Flow induced vibrations of a sharp edge square cylinder in the wake of a circular cylinder

The response of an oscillating circular cylinder at the wake of an upstream fixed circular cylinder was classified by different researchers as galloping, wake induced galloping or wake induced vibration. Furthermore it is already known that a sharp edge square cylinder would undergo galloping if it is subjected to uniform flow. In this study the influence of the wake of a fixed circular cylinder on the response of a downstream square cylinder at different spacing ratios (S/D = 4, 8, 11) is experimentally investigated. The subject appears not to have received previous attention. The lateral displacements, lift forces and the pressure data from gauges mounted in the wake of the oscillating cylinder are recorded and analyzed. The single degree of freedom vibrating system has a low mass-damping parameter and the Reynolds number ranges from 7.7 × 10² to 3.7 × 10⁴.In contrast to that for two circular cylinders in tandem arrangement, the freely mounted downstream square cylinder displays a VIV type of response at all spacing ratios tested. There is no sign of galloping or wake induced galloping with the square cylinder. With increase at the spacing ratio the cross-flow oscillations decrease. It is shown that the vortices arriving from the upstream fixed circular cylinder play a major role on the shedding mechanism behind the downstream square cylinder and cause the square cylinder to shed vortices with frequencies above Strouhal frequency of the fixed square cylinder (St = 0.13). The VIV type of oscillations in the downstream square cylinder is most probably caused by the vortices newly generated behind the square cylinder.     

Three-dimensional flow around a square cylinder near a wall

In this study, two- and three-dimensional numerical simulations were performed to investigate the effect of the flow structure in the wake of a square cylinder placed near a plane wall by applying a fully implicit finite-difference method to the Navier-Stokes equations. The gap ratio between the cylinder and the wall, G/D, was varied from 0.2 to 4 for the Reynolds numbers of 175, 185 and 250. The role of the 3D structure on the lift and drag coefficients and Strouhal number was investigated. The results were compared with those of the 2D numerical simulations. The deviations of the 3D flow structure of the cylinder-wall pair from that of a single cylinder were also reported. At Re=250, B type secondary vortices were determined in the wake region. At Re=175 and 185, transition from A type vortex to fully periodic B type vortices was observed when the cylinder was brought closer to the wall.     

The effect of shroud on vortex shedding mechanism of cylinder

In the present study, flow characteristics were investigated experimentally using particle image velocimetry technique (PIV) in a gap between a solid cylinder and a shroud to reveal the effect of shroud diameter (D_s) and porosity (β) on the vortex shedding mechanism of the cylinder. Porosity (varied from β = 0.3 to 0.7) and diameter ratio (D/D_s = 0.4, 0.5 and 0.6) were main parameters examined at a Reynolds number of Re = 5000. For the porosity values of β ≤ 0.5, it is observed that vortex formation of the cylinder occurs only in the gap and shroud produces its own wake flow patterns. Penetrating flow through the shroud extends the shear layers on the both sides of the shroud through the downstream direction and prevents the interaction of shear layers in the near wake region. The diameter ratio and the porosity are impactful on the wake flow patterns in outer region of the shroud since they are determinant of the penetrating flow rate. Force measurements were also performed in the air tunnel in order to reveal the effect of shroud on the drag coefficient of cylinder. It is found that the drag coefficient of the cylinders are reduced significantly by shrouds when compared with that obtained from the bare cylinder case. However, the drag coefficient of the cylinder together with the shroud is higher than the bare cylinder for all cases since the shrouds enlarge the area exposed to the flow.     

Vortex shedding suppression for flow over a circular cylinder near a plane boundary

In this study, the Navier-Stokes equations and the pressure Poisson equation for two-dimensional time-dependent viscous flows are solved with a finite difference method in a curvilinear coordinate system. With this numerical procedure, the vortex shedding flow past a circular cylinder near a wall is investigated. The flow is calculated for a broad range of gap ratios for different Reynolds numbers ranging from 80 to 1000. Based on the numerical solutions, the vortex shedding is observed using various methods, and the mechanism for the vortex shedding suppression at small gap ratios is analyzed. The critical gap ratio at which the vortex shedding is suppressed is identified at different Reynolds numbers.     

Computational study on near wake interaction between undulation body and a D-section cylinder

We present a numerical study on the hydrodynamic performance of undulation NACA0012 foil in the near wake of D-section cylinder. Computations are conducted using unsteady incompressible Navier-Stokes equations with a moving adaptive mesh based on laminar flow. Investigations are focused on the effect of distance ratio between foil tip and centre of cylinder (L/D≤2.0) on the thrust/drag performance of foil and cylinder at various foil undulation frequency (St). We found that, foil thrust coefficient (C_t) increases considerably with the appearance of cylinder and an optimal distance exists at which C_t reaches maxima. The maximum increment is about eleven times that of its counterpart of single foil, which is obtained at St=0.23 and L/D=0.5. Our results for the cylinder drag coefficient (C_d) observed the existence of optimal parametric map, combined with various gap ratios and foil frequencies. With these parameters, insertion of an undulation foil can significantly lead to the drag reduction indicating that undulating foil could work efficiently as a passive vortex control device for cylinder drag reduction.     

五圆柱体结构群绕流特性及互扰效应研究

基于Fluent流体计算平台,运用大涡模拟方法对亚临界雷诺数Re=3900下“X”形排列五圆柱体结构群三维绕流特性进行研究,主要分析来流攻角α与间距比L/D两个关键参数对五圆柱体结构群的尾流区三维涡结构演化与流体力系数的影响,并揭示其内在流动互扰机理。研究表明:来流攻角和间距比的变化对五圆柱体结构群流动控制及互扰效应的影响显著。在小间距比工况下,观察到柱体群间隙区域内流体高速流动的现象,导致五圆柱体之间的互扰作用十分强烈。间隙流对中间圆柱体和下游圆柱体有较强的冲击作用,对其表面的流体力分布特性有显著的影响。另外,大间距比工况下,当α=0°与L/D≥5.0工况时,柱体群尾流效应强于其间隙流效应。当α=22.5°与L/D=7.0时,位于下游与中间处的圆柱体流体绕流特性存在较大差异。而当α=45°与L/D≥6.0时,位于上游与中间处的圆柱体尾流区均会产生正负交替的漩涡结构。     

Numerical Simulation on Flow Past Two Side-by-Side Inclined Circular Cylinders at Low Reynolds Number

A series of three-dimensional numerical simulations is carried out to investigate the effect of inclined angle on flow behavior behind two side-by-side inclined cylinders at low Reynolds number Re=100 and small spacing ratio T/D=1.5 (T is the center-to-center distance between two side-by-side cylinders, D is the diameter of cylinder). The instantaneous and time-averaged flow fields, force coefficients and Strouhal numbers are analyzed. Special attention is focused on the axial flow characteristics with variation of the inclined angle. The results show that the inclined angle has a significant effect on the gap flow behaviors behind two inclined cylinders. The vortex shedding behind two cylinders is suppressed with the increase of the inclined angle as well as the flip-flop gap flow. Moreover, the mean drag coefficient, root-mean-square lift coefficient and Strouhal numbers decrease monotonously with the increase of the inclined angle, which follows the independent principle at small inclined angles.     

不同倒角半径四柱体绕流数值模拟及水动力特性分析

为研究四柱体布置情况下倒角半径变化对柱体绕流水动力特性的影响,使用Fluent软件,采用大涡模拟方法研究了在雷诺数Re=3 900下6种不同倒角半径的柱体在方形四柱体布置时的三维流场。在模型分析验证有效后,分析了柱体后方瞬时流场、水动力参数、时均流场的变化情况。分析结果表明:随着倒角半径的增大,上游柱体的平均阻力系数逐渐减小,下游柱体的平均阻力系数除了在R~+=0.1处增幅很大以外,其余均随倒角半径变大而平稳变大;各柱体的升力系数均方根变化趋势基本相同;R~+=0.1、0.5时,上下游两柱体的升力系数曲线相位相反,而在R~+=0.2、0.3和0.4时,上下游两柱体的升力系数曲线相位相同。     

Stream-wise and cross-flow vortex induced vibrations of single tapered circular cylinders: An experimental study

Tapered circular cylinders are employed in a variety of ocean engineering applications. While being geometrically simple, this configuration creates a complex flow pattern in the near wake of the structure. Most previous experimental studies on tapered circular cylinders were dealing with stationary cylinders to explore the wake flow field and vortex shedding patterns past the cylinder. Few studies paid attentions to the vortex induced vibration of the tapered cylinders. This paper reports some results from in-water towing-tank experiments on the vortex-excited vibrations of tapered circular cylinders in a uniform flow. Cylinders with different mean diameters (28 and 78 mm), mass ratios (6.1 and 2.27) and tapers (5–20), along with their equivalent uniform cylinders, have been examined. The single degree of freedom vibrating system has a low mass-damping parameter (m*ξ = 0.0084–0.0279). The Reynolds number, based on mean diameter of the cylinders, ranges from 1400 to 70,200. The reduced velocities vary from 1.5 to 22. Effects of variations in the taper and mass ratios on the lock-in range, the reduced response amplitude, the reduced velocity for the peak vibration response and other stream-wise and cross-flow VIV parameters are reported and discussed.     

Flow past a circular cylinder between parallel walls at low Reynolds numbers

The flow about a circular cylinder placed centrally inside a channel is studied numerically with an unstructured collocated grid finite volume method based on the primitive variable formulation. The distance between the channel walls is allowed to vary to change the blockage ratio. Simulations are carried out over a range of Reynolds numbers that are consistent with the two-dimensional assumption. The study confirms that transition to vortex shedding regime is delayed when the channel walls are close to the cylinder because of the interaction between the vortices from the channel wall and cylinder wake. In the unsteady vortex shedding regime, the wake pattern is opposite to the classic Karman street in respect of the positions of the shed vortices. The cylinder drag coefficient and Strouhal number are considerably increased at smaller gaps while the root-mean-squared lift coefficient is significantly decreased. Several important flow parameters are correlated with the input parameters, namely Reynolds number and blockage ratio.     

不等直径串列双圆柱体绕流的数值模拟

利用Fluent软件模拟雷诺数为200时不同间距比G/D和直径比d/D情况下的圆柱绕流现象。根据模拟结果分析G/D和d/D对圆柱体的涡脱落形态,大、小柱体的升力,阻力系数和St数的影响,结果表明涡脱落形态随着G/D和d/D的变化呈现不同的形式,在G/D小于临界间距比时呈现单一涡脱落形态,在G/D大于临界间距比时,呈现双旋涡脱落形态;临界间距比随着d/D增大而增大。在临界间距比附近大、小柱体的升力和阻力系数值及St数变化较大,大、小柱体的St数具有相同的变化规律,St随着d/D的增大而减小。     

Numerical investigation on the suppression of VIV for a circular cylinder by three small control rods

Laminar flow past a circular cylinder with 3 small control rods is investigated by numerical simulation. This study is concerned with the suppression efficacy of vortex induced vibration by small control rods located around a main cylinder. The effects of the attack angle and rod-to-cylinder gap ratio on the hydrodynamics and vibration responses of the main cylinder are investigated. The attack angle of α = 45° is performed as the critical angle for VIV suppression of 3 control rods. The 3 control rods have no effect on VIV suppression when the attack angle is less than the critical angle. The 3 control rods have an excellent VIV suppression efficacy when the attack angle is larger than the critical angle. The transverse vibration frequency of the cylinder with 3 control rods is less than that for an isolated cylinder for all the configurations. The numerical results for the configurations of α = 45° & 60°, G/D = 0.6–1.2 show excellent suppression efficient among the cases investigated in this study. The best suppression efficient is found at α = 45°, G/D = 0.9 for 3 control rods. 2 rods in behind of the main cylinder perform more efficient than that of 1 rod in front for VIV suppression as the gap ratio of G/D less than 1.0.     

不同雷诺数下倾斜圆柱绕流三维数值模拟研究

基于计算流体力学(CFD)开源代码OpenFOAM开展了不同雷诺数(Re=100、1500和3900)和倾斜角度(-60°≤α≤60°)工况下倾斜圆柱绕流流场的三维数值模拟,研究倾斜圆柱绕流的三维瞬时及时均尾流流场、流线拓扑、升阻力系数与旋涡脱落频率随雷诺数及倾斜角度变化的规律,探讨在顺流向及逆流向情况下独立性原则对倾斜圆柱绕流的适用性。研究结果表明:随着圆柱倾角的增大,倾斜圆柱尾流产生较为明显的轴向流,尾流旋涡脱落受到明显抑制,细碎旋涡逐渐消失,尾流宽度随之减小;随着雷诺数的增大,圆柱尾流涡管发生明显的变形,展向掺混使得大量细碎旋涡产生,呈现出明显的三维特性。在不同雷诺数下,阻力系数均值、升力系数均方根及无量纲涡脱频率在一定倾角范围内符合独立性原则。     

张力腿平台绕流数值模拟分析

在一定来流条件下,张力腿平台(tension leg platform,简称TLP)的立柱后缘出现周期性的交替旋涡脱落,致使立柱受到垂直于来流方向的升力和平行于来流方向的阻力作用,导致TLP产生大幅度往复运动,显著增加平台结构和系泊系统的负载。目前,关于单柱、多柱结构绕流问题的研究较多,但对于TLP绕流特性的研究较少,机理尚存不明确的地方。为研究TLP的绕流力变化情况和流场特征,开展了数值模拟分析。利用计算流体动力学数值模拟软件,基于雷诺平均(RANS)法和分离涡模拟(DES)法对TLP绕流场进行仿真分析,揭示了TLP的绕流特性。结果表明,在3种来流角度和多个折合速度V_r下,TLP绕流的流体力系数存在明显差异,升力系数时域曲线呈现脉动性。TLP的上、下游立柱间存在明显的相互作用,影响了旋涡的形成与发展。TLP的旋涡脱落大多集中在平台固有频率附近,且在V_r=7,来流角度为0°时,升力系数频谱峰值最大,旋涡脱落集中。     

On a translating and transversely oscillating cylinder: Part 2: Effect of the velocity ratio on the hydrodynamic forces and the near-wake structure

The unsteady flow past a circular cylinder which starts translating and transversely oscillating from rest in a viscous fluid is investigated at a Reynolds numbers of R=10³ and at a Strouhal number of π/4 and for the maximum oscillatory to translational velocity ratios between 0.1 and 1.0. This study is based on numerical solutions of the two-dimensional unsteady Navier–Stokes equations. The object of the study is to examine the effect of increase of velocity ratio on the near-wake structure as well as the hydrodynamic forces acting on the cylinder. For all velocity rates a periodic structure of vortex evaluation and shedding develops which is repeated exactly as time advances. Vortex dynamics close behind the body are affected by changing acceleration of the cylinder and a changeover from one mode to a different mode of vortex formation is observed with increase in velocity ratio. A comparison of the present results with the impulsively started translating case has been included to illustrate the effect of velocity ratio on drag at small values of velocity ratio.     

Force and flow characteristics of a circular cylinder with uniform surface roughness at subcritical Reynolds numbers

The main purpose of this study is to establish a better understanding of the relationship between drag reduction and surface roughness. Experiments were conducted to measure the force and flow characteristics of a circular cylinder with different types of artificial surface roughness over the range 6 × 10³ < Re < 8 × 10⁴ (Re is based on the cylinder diameter D). The roughness cylinder was formed by covering the exterior surface of the cylinder with uniformly distributed (1) sandpaper, (2) netting, and (3) dimples. The roughness coefficient ranged from k/D = 0.0028 to 0.025 (k is the roughness height). A detailed quantitative measurement of the flow field around the cylinder using Particle Imaging Velocimetry (PIV) was carried out. The hydrodynamic force coefficients (drag and lift) of the rough cylinders are compared against those of a smooth cylinder measured under the same flow conditions. It is found that certain configuration of surface roughness significantly reduces the mean drag coefficient of the cylinder, particularly at large Reynolds numbers. In addition, the root-mean-square (r.m.s.) lift coefficient of the rough cylinders is considerably lower than that of a smooth cylinder.     

Effects of mass and damping ratios on VIV of a circular cylinder

In this study the basic characteristics of the dynamic response and vortex shedding from an elastically mounted circular cylinder in laminar flow is numerically investigated. The Reynolds number ranges from 80 to 160, a regime that is fully laminar. The governing equations of fluid flow are cast in terms of vorticity. The two-dimensional vorticity transport equation is solved using a vortex method. Effects of important parameters on the system response and vortex shedding are investigated; these include: mass ratio, damping ratio, Reynolds number and reduced velocity. The numerical results show that a decrease in either the mass ratio or damping ratio of the system can lead to an increase in both the oscillation amplitude and the reduced velocity range over which lock-in occurs. The results also suggest that the mass-damping parameter may characterize the system response adequately, although the effect of changing mass ratio appears to be a little more profound compared to damping ratio. Vorticity contour plots suggest that the vortex shedding occurs in the 2S mode, although a wake structure similar to the C(2S) mode appears at distances 15–20 diameters downstream in the lock-in region. The simulation results are in good agreement with previously published data.     

两层粘性流体中圆柱体受迫振荡数值模拟

研究两层粘性流体中无限长水平圆柱体的受迫振荡问题。在湍流模式下,采用VOF方法追踪两层流体的内界面,基于动网格技术模拟圆柱体的运动边界,对均匀流中横向振荡圆柱体的绕流场进行了数值模拟。计算受迫振荡圆柱体的升力系数、阻力系数随时间的演化曲线和圆柱体的尾涡分布,以及圆柱体的受迫振荡激发两层流体内界面的扰动,并与均匀流体的情况进行了比较分析。研究表明,流体的两层分层效应对受迫振荡圆柱体的升阻力系数和尾涡分布特性都有显著影响,在水下输油气管道涡激振动特性的工程评估中,应考虑流体的密度分层效应。     

亚临界区雷诺数下圆柱绕流场电磁力控制数值研究

在亚临界区雷诺数下,采用脱体涡模拟方法对弱电解质中电磁力作用下圆柱绕流场及其升阻力特性进行了数值模拟与分析。结果表明,电磁力可以提高圆柱体边界层内的流体动能,延缓圆柱体近壁面流动分离,减弱绕流场中流向和展向大尺度涡的强度,减小圆柱体阻力及其升力脉动幅值;当电磁力作用参数大于某个临界值后,流动分离角消失,在圆柱体尾部产生射流现象,电磁力产生净推力作用,出现负阻力现象,而且升力脉动幅值显著减小且接近于零。