动力学模型预测小黄鱼(Pseudosciaena polyactis)鱼干常温保藏下的货架期

为了预测小黄鱼(Pseudosciaena polyactis)鱼干的货架期,对贮藏在30°C、35°C、40°C下的小黄鱼干的品质进行测定,通过测定菌落总数、酸价、过氧化值三个指标在贮藏期间的变化,分别对这三个指标与贮藏时间、温度建立一级动力学方程及Arrhenius方程,建立小黄鱼干货架期预测模型。经计算得出,菌落总数预测模型中的活化能(Ea)及指前因子(k0)分别为29.26kJ/mol和4.46×102,酸价预测模型中的的活化能及指前因子分别为47.05kJ/mol和4.1×105,过氧化值预测模型中的活化能及指前因子分别为49.76kJ/mol和1.53×106。在37°C和42°C条件下验证动力学模型,结果表明相对误差分别为?4.68%和?6.25%,准确性较好。进一步推算得出,在20°C和25°C常温下贮藏小黄鱼干,产品的货架期为500d和352d。     

海捕大管鞭虾(Solenocera melantho)调理食品在常温保藏中的货架期预测及产品质量分析

本文测定了海捕大管鞭虾(Solenocera melantho)(又称红虾)调理食品在不同温度保藏中的细菌总数、挥发性盐基氮(TVB-N)值、pH值及感官评价等参数。通过对虾肉色泽、组织质构、风味和外形四个方面的检测,综合各项指标决定将TVB-N作为该产品质量变化和推测货架期时长的关键指标。将各温度下测定的TVB-N值代入线性方程组计算出反应活化能E_a为55.21 k J/mol,指前因子k_0为1.08×10~9。利用Arrhenius方程外推法计算得出在20°C和25°C温度下TVB-N值变化速率常数分别为k_(20°C)=0.1405和k_(25°C)=0.2386,从而进一步确定该条件下保藏的理论货架期分别为153.6d和92.1d。经质构仪分析红虾虾仁的硬度与弹性变化,综合感官评定结果和其它测定值,确定海捕红虾产品在常温贮藏中的货架期为3个月。本研究为常温下红虾调理食品的保藏提供了理论依据。     

动力学模型预测泥鳅(Misgurnus anguillicaudatus)半干制品的货架期

以泥鳅(Misgurnus anguillicaudatus)半干制品为研究对象,测定和分析其在不同贮藏温度(4°C、20°C、30°C和40°C)下,菌落总数、挥发性盐基氮(TVBN)、脂肪氧化程度(TBA值)与感官评分各项指标随贮藏时间的变化。结果表明,泥鳅半干制品在不同贮藏温度下,随着贮藏时间的延长品质逐渐下降,贮藏温度越低,品质指标变化越缓慢。经Pearson相关性分析,确定影响泥鳅半干制品品质变化的关键因子为菌落总数;基于Arrhenius方程,进一步建立菌落总数与贮藏时间、贮藏温度之间的动力学模型,该模型中活化能Ea为26.5 kJ/mol,反应速率常数k0为3186.6,推算得出泥鳅半干制品货架期预测值与实测值相对误差较小,该动力学模型可准确预测泥鳅半干制品在4—40°C贮藏温度下的货架期。本研究可为泥鳅半干制品的开发、流通奠定理论基础。     

流化冰对于鲣鱼的保鲜效果研究

以远洋鲣鱼为研究对象,以传统淡水碎冰保鲜为对照,研究流化冰处理对鲣鱼的理化性质及微生物特性的影响。结果表明:(1)–4°C冷藏18d后,流化冰保鲜鱼肉pH值、TVB-N、TBA、a*值和菌落总数依次为5.57、10.2mgN/100g、2.87mg/100g、8.92和2.61lgCFU/g,而淡水碎冰保鲜鱼肉各指标已达6.05、20.3mgN/100g、6.60mg/100g、7.16和3.02lgCFU/g,故可知流化冰保鲜处理效果明显优于碎冰保鲜。(2)在25±1°C室温条件下,将冰与鱼放入保温箱内保鲜8h后,流化冰保鲜鱼肉的a*值、pH值、TVB-N、TBA、菌落总数和汁液流失率均显著低于空白和淡水碎冰保鲜处理组(P0.05)。流化冰保鲜可显著减缓鱼体的腐败进程、延长产品货架期,进而满足冰鲜水产品的远洋及长距离运输要求。     

贮藏温度对中国毛虾(Acetes chinensis)品质变化影响的研究

为探究贮藏温度对中国毛虾品质的影响,通过感官评分,菌落总数和理化指标的测定,分析毛虾虾皮在不同贮藏温度下的品质变化。结果表明:25°C及37°C贮藏期间感官评分、亮度值(L*)显著下降,红度值(a*)、黄度值(b*)、菌落总数显著增加(P0.05),p H值先缓慢增加后趋于稳定,TVB-N和TBA值在贮藏前期均缓慢增加,后期增加显著。4°C贮藏下,感官评分缓慢下降,p H值、菌落总数基本不变,贮藏30 d后,L*、a*、b*、TVB-N及TBA值呈现显著变化(P0.05)。综合分析,不同温度对毛虾虾皮贮藏期的色泽、感官评分、TVB-N、TBA、p H值及菌落总数变化均有显著影响;毛虾皮在25°C和37°C下分别贮藏至15 d及9 d时,已严重发黄并产生异味,菌落总数均大于107CFU/g,已腐败变质。4°C下贮藏至60 d时毛虾虾皮仍未失去食用价值,说明低温能显著延长毛虾虾皮的贮藏时间。     

凡纳滨对虾(Litopenaeus vannamei)即食虾仁在常温保藏中的货架期预测及品质分析

采用化学分析、质构检测及动力学模型建立等方法, 对凡纳滨对虾(Litopenaeus vannamei)即食虾仁在常温保藏中的细菌总数、TVB-N值、pH值、质构特性、色差值及感官评价等参数进行测定。以挥发性盐基氮TVB-N作为货架寿命的关键指示因子, 利用Arrhenius法预测常温流通高水分即食调味虾仁的货架寿命。计算结果Ea为65.26kJ/mol, k0为6.04×109, 进一步推算得到在20℃和25℃常温流通条件下, 即食虾仁产品的货架期为148.61d和94.1d。在25℃保藏3个月的虾仁虽在细菌总数、TVB-N值、pH值、感官评分、质构、色差值等方面均发生了一些变化, 但都在安全范围之内, 不影响其食用价值。本研究为常温流通的即食虾仁产品开发奠定了理论基础。     

低硼氢氧化镁的制备及热分解动力学参数

本文以水合氯化镁、工业氨水为原料制备出了低硼含量的纯度 >99%的氢氧化镁和氧化镁。利用差热 -热重 (DTA- TG)、X-射线衍射 (XRD)、透射电子显微镜 (TEM)等手段 ,对氢氧化镁的热稳定性、相结构、表观状态以及脱水动力学参数进行了分析。结果为 :氢氧化镁以束状纤维和片状粉末共存 ,在 6 2 3K基本完成脱水反应生成氧化镁 ,其脱水反应的表观活化能 E为135 .4 k J· mol-1,指前因子 A为 5 .15× 10 10 ,反应级数 n为 1.10     

氧化亚铜的氧化动力学

本文以亚硫酸盐和硫酸铜制备的氧化亚铜为样品,用Kissinger法和FWO法研究了氧化亚铜的氧化动力学行为,结果表明:氧化亚铜氧化反应生成氧化铜的表观活化能E=174.52 kJ.mol-1,指前因子lnA=195.526 8,相对应的反应级数n=0.99。     

氧化亚铜的氧化动力学

本文以亚硫酸盐和硫酸铜制备的氧化亚铜为样品,用Kissinger法和FWO法研究了氧化亚铜的氧化动力学行为,结果表明:氧化亚铜氧化反应生成氧化铜的表观活化能E=174.52 kJ·mol-1,指前因子lnA=195.526 8,相对应的反应级数n=0.99.     

海水中铜与针铁矿离子交换的动力学研究

本文较系统地研究了海水体系中Cu(Ⅱ)与α-FeOOH间的离子/配位子交换动力学。实验测定反应级数n=1;速率常数k(25℃)=6.12、k(35℃)=8.40;活化能E_a=2.43×10~4J/mol。反应第一阶段的速率由固有液膜扩散所控制;反应第二阶段的速率由递进液膜扩散所控制。反应全过程可统一地用固有液膜扩散和递进液膜扩散的复合模型、描述,理论计算与实验测定相吻合。     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,