Copper Speciation in a Collection of Geochemical Reference Materials Using Sequential Extraction and Evaluation of the Validity Using XANES Spectroscopy

Copper speciation in a collection of Japanese geochemical reference materials (JSO‐1, JLk‐1, JSd‐1, ‐2, ‐3 and ‐4, JMs‐1 and JMs‐2) was achieved by sequential extraction and characterised using X‐ray absorption near‐edge structure spectroscopy. In the first step of the extraction, referred to as the acid fraction, between 1% and 20% total Cu within the reference materials was extracted. Such a result is typically accounted for by absorption of Cu onto clay minerals. However, the presence of Cu sulfate (an oxidation product of chalcopyrite) was observed in some of the stream sediments affected by mining activity (JSd‐2 and JSd‐3) instead. Copper was extracted in the reducible fraction (targeting Fe hydroxide and Mn oxide) (2–49% total Cu). Between 2% and 51% Cu was extracted in the oxidised fraction (targeting sulfides and organic matter). X‐ray absorption near‐edge structure spectroscopy clarified that the reducible fraction consisted of Cu bound to Fe hydroxide, whereas the oxidised fraction was a mixture of Cu bound to humic acid (HA) and Cu sulfide. In the oxidisable fraction, chalcopyrite was the predominant species identified in JSd‐2, and Cu bound to HA was the major species identified in JSO‐1 (a soil sample).     

Comparison of Two Sample Preparation Methods for X‐Ray Fluorescence Spectrometry in the Determination of Ni and Cr

Pressed powder pellets and fused beads or glass disks are routinely used in X‐ray fluorescence spectrometry for the determination of major and trace elements, respectively, in geological materials. In order to evaluate the performance of these two sample preparation methods, we determined Ni and Cr concentrations of fourteen RMs from Japan, France and South Africa, and eighty‐five igneous and three sedimentary rock samples from Mexico in both powder pellets and glass beads. We also computed new values of statistical parameters for RMs from an outlier‐based multiple‐test method and compared them with the literature mean and confidence limit values. The results showed that the multiple‐test method provided more reliable central tendency and dispersion parameters for RMs than those obtained previously from the two or three standard deviation method, or from robust methods. The powder pellet and fused bead sample preparation methods provided consistent results for Ni and Cr at concentration levels > 50 μg g^?1 in this application; for lower concentration levels, however, these methods showed somewhat greater differences. For quantitative comparisons, both ordinary and weighted least‐squares linear regression models were used to show that the two sample preparation methods provided generally unbiased results.     

A Practical Method for Accurate Measurement of Trace Level Fluorine in Mg‐ and Fe‐Bearing Minerals and Glasses Using Electron Probe Microanalysis

Fluorine plays an important role in magmatic and hydrothermal processes, but due to its low abundance in geological samples determining F is difficult by electron probe microanalysis. By using a W‐Si multi‐layered pseudocrystal as the diffraction crystal instead of thallium acid phthalate (TAP), count rates were considerably higher, which however introduced spectral interferences between FKα and FeLα and MgKβ lines when normal integral mode is applied. In this study, we developed a protocol using a W‐Si multi‐layered pseudocrystal for measuring accurately trace level F in both minerals and glasses. First, we used differential mode with an optimised PHA (pulse height analysis) setting in signal processing, instead of normal integral mode, which completely eliminated the second‐order MgKβ line. Second, the overlap of the first‐order FeLα on FKα peak, which cannot be filtered by modifying the PHA setting, was calibrated quantitatively using F‐free minerals and silicate glasses. Applying this two‐step method, F was determined in a number of reference glasses, as well as in glasses synthesised from powders of the rock reference materials AC‐E, GS‐N and DR‐N. Our data are consistent within error with F concentrations determined by other methods, demonstrating the reliability of this method.     

Chemical Analysis of Iron Meteorites Using a Hand‐Held X‐Ray Fluorescence Spectrometer

We evaluate the performance of a hand‐held XRF (HHXRF) spectrometer for the bulk analysis of iron meteorites. Analytical precision and accuracy were tested on metal alloy certified reference materials and iron meteorites of known chemical composition. With minimal sample preparation (i.e., flat or roughly polished surfaces) HHXRF allowed the precise and accurate determination of most elements heavier than Mg, with concentrations > 0.01% m/m in metal alloy CRMs, and of major elements Fe and Ni and minor elements Co, P and S (generally ranging from 0.1 to 1% m/m) in iron meteorites. In addition, multiple HHXRF spot analyses could be used to determine the bulk chemical composition of iron meteorites, which are often characterised by sulfide and phosphide accessory minerals. In particular, it was possible to estimate the P and S bulk contents, which are of critical importance for the petrogenesis and evolution of Fe‐Ni‐rich liquids and iron meteorites. This study thus validates HHXRF as a valuable tool for use in meteoritics, allowing the rapid, non‐destructive (a) identification of the extraterrestrial origin of metallic objects (i.e., archaeological artefacts); (b) preliminary chemical classification of iron meteorites; (c) identification of mislabelled/unlabelled specimens in museums and private collections and (d) bulk analysis of iron meteorites.     

Speciation Study of Cr in a Geochemical Reference Material Sediment Series Using Sequential Extraction and XANES Spectroscopy

Speciation of Cr in geochemical reference materials was characterised by sequential extraction and X‐ray absorption near‐edge structure (XANES) spectroscopy to identify Cr(III) resulting from the reduction of pollutant Cr(VI). Sequential extraction suggested that the amount of Cr associated with an acetic acid soluble fraction was low; Cr associated with a reducible phase and an oxidisable phase was extracted at 5–10% of the total Cr concentration, and the residual phase was found to be the dominant Cr‐containing fraction. Cr speciation in soil artificially doped with Cr(VI) and sediment samples collected from highly populated and industrialised areas was different from that in naturally occurring materials. Substantial Cr was extracted as a reducible phase (15–30%) and an oxidisable phase (30–60%) for these samples. Through subsequent XANES spectroscopy analysis, the reducible phase was explained by Cr bound to Fe hydroxide, while the oxidisable phase was a mixture of Cr bound to humic substances and Cr hydroxides. That is, Cr(VI) present as a contaminant in sediments and soils was reduced to Cr(III), which then bound to Fe hydroxide and humic substances, precipitating as a hydroxide. Thus, a combination of sequential extraction and XANES spectroscopy allows for effective identification and quantification of the chemical forms of Cr in sediments and soils.     

Forty‐Nine Major and Trace Element Concentrations Measured in Soil Reference Materials NIST SRM 2586, 2587, 2709a, 2710a and 2711a Using ICP‐MS and Wavelength Dispersive‐XRF

Excellent agreement was noted in the concentration of major and trace elements in five NIST (National Institute for Science and Technology) soil reference materials (NIST SRM 2586, 2587, 2709a, 2710a and 2711a) between measurement results from wavelength dispersive‐XRF and ICP‐MS from two independent laboratories, and NIST certificate of analysis and literature data. We describe the variability in concentrations of up to forty‐nine elements (plus loss on ignition) and provide values for up to twenty‐one elements previously uncharacterised by NIST in these soil RMs. The additional characterisation provided in this investigation can be utilised to reduce the measurement bias of custom calibration routines and improve the quality of control checks developed using these NIST RMs.