循环荷载下粉土液化流动特性拖球试验研究

基于流体力学中的Stokes黏滞阻力理论,以振动台试验为基础,开发了一套测量液化过程中粉土流变特性的拖球试验装置。在铺有粉土海床的模型箱内埋设光滑小球,通过测量小球水平运动过程中所受阻力值的大小,计算粉土液化的表观动力黏度,分析粉土液化过程中的表观动力黏度与超孔压比之间的关系,以及液化后表观黏度与应变率的变化规律。试验结果表明,振动台试验下,孔隙压力表现为迅速上升,粉土迅速达到液化状态;振动过程对海床固结影响较大;粉土海床在未达到完全液化状态时（ru<1）,表观黏度随超孔压比增大而减小,在液化状态下（ru=1）,剪应力随应变率增大而减小,粉土呈现出剪切稀化的特点,为典型的非牛顿流体特征。     

低围压下埕北海域重塑粉土振动孔压模型试验研究

开展了低围压条件下固结不排水振动三轴实验,对埕北海域重塑粉土振动孔压发展模型进行研究。低围压条件下粉土孔压随振次的发展曲线呈现两种形态,具体呈现何种形态与粉土轴向动应力和临界循环应力有关。对孔压数据进行了归一化处理,发现低围压条件下粉土孔压模型可以用指数函数进行拟合,且黏土含量并不影响孔压模型形式,只会影响a、b两个实验参数。孔压影响因素分析表明,少量黏粒含量的加入可以使粉土的孔压发展速度增大;振动频率对粉土孔压发展的影响也存在一个临界值,约0.2 Hz,当振动频率小于该值时,粉土孔压增长速度随频率的增加而减缓;当振动频率大于该值时,粉土孔压增长的速度随频率的增加而增大。     

北部湾地区海砂填料的动力特性分析

为研究北部湾地区海砂填料的动力特性,采用高级动态三轴测试系统开展循环荷载下的动三轴试验,研究不同围压及不同动应力幅值对海砂动力特性的影响规律。试验结果表明：轴向累计应变随围压增加而减小,围压150 kPa时振次10 000后应变仅为3%;随着动应力幅值的增大轴向累积应变随之增大,且达到破坏标准的时间越短。动弹性模量随着动应力幅值和围压的增加而增大,不同围压下动弹性模量随动应变的增加出现先骤减再略减后稳定的发展趋势,ε_d>0.3%后开始趋于稳定;不同动应力幅值下动弹性模量出现先增后减直至稳定的趋势,其中动应力幅值对动弹性模量有明显的影响,围压影响相对较小。孔压比随动应力幅值增加而减小,随围压增加而增加。     

海洋粉质粘土在波浪荷载作用后的不排水抗剪强度衰化特性

通过对南海重塑粉质粘土土样的大量动三轴试验结果分析,得到此种土在波浪荷载作用后不捧水抗剪强度衰化同动载作用引起的动应变幅及平均累积孔压之间的相互关系和预估公式;并通过与超固结土样的静三轴剪切试验结果的比较,发现动、静三轴两种试验结果具有很好的吻合关系。建议可用超固结土样的静三轴剪切试验同时结合部分动三轴试验来预估土样在波浪荷载作用后不排水抗剪强度衰化与平均累积孔压之间的关系。     

不同粘粒含量粉质土的动力强度特性研究

通过室内实验研究了黄河三角洲地区粘粒质量分数为3%～15%的饱和粉土动力强度特性.使用动三轴施加轴向动力,测得试样在动荷载作用下达到破坏时所需的振动次数及破坏过程中孔隙水压力的变化情况.试验结果显示每一组试样在不同循环应力作用下饱和粉土的破坏振次随剪应力比的增加而减小.通过对比分析不同粘粒含量粉土动强度特征曲线,得出粉土动强度对粘粒含量有很大的依赖性,在一定粘粒含量范围内,粉土动强度随粘粒含量增加先减小后增大.     

杭州湾浅层粉土动力特性研究

选用杭州湾广泛分布的浅层粉土为研究对象,进行了一系列动三轴加载试验,研究了结构性、加载频率及动应力对杭州湾海底浅层粉土动应变、临界循环应力比和动强度的影响。试验结果表明,同一加载条件下,重塑样比原状样在更小振次内达到破坏,原状样动强度大于重塑样;结构性是影响土样动强度的重要因素,结构性对土样强度的影响随着动应力的增大而增强,随着频率的增大而减弱;加载频率的变化也对试样动力特性有较大影响,随着频率的增大,试样达到破坏所需振次加大,试样临界循环应力比也随之增大。     

饱和黏土的循环剪切变形特性

利用土工静力-动力液压三轴-扭转多功能剪切仪，针对饱和黏土，在不固结不排水（uu）条件下进行了应力控制式循环扭剪和竖向-扭转耦合试验，通过对试验结果的对比分析探讨了初始预剪应力和应力反向对应力-应变关系特性的影响。并阐述了不同循环应力模式下孔隙水压力发展特性。试验结果表明初始预剪应力对循环应力-应变关系的模式有明显的影响，当初始预剪应力较大且没有应力反向发生时，变形以累积效应为主，当初始剪应力为0时，变形以循环效应为主；不固结不排水条件下的循环孔隙水压力总是在围压附近波动，孔压的波动范围似乎随循环应力的增大而增大，但不具有孔压累积升高的特点。综合考虑剪切变形和正向偏差变形的共同效应，同时为了能够反映平均残余变形和循环变形的影响，建议了一个综合应变破坏标准的算式。进而通过利用试验数据与目前常用的应变标准比较，表明这种破坏标准具有普遍适用性和较好的稳定性，适用于判定各种应力条件下黏土试样破坏及其强度。     

黄河水下三角洲液化与未液化粉土的工程地质性质对比研究

以黄河水下三角洲埕岛海域海底粉土为研究对象,分析液化后重新固结粉土与未发生过液化粉土的工程地质性质差异,从浅地层剖面影像、土体的静力学参数、动力学参数、微结构特征等方面对比论述二者的不同,从而分析液化对粉土工程地质性质的改造作用。研究结果表明,粉土液化后层理结构消失,土体的主要静力学参数及动力学参数均增大,微结构特征表现为面孔隙比、圆形度及分形维数均减小,总体上土体液化固结后工程地质性质提高,若使液化过的粉土再次发生液化,需要更大的外动力条件才能实现。由于液化后粉土层理结构改变,细粒物质析出,颗粒重新排列,形成更加稳定的结构,从而强度随之增大。     

动荷载作用下海底粉土的孔压响应及其动强度

本文选用近海分布较广的粉土为研究对象 ,利用室内动三轴试验结果 ,找出动荷载作用下粉土的动应力应变关系 ,分析模拟波浪荷载作用下粉土中的孔压响应、临界循环次数 ,确定波浪作用下粉土的应力状态、破坏临界循环次数 ,判断不同深度处的粉土发生液化的可能性及发生液化所需要的时间 ;研究粉土在动荷载作用下的强度降低 ,为海上工程设计和施工提供科学依据。     

深海能源土含气储层力学特性三轴试验研究

为研究深海能源土在负压开采过程中含气储层的力学特性,基于含气土赋存理论,提出一种能够控制含气量及气泡大小的制样方法,通过GDS标准应力路径三轴试验系统,开展深海能源土含气储层的固结排水试验研究,分析深海能源土在不同黏土含量及不同含气量下的力学响应规律。研究结果表明：围压变化对深海能源土含气储层的抗剪强度峰值大小影响显著,围压越大抗剪强度峰值越高;黏土含量是决定应力应变曲线变化趋势的关键影响因素,黏土含量越高试样抗剪强度越低,试样抵抗应变软化效应的能力越强;含气土比饱和土体承载能力更低,且承载能力随含气量的增大呈衰减趋势;黏土含量和含气量是深海能源土含气储层抗剪强度指标的重要影响因素,黏土含量、含气量越高,土体自身的总抗剪强度值越低。     

Experimental study on the cyclic behavior of loose calcareous sand under linear stress paths

Abstract

Hollow cylinder torsional shear tests on loose isotropically and anisotropically consolidated calcareous sand were conducted to investigate the cyclic behavior under three different linear stress paths, including horizontal line, oblique line, and vertical line stress paths, in a coordinate system of the normal stress difference and the horizontal shear stress. The dominant strain components of the isotropically consolidated specimens are affected by the stress paths. With increasing consolidation stress ratio, axial strain gradually becomes the dominant strain component under the three different stress paths. The cyclic strength of the isotropically consolidated specimens under the three different stress paths are almost the same, while for the anisotropically consolidated specimens, the cyclic strengths are strongly affected by the stress paths. These results indicate that conventional cyclic triaxial tests may overestimate cyclic strength in some cases. Irrespective of the stress paths and cyclic stress ratios, the terminal residual excess pore pressure ratio decreases with increasing consolidation stress ratio. Moreover, an empirical equation is proposed to describe the relationship between the normalized shear work and the normalized residual excess pore pressure ratio. The comparative study reveals that the relationship proposed for silica sand is not suitable for the dynamic analyses of calcareous sand.     

Stiffness Degradation of Undisturbed Saturated Soft Clay in Yangtze Estuary under Complex Stress Conditions

Stiffness degradation will occur due to the generation of accumulated pore pressure in saturated soft clays under cyclic loading. The soil static-dynamic multi-purpose triaxial and torsional shear apparatus in Dalian University of Technology was employed to perform different types of test on saturated soft marine clay in the Yangtze estuary. Undisturbed samples of the clay were subjected to undrained cyclic vertical and torsional coupling shear and cyclic torsional shear after three-directional anisotorpic consolidation with different initial consolidation parameters. Investigated were the effects of the initial orientation angle of the major principal stress, initial ratio of deviatoric stress, initial coefficient of intermediate principal stress and continuous rotation of principal stress axes on the stiffness degradation. It is found that the degradation index decreases (or degradation degree increases) significantly with increasing initial orientation angle of the major principal stress and initial ratio of deviatoric stress. Compared to the effects of the initial orientation angle of the major principal stress and initial ratio of deviatoric stress, the effect of initial coefficient of intermediate principal stress is less evident and this trend is more clearly reflected by the results of the cyclic torsional shear tests than those of the cyclic coupling shear tests. At the same cycle number, the degradation index obtained from the cyclic torsional shear test is higher than that from the cyclic coupling shear test. The main reason is that the continuous rotation in principal stress directions during cyclic coupling shear damages the original structure of the soil more than the cyclic torsional shear does. Based on a series of experiments, a mathematical model for stiffness degradation is proposed and the relevant parameters are determined.     

Mechanical Behavior of Light-Weight Soil Under Consolidated Drained Shear Condition

To reveal the influence of material composition on mechanical properties of light-weight soil, stress-strain -volumetric strain characteristics and Poisson's ratio of mixed soil were researched by consolidated drained shear tests. The results show that light-weight soil is a kind of structural soil, so its mechanical properties are affected by mixed ratio and confining pressure, and mixed soil possesses structural yield stress. When confining pressure is less than the structural yield stress, strain softening occurs; when confining pressure is more than the structural yield stress, strain hardening is observed. There are two kinds of volume change behavior: shear contraction and shear dilatancy. Shear dilatancy usually leads to strain softening, but there isn't an assured causal relationship between them. Poisson's ratio of mixed soil is a variational state parameter with the change of stress state, it decreases with increased confining pressure, and it increases with increased stress level. When axial strain is near 5%, Poisson’ ratio is gradually close to a steady value. The main range of Poisson's ratio is 0.25～0.50 when confining pressure changes from 50 to 300 kPa. When unconfined compressive strength of mixed soil is less than 328 kPa, its stress-strain-volumetric strain characteristics can be predicted very well by Duncan-Chang model (E-B model). However, when the range of unconfined compressive strength is [328 kPa, 566 kPa], the model can't predict stress-strain characteristics accurately when confining pressure is under 200 kPa, and it also can't predict the strong shear dilatancy phenomenon of mixed soil under low confining pressure.     

Study on the shear property of nano-MgO-modified soil

To study the relationship between nano-MgO and soil shear property, the nano-MgO was evenly mixed in the soil to perform the triaxial consolidation draining shear test. Then the microscopic soil granules on the shear planes were observed through the scanning electron microscope. The soil water content was 10% and soil dry density was 1.5?g/cm³, different dosages of nano-MgO, i.e., 0, 2, 4, and 6% were put into the soil samples. The result of triaxial consolidation draining shear test showed that, under low confining pressure and more nano-MgO dosage, the stress–strain relationship of nano-MgO-modified soil turned from hardening to softening. The incorporation of nano-MgO can effectively improve the soil failure strength and cohesive force, and the increasing dosages of nano-MgO had a positive effect on soil shear strength and cohesive force, but little effect on internal friction angle. The analysis of scanning electron microscopy showed that the dosage of nano-MgO can reduce the void ratio of soil and reinforce the cementation between soil granules to change the shear property of soil.     

电阻率法监测黄河口海床沉积物固结过程现场试验研究

为了研究黄河口海床沉积物固结过程中电阻率同工程力学性质指标的对应关系,探索海床土体固结过程的新型原位监测技术,本文在黄河刁口流路三角洲叶瓣潮坪上,现场取土配置黄河口快速沉积形成的流体状沉积物和观测研究粉质土海床的固结过程。利用静力触探、十字板剪切试验、孔隙水压力监测等原位土工测试手段,实时测定固结过程中海床土强度变化和孔隙水压力消散过程;同时通过埋置自行研制的环形电极探杆,实时测定海床土固结过程中的电阻率变化。通过对比分析海床土电阻率与工程力学性质指标的同步测定数据发现:黄河口饱和粉土的电阻率与微型贯入试验测得的土体贯入强度,静力触探试验测得的比贯入阻力,十字板剪切试验测得的不排水抗剪强度(峰值强度、残余强度)均呈乘幂关系,且相关性良好;海床沉积物在固结过程中的电阻率与孔隙水压力呈负线性相关性。     

Effect of Cyclic Loading Frequency on Undrained Behaviors of Undisturbed Marine Clay

Based on a series of cyclic triaxial tests, the effect of cyclic frequency on the undrained behaviors of undisturbed marine clay is investigated. For a given dynamic stress ratio, the accumulated pore water pressure and dynamic strain increase with the number of cycles. There exists a threshold value for beth the accumulated pore water pressure and dynamic strain, below which the effect of cyclic frequency is very small, but above which the accumulated pore water pressure and dynamic strain increase intensely with the decrease of cyclic frequency for a given number of cycles. The dynamic strength increases with the increase of cyclic frequency, whereas the effect of cyclic frequency on it gradually diminishes to zero when the number of cycles is large enough, and the dynamic strengths at different frequencies tend to the same limiting minimum dynamic strength. The test results demonstrate that the reasons for the frequency effect on the undrained soil behaviors are beth the creep effect induced by the loading rate and the decrease of sample effective confining pressure caused by the accumulated pore water pressure.     

Characteristics of Pore Water Pressure of Saturated Silt Under Wave Loading

The characteristics of dynamic stress in the seabed under wave loading are constant principal stress and continuous rotation of the principal stress direction.Cyclic triaxial-torsional coupling shear tests were performed on saturated silt by the hollow cylinder apparatus under different relative densities,deviator stress ratios and vibration frequencies to study the development of pore water pressure of the saturated silt under wave loading.It was found that the development of pore water pressure follows the trend of "fast～steady～drastic".The turning point from fast to steady stage is not affected by relative density and deviator stress ratio.However,the turning point from steady to drastic stage relies on relative density and deviator stress ratio.The vibration cycle for the liquefaction of saturated silt decreases with increasing deviator stress ratio and increases with relative density.The vibration cycle for the liquefaction of the saturated silt increases with vibration frequency and reaches a peak value,after which it decreases with increasing vibration frequency for the relative density of 70%.But the vibration cycle for the liquefaction of saturated silt increases with vibration frequency for the relative density of 30%.The development of pore water pressure of the saturated silt is influenced by relative density and vibration frequency.     

Comparison Between Shear Behaviors of Overconsolidated Nakdong River Sandy Silt and Silty Sand

From this research, overconsolidated undrained and drained behaviors of specimens with high sand content were highly dilatant. According to the comparison results of laboratory tests, the deviator stresses of silty sand were greater than sandy silt due to high sand content under increasing OCRs, and both silty sand and sandy silt were presented strain softening tendency after failure under undrained loading. The pore water pressure increased with increasing fines content under increasing OCRs. Silty sand exhibited more dilatancy and increasing shear strength than sandy silt because pore water pressures of silty sand were lower than sandy silt under higher OCRs. In overconsolidated drained tests, silty sand is higher strength than sandy silt because silty sand has a lower volumetric strain and higher deviator stress than sandy silt under increasing OCRs. As the degree of overconsolidation increased, similar behaviors of silty sand and sandy silt observed that volumetric strain decreased to negative values due to dilatancy effect and low-cohesion under current effective confining pressures.     

Monotonic and cyclic behaviors of loose anisotropically consolidated calcareous sand in torsional shear tests

ABSTRACT

The behavior of loose anisotropically consolidated calcareous sand obtained from an island in the South China Sea was investigated under undrained monotonic and cyclic loading in a hollow cylinder torsional apparatus. The tests were conducted on specimens which consolidated under various initial effective confining pressures and consolidation stress ratios. The monotonic test results show that the failure and phase transformation line are essentially independent of the consolidation conditions, while the initial contractive tendency of the specimens decreases with an increasing consolidation stress ratio. During monotonic loading of the anisotropically consolidated specimens, a same major principal stress direction is observed at the constant stress ratio lines up to the phase transformation line, irrespective of initial effective confining pressure. The cyclic strength of the sand increases with an increasing consolidation stress ratio. Moreover, a pronounced stress dependence is observed in the sand with higher consolidation stress ratio. During cyclic loading, the generated excess pore water pressure presents considerable fluctuations. The normalized terminal excess pore water pressure is described as a function of consolidation stress ratio. The tests show that the particle shape, rather than particle crushing, plays an important role in the monotonic and cyclic behaviors of the calcareous sand.