Medium-term effects of two landsliding episodes on channel storage of sediment

Two landsliding episodes between late 1973 and early 1975 delivered about 60000 m³ of sediment to six small deeply incised streams draining a 2·7 km² area. About 4700 m³ of logs in the landslide debris formed major log jams in five streams, which impounded large volumes of landslide-derived sediment. Five years after the landsliding, 42 per cent (25000 m³) of sediment was still in storage behind 35 log jams ranging from 1·4–8·2 m high. The landsliding episodes have produced multi-stepped stream profiles, aggradation of channel reaches up to 150 m long to mean depths between 1·2 and 4·1 m, reductions in gradient, fining of bed material size, and related changes in bedforms and channel width:depth ratios that seem likely to persist for at least several decades. Sediment presently stored behind log jams is equivalent to between 50 and 220 years normal supply of sediment from hillslopes to stream channels. Long-delayed, large magnitude impacts on higher-order channels may occur if sudden failure of log jams is induced by a large storm at some future date.     

Large wood in central Appalachian headwater streams: controls on and potential changes to wood loads from infestation of hemlock woolly adelgid

Large wood (LW) is an important component of forested headwater streams. The character of LW loads reflects a balance between adjacent valley processes that deliver LW to the channel (herein recruitment processes) and stream channel processes that either retain or transport LW through the reach (herein retention processes). In the central Appalachian Mountains, USA, LW characteristics in headwater streams located in eastern hemlocks (Tsuga candensis) forests are expected to change because of infestation of hemlock woolly adelgid (Adelges tsugae, HWA), an exotic, invasive insect. We examined LW characteristics in 24 headwater streams ranging from un‐infested to severe infestation, as determined by hemlock canopy health. The objectives of this work were to: (i) quantify wood loads; (ii) assess the relative importance of valley recruitment and in‐stream retention mechanisms in controlling reach‐scale wood loads; and (iii) assess if there was a detectable influence of HWA on LW loads. We hypothesized that LW loads would be similar to other forested streams in eastern USA and dominated by recruitment processes. In addition, higher LW loads would correspond with advanced HWA infestation. Mean wood frequency was 38 pieces/100 m ± 17 (standard deviation); mean wood volume was 3.69 m³/100 m ± 2.76. In general, LW load characteristics were influenced by both recruitment and retention parameters; jam (accumulations ≥ 3 pieces) characteristics were dominated by retention parameters. Results suggest that adjacent stand basal area influences LW loads and once LW is recruited to the channel, streams lack sufficient hydraulic driving forces, despite having lower resistance structures, to transport LW out of the reach. Sites in moderate decline had higher proportions of short (1–2 m and 1–4 m) and very long (>10 m) LW with higher frequency of jams that were low in volume. We present a hypothesized conceptual model of expected changes to LW loads associated with HWA infestation and hemlock mortality. Copyright © 2015 John Wiley & Sons, Ltd.     

Geomorphic and stream flow influences on large wood dynamics and displacement lengths in high gradient mountain streams (Chile)

Understanding large wood (LW; ≥1 m long and ≥10 cm in diameter) dynamics in rivers is critical for many disciplines including those assessing flood hazard and risk. However, our understanding of wood entrainment and deposition is still limited, mainly because of the lack of long‐term monitoring of wood‐related processes. The dataset presented here was obtained from more than 8 years of monitoring of 1,264 tagged wood pieces placed in 4 low‐order streams of the Chilean mountain ranges and was used to further our understanding of key factors controlling LW dynamics. We show that LW displacement lengths were longer during periods when peak‐flow water depths (H_max) exceeded the bankfull stage (H_Bk) than in periods with H_max ≤ H_Bk and that these differences were significantly higher for smaller wood pieces. LW length and length relative to channel dimensions were the main factors governing LW entrainment; LW displacement lengths were inversely related to the ratio of piece length to H_15% (i.e., the level above which the flow remains for 15% of the time) and to the ratio of H_15% to bankfull width. Unrooted logs and LW pieces located at the bankfull stage travelled significantly longer distances than logs with attached rootwads and those located in other positions within the bankfull channel. A few large logjams were broken during the period of observation, and in all occasions, LW from these broken logjams did not travel over longer distances than other pieces of LW moved in the same periods and in the same stream segments. Most importantly, our work reveals that LW dynamics tend to be concentrated within a few reaches in each stream and that reaches exhibiting high wood dynamics (extensive entrainment, deposition, or repositioning of LW) are significantly wider and less steep than less dynamic reaches.     

Effects of forest stand age on the characteristics of logjams in mountainous forest streams

We measured longitudinal spacing and wood volume of channel‐spanning logjams along 30 1‐km reaches of forest streams in the Colorado Front Range, USA. Study streams flow through old‐growth (> 200 year stand age) or younger subalpine conifer forest. Evaluating correlations between the volume and longitudinal spacing of logjams in relation to channel and forest characteristics, we find that old‐growth forest streams have greater in‐stream wood loads and more jams per kilometer than streams in younger forest. Old‐growth forests have a larger basal area close to the stream and correlate with larger piece diameters of in‐stream wood. Jam volume correlates inversely with the downstream spacing for ramp and bridge pieces that can act as key pieces in jams. Most importantly, old‐growth streams have shorter downstream spacing for ramp and bridge pieces (< 20 m). Our results suggest that management of in‐stream wood and associated stream characteristics can be focused most effectively at the reach scale, with an emphasis on preserving old‐growth riparian stands along lower gradient stream reaches or mimicking the effects of old growth by manipulating the spacing of ramp and bridge pieces. Our finding that average downstream spacing between jams declines as wood load increases suggests that the most effective way to create and retain jams is to ensure abundant sources of wood recruitment, with a particular emphasis on larger pieces that are less mobile because they have at least one anchor point outside the active channel. Copyright © 2014 John Wiley & Sons, Ltd.     

Investigating the linkage between streamflow recession rates and channel network contraction in a mesoscale catchment in New York state

The rate of recession (dQ/dt) in a given time interval has long been plotted in log–log space against the concurrent mean discharge (Q_avg). Recent interpretations of these dQ/dt–Q_avg plots have sought to look at curves for individual events instead of the data cloud from all the data points together. These individual recession curves have been observed to have near‐constant slope but to have varying intercepts, features hypothesized to possibly be explained by the nature of the contraction of the active channel network during recession. For a steep, 150‐ha forested catchment in central New York state with an 8.8‐km channel network, changes in the active channel network were mapped between April and November 2013. Streamflow recession occurred in a matter of days, but changes in the active channel network occurred over a matter of weeks. Thus, in this catchment, it does not appear that channel contraction directly controls recession. Additionally, field observations indicate that dry down did not occur in a spatially organized, sequential way such that the upper end of higher‐order streams dried first. Instead, the location of groundwater seeps, in part, controlled the active portion of the channel network. Consistent with the presence of different types of flow contributing zones, the paper presents a conceptual model that consists of multiple parallel reservoirs of varying drainage rate and varying degrees of recharge at different times of the year. This conceptual model is able to reproduce a slope of 2 and a seasonal shift in intercept typical of individual recession curves. Copyright © 2015 John Wiley & Sons, Ltd.     

Channel flow competence and sediment transport in upland streams in southeast Australia

Bedload transport data from planebed and step‐pool reach types are used to determine grain size transport thresholds for selected upland streams in southeast Australia. Morphological differences between the reach types allow the effects of frictional losses from bedforms, microtopography and bed packing to be incorporated into the dimensionless critical shear stress value. Local sediment transport data are also included in a regime model and applied to mountain streams, to investigate whether empirical data improve the delineation of reach types on the basis of dimensionless discharge per unit width (q*) and dimensionless bedload transport (q_b*). Instrumented planebed and step‐pool sites are not competent to transport surface median grains (D_50s) at bankfull discharge (Q_bf). Application of a locally parametrized entrainment equation to the full range of reach types in the study area indicates that the majority of cascades, cascade‐pools, step‐pools and planebeds are also not competent at Q_bf and require a 10 year recurrence interval flood to mobilize their D_50s. Consequently, the hydraulic parameters of the regime diagram, which assume equilibrium conditions at bankfull, are ill suited to these streams and provide a poor basis of channel delineation. Modifying the diagram to better reflect the dominant transported bedload size (equivalent to the D₁₆ of surface sediment) made only slight improvements to reach delineation and had greatest effect on the morphologies with smaller surface grain sizes such as forced pool‐riffles and planebeds. Likewise, the Corey shape factor was incorporated into the regime diagram as an objective method for adjusting a base dimensionless critical shear stress (τ*_c50b) to account for lithologically controlled grain shape on bed packing and entrainment. However, it too provided only minor adjustments to reach type delineation. Copyright © 2007 John Wiley & Sons, Ltd.     

Decadal-scale changes in suspended wood after riparian recruitment in managed stands in headwater streams of coastal British Columbia,Canada

Large wood (LW) affects several ecological and hydrogeomorphic processes in streams. The main source of LW is riparian trees falling inside channels. However, in confined valley floors, falling trees are more likely to be suspended above the channel. Eventually, these suspended trees will decompose and break to finally fall into the channel to better provide functions for streams. We evaluated changes in wood decay, length, diameter, and suspended status (suspended or non-suspended) 17 years post-harvest and nine years after the first sampling occurred in 2006 in 12 headwater streams of coastal British Columbia, Canada. We also evaluated whether changes differed among riparian management treatments (no-harvest buffers of 10 and 30 m in width, thinning, and unharvested reference sites), and identified the factors affecting wood changes and suspended status. Wood pieces advanced in decay, became shorter, and 34% of them (n = 108) changed status from suspended to non-suspended. Non-suspended wood pieces were more decayed and shorter than suspended wood. Suspended wood was longer, thicker, less decayed, and represented 46.5% (n = 147) of the wood sampled in 2006. Our findings revealed limited influences of riparian management on many aspects of wood changes considered in this study. Changes in wood characteristics were more likely for pieces that were smaller in diameter, longer, and suspended closer to the water. The transition from suspended to non-suspended LW can be a long-term process that can increase wood residence time and reduce LW in-stream functions particularly in confined stream valleys. The suspended stage is also an important mechanism underlying time lags in stream ecosystem responses to riparian tree fall. © 2020 John Wiley & Sons, Ltd.     

Processes and rates of sediment and wood accumulation in headwater streams of the Oregon Coast Range,USA

Channels that have been scoured to bedrock by debris flows provide unique opportunities to calculate the rate of sediment and wood accumulation in low‐order streams, to understand the temporal succession of channel morphology following disturbance, and to make inferences about processes associated with input and transport of sediment. Dendrochronology was used to estimate the time since the previous debris flow and the time since the last stand‐replacement fire in unlogged basins in the central Coast Range of Oregon. Debris flow activity increased 42 per cent above the background rate in the decades immediately following the last wildfire. Changes in wood and sediment storage were quantified for 13 streams that ranged from 4 to 144 years since the previous debris flow. The volume of wood and sediment in the channel, and the length of channel with exposed bedrock, were strongly correlated with the time since the previous debris flow. Wood increased the storage capacity of the channel and trapped the majority of the sediment in these steep headwater streams. In the absence of wood, channels that have been scoured to bedrock by a debris flow may lack the capacity to store sediment and could persist in a bedrock state for an extended period of time. With an adequate supply of wood, low‐order channels have the potential of storing large volumes of sediment in the interval between debris flows and can function as one of the dominant storage reservoirs for sediment in mountainous terrain. Copyright © 2003 John Wiley & Sons, Ltd.     

Environmental controls of wood entrapment in upper Midwestern streams

Wood deposited in streams provides a wide variety of ecosystem functions, including enhancing habitat for key species in stream food webs, increasing geomorphic and hydraulic heterogeneity and retaining organic matter. Given the strong role that wood plays in streams, factors that influence wood inputs, retention and transport are critical to stream ecology. Wood entrapment, the process of wood coming to rest after being swept downstream at least 10 m, is poorly understood, yet important for predicting stream function and success of restoration efforts. Data on entrapment were collected for a wide range of natural wood pieces (n = 344), stream geomorphology and hydraulic conditions in nine streams along the north shore of Lake Superior in Minnesota. Locations of pieces were determined in summer 2007 and again following an overbank stormflow event in fall 2007. The ratio of piece length to effective stream width (length ratio) and the weight of the piece were important in a multiple logistic regression model that explained 25% of the variance in wood entrapment. Entrapment remains difficult to predict in natural streams, and often may simply occur wherever wood pieces are located when high water recedes. However, this study can inform stream modifications to discourage entrapment at road crossings or other infrastructure by applying the model formula to estimate the effective width required to pass particular wood pieces. Conversely, these results could also be used to determine conditions (e.g. pre‐existing large, stable pieces) that encourage entrapment where wood is valued for ecological functions. Copyright © 2010 John Wiley & Sons, Ltd.     

A conceptual model for the longitudinal distribution of wood in mountain streams

Wood load, channel parameters and valley parameters were surveyed in 50 contiguous stream segments each 25 m in length along 12 streams in the Colorado Front Range. Length and diameter of each piece of wood were measured, and the orientation of each piece was tallied as a ramp, buried, bridge or unattached. These data were then used to evaluate longitudinal patterns of wood distribution in forested headwater streams of the Colorado Front Range, and potential channel‐, valley‐ and watershed‐scale controls on these patterns. We hypothesized that (i) wood load decreases downstream, (ii) wood is non‐randomly distributed at channel lengths of tens to hundreds of meters as a result of the presence of wood jams and (iii) the proportion of wood clustered into jams increases with drainage area as a result of downstream increases in relative capacity of a stream to transport wood introduced from the adjacent riparian zone and valley bottom. Results indicate a progressive downstream decrease in wood load within channels, and correlations between wood load and drainage area, elevation, channel width, bed gradient and total stream power. Results support the first and second hypotheses, but are inconclusive with respect to the third hypothesis. Wood is non‐randomly distributed at lengths of tens to hundreds of meters, but the proportion of pieces in jams reaches a maximum at intermediate downstream distances within the study area. We use these results to propose a conceptual model illustrating downstream trends in wood within streams of the Colorado Front Range. Copyright © 2009 John Wiley & Sons, Ltd.     

Hydraulic characteristics of a small Coastal Plain stream of the southeastern United States: effects of hydrology and season

Various physical and biological properties affect solute transport patterns in streams. We measured hydraulic characteristics of Payne Creek, a low‐gradient upper Coastal Plain stream, using tracer experiments and parameter estimation with OTIS‐P (one‐dimensional transport with inflow and storage with parameter optimization). The primary objective of this study was to estimate the effects of varying discharge, season, and litter accumulation on hydraulic parameters. Channel area A ranged from 0·081 to 0·371 m² and transient storage area A_s ranged from 0·027 to 0·111 m². Dispersion D ranged from 1·5 to 11·1 m² min⁻¹ and exchange coefficient α ranged from 0·009 to 0·038 min⁻¹. Channel area and dispersion were positively correlated to discharge Q, whereas storage area and exchange coefficient were not. Relative storage size A_s/A ranged from 0·17 to 0·59, and was higher during fall than other seasons under a similar Q. The fraction of median travel time due to transient storage ranged from 8·8 to 34·5% and was significantly correlated with Q through a negative power function. Both metrics indicated that transient storage was a significant component affecting solute transport in Payne Creek, especially during the fall. Comparison between the measured channel area A_c and A suggested that surface storage was dominant in Payne Creek. During fall, accumulation of leaf litter resulted in larger A and A_s and lower velocity and D than during other seasons with similar discharge. Seasonal changes in discharge and organic matter accumulation, and dynamic channel morphology affected the magnitude of transient storage and overall hydraulic characteristics of Payne Creek. Copyright © 2005 John Wiley & Sons, Ltd.     

Sediment transport capacity and erosion processes: model concepts and reality

Sediment transport capacity, T_c, defined as the maximum amount of sediment that a flow can carry, is the basic concept in determining detachment and deposition processes in current process-based erosion models. Although defined conceptually and used extensively in modelling erosion, T_c was rarely measured. Recently, a series of laboratory studies designed to quantify effects of surface hydrologic conditions on erosion processes produced data sets feasible to evaluate the concept of T_c. A dual-box system, consisting of 1·8 m long sediment feeder box and a 5 m long test box, was used. Depending on the relative magnitudes of sediment delivery from feeder and test boxes, five scenarios are proposed ranging from deposition-dominated to transport-dominated sediment regimes. Results showed that at 5 per cent slope under seepage or 10 per cent slope under drainage conditions, the runoff from the feeder box caused in the additional sediment transport in the test box, indicating a transport-dominated sediment regime. At 5 per cent slope under drainage conditions, deposition occurred at low rainfall intensities. Increases in slope steepness, rainfall intensity and soil erodibility shifted the dominant erosion process from deposition to transport. Erosion process concepts from the Meyer–Wishmeier, Foster–Meyer and Rose models were compared with the experimental data, and the Rose model was found to best describe processes occurring during rain. A process-based erosion model needs to have components that can represent surface conditions and physical processes and their dynamic interactions. Copyright © 1999 John Wiley & Sons, Ltd.     

Long-term large wood load fluctuations in two low-order streams in Southern Chile

The eco-hydrogeomorphic significance of large wood (LW) and its potential for increasing downstream hazards during extreme floods have been widely recognized. We used LW data collected for a 10-year period from the two low-order streams of Pichún (Pi) and Vuelta de Zorra (VZ) in Southern Chile to (a) determine if the abundance and dimensions of individual LW pieces change with time, (b) quantify wood load fluctuations during the 10-year period, and (c) assess the role of LW recruitment from the riparian forests to explain wood load fluctuations during the study period. Nine years after the first survey, the number of LW pieces in Pi and VZ diminished by 60 and 40%, respectively. Despite the reduction in these numbers, in Pi, the LW dimensions did not change significantly during the study. In VZ, the dimensions exhibited statistically significant differences, despite being within the same class. In both catchments, the LW load fluctuated during a 10-year period, but the drivers of change differed. Although tree toppling was the recruitment mechanism responsible for LW in both stream cases, the high wood load measured in Pi at the beginning of the study suggested massive tree recruitments before the first survey, followed by wood exports which were higher than inputs in the subsequent 10-year period. In VZ, LW load decreased during the first 9 years (mean annual rate of ~9.2 m³ year⁻¹) and then increased by ~12.1 m³ year⁻¹ in year 10. At VZ, the inputs consisted of single trees that were recruited from the riparian area and by upstream flotation, while exports occurred by downstream fluvial transport. Wood inputs and exports occurred asynchronously and led to LW load fluctuations at decadal and annual intervals. Land management and tree species thus exert a major influence on wood inventory and budget in streams. © 2020 John Wiley & Sons, Ltd.     

Distribution and characterization of in‐channel large wood in relation to geomorphic patterns on a low‐gradient river

A 177 river km georeferenced aerial survey of in‐channel large wood (LW) on the lower Roanoke River, NC was conducted to determine LW dynamics and distributions on an eastern USA low‐gradient large river. Results indicate a system with approximately 75% of the LW available for transport either as detached individual LW or as LW in log jams. There were approximately 55 individual LW per river km and another 59 pieces in log jams per river km. Individual LW is a product of bank erosion (73% is produced through erosion) and is isolated on the mid and upper banks at low flow. This LW does not appear to be important for either aquatic habitat or as a human risk. Log jams rest near or at water level making them a factor in bank complexity in an otherwise homogenous fine‐grained channel. A segmentation test was performed using LW frequency by river km to detect breaks in longitudinal distribution and to define homogeneous reaches of LW frequency. Homogeneous reaches were then analyzed to determine their relationship to bank height, channel width/depth, sinuosity, and gradient. Results show that log jams are a product of LW transport and occur more frequently in areas with high snag concentrations, low to intermediate bank heights, high sinuosity, high local LW recruitment rates, and narrow channel widths. The largest concentration of log jams (21.5 log jams/km) occurs in an actively eroding reach. Log jam concentrations downstream of this reach are lower due to a loss of river competency as the channel reaches sea level and the concurrent development of unvegetated mudflats separating the active channel from the floodplain forest. Substantial LW transport occurs on this low‐gradient, dam‐regulated large river; this study, paired with future research on transport mechanisms should provide resource managers and policymakers with options to better manage aquatic habitat while mitigating possible negative impacts to human interests. Copyright © 2011 John Wiley & Sons, Ltd.     

Estimation of temporally averaged sediment delivery ratio using aggradational terraces in headwater catchments of the Waipaoa River,North Island,New Zealand

The sediment delivery ratio was estimated for two periods (28 years and eight years) following reforestation of seven tributary catchments (0·33 to 0·49 km²) in the headwaters of the Waipaoa River basin, North Island, New Zealand. In these catchments, gully erosion, which largely resulted from clearance of the natural forest between 1880 and 1920, is the main source of sediment to streams. Reforestation commenced in the early 1960s in an attempt to stabilize hillslopes and reduce sediment supply. Efforts have been partially successful and channels are now degrading, though gully erosion continues to supply sediment at accelerated rates in parts of the catchment. Data from the area indicate that the sediment delivery ratio (SDR) can be estimated as a function of two variables, ψ (the product of catchment area and channel slope) and A _g (the temporally averaged gully area for the period). Sediment input from gullies was determined from a well defined relationship between sediment yield and gully area. Sediment scoured from channels was estimated from dated terrace remnants and the current channel bed. Terrace remnants represent aggradation during major floods. This technique provides estimates of SDR averaged over periods between large magnitude terrace‐forming events and with the present channel bed. The technique averages out short‐term variability in sediment flux. Comparison of gully area and sediment transport between two periods (1960–1988 and 1988–1996) indicates that the annual rate of sediment yield from gullies for the later period has decreased by 77 per cent, sediment scouring in channels has increased by 124 per cent, and sediment delivered from catchments has decreased by 78 per cent. However, average SDR for the tributaries was found to be not significantly different between these periods. This may reflect the small number of catchments examined. It is also due to the fact that the volume of sediment scoured from channels was very small relative to that produced by gullies. According to the equation for SDR determined for the Waipaoa headwaters, SDR increases with increasing catchment area in the case where A _g and channel slope are fixed. This is because the amount of sediment produced from a channel by scouring increases with increasing catchment area. However, this relationship does not hold for the main stem of the study catchments, because sediment delivered from its tributaries still continues to accumulate in the channel. Higher order channels are, in effect, at a different stage in the aggradation/degradation cycle and it will take some time until a main channel reflects the effects of reforestation and its bed adjusts to net degradation. Results demonstrate significant differences among even low order catchments, and such differences will need to be taken into consideration when using SDR to estimate sediment yields. Copyright © 2001 John Wiley & Sons, Ltd.     

A flume experiment on wood storage and remobilization in braided river systems

This work investigates wood dynamics in braided streams through physical modelling in a mobile bed laboratory flume, with the specific objective to characterize wood storage and turnover as a function of wood input rate and of wood element type. Three parallel channels (1.7 m wide, 10 m long) filled with uniform sand were used to reproduce braided networks with constant water discharge and sediment feeding. Wood dowels with and without simplified root wads were regularly added at the upstream end of each flume at different input rates, with a 1:2:3 ratio between the three flumes. Temporal evolution of wood deposition patterns and remobilization rates were monitored by a series of vertical images that permitted the recognition of individual logs. Results show that wood tends to disperse in generally small accumulations (< 5 logs), with higher spatial density on top of sediment bars, and is frequently remobilized due to the intense morphological changes. The amount of wood stored in the channel depends on log input rate through a non‐linear relationship, and input rates exceeding approximately 100 logs/hour determine a sharp change in wood dynamics, with higher storage volume and augmented formation of large jams (> 10 elements) that are less prone to remobilization. Presence of root wads seems to play a minor role in wood deposition, but it reduces the average travel distance of logs. Turnover rates of logs were similar in the three flumes, independently of wood input rate and largely resembling the turnover rate of exposed bars. For the simulated conditions, significant effects of wood on bed morphology were not observed, suggesting that interactions with fine sediments and living vegetation are crucial to form large, stable wood jams able to bring about relevant morphological changes. Copyright © 2014 John Wiley & Sons, Ltd.     

Surface particle sizes on armoured gravel streambeds: effects of supply and hydraulics

Most gravel‐bed streams exhibit a surface armour in which the median grain size of the surface particles is coarser than that of the subsurface particles. This armour has been interpreted to result when the supply of sediment is less than the ability of the stream to move sediment. While there may be certain sizes in the bed for which the supply is less than the ability of the stream to transport these sizes, for other sizes of particles the supply may match or even exceed the ability of the channel to transport these particles. These sizes of particles are called ‘supply‐limited’ and ‘hydraulically limited’ in their transport, respectively, and can be differentiated in dimensionless sediment transport rating curves by size fractions. The supply‐ and hydraulically limited sizes can be distinguished also by comparing the size of particles of the surface and subsurface. Those sizes that are supply‐limited are winnowed from the bed and are under‐represented in the surface layer. Progressive truncation of the surface and subsurface size distributions from the ?ne end and recalculation until the size distributions are similar (collapse), establishes the break between supply‐ and hydraulically limited sizes. At sites along 12 streams in Idaho ranging in drainage area from about 100 to 4900 km², sediment transport rating curves by size class and surface and subsurface size distributions were examined. The break between sizes that were supply‐ and hydraulically limited as determined by examination of the transport rate and surface and subsurface size distributions was similar. The collapse size as described by its percentile in the cumulative size distribution averaged D₃₆ of the surface and D₇₃ of the subsurface. The discharge at which the collapse size began to move averaged 88 per cent of bankfull discharge. The collapse size decreased as bed load yield increased and increased with the degree of selective transport. Copyright © 2003 John Wiley & Sons, Ltd.     

A rational sediment transport scaling relation based on dimensionless stream power

The concept of stream channel grade – according to which a stream channel reach will adjust its gradient, S, in order to transport the imposed sediment load having magnitude Q_b and characteristic grain size D_b, with the available discharge Q (Mackin, 1948 , Geological Society of America Bulletin 59 : 463–512; Lane, 1955 , American Society of Civil Engineers, Proceedings 81 : 1–17) is one of the most influential ideas in fluvial geomorphology. Herein, we derive a scaling relation that describes how externally imposed changes in either Q_b or Q can be accommodated by changes in the channel configuration, described by the energy gradient, mean flow depth, characteristic grain size and a parameter describing the effect of bed surface structures on grain entrainment. One version of this scaling relation is based on the dimensionless bed material transport parameter (W*) presented by Parker and Klingeman ( 1982 , Water Resources Research 18 : 1409–1423). An equivalent version is based on a new dimensionless transport parameter (E*) using dimensionless unit stream power. This version is nearly identical to the relation based on W*, except that it is independent of flow resistance. Both versions of the scaling relation are directly comparable to Lane's original relation. In order to generate this stream power‐based scaling relation, we derived an empirical transport function relation relating E* to dimensionless stream power using data from a wide range of stable, bed load‐dominated channels: the form of that transport function is based on the understanding that, while grain entrainment is related to the forces acting on the bed (described by dimensionless shear stress), sediment transport rate is related to the transfer of momentum from the fluid to the bed material (described by dimensionless stream power). Copyright © 2010 John Wiley & Sons, Ltd.     

Transport and dispersal of organic debris (peat blocks) in upland fluvial systems

This paper assesses the mechanisms and pathways by which peat blocks are eroded and transported in upland fluvial systems. Observations and experiments from the north Pennines (UK) have been carried out on two contrasting river systems. Mapping of peat block distributions and appraisal of reach‐based sediment budgets clearly demonstrates that macro‐size peat is an important stream load component. In small streams block sizes can approximate the channel width and much of the peat is transported overbank. Local ‘peat jams’ and associated mineral deposition may provide an important component of channel storage. In larger systems peat blocks rapidly move down‐channel and undergo frequent exchanges between bed and bank storage. Results of peat block tracing using painted blocks indicate that once submerged, blocks of all sizes are easily transported and blocks break down rapidly by abrasion. Vegetation and bars play an important role in trapping mobile peat. In smaller streams large block transport is limited by channel jams. Smaller blocks are transported overbank but exhibit little evidence of downstream fining. In larger rivers peat blocks are more actively sorted and show downstream reduction in size from source. A simple model relating peat block diameter (D_p) to average flow depth (d) suggests three limiting transport conditions: flotation (D_p < d), rolling (d < D_p > d/2) and deposition (D_p > d/2). Experiments demonstrate that peat block transport occurs largely by rolling and floating and the transport mechanism is probably controlled by relative flow depth (d/D_p ratio). Transport velocity varies with transport mechanism (rolling is the slowest mode) and transport lengths increase as flow depth increases. Abrasion rates vary with the transport mechanism. Rolling produces greater abrasion rates and more rounded blocks. Abrasion rates vary from 0 to 10 g m^?1 for blocks ranging in mass from 10 to 6000 g. Copyright © 2001 John Wiley & Sons, Ltd.     

Decadal changes in distribution and frequency of wood in a free meandering river,the Ain River,France

This study examined the temporal dynamics and longitudinal distribution of wood over a multi‐decadal timescale at the river reach scale (36 km) and a meander bend scale (300–600 m) in the Ain River, a large gravel‐bed river flowing through a forested corridor, and adjusting to regulation and floodplain land‐use change. At the 36 km scale, more wood was recruited by bank erosion in 1991–2000 than since the 1950s. The longitudinal distribution of accumulations was similar between 1989 and 1999, but in both years individual pieces occurred homogeneously throughout the reach, while jam distribution was localized, associated with large concave banks. A relationship between the mean number of pieces and the volume recruited by bank erosion (r² = 0·97) indicated a spatial relationship between areas of wood production and storage. Wood mass stored and produced and channel sinuosity increased from 1993 to 2004 at three meander bends. Sinuosity was related to wood mass recruited by bank erosion during the previous decade (r² = 0·73) and both of these parameters were correlated to the mean mass of wood/plot (r² = 0·98 and 0·69 respectively), appearing to control wood storage and delivery at the bend scale. This suggests a local origin of wood stored in channel, not input from upstream trapped by preferential sites. The increase in wood since 1950 is a response to floodplain afforestation, to a change from braided to meandering channel pattern in response to regulation, and to recent large floods. We observed temporal stability of supply and depositional sectors over a decade (on a reach scale). Meander bends were major storage sites, trapping wood with concave banks, also delivering wood. These results, and the link between sinuosity and wood frequency, establish geomorphology as a dominant wood storage and recruitment control in large gravel‐bed rivers. Copyright © 2007 John Wiley & Sons, Ltd.