岩体基本参数对岩质边坡变形的影响

文章利用有限差分程序FLAC,定量化讨论了边坡岩体(软岩)的变形模量、泊松比、密度、粘聚力、内摩擦角、边坡高度等参数对软岩边坡变形的影响。研究表明,边坡位移随变形模量E的增大而减小;泊松比μ的增加,则会引起x方向的位移的增加,y方向的位移减小;而岩体密度对岩石边坡位移的影响甚弱。边坡岩体的粘聚力c对边坡变形的影响程度与岩体的其他参数间存在很大关系。内摩擦角对边坡位移的影响大小,则取决于粘聚力c的取值。此外,随着边坡高度的增加边坡变形则会随之增加。其中x方向位移变化对边坡高度的变化更为敏感;同样,在边坡岩体其他参数不变的情况下,边坡倾角越大,边坡变形也越大。     

Estimation of the rock mass deformation modulus using a rock classification system

It is often difficult to directly obtain specific design parameters of interest. In these situations, estimation based on empirical correlations is an alternative. The deformation modulus of a rock mass, which is important to know for engineering projects, is measured by in situ tests, such as plate bearing, flat jack, pressure chamber, borehole jacking and dilatometer tests. Nevertheless, these in situ tests are expensive, time consuming and sometimes even impossible. Many attempts have been made to estimate the E modulus using easy-to-obtain parameters of a rock mass. This paper reviews previous studies and the equations that have been developed. In addition, this study presents a new relation developed using a database of 82 dilatometer test results gathered from two dam sites and a tunnel site. Statistical analyses were performed to correlate accessible rock parameters with measured E modulus values from in situ tests. Knowing that discontinuity characteristics and the strength of rock materials are the most important contributors to rock deformability, the focus was on identifying parameters that are affected by the mentioned properties. Among the tested parameters, RMR (Rock Mass Rating) showed the best correlation with the E modulus. Statistical analyses resulted in a new empirical equation that has an acceptable estimation ability.     

A nonlinear deformation modulus based on rock mass classification

Summary This paper describes the development of an empirical nonlinear stress dependent expression for the deformation modulus of rock masses based on rock mass classification. The expression defines the deformation modulus as the ratio of the deviator stress at failure to the major principal strain at failure. The Hoek and Brown failure criterion is used to predict the deviator stress at failure. Research was directed toward developing a failure criterion defining the major principal strain at failure. The expression for the deformation modulus was extended to rock mass conditions through correlations with observed deformations from case history studies and predicted deformations from finite element analyses.     

随机分布贯穿裂隙岩体变形特性研究

洞室开挖后,其周边通常会产生许多随机分布的贯穿裂隙,直接影响洞室围岩稳定,研究随机分布贯穿裂隙岩体的变形及变形特性具有重要意义。基于线弹性理论和线性刚度理论计算岩石和裂隙的位移,用概率的方法建立了随机分布贯穿裂隙岩体变形的计算模型,给出了随机分布贯穿裂隙岩体的等效弹性模量和等效泊松比,研究了岩石和裂隙的材料参数和几何参数对岩体等效弹性模量和等效泊松比的影响。可得如下结论：等效弹性模量和等效泊松比随着岩石弹性模量的增大而增大;等效泊松比随着岩石泊松比的增大而增大;等效弹性模量和等效泊松比随着裂隙法向刚度的增大而增大;随着剪切刚度的增大,等效弹性模量逐渐增大,而等效泊松比则逐渐减少;随着裂隙平均间距的增大,等效弹性模量逐渐减小,等效泊松比在平均倾斜角较小时逐渐增大,在平均倾斜角较大时逐渐减小;随着裂隙平均倾斜角的增大,等效弹性模量先减小后增大,而等效泊松比先增大后减小。模型能较全面地考虑构成岩体的岩石和裂隙的材料参数与几何参数对岩体变形的影响,其结果对研究洞室围岩的变形和工程设计有一定的参考价值。     

岩体结构控制下的斜坡变形特征

为了分析岩体结构与斜坡变形的作用关系,以巴东城区为例,探讨了区内主要地层（三叠系巴东组第2段T2b2、第3段T2b3）岩体结构在内、外动力地质作用下的演化过程,进而分析了不同类型岩体结构控制下的表层斜坡的变形特征。结果表明：内动力地质作用过程中形成了岩体结构,而外动力地质作用改造着岩体结构;根据沉积成岩、构造作用过程中所形成层理、节理、劈理的发育程度,可将岩体划分为层状结构、块裂结构和碎裂结构;风化、水等外动力地质作用对岩体结构的改造结果受控于原岩结构;巴东组第3段层状岩体多沿层间软弱夹层顺层滑动;巴东组第2段互层状岩体,层间差异崩解作用易形成崩塌;结构面的组合关系、发育规模控制着块体失稳的形式和规模;密集发育的劈理将岩体分割呈碎裂状结构,卸荷松动下呈膝状弯曲。这些认识对巴东地区斜坡灾害分析、防治具有一定的指导意义。     

节理岩体锚杆的综合变形分析

在总结国内外对节理岩体中锚杆加固机制的试验研究和理论探讨基础上,综合考虑锚杆的切向和轴向变形能力,建立节理锚固锚杆在剪切荷载作用下的变形模型,将节理锚固锚杆的变形区划分为弹性变形段和挤压破坏段,引入表征挤压破坏段长度的变量,对锚杆与岩体的相互作用机制进行理论分析,推导了剪切荷载与剪切位移和轴向荷载与轴向位移的关系。通过分析锚杆的屈服破坏形式,得到了确定挤压破坏段长度的方法。最后,通过算例分析了挤压破坏段长度与锚杆直径、岩体强度、锚固角度等参数的关系,得到了以下结论：（1）节理锚固锚杆抗剪作用的实质是锚杆调动岩体的抗压强度抵抗节理切向荷载。在抗压强度较高的硬岩中,挤压破坏段局限于节理面附近,锚杆影响范围小;而在抗压强度较低的软岩中,挤压破坏段较大,而且会产生较大的剪切变形,锚杆影响范围较大。（2）锚杆屈服破坏形式与岩质和锚杆直径有关。硬质岩体发生剪切屈服,而较软岩体中容易发生弯曲屈服;小直径锚杆一般直接剪切屈服,而大直径锚杆可能发生弯曲屈服。锚杆屈服破坏后出现塑性铰,挤压破坏段范围在节理一侧约为直径的1～2倍,继续增加剪切荷载,挤压破坏段长度不再增大。（3）随岩质的不同,锚杆锚固节理的最优锚固角变化较大。岩质较硬时,最优锚固角度较小,反之则较大。     

非贯通类节理岩体剪切变形规律分析

通过直剪条件下的模型试验研究具有相同连通率、含不同起伏角的共面闭合节理在不同法向应力作用下的剪切变形特征。试验结果表明：在达到峰值剪切强度前,剪切应力-位移曲线具有明显的线性段与非线性段;岩桥在法向与剪切荷载的共同作用下会产生一定程度的弱化,积累到一定程度时宏观表现为剪切应力软化。详细阐述了试验过程中裂纹发展的4个阶段并描述了剪切应力-剪切变形曲线变化的特征,提出一个能反映剪切应力-剪切变形曲线全过程的经验本构模型。新模型采用分段函数描述曲线变化特征。直剪试验数据分析表明,该模型能够拟合剪切应力-剪切变形变化发展趋势且具有较高的拟合精度,验证了模型的正确性。最后,对其存在的不足亦进行了简要分析     

预应力锚索加固岩质边坡的设计实例

在修筑高等级公路时 ,常需要开挖而形成高陡路堑边坡 ,边坡稳定与否将影响公路施工和运营的安全。 对具有潜在滑动面的不稳定岩质边坡 ,通常采用预应力锚索和锚杆加固以节约工程投资与缩短施工时间。结合某高速公路路堑岩质边坡工程 ,在分析边坡工程地质条件的基础上 ,提出了预应力锚索加固边坡的设计方法和步骤 ,为相关边坡工程的加固提供借鉴经验。     

Innovative constant resistance large deformation bolt for rock support in high stressed rock mass

Bolt supporting is a major technology used in highly stressed surrounding rock support. Although significant developments of new patterns of bolts have been documented, the stiffness problem which causes the bolt to cannot adapt to the large deformation of surrounding rock was still unsolved. Hence, a novel bolt with constant working resistance and steady large deformation was developed to bear creep deformation and impact load. The constant resistance large deformation bolt (CRLD bolt) was composed of constant resistance element, bolt rod, baffle plate, and tightening nut, which would efficiently control the engineering disasters such as collapse and rock blast. The results of static tensile tests indicated that the CRLD bolt could provide constant resistance ranging from 120 to 130 kN, and the maximal elongation length was 1100 mm without bolt breaking at tensile rate of 10, 20, and 100 mm/s, respectively. Tensile rate has no obvious relationship with constant resistance force. Dynamical impact tests showed that bolt resistance property and its absorption capacity of impact energy were stable, and the dynamic constant resistance changed from 90 to 120 kN, with the impacting height for drop hammers of 10 and 1000 mm. It has also been proved that this kind of bolt has good performance in practical application such as in Qing Shui coal mine. The in situ monitoring results indicate that the CRLD bolt is able to retain rock mass stability and prevent the surrounding rocks from being destructed due to its large-scale deformation. Overall, CRLD bolt is suitable for large deformation, constant resistance, and energy absorption.     

层状岩体巷道弯曲变形的有限元模拟

在缓倾斜或水平层状岩体中开挖巷道时巷道顶底板弯曲变形和破坏的问题十分突出,巷道往往因这些部位发生过大变形而率先破坏,导致结构的整体失稳。根据层状岩体的特点,分析了其弯曲变形破坏的机理和条件,利用考虑偶应力的Cosserat介质理论,基于Matlab平台编制了相应的计算程序,对水平层状岩体巷道的变形特征及影响因素进行了模拟研究,结果表明Cosserat理论对层状岩体巷道的开挖模拟是适用的,而且简便。     

Effect of tunnel depth on modulus of deformation of rock mass

Summary Deformability of rock mass significantly influences its behaviour and is, therefore, an important consideration for the design of underground openings. The modulus of deformation of rock mass is, however, normally obtained from expensive and time-consuming uniaxial jacking tests, whose results often have a large scatter. An empirical correlation has, therefore, been proposed for a quick and inexpensive preliminary estimation of the modulus of deformation of rock mass on the basis of field instrumentation carried out in tunnels in India.     

VJC-RMR法在岩体变形模量确定中的应用

在介绍VJC-RMR法 ( Volumetric joint count-rock mechanics rating method )基本原理的基础上,对贵阳市鱼简河水库坝基岩体进行了质量评价和变形模量确定,并与原位试验法、Q法 (Rock mass quality) 和岩体损伤的分形模型(Fractional model of rock mass damage)进行了比较。结果表明,VJC-RMR法能够将一维问题转化为三维问题,更好地反映岩体的实际情况,是进行岩体质量评价和参数确定较好的一种方法。     

Demonstration of spatial anisotropic deformation properties for jointed rock mass by an analytical deformation tensor

This paper develops a joint deformation tensor (JD), which considers all of the joint's mechanical and geometrical parameters that affect the deformability of the rock mass. The method based on JD (JD method) and an elastic deformation anisotropy index (EDAI) are deduced for estimating the spatial anisotropy deformation of a jointed rock mass. The numerical modeling and in situ true triaxial compressive experiments well verified the effectiveness of the EDAI and JD method for the rock mass containing one joint set, orthogonal joint sets or the rock mass containing any types of joint network with unity stiffness ratio.     

Coupling of diffusional mass transport and deformation in a tight rock

Simple governing equations coupling diffusional transport at a macroscopic scale and deformation in a tight rock are formulated. The deformation alone is described by a linear viscous rheology. Several deformations of geological interest are analyzed, including the folding of an embedded layer. A basic feature is the length-scale dependence of diffusional effects. Interpretation of natural structures permits the estimation of parameters governing the diffusional transport and rate of deformation.     

考虑累积损伤效应的围岩变形特性研究

隧道爆破开挖诱发的动力扰动作用范围往往远大于其开挖进尺,同一部位围岩受到循环爆破开挖的多次扰动普遍存在累积损伤。对乌东德水电站左岸导流洞爆破开挖过程中的爆破振动和围岩变形监测进行了监测和数值分析,基于累积损伤理论,通过引入损伤判据及损伤变量,考虑计算中产生的不同程度的损伤区域的岩体参数劣化,并将劣化后的参数引入相应损伤单元进行后续开挖爆破数值模拟计算,从而对岩体爆破开挖累积损伤效应进行模拟。通过比较乌东德水电站导流洞的实测数据以及数值模拟计算结果发现,考虑累积损伤的计算结果无论是爆破振动速度还是围岩变形均更接近于实测值。对爆破开挖的分析模拟中应考虑围岩的多次循环爆破累积损伤效应。     

Analytical model for the design of grouted rock bolts

An analytical model which represents the behaviour of a reinforced rock mass near a circular underground opening in a homogeneous, uniform stress field has been developed. The theory adopts the concepts of elastoplasticity and considers a proper interaction mechanism between the ground and the grouted (or friction) bolts. It highlights the influence of the bolt pattern on the extent of the yield zone and tunnel deformation. A dimensionless parameter is introduced as a design tool which relates the tunnel convergence to the bolt spacing for a given bolt length. This publication contains the derivation of the analytical model and an illustration of the effect of bolts on the stress and displacement field near an opening. Its application to tunnel design is discussed briefly. The verification of the theory by laboratory simulation and field measurements will be presented, in detail, in a future publication.     

运用ANSYS分析开采倾斜煤层引起的地表变形

针对倾斜煤层的开采特点,应用有限元基本原理,建立了倾斜煤层开采的有限元分析模型。利用大型有限元分析软件ANSYS对开采倾斜煤层引起的岩体移动、地表沉陷及应力分布情况进行了数值模拟,总结出倾斜煤层开采时岩体移动的基本特征及地表沉陷的相关参数。利用ANSYS软件作出地表基准点的水平、下沉移动分布曲线、应力分布曲线以及计算模型的应力等值线图、水平移动等值线图和下沉等值线图。上述分布图直观地显示了顶板、煤层及底板的变形以及应力分布情况。阐明了倾斜煤层开采引起地表沉陷的变形机理。为矿区建筑物下倾斜煤层的开采提供了参考依据。     

考虑岩体扩容和塑性软化的软岩巷道变形解析

考虑岩体的扩容和塑性软化特性,引进扩容梯度和软化模量的概念,推导出均匀介质中软岩巷道应力和变形的理论解答。与其他理论模型进行比较,验证了理论模型的正确性。通过算例分析了岩体的扩容梯度和软化模量对围岩塑性区、破裂区半径以及围岩变形和压力的影响。分析结果表明,考虑岩体的扩容和塑性软化特性使得分析更加准确,研究成果对软岩巷道支护设计与施工具有一定指导意义。     

鱼简河水库坝基岩体模量研究

岩体变形模量的确定是岩石力学界研究的难点问题。贵州省鱼简河水利工程是国家重点工程,该工程大坝坝型为拱坝,坝基岩体变形模量的大小直接影响其坝体结构设计。本文在坝基岩体分组的基础上,利用Monte-Carlo模拟技术,采用RMR法与岩体损伤的分形模型对岩体变形模量进行估算,最后结合原位试验和工程地质类比给出岩体参数建议值,为坝体设计提供合理的计算参数。     

多节理岩体裂纹扩展及变形破坏试验研究

为了研究不同倾角下多节理岩体力学行为,采用10 MN微机控制电液伺服大型多功能动静力三轴仪,开展包含较多预制非贯通节理类岩石试件的单轴压缩试验,研究了多节理岩体裂纹的特征、贯通模式、破坏模式、应力-应变特征等与节理倾角之间的关系。试验结果表明,（1）多节理岩体的裂纹类型主要有翼裂纹和次生共面裂纹,翼裂纹的扩展路径与单个节理情况下的扩展路径差异较大,翼裂纹起裂后沿起裂方向存在较长的扩展长度,直接与相邻节理或翼裂纹形成贯通,并且裂纹的贯通表现出四种不同的模式;（2）多节理岩体的破坏模式归纳为3种类型：平面破坏、块体转动式破坏和台阶式破坏;（3）根据多节理岩体的应力-应变曲线在应变软化阶段所表现出的不同非线性变形行为特征,可以将曲线归纳为4种类型;（4）多节理岩体的强度和变形各向异性特征非常显著,强度和弹性模量均在节理倾角30°时最小,90°时最大。