Modelling of elastoplastic damage in concrete due to desiccation shrinkage

We present a numerical modelling of elastoplastic damage due to drying shrinkage of concrete in the framework of mechanics of partially saturated porous media. An elastoplastic model coupled with isotropic damage is first formulated. Two plastic flow mechanisms are involved, controlled by applied stress and suction, respectively. A general concept of net effective stress is used in take into account effects of capillary pressure and material damage on stress‐controlled plastic deformation. Damage evolution depends both on elastic and plastic strains. The model's parameters are determined or chosen from relevant experimental data. Comparisons between numerical simulations and experimental data are presented to show the capacity of model to reproduce mains features of concrete behaviour under mechanical loading and during drying shrinkage of concrete. An example of application concerning drying of a concrete wall is finally presented. The results obtained allow to show potential capacity of proposed model for numerical modelling of complex coupling processes in concrete structures. Copyright © 2002 John Wiley & Sons, Ltd.     

Fuzzy parameters analysis of time‐dependent fracture of concrete dam models

In order to apply the mechanical properties (measured on material specimens or laboratory‐sized models) to large structures (such as concrete dams), a non‐linear theory able to predict the size‐scale effect has to be used. One of these theories was first proposed by Hillerborg and co‐workers (fictitious crack model) and is based on the earlier works by Barenblatt and Dugdale for metals (cohesive crack model). It is based on the existence of a fracture process zone (FPZ), where the material undergoes strain softening. The behaviour of the material outside the FPZ is linear elastic. A large number of short‐time laboratory tests were executed, by varying the load, under crack mouth opening displacement control. Since concrete exhibits a time‐dependent behaviour, an interaction between creep and micro‐crack growth occurs in the FPZ. Therefore, different testing conditions can be applied: rupture can be achieved by keeping the load constant before peak value (pre‐peak tests), or after peak value and after an unloading and reloading procedure (post‐peak tests). The crack propagation rate is shown to be small enough to neglect inertial forces and large enough to keep the time‐dependent behaviour of the process zone as dominant compared to the behaviour of the undamaged and viscoelastic zone. Due to the variability in material microstructure from one specimen to another, experimental data show large ranges of scatter. Well established methods in probability theory require sufficient experimental data in order to assume a probability density distribution. The objective of this study is to investigate the ranges of variation of the time response under constant load in simple structural elements associated with pre‐selected variation (fuzziness) in the main material parameters. For situations where the values of the material parameters are of a non‐stochastic nature, the fuzzy set approach to modelling variability has been proposed as a better and more natural approach. Copyright © 2002 John Wiley & Sons, Ltd.     

A mesoscopic model for the behaviour of concrete under high confinement

When impact loaded, concrete is submitted to high triaxial stresses. The experimental response of concrete under quasi‐static triaxial compression is studied using a triaxial press capable of applying a mean pressure greater than 1 GPa on cylindrical samples measuring 7 cm in diameter and 14 cm high. A numerical analysis of these previous experiments is performed herein at a mesoscopic scale. Concrete is modelled as a biphasic material consisting of a mortar (cement paste and fine aggregates) and roughly spherical aggregates (with a diameter exceeding 2 mm) whose characteristics are applied on a regular cubic finite element mesh. A damage‐plasticity model is then used to model the behaviour of mortar. An identification of model parameters on mortar samples and the subsequent comparison between numerical and experimental tests will be presented for hydrostatic and triaxial compression. Copyright © 2009 John Wiley & Sons, Ltd.     

A visco‐damage model for brittle materials under monotonic and sustained stresses

A theoretical model is proposed to describe the evolution of damage in brittle materials, such as concrete and masonry, subjected to increasing or sustained stresses of relatively high intensity. The model is based on the introduction of suitable damage variables in a rheological model. In this way, it is possible to describe the material behaviour under stresses either increasing or constant in time. The capabilities of the model in describing the mechanical response of material elements subjected to different stress histories are illustrated. Some correlations with experimental data from tests performed on masonry and concrete specimens are presented, to assess the reliability of the theoretical predictions. The results of some numerical applications to non‐proportional stress paths are also illustrated. Finally, the limitations of the proposal are discussed and possible further improvements are envisaged. Copyright © 2005 John Wiley & Sons, Ltd.     

A coupled damage–plasticity model for concrete based on thermodynamic principles: Part I: model formulation and parameter identification

The development of a coupled damage‐plasticity constitutive model for concrete is presented. Emphasis is put on thermodynamic admissibility, rigour and consistency both in the formulation of the model, and in the identification of model parameters based on experimental tests. The key feature of the thermodynamic framework used in this study is that all behaviour of the model can be derived from two specified energy potentials, following procedures established beforehand. Based on this framework, a constitutive model featuring full coupling between damage and plasticity in both tension and compression is developed. Tensile and compressive responses of the material are captured using two separate damage criteria, and a yield criterion with a multiple hardening rule. A crucial part of this study is the identification of model parameters, with these all being shown to be identifiable and computable based on standard tests on concrete. Behaviour of the model is assessed against experimental data on concrete. Copyright © 2007 John Wiley & Sons, Ltd.     

Dynamic sliding of tetrahedral wedge: The role of interface friction

The role of interface friction is studied by slow direct shear tests and rapid shaking table experiments in the context of dynamic slope stability analysis in three dimensions. We propose an analytical solution for dynamic, single and double face sliding and use it to validate 3D‐DDA. Single face results are compared with Newmark's solution and double face results are compared with shaking table experiments performed on a concrete tetrahedral wedge model, the interface friction of which is determined by constant velocity and velocity stepping, direct shear tests. A very good agreement between Newmark's method on one hand and our 3D analytical solution and 3D‐DDA on the other is observed for single plane sliding with 3D‐DDA exhibiting high sensitivity to the choice of numerical penalty value. The results of constant and variable velocity direct shear tests reveal that the tested concrete interface exhibits velocity weakening. This is confirmed by shaking table experiments where friction degradation upon multiple cycles of shaking culminated in wedge run out. The measured shaking table results are fitted with our 3D analytical solution to obtain a remarkable linear logarithmic relationship between friction coefficient and sliding velocity that remains valid for five orders of magnitude of sliding velocity. We conclude that the velocity‐dependent friction across rock discontinuities should be integrated into dynamic rock slope analysis to obtain realistic results when strong ground motions are considered. Copyright © 2011 John Wiley & Sons, Ltd.     

Identifying parameters controlling soil delayed behaviour from laboratory and in situ pressuremeter testing

The aim of this paper is to present a methodology for identifying the soil parameters controlling the delayed behaviour from laboratory and in situ pressuremeter tests by using an elasto‐viscoplastic model (EVP‐MCC) based on Perzyna's overstress theory and on the elasto‐plastic Modified Cam Clay model. The influence of both the model parameters and the soil permeability was studied under the loading condition of pressuremeter tests by coupling the proposed model equations with Biot's consolidation theory. On the basis of the parametric study, a methodology for identifying model parameters and soil permeability by inverse analysis from three levels of constant strain rate pressuremeter tests was then proposed and applied on tests performed on natural Saint‐Herblain clay. The methodology was validated by comparing the optimized values of soil parameters and the values of the same parameters obtained from laboratory test results, and also by using the identified parameters to simulate other tests on the same samples. The analysis of the drainage condition and the strain rate effect during a pressuremeter test demonstrated the coupled influence of consolidation and viscous effects on the test results. The numerical results also showed that the inverse analysis procedure could successfully determine the parameters controlling the time‐dependent soil behaviour. Copyright © 2008 John Wiley & Sons, Ltd.     

Crack propagation in sandstone: Combined experimental and numerical approach

Summary A combined experimental and numerical approach is adopted to investigate crack propagation in sandstone. Experiments on two types of sandstones show a simular behaviour as found in tests on concrete specimens. The heterogeneity of the material in combination with the stress situation, as a result of the applied load, governs the direction of crack propagation. Cracks that develop are not continuous, but overlaps exist mainly around the grain particles in the material. A simple lattice model, in which the material is schematized as a network of small beams, is adopted to simulate the experiments. Using the simulations carried out with the lattice model, the control parameter for stable displacement controlled four-point-shear tests was determined. The crack patterns obtained with the model are in good agreement with the experimental observations. However further study is needed to predict the load-displacement response correctly.     

Comparison of continuous and discontinuous constitutive models to simulate concrete behaviour under mixed‐mode failure conditions

The paper presents detailed FE simulation results of concrete elements under mixed‐mode failure conditions according to the so‐called shear‐tension test by Nooru‐Mohamed, characterized by curved cracks. A continuous and discontinuous numerical two‐dimensional approach was used. In order to describe the concrete's behaviour within continuum mechanics, two different constitutive models were used. First, an elasto‐plastic model with isotropic hardening and softening was assumed. In a compression regime, a Drucker–Prager criterion with a non‐associated flow rule was used. In turn, in a tensile regime, a Rankine criterion with an associated flow rule was adopted. Second, an isotropic damage constitutive model was applied with a single scalar damage parameter and different definitions of the equivalent strain. Both constitutive laws were enriched by a characteristic length of micro‐structure to capture properly strain localization. As an alternative approach, the extended finite element method was used. Our results were compared with the experimental ones and with results of other FE simulations reported in the literature. Copyright © 2015 John Wiley & Sons, Ltd.     

Some Effects of Shearing Velocity on the Shear Stress-Deformation Behaviour of Hard–Soft Artificial Material Interfaces

Shear behaviour of the joints formed by the interface of two different material types, such as rock and cemented paste backfill, rock and concrete or two different rock types, have practical importance in many rock engineering activities. This paper presents the results of an experimental investigation into the shear behaviour of these special joints under pseudo-static shear velocity. Direct shear tests on concrete–plaster interfaces were carried out under boundary conditions of constant normal load and constant normal stiffness. Shearing velocities of the performed tests were in the range of 0.3–30 mm/min. The results of the shear tests conducted on the planar and rough artificial prepared joints showed that the shearing velocity has a significant influence on the shear strength, friction angle and shear stiffness of the hard–soft material interface. So that, these parameters were decreased when shear velocity was increased. Also, comparison of the tests results that performed on the concrete–plaster joints with those from tests on the plaster–plaster and concrete–concrete interfaces showed that the shear behaviour of concrete–plaster interface is governed mainly by the shear parameters of the plaster block (namely softer material).     

A macroscopic damage‐plastic constitutive law for modeling quasi‐brittle fracture and ductile behavior of concrete

A new phenomenological macroscopic constitutive model for the numerical simulation of quasi‐brittle fracture and ductile concrete behavior, under general triaxial stress conditions, is presented. The model is particularly addressed to simulate a wide range of confinement stress states, as also, to capture the strong influence of the mean stress value in the concrete failure mechanisms. The model is based on a two‐surface damage‐plastic formulation. The mechanical behavior in different domains of the stress space is separately described by means of a quasi‐brittle or ductile material response:

相似文献   

Meso‐scale particle modeling of concrete deterioration caused by alkali‐aggregate reaction

A meso‐scale particle model is presented to simulate the expansion of concrete subjected to alkali‐aggregate reaction (AAR) and to analyze the AAR‐induced degradation of the mechanical properties. It is the first attempt to evaluate the deterioration mechanism due to AAR using the discrete‐element method. A three‐phase meso‐scale model for concrete composed of aggregates, mortar and the interface is established with the combination of a pre‐processing approach and the particle flow code, PFC2D. A homogeneous aggregate expansion approach is applied to model the AAR expansion. Uniaxial compression tests are conducted for the AAR‐affected concrete to examine the effects on the mechanical properties. Two specimens with different aggregate sizes are analyzed to consider the effects of aggregate size on AAR. The results show that the meso‐scale particle model is valid to predict the expansion and the internal micro‐cracking patterns caused by AAR. The two different specimens exhibit similar behavior. The Young's modulus and compressive strength are significantly reduced with the increase of AAR expansion. The shape of the stress–strain curves obtained from the compression tests clearly reflects the influence of internal micro‐cracks: an increased nonlinearity before the peak loading and a more gradual softening for more severely affected specimens. Similar macroscopic failure patterns of the specimens under compression are observed in terms of diagonal macroscopic cracks splitting the specimen into several triangular pieces, whereas localized micro‐cracks forming in slightly affected specimens are different from branching and diffusing cracks in severely affected ones, demonstrating different failure mechanisms. Copyright © 2012 John Wiley & Sons, Ltd.     

Coupled damage and plasticity modelling in transient dynamic analysis of concrete

In a concrete structure subjected to an explosion, for example a concrete slab, the material is subjected to various states of stress which lead to many modes of rupture. Closer to the explosive, a state of strong hydrostatic compression is observed. This state of stress produces an irreversible compaction of the material. Away from the zone of explosion, confinement decreases and the material undergoes compression with a state of stress, which is slightly triaxial. Finally, the compression wave can be reflected on a free surface and becomes a tensile wave, which by interaction with the compression wave, produces scabbing. We present, in this paper, a model aimed at describing these three failure modes. It is based on visco‐plasticity and rate dependent damage in which a homogenization method is used in order to include the variation of the material porosity due to compaction. The model predictions are compared with several experiments performed on the same concrete. Computations of split Hopkinson tests on confined concrete, a tensile test with scabbing, and an explosion on a concrete slab are presented. Copyright © 2001 John Wiley & Sons, Ltd.     

Modelling the time‐dependent behaviour of granular material with hypoplasticity

This paper presents a constitutive model for time‐dependent behaviour of granular material. The model consists of 2 parts representing the inviscid and viscous behaviour of granular materials. The inviscid part is a rate‐independent hypoplastic constitutive model. The viscous part is represented by a rheological model, which contains a high‐order term denoting the strain acceleration. The proposed model is validated by simulating some element tests on granular soils. Our model is able to model not only the non‐isotach behaviour but also the 3 creep stages, namely, primary, secondary, and tertiary creep, in a unified way.     

An anisotropic damage–plasticity model for saturated quasi‐brittle materials

This article is devoted to numerical modeling of anisotropic damage and plasticity in saturated quasi‐brittle materials such as rocks and concrete. The damaged materials are represented by an isotropic poroelastic matrix containing a number of families of microcracks. Based on previous works, a discrete thermodynamic approach is proposed. Each family of microcracks exhibits frictional sliding along crack surfaces as well as crack propagation. The frictional sliding is described by a Coulomb–Mohr‐type plastic criterion by taking into account the effect of fluid pressure through a generalized effective stress concept. The damage evolution is entirely controlled by and coupled with the frictional sliding. The effective elastic properties as well as Biot's coefficients of cracked porous materials are determined as functions of induced damage. The inelastic deformation due to frictional sliding is also taken into account. The procedure for the identification of the model's parameters is presented. The proposed model is finally applied to study both mechanical and poromechanical responses of a typical porous brittle rock in drained and undrained compression tests as well as in interstitial pressure controlled tests. The main features of material behaviors are well reproduced by the model. Copyright © 2012 John Wiley & Sons, Ltd.     

The simulation of transport processes in cementitious materials with embedded healing systems

A new model for simulating the transport of healing agents in self-healing (SH) cementitious materials is presented. The model is applicable to autonomic SH material systems in which embedded channels, or vascular networks, are used to supply healing agents to damaged zones. The essential numerical components of the model are a crack flow model, based on the Navier-Stokes equations, which is coupled to the mass balance equation for simulating unsaturated matrix flow. The driving forces for the crack flow are the capillary meniscus force and the force derived from an external (or internal) pressure applied to the liquid healing agent. The crack flow model component applies to non-uniform cracks and allows for the dynamic variation of the meniscus contact angle, as well as accounting for inertial terms. Particular attention is paid to the effects of curing on the flow characteristics. In this regard, a kinetic reaction model is presented for simulating the curing of the healing agent and a set of relationships established for representing the variation of rheological properties with the degree of cure. Data obtained in a linked experimental programme of work are employed to justify the choice and form of the constitutive relationships, as well as to calibrate the model's evolution functions. Finally, a series of validation examples are presented that include the analysis of a series of concrete beam specimens with an embedded vascular network. These examples demonstrate the ability of the model to capture the transport behaviour of this type of SH cementitious material system.     

A density‐dependent elastoplastic hydro‐mechanical model for unsaturated compacted soils

This paper presents a three‐dimensional elastoplastic constitutive model for predicting the hydraulic and mechanical behaviour of unsaturated soils. It is based on experimental results obtained from a series of controlled‐suction triaxial tests on unsaturated compacted clay with different initial densities. Hydraulic hysteresis in the water‐retention behaviour is modelled as an elastoplastic process, with the elastic part modelled by a series of scanning curves and the elastoplastic part modelled by the main drying and wetting curves. The effect of void ratio on the water‐retention behaviour is studied using data obtained from controlled‐suction wetting–drying cyclic tests on unsaturated compacted clay with different initial densities. The effect of the degree of saturation on the stress–strain‐strength behaviour and the effect of void ratio on the water‐retention behaviour are considered in the model, as is the effect of suction on the hydraulic and mechanical behaviour. The initial density dependency of the compacted soil behaviour is modelled by experimental relationships between the initial density and the corresponding yield stress and, thereby, between the initial density and the normal compression line. The model is generalized to three‐dimensional stress states by assuming that the shapes of the failure and yield surfaces in the deviatoric stress plane are given by the Matsuoka–Nakai criterion. Model predictions of the stress–strain and water‐retention behaviour are compared with those obtained from triaxial tests with different initial densities under isotropic compression, triaxial compression and triaxial extension, with or without variation in suction. The comparisons indicate that the model accurately predicts the hydraulic and mechanical behaviour of unsaturated compacted soils with different initial densities using the same material constant. Copyright © 2006 John Wiley & Sons, Ltd.     

Experimental and numerical study of the damage process in RC beam-column sub-assemblages during a progressive collapse scenario

In the present paper, the collapse resistance of reinforced concrete (RC) beam-column sub-assemblages subjected to a middle column removal scenario is investigated on the basis of experimental tests and numerical calculations. For the experimental programme, three one-third scale substructures are designed with two types of longitudinal steel rebar to observe the influence of rebar detailing on the global structural behaviour. The structure under consideration is composed of a two-bay beam, and a middle column lies on two sliding-pin connections to prevent a catenary action mechanism. A digital image correlation (DIC) technique was employed with the experiments to observe the growth of cracks. In addition, numerical simulations using the finite element method (FEM) were also done. The Denoual-Forquin-Hild (DFH) anisotropic damage model is used to simulate the behaviour of the concrete, whereas a plasticity model is used for the steel rebars. The numerical simulations are compared with experimental data in terms of structural yield strength, change in stiffness and crack propagation, and better agreement is observed when a weakening of the concrete due to beam stirrups is taken into account.     

Modelling the elastic behaviour of granular materials

A review of the literature indicates that the elastic behaviour of granular materials is isotropic and that Poissony's ratio is constant, whereas Young's Modulus, the bulk modulus and the shear modulus vary with the mean normal stress and the deviatoric stress. A nonlinear, isotropic model for the elastic behaviour is developed on the basis of theoretical considerations involving the principle of conservation of energy. Energy is therefore neither generated not dissipated in closed-loop stress paths or in closed-loop strain paths. The framework for the model consists of Hooke's law, in which Poission's ratio is constant and Young's modulus is expressed as a power function invlving the first invariat of the stress tensor and the second invariant of the deviatoric stress tensor. The characteristics of the model are described, and the accuracy is evaluated by comparison with experimental results from triaxial tests and three-dimensional cubical triaxial tests with a variety of stress paths. Parameter determination from unloading–reloading cycles in conventional triaxial compression tests is demonstrated, typical parameter values are given for granular materials and extension of the model to soils with effective cohesion is described.     

Experimental study and constitutive modelling of elasto‐plastic damage in heat‐treated mortar

This study investigates the effect of a heat‐treatment upon the thermo‐mechanical behaviour of a model cement‐based material, i.e. a normalized mortar, with a (w/c) ratio of 0.5. First, a whole set of varied experimental results is provided, in order to either identify or validate a thermo‐mechanical constitutive model, presented in the second paper part. Experimental responses of both hydraulic and mechanical behaviour are given after different heating/cooling cycling levels (105, 200, 300, 400^°C). The reference state, used for comparison purposes, is taken after mass stabilization at 60^°C. Typical uniaxial compression tests are provided, and original triaxial deviatoric compressive test responses are also given. Hydraulic behaviour is identified simultaneously to triaxial deviatoric compressive loading through gas permeability K_gas assessment. K_gas is well correlated with volumetric strain evolution: gas permeability increases hugely when ε_v testifies of a dilatant material behaviour, instead of contractile from the test start. Finally, the thermo‐mechanical model, based on a thermodynamics approach, is identified using the experimental results on uniaxial and triaxial deviatoric compression. It is also positively validated at residual state for triaxial deviatoric compression, but also by using a different stress path in lateral extension, which is at the origin of noticeable plasticity. Copyright © 2009 John Wiley & Sons, Ltd.