Effects of helical flow in one‐dimensional modelling of sediment distribution at river bifurcations

Complex flow processes at river bifurcations and the influence of the layout of a bifurcation make it difficult to predict sediment distribution over the downstream branches in case bedload transport dominates. In one‐dimensional models we need a nodal point relationship that prescribes the distribution of sediment over the downstream branches. We have identified which factors need to be included in such a relationship for the division of bedload transport at bifurcations. Next, irrotational flow theory for idealized geometries has been used to derive a simple physics‐based nodal point relationship that accounts for the effects of helical flow in the situation that a channel takes off under an angle from a straight main channel. This first step towards a complete nodal point relationship is applicable to bedload transport situations if the flow is clearly curved and if there is no pronounced bed topography. The relationship has been tested against data from a unique set of laboratory measurements, numerical data and data from a scale model of the Rhine bifurcation at Pannerden in the Netherlands. We find that the derived model yields a reasonable prediction of the sediment division over the downstream branches, and yields better predictions than the Wang et al. model for the situation considered. Considering the relative complexity and limited accuracy of the nodal point relationship for the effect of helical flow alone, however, we conclude thatderiving a practical physics‐based 1‐D relationship including all relevant processes is not feasible. We therefore recommend 2‐D or 3‐D modelling for all cases in general where morphological evolution depends on the division of bedload transport at bifurcations. Copyright © 2012 John Wiley & Sons, Ltd.     

Evolution of a bifurcation in a meandering river with adjustable channel widths,Rhine delta apex,The Netherlands

Rivers may dramatically change course on a fluvial plain. Such an avulsion temporarily leads to two active channels connected at a bifurcation. Here we study the effect of dynamic meandering at the bifurcation and the effect of channel width adjustment to changing discharge in both downstream branches on the evolution of a bifurcation and coexisting channels. As an example, we reconstructed the last major avulsion at the Rhine delta apex. We combined historical and geological data to reconstruct a slowly developing avulsion process spanning 2000 years and involving channel width adjustment and meandering at the bifurcation. Based on earlier idealised models, we developed a one‐dimensional model for long‐term morphodynamic prediction of upstream channel and bifurcates connected at the bifurcation node. The model predicts flow and sediment partitioning at the node, including the effect of migrating meanders at the bifurcation and channel width adjustment. Bifurcate channel width adaptation to changing discharge partitioning dramatically slows the pacing of bifurcation evolution because the sediment balance for width adjustment and bed evolution are coupled. The model further shows that meandering at the bifurcation modulates channel abandonment or enlargement periodically. This explains hitherto unrecognised reactivation signals in the sedimentary record of the studied bifurcation meander belts, newly identified in our geological reconstruction. Historical maps show that bifurcation migration due to meander bend dynamics increases the bifurcation angle, which increases the rate of closure of one bifurcate. The combination of model and reconstruction identifies the relevant timescales for bifurcation evolution and avulsion duration. These are the time required to fill one downstream channel over one backwater length, the time to translate one meander wavelength downstream and, for strong river banks, the adaptation timescale to adjust channel width. The findings have relevance for all avulsions where channel width can adjust to changing discharge and where meandering occurs. Copyright © 2011 John Wiley & Sons, Ltd.     

Free and forced morphodynamics of river bifurcations

Water and sediment distribution by river bifurcations is often highly unbalanced. This may result from a variety of factors, such as migration of bars, channel curvature and backwater effects, which promote an uneven partition of flow and sediment fluxes in the downstream branches, which we call ‘forcings’. Bifurcations also display an intrinsic instability mechanism that leads to unbalanced configurations, as occurs in the idealized case of a geometrically symmetric bifurcation, which we call ‘free’, provided the width-to-depth ratio of the incoming flow is large enough. Most frequently, these free and forced mechanisms coexist; however, their controlling roles in bifurcation dynamics have not been investigated so far. In this paper we address this question by proposing a unified free-forced modelling framework for bifurcation morphodynamics. Upstream channel curvature and different slopes of downstream branches (slope advantage) are specifically investigated as forcing effects typically occurring in bifurcations of alluvial channels. The modelling strategy is based on the widely used two-cell model of Bolla Pittaluga et al. (Water Resources Research, 2003, 39 (3), 1–13), here extended to account for the spatially non-uniform fluxes entering the bifurcation node. Results reveal that the relative role of free and forced mechanisms depends on the width-to-depth ratio falling above or below the resonant threshold that controls the stability of free bifurcations: when the main channel is relatively wide and shallow (super-resonant regime) the bifurcation invariably evolves towards unbalanced configurations, whatever the combination of curvature and slope advantage values, which instead control the bifurcation response under sub-resonant conditions. Detection of the resonant aspect ratio as a key threshold also releases the modelling approach from the need for parameter calibration that characterized previous approaches, and allows for interpreting under a unified framework the opposite behaviours shown by gravel-bed and sand-bed bifurcations for increasing Shields parameter values. © 2018 John Wiley & Sons, Ltd.     

Flow structures at an idealized bifurcation: a numerical experiment

River bifurcations are key nodes within braided river systems controlling the flow and sediment partitioning and therefore the dynamics of the river braiding process. Recent research has shown that certain geometrical configurations induce instabilities that lead to downstream mid‐channel bar formation and the formation of bifurcations. However, we currently have a poor understanding of the flow division process within bifurcations and the flow dynamics in the downstream bifurcates, both of which are needed to understand bifurcation stability. This paper presents results of a numerical sensitivity experiment undertaken using computational fluid dynamics (CFD) with the purpose of understanding the flow dynamics of a series of idealized bifurcations. A geometric sensitivity analysis is undertaken for a range of channel slopes (0.005 to 0.03), bifurcation angles (22° to 42°) and a restricted set of inflow conditions based upon simulating flow through meander bends with different curvature on the flow field dynamics through the bifurcation. The results demonstrate that the overall slope of the bifurcation affects the velocity of flow through the bifurcation and when slope asymmetry is introduced, the flow structures in the bifurcation are modified. In terms of bifurcation evolution the most important observation appears to be that once slope asymmetry is greater than 0.2 the flow within the steep bifurcate shows potential instability and the potential for alternate channel bar formation. Bifurcation angle also defines the flow structures within the bifurcation with an increase in bifurcation angle increasing the flow velocity down both bifurcates. However, redistributive effects of secondary circulation caused by upstream curvature can very easily counter the effects of local bifurcation characteristics. Copyright © 2011 John Wiley & Sons, Ltd.     

Bar dynamics and bifurcation evolution in a modelled braided sand‐bed river

Morphodynamics in sand‐bed braided rivers are associated with simultaneous evolution of mid‐channel bars and channels on the braidplain. Bifurcations around mid‐channel bars are key elements that divide discharge and sediment. This, in turn, may control the evolution of connected branches, with effects propagating to both upstream and downstream bifurcations. Recent works on bifurcation stability and development hypothesize major roles of secondary flow and gradient advantage. However, this has not been tested for channel networks within a fully developed dynamic braided river. A reason for this is a lack of detailed measurements with sufficient temporal and spatial length, covering multiple bifurcations. Therefore we used a physics‐based numerical model to generate a dataset of bathymetry, flow and sediment transport of an 80 km river reach with self‐formed braid bars and bifurcations. The study shows that bar dissection due to local transverse water surface gradients is the dominant bifurcation initiation mechanism, although conversion of unit bars into compound bars dominates in the initial stage of a braided river. Several bifurcation closure mechanisms are equally important. Furthermore, the study showed that nodal point relations for bifurcations are unable to predict short‐term bifurcation evolution in a braided river. This is explained by occurrence of nonlinear processes and non‐uniformity within the branches, in particular migrating bars and larger‐scale backwater‐effects, which are not included in the nodal point relations. Planform morphology, on the other hand, has predictive capacity: bifurcation angle asymmetry and bar‐tail limb shape are indicators for near‐future bifurcation evolution. Remote sensing data has predictive value, for which we developed a conceptual model for interactions between bars, bifurcations and channels in the network. We conducted a preliminary test of the conceptual model on satellite images of the Brahmaputra. Copyright © 2015 John Wiley & Sons, Ltd.     

River channel adjustments downstream from channelization works in England and Wales

Relatively little attention has been given to river channel adjustments that occur downstream from channelization works. This study is concerned with the nature of channel adjustments downstream from a total of 46 channelization works located in low and high energy environments in England and Wales. Channel changes are identified principally by the method of field survey and by reconstructing the original positions of eroded beds and banks. Use is also made of maps, aerial photographs, and engineering drawings of different dates and the technique of space-for-time substitution is applied. Enlargement of channel cross-sections through erosion had occurred downstream from a variety of types, sizes, and dates of channelization works. The maximum increase of channel size was 153 per cent. Out of a total of 14 sites with enlarged channel cross-sections, seven had undergone a change of width only, at a further three width increased rather than depth, and at the remaining four sites depth increases were dominant. These sites all have relatively high stream powers. Factors causing spatial variation of erosion included tree roots locally binding bank sediments and the occurrence of bends. Planform change had taken place at only one site. A further three high stream power sites had downstream reaches incised into bedrock and therefore did not exhibit adjustment. Channel enlargement is explained in terms of increased flood flows downstream from channelization works causing higher stream velocities, which in turn cause erosion, thereby increasing channel width and/or depth. Examination of flow records for 35 stations revealed flood events which would formerly have spread overbank but are now confined by the channelization works and are therefore likely to alter downstream flows. At sites with downstream change it is proposed that the energy of increased flows was sufficient to exceed a threshold required for erosion of perimeter sediments. By contrast the absence of change at a majority of sites in low energy lowland areas could be a reflection of both the incompetence of increased flows to erode and resistance provided by perimeter sediments. Sites with erosion features appear not to have yet attained new equilibrium conditions.     

Methane in the hyporheic zone of a small lowland stream (Sitka, Czech Republic)

Methane concentrations and selected chemical parameters in interstitial water were examined along subsurface flowpath in two subsystems (hyporheic and parafluvial sediments) in the Sitka stream, Czech Republic. Interstitial methane concentrations exhibited a distinct spatial pattern. In the hyporheic downwelling zone where the sediments are relatively well oxygenated due to high hydrologic exchange with the surface water, low interstitial methane concentrations, averaging 9.3 μg CH₄/l, were found. In contrast, upwelling sediments and parafluvial sediments (active channel sediments lateral to the wetted channel) had significantly higher methane concentrations (p < 0.05, and p < 0.01, respectively), averaging 43.2 μg CH₄/l and 160.5 μg CH₄/l, respectively. Dissolved oxygen was the highest where surface water entered hyporheic/parafluvial sediments and decreased with water residence time in the sediments (p < 0.01). Nitrate concentrations decreased along the flowpath and were significantly lower at downstream end of the riffle (p < 0.001). Sulfate concentrations also show a slight decline with the water residence time, but differences were not significant. Effect of both nitrate and sulfate on methanogenesis is also discussed. The interstitial methane concentration significantly increased with surface water temperature (p < 0.001) and was negatively correlated with redox potential (p < 0.01) and dissolved oxygen (p < 0.05).     

Recent changes in the sediment regime of the Pearl River (South China): Causes and implications for the Pearl River Delta

Riverine sediments have played an important role in the morphological evolution of river channels and river deltas. However, the sediment regime in the many world's rivers has been altered in the context of global changes. In this study, temporal changes in the sediment regime of the Pearl River were examined at different time scales, that is, annual, seasonal, and monthly time scales, using the Mann–Kendall test. The results revealed that precipitation variability was responsible for monthly and seasonal distribution patterns of the sediment regime and the long‐term changes in the water discharge; however, dam operation has smoothed the seasonal distribution of water discharge and resulted in decreasing trends in the annual, wet‐season, and dry‐season sediment load series since the 1950s. Due to the different regulation magnitudes of dam operation, differences were observed in sediment regime changes among the three tributaries. In addition, human activities have altered the hysteresis of seasonal rating curves and affected hysteresis differences between increasing and decreasing water discharge stages. Sediment supply is an important factor controlling river channel dynamics, affecting channel morphology. From the 1950s to the 1980s, siltation was dominant in river channels across the West River and North River deltas in response to the sediment increases; however, scouring occurred in the East River deltas due to sediment reduction. Significant erosion occurred in river channels in the 1990s, which was mostly due to downcutting of the river bed caused by sand excavations and partly because of the reduced sediment load from upstream. Although sand excavations have been banned and controlled by authority agencies since 2000, the erosion of cross sections was still observed in the 2000s because of reduced sediment caused by dam construction. Our study examines the different effects of human activities on the sediment regime and downstream channel morphology, which is of substantial scientific importance for river management.     

Overbank sediment deposition patterns for straight and meandering flume channels

Experiments with the 10 m Flood Channel Facility at HR Wallingford, UK, indicate a fundamental dependency of the overbank deposition pattern of channel suspended sediments on channel planform. Two experiments (100 and 140 l s^?1) in a 1·95 m wide straight channel showed deposition concentrated in a berm along the channel bank. Little sediment was transferred further onto the floodplain. For the larger flow, the berm formed further from the channel. A single experiment (103 l s^?1) with a 1·31 m wide meandering channel showed deposition across the entire floodplain tongue between successive meanders. Maximum deposition occurred on the downstream side of the meander, just past the bend apex. These generalized flume results complement the real‐world but site‐specific data of field studies. Copyright © 2002 John Wiley & Sons, Ltd.     

The structure of ice and ice cover in lower Amur reaches with branched channel

The study is focused on the specific features of ice regime in Amur lower reaches and the structure of ice surface in branches of different size and dynamic state. The main features of ice stratigraphy in different parts of the river have been identified, and ice cover characteristics have been found to show considerable heterogeneity across the channel. Quantitative data on the concentration of terrigenous material in the ice and its distribution within the ice mass have been collected. The amount of terrigenous material was estimated in the ice in Amur lower reaches, from where it is largely exported into the Sea of Okhotsk during spring ice drift.     

Estimate of fine sediment deposit dynamics over a gravel bar using photography analysis

Three different methods to analyse fine sediment deposits on a gravel bar using pictures are presented in this paper. A manual digitization and deposits zone delineation are performed as well as two different automated procedures. The three methods are applied on aerial pictures taken in 2006 by a drone from a height around 150 m above the study site. Two other sets of pictures taken in 2010 are also studied: the first set was obtained from the left side bank of the river at approximately 15m above the gravel bar whereas the second one was taken from a helicopter flying 600～m above the ground. These methods were used to estimate the surface of fine sediment deposits before and after flushing events. They yield similar results even if the first automated procedure is able to capture smaller patches of fine sediments. The total surface of fine sediment deposits seems to be similar before and after a flushing event, but the distribution appears quite different. Before a flushing event, a significant amount of fine sediment deposits are mixed with coarser sediments. After the flushing event, one can observe more large fine sediment deposits located on the downstream part of the secondary channel and at the channel margin. Most of the small fine sediment deposit patches were washed out. A short discussion is provided on the possible dynamics of fine sediment deposits over the gravel bar.     

Controls on knickpoint migration in a drainage network of the moderately uplifted Ardennes Plateau,Western Europe

Much research has been devoted to the development of numerical models of river incision. In settings where bedrock channel erosion prevails, numerous studies have used field data to calibrate the widely acknowledged stream power model of incision and to discuss the impact of variables that do not appear explicitly in the model's simplest form. However, most studies have been conducted in areas of active tectonics, displaying a clear geomorphic response to the tectonic signal. Here, we analyze the traces left in the drainage network 0.7 My after the Ardennes region (western Europe) underwent a moderate 100–150 m uplift. We identify a set of knickpoints that have traveled far upstream in the Ourthe catchment, following this tectonic perturbation. Using a misfit function based on time residuals, our best fit of the stream power model parameters yields m = 0.75 and K = 4.63 × 10^‐8 m^‐0.5y^‐1. Linear regression of the model time residuals against quantitative expressions of bedrock resistance to erosion shows that this variable does not correlate significantly with the residuals. By contrast, proxies for position in the drainage system prove to be able to explain 76% of the residual variance. High time residuals correlate with knickpoint position in small tributaries located in the downstream part of the Ourthe catchment, where some threshold was reached very early in the catchment's incision history. Removing the knickpoints stopped at such thresholds from the data set, we calculate an improved m = 0.68 and derive a scaling exponent of channel width against drainage area of 0.32, consistent with the average value compiled by Lague for steady state incising bedrock rivers. Copyright © 2014 John Wiley & Sons, Ltd.     

Estimating bed material fluxes upstream and downstream of a controlled large bifurcation - the Mississippi-Atchafalaya River diversion

Bed material transport at river bifurcations is crucial for channel stability and downstream geomorphic dynamics. However, measurements of bed material transport at bifurcations of large alluvial rivers are difficult to make, and standard estimates based on the assumption of proportional partitioning of flow and bedload transport at bifurcations may be erroneous. In this study, we employed a combined approach based on observed topographic change (erosion/deposition) and bed material transport predicted from a one-dimensional model to investigate bed material fluxes near the engineering-controlled Mississippi-Atchafalaya River diversion, which is of great importance to sediment distribution and delivery to Louisiana's coast. Yang's (1973) sediment transport equation was utilized to estimate daily bed material loads upstream, downstream, and through the diversion during 2004–2013. Bathymetric changes in these channels were assessed with single beam data collected in 2004 and 2013. Results show that over the study period, 24% of the Mississippi River flow was diverted into the Atchafalaya River, while the rest remained in the mainstem Mississippi. Upstream of the diversion, the bed material yield was predicted to be 201 million metric tons (MT), of which approximately 35 MT (i.e., 17%) passed through the bifurcation channel to the Atchafalaya River. The findings from this study reveal that in the mainstem Mississippi, the percentage of bed material diversion (83%) is larger than the percentage of flow diversion (76%); Conversely, the diversion channel receives a disproportionate amount of flow (24%) relative to bed material supply (17%). Consequently, severe bed scouring occurred in the controlled Outflow Channel to the Atchafalaya River, while riverbed aggradation progressed in the mainstem Mississippi downstream of the diversion structures, implying reduced flow capacity and potential risk of a high backwater during megafloods. The study demonstrates that Yang's sediment transport equation provides plausible results of bed material fluxes for a highly complicated large river diversion, and that integration of the sediment transport equation with observed morphological changes in riverbed is a valuable approach to investigate sediment dynamics at controlled river bifurcations.     

Seasonal variations of the distribution of river water quality

The probability distributions of different values of water quality indices have been shown theoretically to follow a two-parameter lognormal law with season-dependent parameters. The obtained distribution law was checked against data of many-year water quality monitoring in the Moskva R. (at Rublevo Settl.). The distributions of several hydrochemical and microbiological indices have been studied. The seasonal dependence of parameters have been shown to cause the splitting of water quality index distributions predominantly into two lognormal branches, one corresponding to low-water seasons and the other corresponding to floods. Exceptions are water turbidity and color index: the former splits into three lognormal branches (corresponding to periods of winter low-water period, summer period with moderate rains, floods, and high rain floods), while the color index has only one branch, embracing all seasons.     

Topographic forcing of flow partition and flow structures at river bifurcations

This paper presents the predicted flow dynamics from the application of a Reynolds‐averaged Navier–Stokes model to a series of bifurcation geometries with morphologies measured during previous flume experiments. The topography of the bifurcations consists of either plane or bedform‐dominated beds which may or may not possess discordance between the two bifurcation distributaries. Numerical predictions are compared with experimental results to assess the ability of the numerical model to reproduce the division of flow into the bifurcation distributaries. The hydrodynamic model predicts: (1) diverting fluxes in the upstream channel which direct water into the distributaries; (2) super‐elevation of the free surface induced at the bifurcation edge by pressure differences; and (3) counter‐rotating secondary circulation cells which develop upstream of the apex of the bifurcation and move into the downstream channels, with water converging at the surface and diverging at the bed. When bedforms are not present, weak transversal fluxes characterize the upstream channel for almost its entire length, associated with clearly distinguishable secondary circulation cells, although these may be under‐estimated by the turbulence model used in the solution. In the bedform dominated case, the same hydrodynamic conditions were not observed, with the bifurcation influence restricted and depth scale secondary circulation cells not forming. The results also demonstrate the dominant effect bed discordance has upon flow division between the two distributaries. Finally, results indicate that in bedform dominated rivers. Consequently, we suggest that sand‐bed river bifurcations are more likely to have an influence that extends much further upstream and have a greater impact upon water distribution. This may contribute to observed morphological differences between sand‐bedded and gravel‐bedded braided river networks. Copyright © 2012 John Wiley & Sons, Ltd.     

Transport and deposition of fine sediment in open channels with different aspect ratios

This paper investigates by means of several large eddy simulations how the channel aspect ratio affects the transport and settling of suspended sediments. The numerical method is successfully validated using data of a physical experiment of fine sediment net deposition in an open channel flow. The channel aspect ratio, A, is known to be the determining factor for the development, strength and distribution of the turbulence‐driven secondary flow, and it is demonstrated that A influences the primary flow, turbulence quantities and the transport and fate of fine sediments. The secondary flow locally supports or hinders the falling of fine sediment particles in a turbulent flow, which results in a non‐uniform deposition of fine sediments over the cross‐section. While the channel aspect ratio has a large influence on the distribution of suspended sediments within the cross‐section, its effect on the cross‐sectional averaged deposition is negligibly small. Copyright © 2012 John Wiley & Sons, Ltd.     

A multi‐scale statistical approach to assess the effects of connectivity of road and stream networks on geomorphic channel condition

Roads in rural, upland landscapes are important sources of runoff and sediment to waterways. The downstream effects of these sources should be related to the connectivity of roads to receiving waters. Recent studies have explored this idea, but only simple metrics have been used to characterize connectivity and few studies have quantified the downstream effects of road–stream connectivity on sediment or solute budgets and channel morphology. In this study, we evaluated traditional and newly developed connectivity metrics that utilized features of landscape position and delivery pathway to characterize road–stream connectivity in upland settings. Using data on stream geomorphic conditions developed by the Vermont Agency of Natural Resources (Montpelier, VT), we related road connectivity metrics to channel condition on a set of 101 forested, upland streams with minimal development other than predominantly gravel road networks. Logistic regression indicated that measures of road density, proximity and orientation successfully distinguished among categories of stream geomorphic condition at multiple geographic scales. Discriminant function analysis using a set of inherent channel characteristics combined with road connectivity metrics derived at the reach corridor scale successfully distinguished channel condition for over 70% of the channels evaluated. This research contributes to efforts to evaluate the cumulative downstream effects of roads on stream channels and aquatic resources and provides a new means of watershed assessment to derive metrics that can be used to predict channel condition. Copyright © 2014 John Wiley & Sons, Ltd.     

Float‐transient electromagnetic method: in‐loop transient electromagnetic measurements on Lake Holzmaar,Germany

Lake sediments may serve as archives on paleoclimatic fluctuations, geomagnetic field variations and volcanic activities. Lake Holzmaar in Eifel/Germany is a maar lake and its lacustrine sediments provide paleoclimatic proxy data. Therefore, knowledge about the geometry and, especially, about the thickness of the sediments is very important for determining an optimum drilling location for paleoclimatic studies. We have developed a floating in‐loop transient electromagnetic method field set up (Float‐transient electromagnetic method) with a transmitter and receiver size of 18 × 18 m² and 6 × 6 m² respectively. This special set up enables in‐loop transient electromagnetic method measurements on the surface of freshwater lakes that define the geometry and the thickness of sediments beneath such lakes thus helping to determine optimum drilling locations. Due to the modular design of the new Float‐transient electromagnetic method field set up, this system can be handled by two operators and can easily be transported. Sixteen in‐loop soundings were carried out on the surface of Lake Holzmaar. The transient electromagnetic method data could not be interpreted by conventional 1D inversions because of the 3D distribution of subsurface conductivity caused by the lake's geometry. Three‐dimensional finite element modelling was applied to explain the observed transients and the 3D conductivity distribution beneath the lake was recovered by taking its geometry into account. The 3D interpretation revealed approximately 55 m thick sediments beneath 20 m deep water in the central part of the lake.     

Dynamic flood topographies in the Terai region of Nepal

Flood hazard maps used to inform and build resilience in remote communities in the Terai region of southern Nepal are based on outdated and static digital elevation models (DEMs), which do not reflect dynamic river configuration or hydrology. Episodic changes in river course, sediment dynamics, and the distribution of flow down large bifurcation nodes can modify the extent of flooding in this region, but these processes are rarely considered in flood hazard assessment. Here, we develop a 2D hydrodynamic flood model of the Karnali River in the Terai region of west Nepal. A number of scenarios are tested examining different DEMs, variable bed elevations to simulate bed aggradation and incision, and updating bed elevations at a large bifurcation node to reflect field observations. By changing the age of the DEM used in the model, a 9.5% increase in inundation extent was observed for a 20-year flood discharge. Reducing horizontal DEM resolution alone resulted in a <1% change. Uniformly varying the bed elevation led to a 36% change in inundation extent. Finally, changes in bed elevation at the main bifurcation to reflect observed conditions resulted in the diversion of the majority of flow into the west branch, consistent with measured discharge ratios between the two branches, and a 32% change in inundation extent. Although the total flood inundation area was reduced (−4%), there was increased inundation along the west bank. Our results suggest that regular field measurements of bed elevation and updated DEMs following large sediment-generating events, and at topographically sensitive areas such as large river bifurcations, could help improve model inputs in future flood prediction models. This is particularly important following flood events carrying large sediment loads out of mountainous regions that could promote bed aggradation and channel switching across densely populated alluvial river systems and floodplains further downstream. © 2020 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd