Elastic and thermoelastic properties of synthetic Ca<Subscript>2</Subscript>MgSi<Subscript>2</Subscript>O<Subscript>7</Subscript> (åkermanite) and Ca<Subscript>2</Subscript>ZnSi<Subscript>2</Subscript>O<Subscript>7</Subscript> (hardystonite)

Elastic and thermoelastic constants of large single crystals of Ca₂MgSi₂O₇ and Ca₂ZnSi₂O₇ have been derived from ultrasonic resonance frequencies of plane-parallel plates and their shift upon variation of temperature, respectively. In addition, coefficients of thermal expansion and dielectric constants were determined. Both species possess quite similar properties. As observed in other isotypic magnesium and zinc compounds, the mean elastic stiffness and the deviation from the Cauchy relations are significantly larger in the zinc compound, due to a covalent contribution of the Zn–O bond. Positive thermoelastic constants T₄₄ and T₆₆ in Ca₂MgSi₂O₇ allow temperature-independent ultrasonic generators and oscillators to be manufactured.     

The magnesiowüstite: iron equilibrium and its implications for the activity-composition relations of (Mg,Fe)<Subscript>2</Subscript>SiO<Subscript>4</Subscript> olivine solid solutions

The chemical potential of oxygen (µO₂) in equilibrium with magnesiowüstite solid solution (Mg, Fe)O and metallic Fe has been determined by gas-mixing experiments at 1,473 K supplemented by solid-cell EMF experiments at lower temperatures. The results give:

Attikaite,Ca<Subscript>3</Subscript>Cu<Subscript>2</Subscript>Al<Subscript>2</Subscript>(AsO<Subscript>4</Subscript>)<Subscript>4</Subscript>(OH)<Subscript>4</Subscript> · 2H<Subscript>2</Subscript>O,a new mineral species

Attikaite, a new mineral species, has been found together with arsenocrandalite, arsenogoyazite, conichalcite, olivenite, philipsbornite, azurite, malachite, carminite, beudantite, goethite, quartz, and allophane at the Christina Mine No. 132, Kamareza, Lavrion District, Attiki Prefecture (Attika), Greece. The mineral is named after the type locality. It forms spheroidal segregations (up to 0.3 mm in diameter) consisting of thin flexible crystals up to 3 × 20 × 80 μm in size. Its color is light blue to greenish blue, with a pale blue streak. The Mohs’ hardness is 2 to 2.5. The cleavage is eminent mica-like parallel to {001}. The density is 3.2(2) g/cm³ (measured in heavy liquids) and 3.356 g/cm³ (calculated). The wave numbers of the absorption bands in the infrared spectrum of attikaite are (cm^?1; sh is shoulder; w is a weak band): 3525sh, 3425, 3180, 1642, 1120w, 1070w, 1035w, 900sh, 874, 833, 820, 690w, 645w, 600sh, 555, 486, 458, and 397. Attikaite is optically biaxial, negative, α = 1.642(2), β = γ = 1.644(2) (X = c) 2V _means = 10(8)°, and 2V _calc = 0°. The new mineral is microscopically colorless and nonpleochroic. The chemical composition (electron microprobe, average over 4 point analyses, wt %) is: 0.17 MgO, 17.48 CaO, 0.12 FeO, 16.28 CuO, 10.61 Al₂O₃, 0.89 P₂O₅, 45.45 As₂O₅, 1.39 SO₃, and H₂O (by difference) 7.61, where the total is 100.00. The empirical formula calculated on the basis of (O,OH,H₂O)₂₂ is: Ca_2.94Cu _1.93 ²⁺ Al_1.97Mg_0.04Fe _0.02 ²⁺ [(As_3.74S_0.16P_0.12)_Σ4.02O_16.08](OH)_3.87 · 2.05H₂ O. The simplified formula is Ca₃Cu₂Al₂(AsO₄)₄(OH)₄ · 2H₂O. Attikaite is orthorhombic, space group Pban, Pbam or Pba2; the unit-cell dimensions are a = 10.01(1), b = 8.199(5), c = 22.78(1) Å, V = 1870(3) ų, and Z = 4. In the result of the ignition of attikaite for 30 to 35 min at 128–140°, the H₂O bands in the IR spectrum disappear, while the OH-group band is not modified; the weight loss is 4.3%, which approximately corresponds to two H₂O molecules per formula; and parameter c decreases from 22.78 to 18.77 Å. The strongest reflections in the X-ray powder diffraction pattern [d, Å (I, %)((hkl)] are: 22.8(100)(001), 11.36(60)(002), 5.01(90)(200), 3.38(5)(123, 205), 2.780(70)(026), 2.682(30)(126), 2.503(50)(400), 2.292(20)(404). The type material of attikaite is deposited in the Fersman Mineralogical Museum, Russian Academy of Sciences, Moscow. The registration number is 3435/1.     

Crystal structure and refined formula of garyansellite Mg<Subscript>2</Subscript>Fe<Superscript>3+</Superscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>(OH) · 2H<Subscript>2</Subscript>O

Single-crystal study of the structure (R = 0.0268) was performed for garyansellite from Rapid Creek, Yukon, Canada. The mineral is orthorhombic, Pbna, a = 9.44738(18), b = 9.85976(19), c = 8.14154(18) Å, V = 758.38(3) ų, Z = 4. An idealized formula of garyansellite is Mg₂Fe³⁺(PO₄)₂(OH) · 2H₂O. Structurally the mineral is close to other members of the phosphoferrite–reddingite group. The structure contains layers of chains of M(2)O₄(OH)(H₂O) octahedra which share edges to form dimers and connected by common edges with isolated from each other M(1)O₄(H₂O)₂ octahedra. The neighboring chains are connected to the layer through the common vertices of M(2) octahedra and octaahedral layers are linked through PO₄ tetrahedra.     

Spectroscopic studies of synthetic and natural ringwoodite, γ-(Mg,Fe)<Subscript>2</Subscript>SiO<Subscript>4</Subscript>

Synthetic ringwoodite γ-(Mg_1?x Fe _x )₂SiO₄ of 0.4 ≤ x ≤ 1.0 compositions and variously colored micro-grains of natural ringwoodite in shock metamorphism veins of thin sections of two S6-type chondrites were studied by means of microprobe analysis, TEM and optical absorption spectroscopy. Three synthetic samples were studied in addition with Mössbauer spectroscopy. The Mössbauer spectra consist of two doublets caused by ^VIFe²⁺ and ^VIFe³⁺, with IS and QS parameters close to those established elsewhere (e.g., O’Neill et al. in Am Mineral 78:456–460, 1993). The Fe³⁺/Fe_total ratio evaluated by curve resolution of the spectra, ranges from 0.04 to 0.1. Optical absorption spectra of all synthetic samples studied are qualitatively very similar as they are directly related to the iron content. They differ mostly in the intensity of the observed absorption features. The spectra consist of a very strong high-energy absorption edge and a series of absorption bands of different width and intensity. The three strongest and broadest absorptions of them are attributed to splitting of electronic spin-allowed ⁵ T _2g → ⁵ E _g transitions of ^VIFe²⁺ and intervalence charge-transfer (IVCT) transition between ferrous and ferric ions in adjacent octahedral sites of the ringwoodite structure. The spin-allowed bands at ca. 8,000 and 11,500 cm^?1 weakly depend on temperature, whilst the Fe²⁺/Fe³⁺ IVCT band at ~16,400 cm^?1 displays very strong temperature dependence: i.e., with increasing temperature it decreases and practically disappears at about 497 K, a behavior typical for bands of this type. With increasing pressure the absorption edge shifts to lower energies while the spin-allowed bands shift to higher energy and strongly decreases in intensity. The IVCT band also strongly weakens and vanishes at about 9 GPa. We assigned this effect to pressure-induced reduction of Fe³⁺ in ringwoodite. By analogy with synthetic samples three broad bands in spectra of natural (meteoritic) blue ringwoodite are assigned to electronic spin-allowed transitions of ^VIFe²⁺ (the bands at ~8,600 and ~12,700 cm^?1) and Fe²⁺/Fe³⁺ IVCT transition (~18,100 cm^?1), respectively. Spectra of colorless ringwoodite of the same composition consist of a single broad band at ca. 12,000 cm^?1. It is assumed that such ringwoodite grains are inverse (Fe, Mg)₂SiO₄-spinels and that the single band is caused by the split spin-allowed ⁵ E → ⁵ T ₂ transition of ^IVFe²⁺. Ringwoodite of intermediate color variations between dark-blue and colorless are assumed to be partly inversed ringwoodite. No glassy material between the grain boundaries in the natural colored ringwoodite aggregates was found in our samples and disprove the cause of the coloration to be due to light scattering effect (Lingemann and Stöffler in Lunar Planet Sci 29(1308), 1998).     

Structural characterization of high-pressure C–Na<Subscript>2</Subscript>Si<Subscript>2</Subscript>O<Subscript>5</Subscript> by single-crystal diffraction and <Superscript>29</Superscript>Si MAS NMR

Single crystals of C–Na₂Si₂O₅ have been synthesized from the hydrothermal recrystallization of a glass. The title compound is monoclinic, space group P2₁/c with Z= 8 and unit-cell parameters a= 4.8521 (4)Å, b=23.9793(16)Å, c=8.1410(6)Å, β=90.15(1)° and V=947.2(2)ų. The structure has been determined by direct methods and belongs to the group of phyllosilicates. It is based on layers of tetrahedra with elliptically six-membered rings in chair conformation. The sequence of directedness within a single ring is UDUDUD. The sheets are parallel to (010) with linking sodium cations in five- and sixfold coordination. Concerning the shape and the conformation of the rings, C–Na₂Si₂O₅ is closely related to β-Na₂Si₂O₅. However, both structures differ in the stacking sequences of the layers. A possible explanation for the frequently observed polysynthetic twinning of phase C is presented. In the ²⁹Si MAS-NMR spectrum of C–Na₂Si₂O₅ four well-resolved lines of equal intensity are observed at ?86.0, ?86.3, ?87.4, and ?88.2?ppm. The narrow range of isotropic chemical shifts reflects the great similarity of the environments of the different Si sites. This lack of pronounced differences in geometry renders a reliable assignment of the resonance lines to the individual sites on the basis of known empiric correlations and geometrical features impossible.     

Mangazeite,Al<Subscript>2</Subscript>(SO<Subscript>4</Subscript>)(OH)<Subscript>4</Subscript> · 3H<Subscript>2</Subscript>O,a new mineral species

Mangazeite, a new mineral species, has been found at the Mangazeya silver deposit (300 km east of the Lena River, 65°43′40″ N and 130°20′ E) in eastern Yakutia (Sakha Republic, Siberia, Russia). The new mineral was described from fractured, sericitized, and pyritized granodiorite adjacent to a quartz-arsenopyrite vein. Associated minerals are gypsum and chlorite. The new mineral occurs as radial fibrous segregations of thin lamellar crystals. The size of the fibers does not exceed 40 μm in length and 1 μm across. The mineral is white, with a white streak and a vitreous luster. Mangazeite is transparent in isolated grains. No fluorescence is observed. The Mohs hardness is 1–2. The calculated density is 2.15 g/cm³. The new mineral is biaxial; its optical character was not determined; α = 1.525(9), β was not measured, and γ = 1.545(9). The average chemical composition is as follows (wt %): Al₂O₃ 36.28, SO₃ 28.81, H₂O⁺ 34.35, total 99.44, H₂O^? 9.27. The H₂O^? content was neither included in the total nor used in formula calculation. The empirical formula is Al_1.99(SO₄)_1.01(OH)_3.94 · 3.37H₂O. The simplified formula is Al₂(SO₄)(OH)₄ · 3H₂O. The theoretical chemical composition calculated from this formula is (wt %) Al₂O₃ 37.47, SO₃ 29.42, H₂O 33.11, total 100.00. The new mineral is triclinic; the unit cell parameters refined from X-ray powder diffraction data are a = 8.286(5), b = 9.385(5), c = 11.35(1) Å, α = 96.1(1), β = 98.9(1), γ = 96.6(1)°, and Z = 4. The strongest lines in the X-ray powder diffraction pattern (d(I, %)) are 8.14(19), 7.59(49), 7.16(46), 4.258(100), 4.060(48), and 3.912(43). Mangazeite is supergene in origin and crystallized in a favorable aluminosilicate environment in the presence of sulfate ion due to pyrite oxidation.     

Static compression of α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>: linear incompressibility of lattice parameters and high-pressure transformations

The high-pressure behavior of -Fe₂O₃ has been studied under static compression up to 60 GPa, using a laser-heated diamond anvil cell. Synchrotron-based angular-dispersive X-ray diffraction shows that the sample remains in the corundum structure up to 50 GPa, but with the appearance of coexisting diffraction lines from a high-pressure phase at pressures above 45 GPa. A least-squares fit of low-pressure phase data to an Eulerian finite-strain equation of state yields linear incompressibilities of K _{a 0}=749.5 (± 18.4) GPa and K _{c 0}= 455.7 (± 21.4) GPa, differing by a factor of 1.6 along the two directions. The enhanced compressibility of the c axis may lead to breaking of vertex- or edge-sharing bonds between octahedra, inducing the high-pressure phase transformation at 50 GPa. Analysis of linear compressibilities suggests that the high-pressure phase above 50 GPa is of the Rh₂O₃ (II) structure. Continuous laser heating reveals a new structural phase transformation of -Fe₂O₃ at 22 GPa, to an orthorhombic structure with a=7.305(3) Å, b=7.850(3) Å, and c=12.877(14) Å, different from the Rh₂O₃ (II) structure.     

Nickeltalmessite,Ca<Subscript>2</Subscript>Ni(AsO<Subscript>4</Subscript>)<Subscript>2</Subscript> · 2H<Subscript>2</Subscript>O,a new mineral species of the fairfieldite group,Bou Azzer,Morocco

Nickeltalmessite, Ca₂Ni(AsO₄)₂ · 2H₂O, a new mineral species of the fairfieldite group, has been found in association with annabergite, nickelaustinite, pecoraite, calcite, and a mineral of the chromite-manganochromite series from the dump of the Aït Ahmane Mine, Bou Azzer ore district, Morocco. The new mineral occurs as spheroidal aggregates consisting of split crystals up to 10 × 10 × 20 μm in size. Nickeltalmessite is apple green, with white streak and vitreous luster. The density measured by the volumetric method is 3.72(3) g/cm³; calculated density is 3.74 g/cm³. The new mineral is colorless under a microscope, biaxial, positive: α = 1.715(3), β = 1.720(5), γ = 1.753(3), 2V _meas = 80(10)°, 2V _calc = 60.4. Dispersion is not observed. The infrared spectrum is given. As a result of heating of the mineral in vacuum from 24° up to 500°C, weight loss was 8.03 wt %. The chemical composition (electron microprobe, wt %) is as follows: 25.92 CaO, 1.23 MgO, 1.08 CoO, 13.01 NiO, 52.09 As₂O₅; 7.8 H₂O (determined by the Penfield method); the total is 101.13. The empirical formula calculated on the basis of two AsO₄ groups is Ca_2.04(Ni_0.77Mg_0.13Co_0.06)_Σ0.96 (AsO₄)_2.00 · 1.91H₂O. The strongest reflections in the X-ray powder diffraction pattern [d, Å (I, %) (hkl)] are: 5.05 (27) (001) (100), 3.57 (43) (011), 3.358 (58) (110), 3.202 (100) (020), 3.099 (64) (0\(\bar 2\)1), 2.813 (60), (\(\bar 1\)21), 2.772 (68) (2\(\bar 1\)0), 1.714 (39) (\(\bar 3\)31). The unit-cell dimensions of the triclinic lattice (space group P1 or P) determined from the X-ray powder data are: a = 5.858(7), b = 7.082(12), c = 5.567(6) Å, α = 97.20(4), β = 109.11(5), γ = 109.78(5)°, V = 198.04 ų, Z = 1. The mineral name emphasizes its chemical composition as a Ni-dominant analogue of talmessite. The type material of nickeltalmessite is deposited at the Fersman Mineralogical Museum, Russian Academy of Sciences, Moscow, Russia, registration number 3750/1.     

Avdoninite: New data,crystal structure and refined formula K<Subscript>2</Subscript>Cu<Subscript>5</Subscript>Cl<Subscript>8</Subscript>(OH)<Subscript>4</Subscript> · 2H<Subscript>2</Subscript>O

The paper reports new findings of avdoninite from deposits of active fumaroles in the Second Scoria Cone at the Northern Breach of the Great Fissure Tolbachik Eruption, Tolbachik Volcano, Kamchatka Peninsula, Russia. The crystal structure of the mineral has been determined for the first time, which has allowed reliable determination of its space group and unit cell dimensions, refinement of its formula K₂Cu₅-Cl₈(OH)₄ · 2H₂O, and correct indexing of its X-ray powder diffraction pattern. Avdoninite is monoclinic, space group P2₁/c, a = 11.592(2), b = 6.5509(11), c = 11.745(2) Å, β = 91.104(6)°, V = 891.8(3) ų, Z = 2. The crystal structure of this mineral has been determined on a single crystal R ₁ [F > 4σ (F)] = 0.063. It is based on sheets of copper–oxo-chloride complexes [Cu₅Cl₈(OH)₄]^2– parallel to (100). The K⁺ cation and H₂O molecules are interlayers.     

Behaviour of Fe<Subscript>4</Subscript>O<Subscript>5</Subscript>–Mg<Subscript>2</Subscript>Fe<Subscript>2</Subscript>O<Subscript>5</Subscript> solid solutions and their relation to coexisting Mg–Fe silicates and oxide phases

Experiments at high pressures and temperatures were carried out (1) to investigate the crystal-chemical behaviour of Fe₄O₅–Mg₂Fe₂O₅ solid solutions and (2) to explore the phase relations involving (Mg,Fe)₂Fe₂O₅ (denoted as O₅-phase) and Mg–Fe silicates. Multi-anvil experiments were performed at 11–20 GPa and 1100–1600 °C using different starting compositions including two that were Si-bearing. In Si-free experiments the O₅-phase coexists with Fe₂O₃, hp-(Mg,Fe)Fe₂O₄, (Mg,Fe)₃Fe₄O₉ or an unquenchable phase of different stoichiometry. Si-bearing experiments yielded phase assemblages consisting of the O₅-phase together with olivine, wadsleyite or ringwoodite, majoritic garnet or Fe³⁺-bearing phase B. However, (Mg,Fe)₂Fe₂O₅ does not incorporate Si. Electron microprobe analyses revealed that phase B incorporates significant amounts of Fe²⁺ and Fe³⁺ (at least ~?1.0 cations Fe per formula unit). Fe-L_2,3-edge energy-loss near-edge structure spectra confirm the presence of ferric iron [Fe³⁺/Fe_tot?=?~?0.41(4)] and indicate substitution according to the following charge-balanced exchange: [4]Si⁴⁺?+?[6]Mg²⁺?=?2Fe³⁺. The ability to accommodate Fe²⁺ and Fe³⁺ makes this potential “water-storing” mineral interesting since such substitutions should enlarge its stability field. The thermodynamic properties of Mg₂Fe₂O₅ have been refined, yielding H°_1bar,298?=???1981.5 kJ mol^??1. Solid solution is complete across the Fe₄O₅–Mg₂Fe₂O₅ binary. Molar volume decreases essentially linearly with increasing Mg content, consistent with ideal mixing behaviour. The partitioning of Mg and Fe²⁺ with silicates indicates that (Mg,Fe)₂Fe₂O₅ has a strong preference for Fe²⁺. Modelling of partitioning with olivine is consistent with the O₅-phase exhibiting ideal mixing behaviour. Mg–Fe²⁺ partitioning between (Mg,Fe)₂Fe₂O₅ and ringwoodite or wadsleyite is influenced by the presence of Fe³⁺ and OH incorporation in the silicate phases.     

Electrical conductivity of polycrystalline Mg(OH)<Subscript>2</Subscript> at 2 GPa: effect of grain boundary hydration–dehydration

The effect of intergranular water on the conductivity of polycrystalline brucite, Mg(OH)₂, was investigated using impedance spectroscopy at 2 GPa, during consecutive heating–cooling cycles in the 298–980 K range. The grain boundary hydration levels tested here span water activities from around unity (wet conditions) down to 10⁻⁴ (dry conditions) depending on temperature. Four orders of magnitude in water activity result in electrical conductivity variations for about 6–7 orders of magnitude at 2 GPa and room temperature. Wet brucite samples containing, initially, about 18 wt% of evaporable water (i.e. totally removed at temperatures below 393 K in air), display electrical conductivity values above 10⁻²–10⁻³ S/m. A.C. electrical conductivity as a function of temperature follows an Arrhenius behaviour with an activation energy of 0.11 eV. The electrical conductivity of the same polycrystalline brucite material dried beforehand at 393 K (dry conditions) is lower by about 5–6 orders of magnitude at room temperature and possesses an activation energy of 0.8–0.9 eV which is close to that of protonic diffusion in (001) brucitic planes. Above ca. 873 K, a non-reversible conductivity jump is observed which is interpreted as a water transfer from mineral bulk to grain boundaries (i.e. partial dehydration). Cooling of such partially dehydrated sample shows electrical conductivities much higher than those of the initially dry sample by 4 orders of magnitude at 500 K. Furthermore, the corresponding activation energy is decreased by a factor of about four (i.e. 0.21 eV). Buffering of the sample at low water activity has been achieved by adding CaO or MgO, two hygroscopic compounds, to the starting material. Then, sample conductivities reached the lowest values encountered in this study with the activation energy of 1.1 eV. The strong dependency of the electrical conductivity with water activity highlights the importance of the latter parameter as a controlling factor of diffusion rates in natural processes where water availability and activity may vary grandly. Water exchange between mineral bulk and mineral boundary suggests that grain boundary can be treated as an independent phase in dehydroxylation reactions.     

Middendorfite,K<Subscript>3</Subscript>Na<Subscript>2</Subscript>Mn<Subscript>5</Subscript>Si<Subscript>12</Subscript>(O,OH)<Subscript>36</Subscript> · 2H<Subscript>2</Subscript>O,a new mineral species from the Khibiny pluton,Kola Peninsula

Middendorfite, a new mineral species, has been found in a hydrothermal assemblage in Hilairite hyperperalkaline pegmatite at the Kirovsky Mine, Mount Kukisvumchorr apatite deposit, Khibiny alkaline pluton, Kola Peninsula, Russia. Microcline, sodalite, cancrisilite, aegirine, calcite, natrolite, fluorite, narsarsukite, labuntsovite-Mn, mangan-neptunite, and donnayite are associated minerals. Middendorfite occurs as rhombshaped lamellar and tabular crystals up to 0.1 × 0.2 × 0.4 mm in size, which are combined in worm-and fanlike segregations up to 1 mm in size. The color is dark to bright orange, with a yellowish streak and vitreous luster. The mineral is transparent. The cleavage (001) is perfect, micalike; the fracture is scaly; flakes are flexible but not elastic. The Mohs hardness is 3 to 3.5. Density is 2.60 g/cm³ (meas.) and 2.65 g/cm³ (calc.). Middendorfite is biaxial (?), α = 1.534, β = 1.562, and γ = 1.563; 2V (meas.) = 10°. The mineral is pleochroic strongly from yellowish to colorless on X through brown on Y and to deep brown on Z. Optical orientation: X = c. The chemical composition (electron microprobe, H₂O determined with Penfield method) is as follows (wt %): 4.55 Na₂O, 10.16 K₂O, 0.11 CaO, 0.18 MgO, 24.88 MnO, 0.68 FeO, 0.15 ZnO, 0.20 Al₂O₃, 50.87 SiO₂, 0.17 TiO₂, 0.23 F, 7.73 H₂O; ?O=F₂?0.10, total is 99.81. The empirical formula calculated on the basis of (Si,Al)₁₂(O,OH,F)₃₆ is K_3.04(Na_2.07Ca_0.03)_Σ2.10(Mn_4.95Fe_0.13Mg_0.06Ti_0.03Zn_0.03)_Σ5.20(Si_11.94Al_0.06)_Σ12O_27.57(OH)_8.26F_0.17 · 1.92H₂O. The simplified formula is K₃Na₂Mn₅Si₁₂(O,OH)₃₆ · 2H₂O. Middenforite is monoclinic, space group: P2₁/m or P2₁. The unit cell dimensions are a = 12.55, b = 5.721, c = 26.86 Å; β = 114.04°, V = 1761 ų, Z = 2. The strongest lines in the X-ray powder pattern [d, Å, (I)(hkl)] are: 12.28(100)(002), 4.31(81)(11\(\overline 4 \)), 3.555(62)(301, 212), 3.063(52)(008, 31\(\overline 6 \)), 2.840(90)(312, 021, 30\(\overline 9 \)), 2.634(88)(21\(\overline 9 \), 1.0.\(\overline 1 \)0, 12\(\overline 4 \)), 2.366(76)(22\(\overline 6 \), 3.1.\(\overline 1 \)0, 32\(\overline 3 \)), 2.109(54)(42–33, 42–44, 51\(\overline 9 \), 414), 1.669(64)(2.2.\(\overline 1 \)3, 3.2.\(\overline 1 \)3, 62\(\overline 3 \), 6.1.\(\overline 1 \)3), 1.614(56)(5.0.\(\overline 1 \)6, 137, 333, 71\(\overline 1 \)). The infrared spectrum is given. Middendorfite is a phyllosilicate related to bannisterite, parsenttensite, and the minerals of the ganophyllite and stilpnomelane groups. The new mineral is named in memory of A.F. von Middendorff (1815–1894), an outstanding scientist, who carried out the first mineralogical investigations in the Khibiny pluton. The type material of middenforite has been deposited at the Fersman Mineralogical Museum, Russian Academy of Sciences, Moscow.     

Kamarizaite,Fe<Stack><Subscript>3</Subscript><Superscript>3+</Superscript></Stack>(AsO<Subscript>4</Subscript>)<Subscript>2</Subscript>(OH)<Subscript>3</Subscript> · 3H<Subscript>2</Subscript>O,a new mineral species,arsenate analogue of tinticite

Kamarizaite, a new mineral species, has been identified in the dump of the Kamariza Mine, Lavrion mining district, Attica Region, Greece, in association with goethite, scorodite, and jarosite. It was named after type locality. Kamarizaite occurs as fine-grained monomineralic aggregates (up to 3 cm across) composed of platy crystals up to 1 μm in size and submicron kidney-shaped segregations. The new mineral is yellow to beige, with light yellow streak. The Mohs hardness is about 3. No cleavage is observed. The density measured by hydrostatic weighing is 3.16(1) g/cm³, and the calculated density is 3.12 g/cm³. The wavenumbers of absorption bands in the IR spectrum of kamarizaite are (cm^?1; s is strong band, w is weak band): 3552, 3315s, 3115, 1650w, 1620w, 1089, 911s, 888s, 870, 835s, 808s, 614w, 540, 500, 478, 429. According to TG and IR data, complete dehydration and dehydroxylation in vacuum (with a weight loss of 15.3(1)%) occurs in the temperature range 110–420°C. Mössbauer data indicate that all iron in kamarizaite is octahedrally coordinated Fe³⁺. Kamarizaite is optically biaxial, positive: n _min = 1.825, n _max = 1.835, n _mean = 1.83(1) (for a fine-grained aggregate). The chemical composition of kamarizaite (electron microprobe, average of four point analyses) is as follows, wt %: 0.35 CaO, 41.78 Fe₂O₃, 39.89 As₂O₅, 1.49 SO₃, 15.3 H₂O (from TG data); the total is 98.81. The empirical formula calculated on the basis of (AsO₄,SO₄)₂ is Ca_0.03Fe _2.86 ³⁺ (AsO₄)_1.90(SO₄)_0.10(OH)_2.74 · 3.27H₂O. The idealized formula is Fe ₃ ³⁺ (AsO₄)₂(OH)₃ · 3H₂O. Kamarizaite is an arsenate analogue of orthorhombic tinticite, space group Pccm, Pcc2, Pcmm, Pcm2₁, or Pc2m; a = 21.32(1), b = 13.666(6), c =15.80(1) Å, V= 4603.29(5) ų, Z= 16. The strongest reflections of the X-ray powder diffraction pattern [\(\bar d\), Å (I, %) (hkl)] are: 6.61 (37) (112, 120), 5.85 (52) (311), 3.947 (100) (004, 032, 511), 3.396 (37) (133, 431), 3.332 (60) (314), 3.085 (58) (621, 414, 324). The type material of kamarizaite is deposited in the Mineralogical Collection of Technische Universität Bergakademie Freiberg, Germany, inventory number 82199.     

Thermal expansion of hydrated six-coordinate silicon in thaumasite,Ca<Subscript>3</Subscript>Si(OH)<Subscript>6</Subscript>(CO<Subscript>3</Subscript>)(SO<Subscript>4</Subscript>)·12H<Subscript>2</Subscript>O

Thaumasite, Ca₃Si(OH)₆(CO₃)(SO₄)12H₂O, occurs as a low-temperature secondary alteration phase in mafic igneous and metamorphic rocks, and is recognized as a product and indicator of sulfate attack in Portland cement. It is also the only mineral known to contain silicon in six-coordination with hydroxyl (OH)^? that is stable at ambient P–T conditions. Thermal expansion of the various components of this unusual structure has been determined from single-crystal X-ray structure refinements of natural thaumasite at 130 and 298 K. No phase transitions were observed over this temperature range. Cell parameters at room temperature are: a= 11.0538(6) Å, c=10.4111(8) Å and V=1101.67(10) ų, and were measured at intervals of about 50 K between 130 and 298 K, resulting in mean axial and volumetric coefficients of thermal expansion (×10^?5K^?1); α _a =1.7(1), α _c =2.1(2), and α _V =5.6(2). Although the unit cell and ^VIIICaO₈ polyhedra show significant positive thermal expansion over this temperature range, the silicate octahedron, sulfate tetrahedron, and carbonate group show zero or negative thermal expansion, with α _V (^VISiO₆) = ?0.6 ± 1.1, α _V (^IVSO₄)=?5.8 ± 1.4, and α _R (C–O)= 0.0 ± 1.8 (×10^?5 K^?1). Most of the thermal expansion is accommodated by lengthening of the R(O...O) hydrogen bond distances by on average 5σ, although the hydrogen bonds involving hydroxyl sites on ^VISi expand twice as much as those on molecular water, causing the [Ca₃Si(OH)₆(H₂O)₁₂]⁴⁺ columns to expand in diameter more than they move apart over this temperature range. The average Si–OH bond length of the six-coordinated Si atom 〈R(^VISi–OH)〉 in thaumasite is 1.783(1) Å, being about 0.02 Å (?20σ) shorter than ^VISi–OH in the dense hydrous magnesium silicate, phase D, MgSi₂H₂O₆.     

The high-pressure stability of chlorite and other hydrates in subduction mélanges: experiments in the system Cr<Subscript>2</Subscript>O<Subscript>3</Subscript>–MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>–H<Subscript>2</Subscript>O

The solubility of chromium in chlorite as a function of pressure, temperature, and bulk composition was investigated in the system Cr₂O₃–MgO–Al₂O₃–SiO₂–H₂O, and its effect on phase relations evaluated. Three different compositions with X _Cr = Cr/(Cr + Al) = 0.075, 0.25, and 0.5 respectively, were investigated at 1.5–6.5 GPa, 650–900 °C. Cr-chlorite only occurs in the bulk composition with X _Cr = 0.075; otherwise, spinel and garnet are the major aluminous phases. In the experiments, Cr-chlorite coexists with enstatite up to 3.5 GPa, 800–850 °C, and with forsterite, pyrope, and spinel at higher pressure. At P > 5 GPa other hydrates occur: a Cr-bearing phase-HAPY (Mg_2.2Al_1.5Cr_0.1Si_1.1O₆(OH)₂) is stable in assemblage with pyrope, forsterite, and spinel; Mg-sursassite coexists at 6.0 GPa, 650 °C with forsterite and spinel and a new Cr-bearing phase, named 11.5 Å phase (Mg:Al:Si = 6.3:1.2:2.4) after the first diffraction peak observed in high-resolution X-ray diffraction pattern. Cr affects the stability of chlorite by shifting its breakdown reactions toward higher temperature, but Cr solubility at high pressure is reduced compared with the solubility observed in low-pressure occurrences in hydrothermal environments. Chromium partitions generally according to \(X_{\text{Cr}}^{\text{spinel}}\) ? \(X_{\text{Cr}}^{\text{opx}}\) > \(X_{\text{Cr}}^{\text{chlorite}}\) ≥ \(X_{\text{Cr}}^{\text{HAPY}}\) > \(X_{\text{Cr}}^{\text{garnet}}\). At 5 GPa, 750 °C (bulk with X _Cr = 0.075) equilibrium values are \(X_{\text{Cr}}^{\text{spinel}}\) = 0.27, \(X_{\text{Cr}}^{\text{chlorite}}\) = 0.08, \(X_{\text{Cr}}^{\text{garnet}}\) = 0.05; at 5.4 GPa, 720 °C \(X_{\text{Cr}}^{\text{spinel}}\) = 0.33, \(X_{\text{Cr}}^{\text{HAPY}}\) = 0.06, and \(X_{\text{Cr}}^{\text{garnet}}\) = 0.04; and at 3.5 GPa, 850 °C \(X_{\text{Cr}}^{\text{opx}}\) = 0.12 and \(X_{\text{Cr}}^{\text{chlorite}}\) = 0.07. Results on Cr–Al partitioning between spinel and garnet suggest that at low temperature the spinel- to garnet-peridotite transition has a negative slope of 0.5 GPa/100 °C. The formation of phase-HAPY, in assemblage with garnet and spinel, at pressures above chlorite breakdown, provides a viable mechanism to promote H₂O transport in metasomatized ultramafic mélanges of subduction channels.     

Influence of oxygen fugacity on the solubility of carbon and hydrogen in FeO-Na<Subscript>2</Subscript>O-SiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> melts in equilibrium with liquid iron at 1.5 GPa and 1400°C

Equilibria in the model melt (NaAlSi₃O₈(80) + FeO(20))-C-H₂ system were experimentally studied at ΔlogfO₂(IW) from −2.2 to −5.6, a pressure of 1.5 GPa, and a temperature of 1400°C. The experiments were conducted in a piston-cylinder apparatus using Pt capsules. The low fO₂ values were imposed during the experiments by adding 2, 5, and 7 wt % of finely dispersed SiC to NaAlSi₃O₈(80) + FeO(20) powder. The experimental products were investigated by electron microprobe analysis and Raman spectroscopy. The investigations showed that melting at 1.5 GPa and 1400°C in the stability field of a metallic iron phase produces silicate liquids containing both oxidized and reduced H and C species. Carbon and hydrogen are dissolved in the melt as C-H (CH₄) complexes. In addition, OH⁻ groups, molecular hydrogen H₂, and molecular water H₂O were observed in the melts. The proportions of dissolved C and H species strongly depend on oxygen fugacity. With decreasing fO₂, the content of O-H species decreases and that of H-C species increases. The obtained data and previous results (Kadik et al., 2004, 2006) allow us to suppose a fundamental change in the character of magmatic transfer of C-O-H components during the evolution of the redox state of the Earth’s mantle in geologic time toward higher fO₂ in its interiors.     

High-pressure X-ray diffraction and Raman spectroscopy of CaFe<Subscript>2</Subscript>O<Subscript>4</Subscript>-type β-CaCr<Subscript>2</Subscript>O<Subscript>4</Subscript>

In situ high-pressure synchrotron X-ray diffraction and Raman spectroscopic studies of orthorhombic CaFe₂O₄-type β-CaCr₂O₄ chromite were carried out up to 16.2 and 32.0 GPa at room temperature using multi-anvil apparatus and diamond anvil cell, respectively. No phase transition was observed in this study. Fitting a third-order Birch–Murnaghan equation of state to the P–V data yields a zero-pressure volume of V ₀ = 286.8(1) ų, an isothermal bulk modulus of K ₀ = 183(5) GPa and the first pressure derivative of isothermal bulk modulus K ₀′ = 4.1(8). Analyses of axial compressibilities show anisotropic elasticity for β-CaCr₂O₄ since the a-axis is more compressible than the b- and c-axis. Based on the obtained and previous results, the compressibility of several CaFe₂O₄-type phases was compared. The high-pressure Raman spectra of β-CaCr₂O₄ were analyzed to determine the pressure dependences and mode Grüneisen parameters of Raman-active bands. The thermal Grüneisen parameter of β-CaCr₂O₄ is determined to be 0.93(2), which is smaller than those of CaFe₂O₄-type CaAl₂O₄ and MgAl₂O₄.     

La–SiO<Subscript>2</Subscript> and Yb–SiO<Subscript>2</Subscript> systematics in mid-ocean ridge magmas: implications for the origin of oceanic plagiogranite

Analytical expressions for the variation in D _La and D _Yb with increasing liquid SiO₂ for olivine, plagioclase, augite, hornblende, orthopyroxene, magnetite and ilmenite (Brophy in Contrib Mineral Petrol 2008, online first) have been combined with numerical models of hydrous partial melting, of mid-ocean ridge (MOR) cumulate gabbro melting, and fractional crystallization of slightly hydrous mid-ocean ridge basalt (MORB) magma to assess a melting versus fractionation origin for oceanic plagiogranite. For felsic magmas (>63 wt.% SiO₂) the modeling predicts the following. MOR cumulate gabbro melting should yield constant or decreasing La and constant Yb abundances with increasing liquid SiO₂. The overall abundances should be similar to those in associated mafic magmas. MORB fractional crystallization should yield steadily increasing La and Yb abundances with increasing SiO₂ with overall abundances significantly higher than those in associated mafic magmas. Application to natural occurrences of oceanic plagiogranite indicate that both MOR cumulate gabbro melting and MORB fractionation are responsible. Application of the model results to Icelandic rhyolites strongly support a fractional crystallization rather than a crustal melting origin.     

Heat capacity of hydrous trachybasalt from Mt Etna: comparison with CaAl<Subscript>2</Subscript>Si<Subscript>2</Subscript>O<Subscript>8</Subscript> (An)–CaMgSi<Subscript>2</Subscript>O<Subscript>6</Subscript> (Di) as basaltic proxy compositions

The specific heat capacity (C _p) of six variably hydrated (~3.5 wt% H₂O) iron-bearing Etna trachybasaltic glasses and liquids has been measured using differential scanning calorimetry from room temperature across the glass transition region. These data are compared to heat capacity measurements on thirteen melt compositions in the iron-free anorthite (An)–diopside (Di) system over a similar range of H₂O contents. These data extend considerably the published C _p measurements for hydrous melts and glasses. The results for the Etna trachybasalts show nonlinear variations in, both, the heat capacity of the glass at the onset of the glass transition (i.e., C _p ^g ) and the fully relaxed liquid (i.e., C _p ^l ) with increasing H₂O content. Similarly, the “configurational heat capacity” (i.e., C _p ^c  = C _p ^l  ? C _p ^g ) varies nonlinearly with H₂O content. The An–Di hydrous compositions investigated show similar trends, with C _p values varying as a function of melt composition and H₂O content. The results show that values in hydrous C _p ^g , C _p ^l and C _p ^c in the depolymerized glasses and liquids are substantially different from those observed for more polymerized hydrous albitic, leucogranitic, trachytic and phonolitic multicomponent compositions previously investigated. Polymerized melts have lower C _p ^l and C _p ^c and higher C _p ^g with respect to more depolymerized compositions. The covariation between C _p values and the degree of polymerization in glasses and melts is well described in terms of SM_hydrous and NBO/T _hydrous. Values of C _p ^c increase sharply with increasing depolymerization up to SM_hydrous ~ 30–35 mol% (NBO/T _hydrous ~ 0.5) and then stabilize to an almost constant value. The partial molar heat capacity of H₂O for both glasses (\( C_{{{\text{p}}\;{\text{H}}_{2} {\text{O}}}}^{\text{g}} \)) and liquids (\( C_{{{\text{p}}\;{\text{H}}_{2} {\text{O}}}}^{\text{l}} \)) appears to be independent of composition and, assuming ideal mixing, we obtain a value for \( C_{{{\text{p}}\;{\text{H}}_{2} {\text{O}}}}^{\text{l}} \) of 79 J mol^?1 K^?1. However, we note that a range of values for \( C_{{{\text{p}}\;{\text{H}}_{2} {\text{O}}}}^{\text{l}} \) (i.e., ~78–87 J mol^?1 K^?1) proposed by previous workers will reproduce the extended data to within experimental uncertainty. Our analysis suggests that more data are required in order to ascribe a compositional dependence (i.e., nonideal mixing) to \( C_{{{\text{p}}\;{\text{H}}_{2} {\text{O}}}}^{\text{l}} \).