随机波浪下斯托克司漂移速度是否引起水面漂移物离散的研究

漂浮于自由水面的污染物的的迁移、扩散会受到天然随机海浪的影响。之前的研究（以Herterich和Hasselmann（1982）为代表）普遍认为,随机波浪作用下的斯托克司漂移速度会引起水面污染物的离散,这个离散甚至有可能跟风和海流引起的离散同一量级。本研究就随机波浪作用下的斯托克司漂移速度是否会引起水面漂移物的离散进行理论和试验探讨。从理论推导可知,随机波浪下的质量输移速度是个定常分量,因此它不会随时间变化而引起水面漂移物的离散。随后我们在实验室水槽中进行了漂移物在随机波浪（P-M谱）作用下的漂移过程的测量。试验结果也印证了随机波浪作用下的斯托克司漂移速度不会引起水面漂移物离散的结论。     

Shear Flow Dispersion Under Wave and Current

The longitudinal dispersion of solute in open channel flow with short period progressive waves is investigated. The waves induce second order drift velocity in the direction of propagation and enhance the mixing process in concurrent direction. The 1-D wave-period-averaged dispersion equation is derived and an expression for the wave-current induced longitudinal dispersion coefficient (WCLDC) is proposed based on Fischer's expression (1979) for dispersion in unidirectional flow. The result shows that the effect of waves on dispersion is mainly due to the cross-sectional variation of the drift velocity. Furthermore, to obtain a more practical expression of the WCLDC, the longitudinal dispersion coefficient due to Seo and Cheong (1998) is modified to incluee the effect of drift velocity. Laboratory experiments have been conducted to verify the proposed expression. The experimental results, together with dimensional analysis, show that the wave effect can be reflected by the ratio between the wave amplitude and wave period. A comparative study between the cases with and without waves demonstrates that the magnitude of the longitudinal dispersion coefficient is increased under the presence of waves.     

Wave-induced drift of an elliptical surface film

This study investigates experimentally the drift velocity of an elliptical surface film advected by deep-water waves. Thin polyethylene sheets were used to simulate the inextensible surface film. The drift velocities were obtained by recording and analyzing a sequence of images captured using a video camera. The results show that the drift velocity increases with the longitudinal length of the polyethylene sheet until approximately 0.8 times the wavelength. Beyond that, further increment would not result in substantial increase in the drift velocity. The effect due to the normalized transverse width is found to be significant within a particular range. At large wave steepness, the drift velocity appears to be limited by the Stokes drift. A set of best-fit empirical equations based on the sigmoidal function is introduced for oil spill trajectory prediction.     

Analysis of wave induced drift forces acting on a submerged sphere in finite water depth

A solution is presented for the wave induced drift forces acting on a submerged sphere in a finite water depth based on linearised velocity potential theory. In order to obtain the velocity potential, use has been made of multipole expansions in terms of an infinite series of Legendre functions with unknown coefficients. The series expression for the second order mean forces (drift forces) is provided by integrating the fluid pressure over the body surface. The horizontal drift force is also expressed by a series solution obtained using the far-field method.     

Wave drift enhancement effects in multi column structures

A theoretical assessment is made of mean wave drift forces on groups of vertical circular cylinders, such as the columns of a floating offshore platform. A complete analytical solution is obtained for two cylinders extending from seabed to free surface, and a long wave approximation is found to provide reliable predictions of the drift force in line with the waves at low frequencies. For moderate separation between the two cylinders, this force is found to tend at low frequencies to a value four times the force on an isolated cylinder.A numerical method is employed to study two surface piercing cylinders truncated below the free surface, and an arrangement of four vertical cylinders characteristic of a floating offshore platform. The mean vertical drift force is found to be reasonably well approximated, over the frequency range of practical interest, by the force on an individual cylinder considered in isolation multiplied by the number of cylinders in the group. Interaction effects, however, have a profound influence on the total horizontal drift force. At low frequencies this force is found to tend to the force on an isolated cylinder multiplied by the squate of the number of cylinders in the group.     

Second-order drift force response of offshore guyed towers

An iterative frequency domain method of analysis is presented for determining the response behaviour of Guyed Offshore Towers to low-frequency, second-order wave drift forces generated in a random sea environment. For the response analysis, the tower is idealized as a shear beam with a rotational spring at the bottom support. The guylines are replaced by a non-linear spring. The second-order drift force is considered to be proportional to the square of the wave elevation and is simulated using a drift force coefficient and the time history of a slowly varying wave envelope in random sea. The responses due to drift forces are obtained in frequency domain by incorporating the non-linearities produced due to non-linear guy lines. An example problem is solved under different random sea states to compare the response behaviour of the tower obtained by the second-order wave force, the first-order wave force and a combination of the two.     

A Numerical Study on Wave-Mud Interaction

1 .Introduction The dynamics of soft mud under surface water waves is of great importance to the sedimentationprocesses in approach channels and harbors ,and has long been drawing attention. Advancements innumerous engineering applications inthe shallowco…     

A quasi-cloaking phenomenon to reduce the wave drift force on an array of adjacent floating bodies

The mooring of offshore floating structures, such as offshore platforms, in large waves against drift forces and rotational moments is a challenging problem in offshore engineering. To accurately investigate such problems, called positioning problems, the time-averaged steady forces of the second order known as the wave drift forces must be taken into account. Fortunately, a cloaking phenomenon occurs under certain conditions and dramatically reduces the wave drift force acting on such a floating body, as previously reported by several researchers. In the diffraction problem of water waves, cloaking refers to the condition where there is no scattering in the form of radial outgoing waves. The reduction of wave drift force on a truncated cylinder with the occurrence of cloaking phenomenon has been numerically and experimentally confirmed. In this paper, the arrangement of several small circular cylinders at regular intervals in a circle concentric with a fixed floating body is considered as an effective means of reducing the wave drift force. Using a combination of a higher-order boundary element method (HOBEM) and wave interaction theory, the influences of the geometric parameters of the outer surrounding cylinders on the wave drift force and the total scattered-wave energy are systematically investigated and discussed. A quasi-cloaking phenomenon is first found and reported in the present study, which is beneficial and flexible for application in practical engineering. More than one quasi-cloaking trigger (where a trigger is an occurrence condition) can be found simply by varying the distance between the inner and outer floating bodies.     

Second-order oscillatory forces on a body in waves

When a small amplitude, water-wave train is incident upon a fixed body, a second-order analysis predicts that the body experiences a steady force and a force at twice the frequency of the incident wave. The double-frequency force is comprised of integrals of products of linear quantities over the surface of the body and the mean waterline and a term due to the second-order potential. An application of Green's theorem to the first-order potential and its horizontal derivative shows that the integral of the first order terms over the body is related in a simple way to the waterline integral and the far-field representation of the linear, diffraction potential. A minor modification of the analysis yields the farfield formulae for the drift force.     

Field investigations of the drift of artificial thin films on the sea surface

The results of field investigations of the drift of surface films are presented. The experiments were performed at the southern coast of the Crimea in the area of an oceanographic platform. It is shown that the drift of a thin film is described well by a linear combination of the vectors of the coastal current and wind, and the coefficient of the current velocity is close to unity. The total velocity of wind and wave drifts is 0.013 of the wind velocity magnitude or 0.38 of the air friction velocity. Analysis of experimental data demonstrates an increase in the film spreading rate with increasing wind velocity.     

Numerical study on the reverse drift force of floating BBDB wave energy absorbers

The motions and time-mean horizontal drift forces of floating backward-bent duct buoy wave energy absorbers in regular waves are calculated taking account of the oscillating surface-pressure due to the pressure drop in the air chamber above the oscillating water column within the scope of the linear wave theory. The present numerical results show that the time-mean drift forces of backward-bent duct buoys are in the reverse direction of propagation of the incident waves over specific frequency ranges as found by McCormick through his experimental work. The drift force has been calculated by the near-field method. A brief discussion on Maruo’s formula which shows that the time-mean drift force must be in the direction of propagation of the incident waves, has also been presented.     

Minimization of drift force on a floating cylinder by optimizing the flexural rigidity of a concentric annular plate

The deployment of suitable configurations of mutually interacting floating bodies for efficiently controlling their hydrodynamic interactions towards the reduction of the wave drift forces and, thus, of the mooring lines’ loads, has, nowadays, gained a great scientific interest. In this paper, the hydrodynamic behaviour of a floating cylinder and a concentric annular flexible plate is analysed in the frequency domain aiming at the minimization of the drift forces acting on the cylinder by optimizing the flexural rigidity of the plate. The diffraction/radiation problem is solved using a higher-order boundary element method. The analysis is implemented assuming that both floating bodies oscillate freely in heave, while for the plate, flexible modes are, additionally, considered for describing its structural deformations. The required modes shapes are determined in vacuum (“dry” mode superposition approach) through analytical expressions. The flexural rigidity of the plate, D, is optimized at a specific wave number using a real-coded genetic algorithm. Initially, results are compared with numerical results of other investigators for the case of two rigid concentric floating cylinders. Next, extended results are presented, focusing on the effect of D, including its optimum value, on various physical quantities describing the behaviour of both the cylinder and the plate. Contrary to the isolated cylinder, the presence of the plate introduces sharp peaks in the variation pattern of the drift force of the cylinder, bounded at specific wave numbers, where resonance of the seiche mode of water motion in the annular cavity or of specific flexible modes of the plate occurs. However, by reducing D to its optimum value, the cylinder’s drift force obtains practically zero values at the target wave number, due to an efficient improvement of the wave field in the annular cavity around the cylinder. Moreover, a great reduction of the drift force compared to the isolated cylinder is achieved in the subsequent high frequency range.     

On the effects of wave drift on the dispersion of floating pollutants

The movement of floating pollutants such as oil slicks on the surface of the sea is due to a number different factors, among which wave drift is certainly significant.In principle, it has been known since Stokes' time that a floating particle is subject to the movement caused by the orbital motion of water particles and that an average drift velocity results because the trajectories are not closed. In the past, however, this effect was often either disregarded or simply included with the surface wind induced current. In recent times the difference between the two effects has been conceptually clarified, so that the average wave drift in random one-dimensional seas has been the object of research and the results are now included in most handbooks and models for oil slick forecasting.Due to the chaotic nature of the wave field, however, the drift also causes floating substances to disperse, and this phenomenon is a much more neglected area of research. Recent work by Bovolin et al. [IAHR Congress, 1997] and Sobey and Barker [J. Coast. Res. 13 (1997)] has brought the subject to attention, and computational tools can now be made to quantify the effect and to verify when and how it should be taken into consideration in oil slick accident practise.The work presented in this paper is based on random simulation of the wave induced Eulerian velocity field in a directional sea, by making use of standard offshore wave directional models and on the ensemble averaging of floating particles trajectories in order to compute the spatial dispersion.     

The influence of Stokes drift on oil spills: Sanchi oil spill case

Spilled oil floats and travels across the water’s surface under the influence of wind, currents, and wave action. Wave-induced Stokes drift is an important physical process that can affect surface water particles but that is currently absent from oil spill analyses. In this study, two methods are applied to determine the velocity of Stokes drift, the first calculates velocity from the wind-related formula based upon a one-dimensional frequency spectrum, while the second determines velocity directly from the wave model that was based on a two-dimensional spectrum. The experimental results of numerous models indicated that: (1) oil simulations that include the influence of Stokes drift are more accurate than that those do not; (2) for medium and long-term simulations longer than two days or more, Stokes drift is a significant factor that should not be ignored, and its magnitude can reach about 2% of the wind speed; (3) the velocity of Stokes drift is related to the wind but is not linear. Therefore, Stokes drift cannot simply be replaced or substituted by simply increasing the wind drift factor, which can cause errors in oil spill projections; (4) the Stokes drift velocity obtained from the two-dimensional wave spectrum makes the oil spill simulation more accurate.     

波频和慢漂组合作用下钢悬链线立管疲劳损伤研究

为了有效地考虑浮体慢漂运动对钢悬链线立管疲劳损伤的影响,提出了波频和慢漂运动组合作用下钢悬链线立管疲劳损伤简化计算的位置组合叠加法。其核心是:基于浮体慢漂运动概率分布选取若干典型慢漂位置,进行波频运动作用下钢悬链线立管动力响应分析;根据钢悬链线立管运动位置变化特征,截取若干慢漂位置对应的波频应力时程叠加到慢漂应力时程上,得到波频和慢漂运动的组合应力时程;编写基于雨流计数法的MATLAB程序处理立管各节点应力,采用海水环境下Do E.E型S-N曲线和Palmgren-Miner累积损伤准则计算立管各节点疲劳损伤。应用位置组合叠加法对某海域500 m水深的立管进行了疲劳分析,并与全耦合法、权重组合叠加法以及波频和慢漂疲劳损伤简单相加法的结果进行了对比,结果表明该方法具有较高的精度和效率。此外,进行了区域设定系数、波浪高度、波浪周期和土壤表面剪切强度等参数对组合作用下立管疲劳损伤的敏感性分析。     

Nonlinear Dynamic Analysis of Deepwater Drilling Risers Subjected to Random Loads

Excited by ocean currents, random wave and vessel motion, deepwater drilling risers exhibit significant dynamic response. In time domain, a method is proposed to calculate the nonlinear dynamic response of deepwater drilling risers subjected to random wave and dynamic large displacement vessel motion boundary condition. Structural and functional loads, external and internal pressure, free surface effect of irregular wave, hydrodynamic forces induced by current and wave, as well as wave and low frequency (drift) motion of the drilling vessel are all accounted for. An example is presented which illustrates the application of the proposed method. The study shows that long term drift motion of the vessel has profound effect on the envelopes of bending stress and lateral displacement, as well as the range of lower flex joint angle of the deepwater riser. It can also be concluded that vessel motion is the principal dynamic loading of nonlinear dynamic response for the deepwater risers rather than wave force.     

An experimental study of the surface drift currents in a wave flume

The Lagrangian surface drift current induced by surface gravity waves in a wave flume has been investigated experimentally by the particle tracking method. It was observed that in most regions of the flume, the time-mean surface drift current was in the opposite direction to that of the wave propagation. The secondary current in the form of a pair of longitudinal vortices caused by the lateral boundaries was analyzed. It is suggested that the convection of the vorticity generated by the wave-absorber and the lateral boundaries is an important factor in the determination of the time-mean drift in a wave flume.     

Prediction of drift in a free surface

An analytical model including the boundary-layer effect is developed to find the steady drift induced by the non-linear effect of the surface-wave motion. The analytical result is compared with the experimental results obtained from a wave tank. Results show a qualitative agreement. A semi-empirical formula which predicts drift velocity of a contaminant layer on the free surface is introduced and its validity is investigated.     

Third order wave force on axisymmetric bodies

The third order triple-frequency wave load on fixed axisymmetric bodies by monochromatic waves is considered within the frame of potential theory. Waves are assumed to be weak non-linearity and a perturbation method is used to expand velocity potentials and wave loadings into series according to a wave steepness of kA. Integral equation method is used to compute velocity potentials up to second order in wave steepness. The third order triple-frequency wave loads are computed by an indirect method and an efficient method is applied to form the third order forcing term on the free surface quickly. The method can be used to compute third order triple-frequency surge force, heave force and pitch moment on any revolution bodies with vertical axes. The comparison with Malenica and Molin's results is made on surge force on a uniform cylinder, and comparison with experimental results is made on third order surge force, heave force and pitch moment on a truncated cylinder. More numerical computations are carried out for third order forces and moments on a uniform cylinder, truncated cylinders and a hemisphere.     

Mean drift forces on an articulated column oscillating in a wave tank

An analytical solution is presented for calculating the regular wave induced respones of an articulated column in a wave tank. Extension of the procedure leads to calculation of second order mean drift forces and moments. Hydrodynamic interaction between a cylindrical column and the parallel walls of the tank is shown theoretically to be highly significant and experimental data are presented to corroborate this finding.