TiO₂ nanotube arrays (Ag/TiO₂ NAs) were prepared and employed as a photocatalyst for degradation of 17α‐ethinylestradiol (EE2) and inactivation of Escherichia coli. The as‐synthesized Ag/TiO₂ NAs were characterized by field‐emission scanning electron microscope (FESEM), X‐ray diffraction (XRD), and X‐ray photoelectron spectroscopy (XPS). It was found that metallic Ag nanoparticles were firmly deposited on the TiO₂ NAs with the pore diameter of 100 nm and the length of 550 nm. Photocatalytic degradation of EE2 and inactivation of E. coli were enhanced effectively in an analogical trend using Ag/TiO₂ NAs. In particular, Ag/TiO₂ NAs exhibited the antimicrobial activity even in the absence of light. The Ag acted as a disinfection agent as well as the dopant of the modified TiO₂ NAs photocatalysis by forming a Schottky barrier on the surface of TiO₂ NAs. Inorganic ions suppressed the rates of photocatalytic degradation of EE2, with HCO having a more pronounced effect than NO or SO. Humic acid (HA) was found to increase the rate of EE2 degradation.     

Adsorption of Complex Pollutants from Aqueous Solutions by Nanocomposite Materials

In view of water pollutants becoming more complex, both anionic and cationic pollutants need to be removed. The multi‐pollutants simultaneous removal is paid more and more attention. Hence, development composite materials for treatment complex wastewater are the aim of this study. In this research, iron–nickel nanoparticles deposited onto aluminum oxide (α‐Al₂O₃) and carbon nanotubes (CNTs) to form nanocomposite materials Fe–Ni/Al₂O₃ and Fe–Ni/CNTs, respectively, were used as adsorbents. The adsorption capacities of Fe–Ni/Al₂O₃ and Fe–Ni/CNTs for AO7, HSeO, and Pb²⁺ were observed to be 5.46, 8.28, 27.02, and 25.6 mg/g, 15.29 and 17.12 mg/g, separately. The composite materials with negative charges were superior in adsorption of anionic pollutants. Using orthogonal experimental design and analysis of variance to co‐treat dye AO7, HSeO and Pb²⁺ in aqueous solutions, seven testing factors were included: (1) adsorbent types, (2) amount of iron, (3) solution pHs, (4) AO7 concentrations, (5) Pb²⁺ concentrations, (6) HSeO concentrations and (7) reaction time. The experimental results showed that the removal of complex pollutants AO7, HSeO, and Pb²⁺ on Fe–Ni/CNTs could reach up to 90% in the optimal treatment conditions. When using Fe–Ni/CNTs as the adsorbent, the sorption isothermals were well fitted in the Freundlich isotherm, and R² could reach up to 0.98.     

Average sand particle trajectory examined by the Raindrop Detachment and Wind‐driven Transport (RD‐WDT) process

Recent studies of soil loss by the integrated action of raindrop impact and wind transport have demonstrated the significance of this mechanism. This paper presents data obtained during wind‐tunnel experiments examining the ‘Raindrop Detachment and Wind‐driven Transport’ (RD‐WDT) process to investigate average sand particle trajectory and the spatial extent at which the process operates. In the experimental design, at the same time as the horizontal wind velocities of 6·4, 10, and 12 m s^–1 passed through the tunnel, rainfall was simulated falling on very well sorted dune sand. The aspect and slope of the sand bed was varied to reproduce both windward (Ww) and leeward (Lw) slopes of 4º and 9º with respect to the prevailing wind direction. The average sand particle trajectories by the RD‐WDT process ( ) were estimated by a mass‐distribution function, which was integrated over a 7‐m uniform slope segment. The results showed that depended statistically upon the wind shear velocity (u*), and the effect of the slope gradient (θ) was insignificant on . This was different from that of the windless rain process ( ), ‘Raindrop Detachment and Splash‐driven Transport’ (RD‐ST), the spatial range of which relies strongly on θ. Additionally, was approximately 2·27 ± 2·2 times greater than the average path of a typical saltating sand particle of the rainless wind ( ), ‘Wind Erosion Saltation Transport’ (WE‐ST). Copyright © 2009 John Wiley & Sons, Ltd.     

Characterizing the degree of amplitude‐variation‐with‐offset nonlinearity in seismic physical modelling reflection data

The nonlinearity of the seismic amplitude‐variation‐with‐offset response is investigated with physical modelling data. Nonlinearity in amplitude‐variation‐with‐offset becomes important in the presence of large relative changes in acoustic and elastic medium properties. A procedure for pre‐processing physical modelling reflection data is enacted on the reflection from a water‐plexiglas boundary. The resulting picked and processed amplitudes are compared with the exact solutions of the plane‐wave Zoeppritz equations, as well as approximations that are first, second, and third order in , , and . In the low angle range of 0°–20°, the third‐order plane‐wave approximation is sufficient to capture the nonlinearity of the amplitude‐variation‐with‐offset response of a liquid‐solid boundary with , , and ρ contrasts of 1485–2745 m/s, 0–1380 m/s, and 1.00–1.19 gm/cc respectively, to an accuracy value of roughly 1%. This is in contrast to the linear Aki–Richards approximation, which is in error by as much as 25% in the same angle range. Even‐order nonlinear corrective terms are observed to be primarily involved in correcting the angle dependence of , whereas the odd‐order nonlinear terms are involved in determining the absolute amplitude‐variation‐with‐offset magnitudes.     

Diel patterns in coastal‐stream nitrate concentrations linked to evapotranspiration in the riparian zone of a low‐relief,agricultural catchment

Evapotranspiration (ET) can cause diel fluctuations in the elevation of the water table and the stage in adjacent streams. The diel fluctuations of water levels change head gradients throughout the day, causing specific discharge through near‐stream sediment to fluctuate at the same time scale. In a previous study, we showed that specific discharge controls the residence time of groundwater in streambed sediment that, in turn, exerted the primary control on removal from groundwater passing through the streambed. In this study, we examine the magnitude of diel specific discharge patterns through the streambed driven by ET in the riparian zone with a transient numerical saturated–unsaturated groundwater flow model. On the basis of a first‐order kinetic model for removal, we predicted diel fluctuations in stream concentrations. Model results indicated that ET drove a diel pattern in specific discharge through the streambed and riparian zone (the removal zones). Because specific discharge is inversely proportional to groundwater travel time through the removal zones and travel time determines the extent of removal, diel changes in ET can result in a diel pattern in concentration in the stream. The model predictions generally matched observations made during summertime base‐flow conditions in a small coastal plain stream in Virginia. A more complicated pattern was observed following a seasonal drawdown period, where source components to the stream changed during the receding limb of the hydrograph and resulted in diel fluctuations being superimposed over a multi‐day trend in concentrations. Copyright © 2013 John Wiley & Sons, Ltd.     

Factors controlling nitrogen release from two forested catchments with contrasting hydrochemical responses

Quantifying biogeochemical cycles of nitrogen (N) and the associated fluxes to surface waters remains challenging, given the need to deal with spatial and temporal variability and to characterize complex and heterogeneous landscapes. We focused our study on catchments S14 and S15 located in the Adirondack Mountains of New York, USA, which have similar topographic and hydrologic characteristics but contrasting stream nitrate ( ) concentrations. We characterized the mechanisms by which reaches the streams during hydrological events in these catchments, aiming to reconcile our field data with our conceptual model of factors that regulate nutrient exports from forested catchments. Combined hydrometric, chemical and isotopic (δ ) data showed that the relative contributions of both soil and ground water sources were similar between the two catchments. Temporal patterns of stream chemistry were markedly different between S14 and S15, however, because the water sources in the two catchments have different solute concentrations. During late summer/fall, the largest source of in S14 was till groundwater, whereas shallow soil was the largest source in S15. concentrations in surface water decreased in S14, whereas they increased in S15 because an increasing proportion of stream flow was derived from shallow soil sources. During snowmelt, the largest sources of were in the near‐surface soil in both catchments. Concentrations of increased as stream discharge increased and usually peaked before peak discharge, when shallow soil water sources made the largest contribution to stream discharge. The timing of peaks in stream concentrations was affected by antecedent moisture conditions. By elucidating the factors that affect sources and transport of N, including differences in the soil nutrient cycling and hydrological characteristics of S14 and S15, this study contributes to the overall conceptualization of release from temperate forested catchments. Copyright © 2007 John Wiley & Sons, Ltd.     

Stream response to precipitation variability: a spectral view based on analysis and modelling of hydrological cycle components

Hydrological processes commonly exhibit long‐term persistence, also known as the ‘Hurst phenomenon’. Here, we examine long‐term precipitation and streamflow time series from the Elbe River Basin to quantify differences in the spectral properties and in the Hurst parameter estimates () of the individual hydrological cycle components. Precipitation‐runoff modelling is performed for the Elbe River sub‐catchment Striegis using the Soil and Water Assessment Tool (SWAT). For 38 daily 50 years long streamflow time series from the Elbe River Basin, baseflow separation and spectral analysis is performed. The results show a spectral shift towards low‐frequency scales (>2 years) from precipitation to baseflow, with a parallel increase of from 0.52 (precipitation) to 0.65 (baseflow). The SWAT model is able to reproduce both, the main low‐frequency mode (≈7 yr.) and the (0.62) of the observed Striegis River flow time series. The baseflow appears to be the main component which shapes the low‐frequency response and of streamflow in the Elbe River Basin to the input precipitation. This conclusion is further confirmed through PMWIN‐MODFLOW groundwater modelling of a hypothetic phreatic stream‐connected aquifer system that consists of various soils (sand, loamy sand and silt). A power shift towards lower frequencies and an increase of for the hydraulic heads is obtained, as the aquifer's lateral dimensions increase and its hydraulic conductivity decreases. The average of the groundwater heads is 0.80, 0.90 and 1.0 for sand, loamy sand and silt aquifers, respectively. Copyright © 2014 John Wiley & Sons, Ltd.     

Geochemical characterization of the organic matter, pore water constituents and shallow methane gas in the eastern part of the Ulleung Basin, East Sea (Japan Sea)

Abstract Geochemical analyses of sediments, pore water and headspace gas of the piston cores taken from the eastern part of Ulleung Basin of the East Sea (Japan Sea) were carried out to assess the origin of the sedimentary organic matter and interstitial fluid. Several tephra layers within the core are identified as the Ulleung‐Oki (10.1 ka), the Aira‐Tanzawa (23 ka) and the Ulleung‐Yamato (30.9 ka) tephras. With the exception of these volcanic layers, the cores consist predominantly of muddy sediments that contain >0.5% total organic carbon. Atomic C/N ratios and δ¹³C_org values suggest that the organic matter originated from marine algae rather than from land vascular plants, whereas Rock‐Eval pyrolysis suggests that the organic matter is thermally immature and comes from a land vascular plant (Type III). These conflicting results seem to be caused by the heavy oxidization of the marine organic matter. Sulphate concentration profiles of pore waters show strongly linear depletion (r² > 0.97) with sediment depth. The estimated sulphate–methane interface (SMI) depth using the sulphate concentration gradient was nearly 3.5 m below seafloor (mbsf) in the southern part of the study area, and deeper than 6 mbsf in the northern part of the area. The difference in SMI depths is likely associated with the amount of the methane flux. The methane concentration below the SMI in the two southern cores increases rapidly, implying the occurrence of methanogenesis and anaerobic methane oxidation (AMO). In contrast, the two northern cores have a low methane concentration below the SMI. values measured from all cores were in the range of −83.5 to −69.5‰, which suggests that the methane derives from a methanogenic microbe. values become decreased toward SMI, but increased below SMI; therefore, has eventually the minimum value near the SMI. The values are also decreased when the methane concentration is increased. These phenomena support the typical occurrence of AMO in the study area.     

Spatial and temporal variations in rainfall characteristics in mountainous and lowland areas in Taiwan

Although changes in rainfall characteristics have been noted across the world, few studies have reported those in mountainous areas. This study was undertaken to clarify spatial and temporal variations in rainfall characteristics such as annual rainfall amount (Pr), mean daily rainfall intensity (η), and ratio of rain days (λ) in mountainous and lowland areas in Taiwan. To this aim, we examined spatial and year‐to‐year variations and marginal long‐term trends in Pr, η, and λ, based on rainfall data from 120 stations during the period 1978–2008. The period mean rainfall () at the lowland stations had strong relationships with the period mean daily rainfall intensity () and the period mean ratio of rain days () during those 31 years. Meanwhile, was only strongly related to at mountainous stations, indicating that influences on spatial variations in were different between lowland and mountainous stations. Year‐to‐year variations in Pr at each station were primarily determined from the variation in η at most stations for both lowland and mountainous stations. Long‐term trend analysis showed that Pr and η increased significantly at 10% and 31% of the total 120 stations, respectively, and λ decreased significantly at 6% of the total. The increases in Pr were mostly accompanied by increases in η. Although stations with significant η increases were slightly biased toward the western lowland area, increases or decreases in Pr and λ were not common. These results contribute to understanding the impacts of possible climate changes on terrestrial hydrological cycles. Copyright © 2012 John Wiley & Sons, Ltd.     

Magnesium Ammonium Phosphate Production from Wastewater through Box–Behnken Design and Its Effect on Nutrient Element Uptake in Plants

This study examined ${\rm NH}_{{\rm 4}}^{{\rm + }} $ , ${\rm PO}_{{\rm 4}}^{{\rm 3}- } $ recovery and the concentration of residual ions from anaerobic effluent of the potato processing industry through magnesium ammonium phosphate (MAP) precipitation using a Box–Behnken design. The regression model was statistically significant in terms of ${\rm NH}_{{\rm 4}}^{{\rm + }} $ and ${\rm PO}_{{\rm 4}}^{{\rm 3}- } $ removal efficiency and residual ion concentrations. Optimum ${\rm NH}_{{\rm 4}}^{{\rm + }} $ and ${\rm PO}_{{\rm 4}}^{{\rm 3}- } $ removal was obtained at pH 9.50 and at Mg²⁺/${\rm NH}_{{\rm 4}}^{{\rm + }} $ /${\rm PO}_{{\rm 4}}^{{\rm 3}- } $ molar ratio of 1.8:1:1.8. Under these conditions, Mg, Ca, K, Fe, and Cl concentrations required for plant growth significantly decreased with MAP precipitation, which was supported by EDX analysis of dry MAP precipitate. The fertilizer effect of MAP on the growth of corn and tomato plants was compared with chemical fertilizers through pot trials. Nutrient element uptake levels of plants were examined in different fertilizer sources. While Mg, Fe, Cu, Mn, and Zn nutrient element uptake levels were sufficient in MAP pots, Ca uptake exceeded sufficient level. Average levels of N, P, K, Mg, Cu, and Mn of corn plant were higher in MAP than other pots. The average N, P, and Mg levels of tomato plant in MAP pots were higher than other pots. N/K ratio, which is important in tomato plants, was better optimized in MAP pots. Only Ni, Cr, and Pb heavy metals were found in plants.     

Time‐lapse pre‐stack seismic data registration and inversion for CO2 sequestration study at Cranfield

Pre‐stack seismic data are indicative of subsurface elastic properties within the amplitude versus offset characteristic and can be used to detect elastic rock property changes caused by injection. We perform time‐lapse pre‐stack 3‐D seismic data analysis for monitoring sequestration at Cranfield. The time‐lapse amplitude differences of Cranfield datasets are found entangled with time‐shifts. To disentangle these two characters, we apply a local‐correlation‐based warping method to register the time‐lapse pre‐stack datasets, which can effectively separate the time‐shift from the time‐lapse seismic amplitude difference without changing the original amplitudes. We demonstrate the effectiveness of our registration method by evaluating the inverted elastic properties. These inverted time‐lapse elastic properties can be reliably used for monitoring plumes.     

Mobility Enhancement of Mn Oxide during Permanganate Oxidation of TCE

Manganese (Mn) oxide precipitation during in situ permanganate oxidation of organic compounds can cause pore clogging, reduce permeability, and increase resistance to mass transfer. Stability of Mn oxide is required to enhance oxidation effectiveness. Batch tests were conducted at eight polyphosphate (PP) to permanganate () mass ratios (0 to 8) at three MnO₄⁻¹ concentrations (500, 1000, or 2000 mg/L) for identifying mass ratios to maximize stability of Mn oxide produced in the presence of trichloroethylene (TCE). In general, stability of Mn oxide was the maximum at mass ratio of approximately 4. Three column tests were designed to investigate the impact of PP on overall removal of 4.6 or 7.0 g TCE emplaced as nonaqueous phase liquid within the column porous media. Water flush, chemical flush using alone (1000 mg/L), and chemical flush using (1000 mg/L) and PP (4000 mg/L) were conducted. Mass removal of TCE and changes in media permeability were estimated over a period of 78 to 312 h (12 to 49 pore volumes [PVs]). Column tests demonstrated enhanced removal (~90%) of TCE during chemical flush with and PP in 12 PVs as compared with approximately 64% during -only flush and approximately 26% during water flush. Pressure drop changes across the column captured change in media permeability and revealed that water flush and PP and flush caused significantly lower flow resistance as compared with -only flush. These results indicate that PP was capable of mobilizing Mn oxide away from the reaction zones, thereby reducing pore clogging and enabling better and long-term contact between TCE and the aqueous phase.     

Evaluating equilibrium and non‐equilibrium transport of ammonium in a loam soil column

Release of nitrogen compounds into groundwater, particularly those compounds from excessive agricultural fertilization, is a major concern in an aquifer recharge. Among the nitrogen compounds, ammonium ( ) is a common one. In order to assess the risk of agricultural fertilizer contamination to an aquifer through infiltration, adsorption onto a loamy agricultural soil profile (0–0.60 m depth) was studied using a soil column experiment and modelling simulation. The soil used in the experiment was drawn from an agricultural field in Xinzhen, Fangshan district, Beijing, China, and reconstituted in laboratory soil columns. Column experiments were conducted using bromide (conservative tracer) and ‐bearing aqueous solutions. The ammonium concentrations in the soil water samples were measured, and their values were plotted as the breakthrough curves. The chemical's soil–water distribution coefficients (K_d) were calculated using breakthrough curves. Then the retardation factor (R) in saturated soil was calculated. For the ‐bearing aqueous solutions, the strongest adsorption occurred at the soil depth of 0.30–0.45 m. The convection–dispersion equation model and chemical non‐equilibrium model in Hydrus‐1D were used to simulate transport in the loamy soil. The two‐site chemical non‐equilibrium model in Hydrus‐1D was best to simulate transport through the soil column. Parameter sensitivity study was conducted to investigate the influences of solute transport by K_d, the fraction of exchange sites assuming to be in equilibrium with the solution phase (f), the longitudinal dispersivity (λ), and the first‐order rate coefficients (ω). The sensitivity analysis results indicate K_d is the most critical parameter.     

Effects of variations in fluid properties and fracture geometry on dispersion,anisotropy, and reflection in media with planar fractures

Our objective was to discover the effect of variations in fluid properties and fracture geometry on the velocity of seismic wave propagation in fluid‐saturated media with parallel planar fractures. We used numerical models calculated by analytical solutions to examine the behaviour of P‐wave phase velocity dispersion in the normal direction to layering, in non‐porous and porous media with planar fractures. We also examined the anisotropy of low frequency phase and group velocities of fast and slow P‐waves and angular‐dependent reflection coefficients in media with planar fractures, under conditions of saturation by fluids with varying bulk moduli, densities, and fracture apertures. We defined several parametre , , and characterising dispersion, characterising anisotropy, characterising the difference between fast and slow modes, and R₀ and characterising reflection. Our results show that the behaviour of dispersion shows wider stopbands in the case of gas saturation. Concavity indicator of dispersion for gas saturation was greater than that for liquid saturation and is usually greater than one. Anisotropy is more sensitive to bulk modulus contrast than to density contrast between the solid and the fluid, and is more sensitive to density contrast than to bulk modulus contrast. The case of gas saturation usually had a greater negative R₀ and a greater value of compared with those of brine and heavy and light oil saturations. Our results are helpful in distinguishing fluid types saturating geophysical fractures and estimating the aperture and spacing of planar fractures. In seismic exploration, bulk modulus and fluid density can provide useful information in distinguishing among brine, oil, and gas; fracture geometry is important to estimate the permeability of reservoirs.     

Closed Analytic Elements with Flexible Geometry

A simple and fast treatment of hydrogeologic features with irregularly shaped boundaries in two‐dimensional analytic element groundwater flow models is presented. The star domain shapes of the features are restricted to closed shapes represented as smooth and continuous single‐valued functions of distance from a focus point, . The element can be used to treat a variety of boundary and continuity conditions, including those of irregularly shaped lakes or heterogeneities in hydraulic conductivity. The new element is demonstrated via some simple illustrative test cases and shown to be efficient, accurate, and much simpler to implement than existing solutions for irregular shapes.     

High‐resolution and super stacking of time‐reversal mirrors in locating seismic sources

Time reversal mirrors can be used to backpropagate and refocus incident wavefields to their actual source location, with the subsequent benefits of imaging with high‐resolution and super‐stacking properties. These benefits of time reversal mirrors have been previously verified with computer simulations and laboratory experiments but not with exploration‐scale seismic data. We now demonstrate the high‐resolution and the super‐stacking properties in locating seismic sources with field seismic data that include multiple scattering. Tests on both synthetic data and field data show that a time reversal mirror has the potential to exceed the Rayleigh resolution limit by factors of 4 or more. Results also show that a time reversal mirror has a significant resilience to strong Gaussian noise and that accurate imaging of source locations from passive seismic data can be accomplished with traces having signal‐to‐noise ratios as low as 0.001. Synthetic tests also demonstrate that time reversal mirrors can sometimes enhance the signal by a factor proportional to the square root of the product of the number of traces, denoted as N and the number of events in the traces. This enhancement property is denoted as super‐stacking and greatly exceeds the classical signal‐to‐noise enhancement factor of . High‐resolution and super‐stacking are properties also enjoyed by seismic interferometry and reverse‐time migration with the exact velocity model.