In-Line Measurement of Trichloroethylene Vapors Using Tin Dioxide Sensors

During thermally enhanced in situ remediation of soils and ground water, gas streams are generated with varying temperatures, moisture content, and organic compound concentrations. In this study, we evaluated the performance of tin dioxide sensors for measuring trichloroethylene (TCE) concentrations in gas streams from a thermally enhanced soil vapor extraction system. Temperature, pressure, moisture content, and vapor flow rates affected the resistivity of the sensors, and thus the signal. When fluctuations in these parameters were eliminated by condensing excess water and healing to a constant temperature prior to measurement, the sensors provided reliable in-line measurement of TCE concentrations. Gas tracers such as methane were easily monitored in-line, providing quick and inexpensive data on subsurface vapor flow velocities and direction.     

Demonstration of Enhanced Bioremediation in a TCE Source Area at Launch Complex 34, Cape Canaveral Air Force Station

The ability of bioremediation to treat a source area containing trichloroethene (TCE) present as dense nonaqueous phase liquid (DNAPL) was assessed through a laboratory study and a pilot test at Launch Complex 34, Cape Canaveral Air Force Center. The results of microcosm testing indicate that the indigenous microbial community was capable of dechlorinating TCE to ethene if amended with electron donor; however, bioaugmentation with a dechlorinating culture (KB-1; SiREM, Guelph, Ontario, Canada) significantly increased the rate of ethene formation. In microcosms, the activity of the dechlorinating organisms in KB-1 was not inhibited at initial TCE concentrations as high as 2 mM. The initially high TCE concentration in ground water (1.2 mM or 155 mg/L) did not inhibit reductive dechlorination, and at the end of the study, the average concentration of ethene (2.4 mM or 67 mg/L) was in stoichiometric excess of this initial TCE concentration. The production of ethene in stoichiometric excess in comparison to the initial TCE concentration indicates that the bioremediation treatment enhanced the removal of TCE mass (either sorbed to soil or present as DNAPL). Detailed soil sampling indicated that the bioremediation treatment removed greater than 98.5% of the initial TCE mass. Confirmatory ground water samples collected 22 months after the bioremediation treatment indicated that chloroethene concentrations had continued to decline in the absence of further electron donor addition. The results of this study confirm that dechlorination to ethene can proceed at the high TCE concentrations often encountered in source areas and that bioremediation was capable of removing significant TCE mass from the test plot, suggesting that enhanced bioremediation is a potentially viable remediation technology for TCE source areas. Dehalococcoides abundance increased by 2 orders of magnitude following biostimulation and bioaugmentation.     

Removal of Volatile Organic Compounds from Surfactant Solutions by Flash Vacuum Stripping in a Packed Column

Volatile organic compounds (VOCs) am be removed from contaminated ground water and subsurface media by surfaclant-enhanced remediation processes. For the process to be economically competitive it is necessary to recover and reuse the surfactant from this concentrated solution. The VOC can be removed from this concentrated solution by flash vacuum stripping, leaving the surfactant solution for reuse. In this study, the flash vacuum stripping of trichloroethylene (TCE) from an anionic surfactant solution in a co-current packed column was studied under rough vacuum conditions. The presence of surfactants lead to a reduction in the overall liquid phase volumetric mass transfer coefficient (MTC) of 40 to 95%. depending on flow rate and surfactant concentration at 50°C and 16 kPa. At liquid loading rates of less than 13 cm³/cm²min, the MTC of TCE decreases rapidly with an increase in liquid loading rate, and at liquid loading rates above that, the MTC decreases slightly with an increase in the liquid loading rate. This trend may have been due to foaming. At surfactant concentrations above the critical micelle concentration, the effect of surfactant concentration was not significant at liquid loading rates less than 13 cm³/cm²min. However, beyond that rate, the MTC of TCE decreased drastically with an increase in surfactant concentration. The MTC of TCE increased with an increase in temperature. A large pressure drop (3 to 4 kPa/m) was observed across the packed bed due to foaming.     

Improving Risk-Based Screening at Vapor Intrusion Sites in California

The attenuation factor (AF) of 0.03 recommended by the U.S. Environmental Protection Agency (USEPA) is increasingly being used by regulatory agencies for the development of subsurface vapor screening levels for vapor intrusion (VI). There are concerns, however, over the database used to derive the AF and the AF's applicability to building types and geographies not included in USEPA database. To derive a more technically defensible AF for subsurface vapor screening in California, a database consisting of 8415 paired indoor and subsurface vapor samples collected from 485 buildings at 36 sites in California was compiled. Filtering was applied to remove data of suspect quality that were potentially affected by background (non-VI) sources. Filtering reduced the size of the database to 788 indoor air and subsurface vapor pairs, 80% of which were trichloroethylene (TCE) measurements. An AF of 0.0008 was derived from only TCE vapor data, based on the ability of the AF to reliably identify buildings with indoor air concentrations above screening levels in 95% of cases where subsurface vapor screening levels were exceeded. The AF derived from this study demonstrated limited sensitivity to the variables typically considered important in VI characterization, which was partially attributed to relatively weak correlation of indoor air and subsurface vapor concentration data. The results of this study can be used to improve VI screening in California and other states and help focus limited resources on sites posing the greatest potential risk.     

Effect of NAPL Source Morphology on Mass Transfer in the Vadose Zone

The generation of vapor‐phase contaminant plumes within the vadose zone is of interest for contaminated site management. Therefore, it is important to understand vapor sources such as non‐aqueous‐phase liquids (NAPLs) and processes that govern their volatilization. The distribution of NAPL, gas, and water phases within a source zone is expected to influence the rate of volatilization. However, the effect of this distribution morphology on volatilization has not been thoroughly quantified. Because field quantification of NAPL volatilization is often infeasible, a controlled laboratory experiment was conducted in a two‐dimensional tank (28 cm × 15.5 cm × 2.5 cm) with water‐wet sandy media and an emplaced trichloroethylene (TCE) source. The source was emplaced in two configurations to represent morphologies encountered in field settings: (1) NAPL pools directly exposed to the air phase and (2) NAPLs trapped in water‐saturated zones that were occluded from the air phase. Airflow was passed through the tank and effluent concentrations of TCE were quantified. Models were used to analyze results, which indicated that mass transfer from directly exposed NAPL was fast and controlled by advective‐dispersive‐diffusive transport in the gas phase. However, sources occluded by pore water showed strong rate limitations and slower effective mass transfer. This difference is explained by diffusional resistance within the aqueous phase. Results demonstrate that vapor generation rates from a NAPL source will be influenced by the soil water content distribution within the source. The implications of the NAPL morphology on volatilization in the context of a dynamic water table or climate are discussed.     

Influence of Fluctuating Groundwater Table on Volatile Organic Chemical Emission Flux at a Dissolved Chlorinated-Solvent Plume Site

Groundwater elevation fluctuation has been recognized as one mechanism causing temporal indoor air volatile organic chemical (VOC) impacts in vapor intrusion risk assessment guidance. For dissolved VOC sources, groundwater table fluctuation shortens/lengthens the transport pathway, and delivers dissolved contaminants to soils that are alternating between water saturated and variably saturated conditions, thereby enhancing volatilization potential. To date, this mechanism has not been assessed with field data, but enhanced VOC emission flux has been observed in lab-scale and modeling studies. This work evaluates the impact of groundwater elevation changes on VOC emission flux from a dissolved VOC plume into a house, supplemented with modeling results for cyclic groundwater elevation changes. Indoor air concentrations, air exchange rates, and depth to groundwater (DTW) were collected at the study house during an 86-d constant building underpressurization test. These data were used to calculate changes in trichloroethylene (TCE) emission flux to indoor air, during a period when DTW varied daily and seasonally from about 3.1 to 3.4 m below the building foundation (BF). Overall, TCE flux to indoor air varied by about 50% of the average, without any clear correlation to changes in DTW or its change rate. To complement the field study, TCE surface emission fluxes were simulated using a one-dimensional model (HYDRUS 1D) for conditions similar to the field site. Simulation results showed time-averaged surface TCE fluxes for cyclic water-table elevations were greater than for stationary water-table conditions at an equivalent time-averaged water-table position. The magnitudes of temporal TCE emission flux changes were generally less than 50% of the time-averaged flux, consistent with the field site observations. Simulation results also suggested that TCE emission flux changes due to groundwater fluctuation are likely to be significant at sites with shallow groundwater (e.g., < 0.5 m BF) and permeable soil types (e.g., sand).     

Modeling Volatile Chemical Transport, Biodecay, and Emission to Indoor Air

A model is presented for estimating vapor concentrations in buildings because of volatilization from soil contaminated by non- aqueous phase liquids (NAPL) or from dissolved contaminants in ground water. The model considers source depletion, diffusive- dispersive transport of the contaminant of concern (COC) and of oxygen and oxygen-limited COC biodecay. Diffusive-advective transport through foundations and vapor losses caused by foundation cross-flow are considered. Competitive oxygen use by various species is assumed to be proportional to the product of the average dissolved-phase species concentration and a biopreference factor. Laboratory and field data indicate the biopreference factor to be proportional to the organic carbon partition coefficient for the fuel hydrocarbons studied. Predicted indoor air concentrations were sensitive to soil type and subbase permeability. Lower concentrations were predicted for buildings with shallow foundations caused by flushing of contaminants by cross-flow. NAPL source depletion had a large impact on average exposure concentration. Barometric pumping had a minor effect on indoor air emissions for the conditions studied. Risk-based soil cleanup levels were much lower when biodecay was considered because of the existence of a threshold source concentration below which no emissions occur. Computed cleanup levels at NAPL-contaminated sites were strongly dependent on total petroleum hydrocarbon (TPH) content and COC soil concentration. The model was applied to two field sites with gasoline-contaminated ground water. Confidence limits of predicted indoor air concentrations spanned approximately two orders of magnitude considering uncertainty in model parameters. Measured contaminant concentrations in indoor air were within model-predicted confidence limits.     

Impact of Turbidity on TCE and Degradation Products in Ground Water

Elevated particulate concentrations in ground water samples can bias contaminant concentration data. This has been particularly problematic for metal analyses where artificially increased turbidity levels can affect metals concentrations and confound interpretation of the data. However, few studies have been conducted to determine the impact of particulates on trichloroethylene (TCE), cis-dichloroethylene (c-DCE), and vinyl chloride concentrations.
Laboratory batch studies and field investigations were conducted to evaluate the effects of suspended solids on VOC concentrations in ground water samples analyzed by purge-and-trap gas chromatography. Three different solids were used to assess the effects of suspended particulates. The solids were aquifer material from a field site in North Carolina and two reference clay minerals (kaolinite and Namontimorillonite). During the laboratory portion of this study, the solids were used to determine effects on TCE concentrations under controlled laboratory conditions.
The same solids were used in a field study to compare the laboratory results with field results. Solids were added to the sample vials prior it) sample collection to intentionally increase turbidity levels in the water samples. Results of the study indicate essentially no decrease in TCE, c-DCH, or vinyl chloride concentrations due to increased turbidity levels.     

Emissions of Trichloroethylene from Bedroom Furniture Set as a Source of Indoor Air Contamination

Shallow trichloroethene (TCE) groundwater and soil contamination associated with a Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) Superfund Site in Michigan resulted in a vapor intrusion (VI) investigation of overlying condominium units. Units with data suggesting a complete VI pathway received subslab depressurization systems (SSDs). Performance monitoring following the installation of an SSD at one unit indicated that the indoor air TCE concentrations remained elevated, despite pressure field extension tests that showed the system should effectively reduce VI from soil gas. Therefore, a cost-efficient and incremental investigation was launched to identify other potential source(s) of TCE using a field-portable gas chromatograph/mass spectrometer (GS/MS). The combination of room-by-room air sampling, potential VI entry point sampling, and emission tests of potential sources were used, which resulted in successfully identifying a bedroom furniture set as an indoor source of TCE for the unit. Although many common household products are recognized as indoor sources of TCE, emissions from finished furniture products have not been widely discussed in the VI literature. The findings of this study indicate that off gassing from furniture can lead to TCE concentrations in indoor air that exceed regulatory guidelines.     

Vertical cross contamination of trichloroethylene in a borehole in fractured sandstone

Boreholes drilled through contaminated zones in fractured rock create the potential for vertical movement of contaminated ground water between fractures. The usual assumption is that purging eliminates cross contamination; however, the results of a field study conducted in a trichloroethylene (TCE) plume in fractured sandstone with a mean matrix porosity of 13% demonstrates that matrix-diffusion effects can be strong and persistent. A deep borehole was drilled to 110 m below ground surface (mbgs) near a shallow bedrock well containing high TCE concentrations. The borehole was cored continuously to collect closely spaced samples of rock for analysis of TCE concentrations. Geophysical logging and flowmetering were conducted in the open borehole, and a removable multilevel monitoring system was installed to provide hydraulic-head and ground water samples from discrete fracture zones. The borehole was later reamed to complete a well screened from 89 to 100 mbgs; persistent TCE concentrations at this depth ranged from 2100 to 33,000 microg/L. Rock-core analyses, combined with the other types of borehole information, show that nearly all of this deep contamination was due to the lingering effects of the downward flow of dissolved TCE from shallower depths during the few days of open-hole conditions that existed prior to installation of the multilevel system. This study demonstrates that transfer of contaminant mass to the matrix by diffusion can cause severe cross contamination effects in sedimentary rocks, but these effects generally are not identified from information normally obtained in fractured-rock investigations, resulting in potential misinterpretation of site conditions.     

The use of surface-enhanced Raman scattering (SERS) for detection of PAHs in the Gulf of Gdańsk (Baltic Sea)

A field operable surface enhanced Raman scattering (SERS) sensor system was applied for the first time under real conditions for the detection of polycyclic aromatic hydrocarbons (PAHs) as markers for petroleum hydrocarbons in the Gulf of Gdańsk (Baltic Sea). At six stations, seawater samples were taken, and the sensor system was applied in situ simultaneously. These measurements were compared to the results of conventional GC/MS laboratory analysis of the PAH concentrations in the seawater samples. For a PAH concentration above 150 ng(12PAH)l(-1), there was agreement between the SERS sensor and the GC/MS determinations. A standard addition experiment yielded a PAH concentration of 900 ng l(-1) at the Gdańsk Harbor, which was of the same order as the GC/MS determinations of 12PAHs (200 ng(12PAH)l(-1)). The high SERS detection limit for seawater samples is explained by the competition for PAHs between the sensor membrane and particulate matter surfaces. Thus, the SERS sensor can be applied, e.g., as a non-quantitative alarm sensor for relatively high PAH concentrations in heavily polluted waters. The spectral unmixing procedure applied for Gdańsk Harbor water confirmed the presence of phenanthrene at the highest concentration ([Phe]=140 ngl(-1)) and of Chr (2.7 ng l(-1)), but it did not detect the other PAHs present in the Gdańsk Harbor water, as determined by GC/MS. When compared to the past literature and databases, the SERS spectra indicated the presence of a mixture of molecules consisting of carotenoids, n-alkanes, amines or fatty acids, and benzimidazoles at the coastal station ZN2. The spectra in the offshore direction indicated carboxylic acids. Interpretation of the farthest offshore in situ SERS measurements is difficult, principally due to the limited availability of reference spectra. The detection of the lower PAH concentrations commonly found in Baltic coastal water needs further research and development to obtain better sensitivity of the SERS sensor. However, the high analytical specificity of the SERS sensor also allows the detection of other chemical species that require the development of a SERS/Raman library for specific in situ spectral interpretation.     

Removal of PCE DNAPL from Tight Clays Using In Situ Thermal Desorption

This paper presents a full‐scale thermal remediation of a brownfields site near San Francisco, California. In Situ Thermal Desorption (ISTD) was used for treatment of chlorinated solvents in a tight clay below the water table. The site had contaminants in concentrations indicating that a tetrachloroethene (PCE)‐rich DNAPL was present. A target volume of 5097 m³ of subsurface material to a depth of 6.2 m was treated for a period of 110 d of heating. Energy was delivered through 126 thermal conduction heater borings, and vapors were extracted from a combination of vertical and horizontal vacuum wells. Approximately 2540 kg of contaminants were recovered in the extracted vapors by the end of treatment. The PCE concentration in the clay was reduced from as high as 2700 mg/kg to an average concentration of 0.012 mg/kg within 110 d of heating (a reduction of >99.999%). Similar effectiveness was documented for TCE, cis‐1,2‐DCE, and vinyl chloride. A total of 2.2 million kWh of electric power was used to heat the site. Approximately 45% of this energy was used to heat the subsurface to the target temperature. Another 53% was necessary to boil approximately 41% of the groundwater within the treatment zone, creating approximately 600 pore volumes of steam by the end of the 110‐d heating and treatment period. Steam generation thus occurred within the clay. Partitioning of the contaminants into the steam and its removal comprised the dominant remedial mechanism. The steam migrated laterally toward the ISTD heaters, where it encountered a small dry region adjacent to each of the heaters, which served as a preferential pathway allowing the steam to migrate upward along the heaters to the more permeable vadose zone. There the steam was captured by a system of vertical and horizontal vacuum extraction wells. This vapor removal strategy facilitated effective thermal treatment of the tight clays located below the water table. Features of a robust design are extension of the heaters at least 1.2 m deeper than the treatment depth, and the installation of shallow horizontal vapor collection wells which allow for establishment of pneumatic control.     

Mass and flux distributions from DNAPL zones in sandy aquifers

At three industrial sites in Ontario, New Hampshire, and Florida, tetrachloroethylene (PCE) and trichloroethylene (TCE), released decades ago as dense nonaqueous phase liquids (DNAPLs), now form persistent source zones for dissolved contaminant plumes. These zones are suspended below the water table and above the bottoms of their respective, moderately homogeneous, unconfined sandy aquifers. Exceptionally detailed, depth-discrete, ground water sampling was performed using a direct-push sampler along cross sections of the dissolved-phase plumes, immediately downgradient of these DNAPL source zones. The total plume PCE or TCE mass-discharge through each cross section ranged between 15 and 31 kg/year. Vertical ground water sample spacing as small as 15 cm and lateral spacing typically between 1 and 3 m revealed small zones where maximum concentrations were between 1% and 61% of solubility. These local maxima are surrounded by much lower concentration zones. A spacing no larger than 15 to 30 cm was needed at some locations to identify high concentration zones, and aqueous VOC concentrations varied as much as four orders of magnitude across 30 cm vertical intervals. High-resolution sampling at these sites showed that three-quarters of the mass-discharge occurs within 5% to 10% of the plume cross sectional areas. The extreme spatial variability of the mass-discharge occurs even though the sand aquifers are nearly hydraulically homogeneous. Depth-discrete field techniques such as those used in this study are essential for finding the small zones producing most of the mass-discharge, which is important for assessing natural attenuation and designing remedial options.     

Injection of Zero‐Valent Iron into an Unconfined Aquifer Using Shear‐Thinning Fluids

Approximately 190 kg of 2 μm‐diameter zero‐valent iron (ZVI) particles were injected into a test zone in the top 2 m of an unconfined aquifer within a trichloroethene (TCE) source area. A shear‐thinning fluid was used to enhance ZVI delivery in the subsurface to a radial distance of up to 4 m from a single injection well. The ZVI particles were mixed in‐line with the injection water, shear‐thinning fluid, and a low concentration of surfactant. ZVI was observed at each of the seven monitoring wells within the targeted radius of influence during injection. Additionally, all wells within the targeted zone showed low TCE concentrations and primarily dechlorination products present 44 d after injection. These results suggest that ZVI can be directly injected into an aquifer with shear‐thinning fluids to induce dechlorination and extends the applicability of ZVI to situations where other emplacement methods may not be viable.     

Laboratory Study of Air Sparging of TCE-Contaminated Saturated Soils and Ground Water

Air sparging has proven to be an effective remediation technique for treating saturated soils and ground water contaminated by volatile organic compounds (VOCs). Since little is known about the system variables and mass transfer mechanisms important to air sparging, several researchers have recently performed laboratory investigations to study such issues. This paper presents the results of column experiments performed to investigate the behavior of dense nonaqueous phase liquids (DNAPFs). specifically trichloroethylene (TCE), during air sparging. The specific objectives of the study were (1) to compare the removal of dissolved TCE with the removal of dissolved light nonaqueous phase liquids (LNAPLs). such as benzene or toluene; (2) to determine the effect of injected air-flow rate on dissolved TCE removal; (3) to determine the effect of initial dissolved TCE concentration on removal efficiency; and (4) to determine the differences in removal between dissolved and pure-phase TCE. The test results showed that (1) the removal of dissolved TCE was similar to that of dissolved LNAPL: (2) increased air-injection rates led to increased TCE removal at lower ranges of air injection, but further increases at higher ranges of air injection did not increase the rate of removal, indicating a threshold removal rate had been reached; (3) increased initial concentration of dissolved TCE resulted in similar rates of removal: and (4) the removal of pure-phase TCE was difficult using a low air-injection rate, but higher air-injection rates led to easier removal.     

Numerical simulation of transport and sequential biodegradation of chlorinated aliphatic hydrocarbons using CHAIN_2D

Microbiological degradation of perchloroethylene (PCE) under anaerobic conditions follows a series of chain reactions, in which, sequentially, trichloroethylene (TCE), cis‐dichloroethylene (c‐DCE), vinylchloride (VC) and ethene are generated. First‐order degradation rate constants, partitioning coefficients and mass exchange rates for PCE, TCE, c‐DCE and VC were compiled from the literature. The parameters were used in a case study of pump‐and‐treat remediation of a PCE‐contaminated site near Tilburg, The Netherlands. Transport, non‐equilibrium sorption and biodegradation chain processes at the site were simulated using the CHAIN_2D code without further calibration. The modelled PCE compared reasonably well with observed PCE concentrations in the pumped water. We also performed a scenario analysis by applying several increased reductive dechlorination rates, reflecting different degradation conditions (e.g. addition of yeast extract and citrate). The scenario analysis predicted considerably higher concentrations of the degradation products as a result of enhanced reductive dechlorination of PCE. The predicted levels of the very toxic compound VC were now an order of magnitude above the maximum permissible concentration levels. Copyright © 1999 John Wiley & Sons, Ltd.     

A Tracer Test to Characterize Treatment of TCE in a Permeable Reactive Barrier

A tracer test was conducted to characterize the flow of groundwater across a permeable reactive barrier constructed with plant mulch (a biowall) at the OU‐1 site on Altus Air Force Base, Oklahoma. This biowall is intended to intercept and treat groundwater contaminated by trichloroethylene (TCE) in a shallow aquifer. The biowall is 139‐m long, 7.3‐m deep, and 0.5‐m wide. Bromide was injected from an upgradient well into the groundwater as a conservative tracer, and was subsequently observed breaking through in monitoring wells within and downgradient of the biowall. The bromide breakthrough data demonstrate that groundwater entering the biowall migrated across it, following the slope of the local groundwater surface. The average seepage velocity of groundwater was approximately 0.06 m/d. On the basis of the Darcy velocity of groundwater and geometry of the biowall, the average residence time of groundwater in the biowall was estimated at 10 d. Assuming all TCE removal occurred in the biowall, the reduction in TCE concentrations in groundwater across the biowall corresponds to a first‐order attenuation rate constant in the range of 0.38 to 0.15 per d. As an independent estimate of the degradation rate constant, STANMOD software was used to fit curves through data on the breakthrough of bromide and TCE in selected wells downgradient of the injection wells. Best fits to the data required a first‐order degradation rate constant for TCE removal in the range of 0.13 to 0.17 per d. The approach used in this study provides an objective evaluation of the remedial performance of the biowall that can provide a basis for design of other biowalls that are intended to remediate TCE‐contaminated groundwater.     

Application of VLEACH to Vadose Zone Transport of VOCs at an Arizona Superfund Site

Cleanup standards for volatile organic compounds in thick vadose zones can be based on indirect risk (transport to ground water) when contamination is below depths of significant direct risk. At one Arizona Superfund site, a one-dimensional vadose zone transport model (VLE-ACH) was used to estimate the continued transport of VOCs from the vadose zone to ground water. VLEACH is a relatively simple and readily available model that proved useful for estimating indirect risk from VOCs in the vadose zone at this site. The estimates of total soil concentrations used as initial conditions for VLF.ACH incorporated a variety of data from the site. Soil gas concentrations were found to be more useful than soil matrix data for estimating total soil concentrations at this arid-zone site. A simple mixing cell model was used with the VLEACH-derived mass loading estimates from the vadose zone over time to estimate the resulting changes in ground water concentrations. For this site, the results of the linked VLEACH/mixing cell simulations indicate it is likely that the federal MCI. for TCE will be exceeded in underlying ground water if remedial action on I he vadose zone is not pursued.     

Evidence for Increasing Indoor Sources of 1,2-Dichloroethane Since 2004 at Two Colorado Residential Vapor Intrusion Sites

Groundwater contamination associated with two former industrial facilities in Denver, Colorado, has led to concerns about vapor intrusion into residences adjacent to the facilities. 1,1,1-Trichloroethane (1,1,1-TCA), 1,1-dichloroethene (1,1-DCE), and trichloroethene (TCE) are the main contaminants of concern in groundwater, with trace levels of 1,2-dichloroethane (1,2-DCA) present at one of the sites. Indoor air monitoring programs have been ongoing at these two sites since 1998 and recent results have suggested that background, indoor source, 1,2-DCA has been increasing in the frequency of detection, and median and maximum concentration over the past several years. A lines of evidence evaluation was undertaken for both sites in order to document the predominance of indoor sources of 1,2-DCA. Evidence utilized included spatial evaluation of 1,2-DCA in indoor air; comparison of 1,2-DCA concentrations in mitigated and unmitigated homes; a phone survey to evaluate the potential for smoking to contribute to indoor air 1,2-DCA levels; evaluation of mitigation system effluent data; and an evaluation of volatile organic compound (VOC) ratios in groundwater and indoor air. The results of this evaluation indicated that smoking had no demonstrable influence on measured indoor air concentrations. In addition, it appears that consumer products have had a markedly increased influence on indoor air concentrations since 2005. Data from one of the industrial facilities at one of the sites also indicated that polyvinyl chloride (PVC) and vinyl composite floor adhesive used in a building remodel in 2005 apparently generated elevated levels of indoor 1,2-DCA and vinyl chloride, which have been sustained up to the present time.     

Chloroethene Biotransformation in the Presence of Different Sulfate Concentrations

This paper aims to reconcile discrepancies among reports of dechlorination performance in the presence of sulfate, by analyzing data from the literature, presenting results from laboratory experiments performed with mixed anaerobic microbial cultures, and synthesizing respective findings. A complete set of metrics for dechlorination progress was developed and used in the analysis of selected field and laboratory studies. When differences in site and experimental conditions are accounted for and definitions of dechlorination completeness are harmonized, the inverse relationship between dechlorination performance and sulfate concentration becomes clearer. This relationship was investigated in detail with laboratory experiments on mixed anaerobic microbial cultures enriched with the same concentration of trichloroethylene (TCE) and different sulfate concentrations, equal to near zero (considered as the baseline culture), 30, 400, and 1100 mg/L. In all experiments, sulfate reduction proceeded concurrently with dechlorination. The observed behavior was bimodal, indicating a transition in dechlorination performance between 30 and 400 mg/L. Under low donor to acceptor stoichiometry conditions, TCE dechlorination was incomplete in all experiments after 14 days, while the percentage of TCE moles reduced to vinyl chloride was lower by about 50% in the experiments with high sulfate concentrations. When donor was added in excess to stoichiometry needs for TCE reduction, TCE dechlorination was complete in the baseline culture, while only little ethene was detected in the high sulfate concentration cultures. When all studies are considered together, it appears that the presence of sulfate does not preclude complete dechlorination but rather delays it. Data analysis also suggests that the proposed upper limit of 500 mg/L for the range of initial sulfate concentration that is not problematic for dechlorination should be revised to a lower value.