海水中低含量铵氮的高灵敏度荧光法测定

提出了一种改进的、可测定海水中低含量铵氮的高灵敏度荧光分析方法。其原理是在硼酸缓冲溶液的作用下,海水中的铵氮与邻苯二甲醛(OPA)发生衍生化反应,通过测定生成的荧光产物来确定水体中铵氮的浓度。方法的检测限极低(0.002 5μmol/L),重现性好,且水样用量少(10 mL),适用于海水中溶解有机物的光铵化研究及其他低铵含量水样的测定。     

基于荧光法的海水氨氮测量方法研究

对邻苯二甲醛荧光法测量海水中氨氮进行了研究。实验研究了该体系测定氨氮的最佳条件,结果表明亚硫酸钠对该体系具有良好的增敏增稳作用,盐度(20～35)对测量结果无影响(引起误差在±1.5%以内)。氨氮测定的线性范围为2～300μg/L,精密度(相对标准偏差RSD)均小于3%。     

AccQ-Tag法测定毛蚶抗贫血口服液中的氨基酸含量

以 6 -氨基喹啉 - N-羟基琥珀酰亚胺基氨基甲酸酯 (AQC)为衍生剂 ,与毛蚶抗贫血口服液中的氨基酸柱前定量衍生 ,用 Waters HPL C仪 ,Acc Q- Tag TM专用 C18柱 (3.9mm× 15 cm) ,以140 mmol· L-1的醋酸钠溶液 (p H5 .0 2 )为溶剂 A,乙腈为溶剂 B,超纯水 (Milli- Q水 )为溶剂 C,进行梯度洗脱 ,检测波长为 2 4 8nm,35 min测试完毕。各种氨基酸测定的重现性 RSD%均 <3.0 %(n=5 )。该方法简便快速 ,结果准确可信。     

吹扫-捕集气相色谱法测定海水中挥发性卤代烃

挥发性卤代烃(VHC)是大气中的痕量气体,对臭氧层损耗和温室效应有重要作用。海洋是大气中VHC的主要自然排放源,开展海洋VHC的研究有助于了解海洋对大气VHC和全球变暖的贡献。本文建立了吹扫-捕集与气相色谱-微池电子捕获检测器联用技术(P-T-GC-(ECD)分析海水中6种VHC的方法,确定了吹扫-捕集条件和气相色谱分离条件。该方法的检测限在0.003~0.369 ng.L-1之间;相对标准偏差是1.83~3.97;加标回收率为98.1%~110.2%;相关系数在0.997 3~0.999 8之间。可准确地测定海水中6种VHC。     

RP-HPLC法同时测定翅碱蓬中四种黄酮化合物的含量

建立RP-HPLC(反相高效液相色谱法)同时测定翅碱蓬中四种黄酮化合物-芸香苷、槲皮素3-β-D-葡萄糖苷、水仙苷和槲皮素的含量。采用Kromasil C18色谱柱(4.6 mm×250 mm,5μm),检测波长为361nm,柱温为30℃,流动相为甲醇-0.4%冰乙酸(55︰45),流速1.0mL/min,四种黄酮类化合物得到很好的分离。芸香苷、槲皮素3-β-D-葡萄糖苷、水仙苷和槲皮素浓度均为0.001~0.01 mg/mL范围内呈现良好线性关系,相关系数R2在0.9990~0.9996,加标回收率(n=3)范围为82.39%~99.03%。该方法简单、快速、高效,可以用于翅碱蓬中四种黄酮化合物的含量分析。     

小粘膜藻4种化合物的分离和结构鉴定

利用正相硅胶、生物胶Bio—beads、Sephadex LH-20柱色谱、反相HPLC及重结晶等分离手段,从小粘膜藻(Leathesia nana)中分离得到4个化合物,通过IR、MS、ID和2D NMR等现代波谱技术鉴定结构为：吲哚-3甲酸(1)、3,5-二经基-4-甲氧基苯甲醇(2)、1-O-十六烷酰基甘油酯(3)和岩藻甾醇(4)。以上化合物均为首次从该属海藻中分离鉴定。     

海水中丙烯酸的高效液相色谱法建立及应用

建立了一种测定海水介质中丙烯酸的高效液相色谱法。采用耐纯水相和较低pH的Agilent SB-Aq-C18柱(100 mm×4.6 mm i.d.,5 μm), 0.35%磷酸溶液(pH=2)为流动相,使用紫外检测器,检测波长为210 nm,外标法定量测定。丙烯酸的保留时间在14.2~ 14.9 min,方法的检出限为4 nmol/dm3(S/N=3),在0.01~10 μmol/dm3的范围内均有良好的线性关系,相关系数可达0.999 6,加标回收率为95.4%~98.1%,相对标准偏差为1.3%~1.6%(1.04~2.32 μmol/dm3)。采用0.2 μm滤膜重力过滤冷藏的办法来保存海水丙烯酸样品。检测出2011年5月份青岛近海海水中丙烯酸的平均浓度为(0.101±0.069) μmol/dm3;海洋微藻球形棕囊藻在整个生长周期内培养体系中丙烯酸的浓度为0.339~2.219 μmol/dm3。     

3-(3′-羟基)丁基苯酞氨基酸酯衍生物的设计与合成

3-(3′-羟基)丁基苯酞是丁苯酞在体内的代谢产物,具有多种药理作用,可以作为一种新的活性成分应用于药物开发中。本文以甘氨酸、甲硫氨酸和亮氨酸为起始原料,经过Boc保护,再与3-(3′-羟基)丁基苯酞进行缩合,脱保护3步反应合成了3-(3′-羟基)丁基苯酞的氨基酸酯。以期提高水溶性和改善药代动力学性质,获得3-(3′-羟基)丁基苯酞的前药。     

具降胆固醇功能的海洋源乳酸菌的筛选及发酵条件工艺优化

本研究采用邻苯二甲醛法从柏式中喙鲸( Mesoplodon densirostris)内脏中筛选出一株具高效降解胆固醇功能的乳酸菌HJ-S2,利用16S rDNA分子生物学和API 50CH系统鉴定其为植物乳杆菌( Lactobacillus plantarum) .为提高乳酸菌HJ-S2体外降胆固醇能力,考察了菌株的...     

用铅离子选择性电极测定海水中硫酸根

海水中硫酸根的测定至今仍用费时的重量法。铅离子选择性电极虽能准确地测定SO_4~_,但样品中大量的Cl~-干扰SO_4~(2-)的测定。Mascin为使海水中的SO_4~(2-)与Cl~-分离,将海水样品通过Ag~ 型阳离子交换树脂分离海水中的Cl~-,接着又通过H~ 型阳离子树脂(树脂层均为15×0.5cm)分离Ag~ ,最后将流出液调到pH 5—6后,用铅离子选择性电极为指示电极进行电位滴定。该方法较烦,且树脂易被Ag~ 氧化而使交换容量变得很低。Scheide采用将样品稀释100倍,不经分离而直接在80％异丙醇溶液中进行Gran     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Phylogenetic diversity and phenotypic characterization of cultivable bacterioplankton isolated from polar oceans

A set of 27 marine planktonic bacteria isolated from the polar regions was characterized by 16S rDNA sequencing and physiological and biochemical testing. More than half of these bacteria were positive for caseinase, gelatinase and 13-glucosidase, and could utilize glucose, maltose or malic acid as carbon source for cell growth. Twelve isolates expressed nitrate reduction activities. Except for one antarctic isolate BSwlO175 belonging to Actinobacteria phylum, these isolates were classified as γ-Proteobacteria, suggesting that γ-Proteobacteria dominated in cultivable marine bacterioplankton at both poles. Genus Pseudoalteromonas was the predominant group in the Chukchi Sea and the Bering Sea, and genus ShewaneUa dominated in cultivable bacterioplankton in the Prydz Bay. With sequence similarities above 97%, genus Psychrobacter was found at both poles. These 27 isolates were psychrotolerant, and significant 16S rDNA sequence similarities were found not only between arctic and antarctic marine bacteria （ 〉 99% ）, but also between polar marine bacteria and bacteria from other aquatic environments （ ≥ 98.8% ）, including temperate ocean, deep sea, pond and lake, suggesting that in the polar oceans less temperature-sensitive bacteria may be cosmopolitan and have a bipolar, even global, distribution at the species level.     

Deep-Sea Sediment Compression Curves: Some Controlling Factors, Spurious Overconsolidation, Predictions, and Geophysical Reproduction

Oedometer tests have been carried out on 70 undisturbed surficial clays (at approximately 250 mm below the mudline), mostly collected by free-fall corers from sites widely scattered throughout the deep-sea North Atlantic. Acoustic measurements were also made, initially on contiguous samples and ultimately on the same sample using a geophysically instrumented oedometer which also collected electrical resistivity data. Apart from those quiescent areas below the carbonate compensation depth, such as north of the West Indies where very fine clays exist, most of the samples are silty clays whose geotechnical-geophysical properties are dependent on the type of clay minerals present (and their ability to take in moisture), the sand-size fraction, and the quantity of carbonate present. Thus the pure clays have high compressibilities which decrease on the addition of coarse particles, while the converse is true for the acoustic parameters, these increasing with the sand fraction. Using the notion of the intrinsic compression line for all samples, and comparison to it of the measured compression curves, it is clear that, contrary to some previously held ideas, most deep-sea clays are normally consolidated; the addition of carbonate has the effect of creating an open, stronger sediment skeleton. Interestingly, where information is available, the variation with depth of a sample's acoustic velocity follows the void ratio pressure relationship of the compression curve. This allows the construction of an in-situ sediment compression curve using the in-situ geophysical observations.