碳纤维布增强混凝土框架抗震性能的有限元分析

利用碳纤维布（CFS）对一个9层钢筋混凝土框架的底层柱进行了加固,运用有限元程序对加固前后结构的整体抗震性能进行了动力分析.分析结果表明,利用碳纤维布加固底部框架柱有助于提高框架的整体抗震性能,从而减少框架在地震作用下的最大侧移和各层间位移.     

屈曲约束支撑半刚性连接框架弹塑性地震位移简化计算

研究屈曲约束支撑半刚性连接框架弹塑性位移计算方法,为这种结构抗震设计提供依据.推导了屈曲约束支撑半刚性连接框架结构侧移刚度计算方法,通过计算屈曲约束支撑和半刚性连接在罕遇地震作用下的有效阻尼比,修正弹性设计反应谱,再利用修正后的设计反应谱进行结构弹塑性层间位移简化计算.通过与弹塑性时程分析对提出的计算方法进行验证.基于有效阻尼比的思想给出的弹塑性位移的简化计算方法可进行屈曲约束支撑半刚性连接框架罕遇地震下的抗震设计.     

钢框架结构直接基于位移的抗震设计方法研究

将钢框架结构按其性能划分为使用良好、人身安全、防止倒塌三个水平,并用层间侧移角予以量化采用钢框架的最大层侧移模式来确定其目标侧移曲线在等效线性化的前提下,由等效位移用弹性位移反应谱求出等效周期,然后对构件进行刚度设计和承载力设计用静力弹塑性分析方法对结构进行分析,校核其实际侧移曲线与满足性能目标的侧移曲线是否一致.采用...     

采用非线性纤维梁单元法的钢管混凝土组合框架动力响应分析

钢管混凝土结构已经广泛应用于我国高层和超高层建筑中,为研究该类结构的抗震性能,分别采用分离模量法和统一模量法对某13层钢管混凝土框架结构进行抗震性能分析,研究不同地震波作用下组合框架的模态和多遇地震下的弹性动力时程,对比组合框架顶点位移反应、加速度反应、层间侧移及动力放大系数等。研究结果表明,分离模量法和统一模量法建模方法在分析钢管混凝土框架抗震动力特性上总体相差不大,但前者可以考虑材料弹塑性,从而对结构弹塑性进行分析,而后者在弹塑性阶段需要用全曲线表达式,尚需进一步的研究。     

填充墙对底框结构地震反应的影响

为研究填充墙对底层框架多层砌体房屋地震反应的影响,以典型的填充墙-底层框架多层砌体房屋为基础,建立有限元计算模型并进行了弹塑性动力时程分析。根据不同模型的计算结果以及填充墙的刚度和强度,分析了填充墙对底层框架多层砌体房屋自振周期、地震作用下房屋整体变形、底层框架的损伤以及填充墙与底层框架相互作用的影响。计算结果表明：填充墙对房屋整体地震反应产生明显影响,其影响不能忽略。在上部砌体结构质量和刚度不变的情况下,结构自振周期随着填充墙刚度的增加而降低;随着填充墙与底层框架之间连接作用的增强,结构整体的变形减小,底层框架的损伤增大。当填充墙与底层框架之间采用弱连接时,采用强度较高的填充墙可以提高结构整体的变形能力,从而提高结构整体的抗震能力。     

考虑结构底部受剪的建筑层间位移调控及抗震性能分析

为了减少地震对建筑结构层间位移的影响,在考虑结构底部受剪的建筑中,针对层间位移调控与抗震性能的关系展开分析研究。设计建筑层间位移计算方法,计算梁、柱和节点受剪后的侧移,并依据计算结果,设置建筑层间位移限值约束条件,采用降低框架的梁距与柱距、平面结构与立体结构间的转换、弯-剪双重体系等方式,调控建筑层间位移。以某实际工程为例进行抗震性能测试验证,结果表明：所使用的层间位移计算公式的误差小于3.5%;在Kobe波与El-Centro波下的层间位移范围分别为0.43～0.82 mm和0.40～0.42 mm;经调控后,层间位移保持在0.4～1.1 mm之间,能够提升建筑的抗震性能。     

FRC框架结构的损伤程度控制及性能评估

为研究纤维增强混凝土（FRC）框架结构体系预期损伤部位的损伤程度控制和性能评估方法,采用ABAQUS有限元软件对该框架结构模型进行动力时程分析。针对该结构体系,研究其各种性能水准极限状态的定性描述和量化方法,并进行结构抗震性能评估。研究结果显示,预期损伤部位采用FRC材料,可以减小RC框架结构的层间残余侧移角、柱端截面最大转角和柱截面最大残余转角,可以控制整体结构和构件的损伤程度。给出FRC框架结构在不同性能水准下分别以柱截面转角、层间侧移角和层间残余侧移角为性能指标的限值。综合考虑FRC材料的特性和仿真结果的分析,建议选用层间残余侧移角进行性能评估更为合理。考虑8倍板厚翼缘宽度,柱梁抗弯承载力比达到1.2,FRC框架结构在8度设防烈度对应的地震作用下可达到性能等级D。     

直接基于位移设计的高强钢组合K形偏心支撑钢框架的抗震性能研究

K形高强钢组合偏心支撑(K-HSS-EBF)是指耗能连梁和支撑采用Q345钢,而框架梁、框架柱采用高强度钢(如Q460)。为研究其在罕遇地震作用下的抗震性能,在试验研究的基础上,采用直接基于位移的抗震设计方法设计了5层、8层和12层算例,分别进行静力推覆分析和动力弹塑性分析,研究高强钢组合偏心支撑钢框架在罕遇地震作用下层间侧移分布和破坏模式。研究结果表明:直接基于位移的抗震设计方法设计的算例在罕遇地震作用下,结构的层间侧移满足我国现行抗震规范的要求,结构呈理想的渐进式梁铰屈服机构,并证明该设计方法的合理性和可靠性。     

钢结构加层混凝土框架结构Pushover分析侧向力分布研究

针对钢结构加层混凝土框架结构,考虑地震作用下其层间刚度变化的影响,提出了一种计算侧向力分布的方法——层间刚度侧向力分布法。通过对一钢结构加层混凝土框架结构进行推覆分析,得到各楼层侧移、层间位移角和塑性铰分布情况,并与时程分析结果进行了比较分析。结果表明,文中方法推覆分析得到的楼层侧移和层间位移角与时程分析结果吻合较好,塑性铰分布情况也较一致,并且本方法得到的推覆曲线是推覆计算结果的下限,用于结构的抗震评估更安全。     

中高层钢筋混凝土异形柱框架-抗震墙结构的抗震性能研究

本文通过对一幢中高层住宅在不同水准地震作用下进行的弹性计算和弹塑性动力时程分析,研究了钢筋混凝土异形柱框架-剪力墙结构的动力特性和抗震能力。结果显示该结构整体抗侧刚度大,抗震性能较好。进入塑性阶段后,塑性铰分布合理,满足了结构延性设计的要求。     

应用调制原理实现建筑加层的新技术

本文以不附加原有建筑竖向和水平荷载为原则，提出了一种建筑加层新的结构设计方案。通过外包柱提供了加层附加荷载的竖向传力途径；利用隔震层、外包柱及加层结构对原结构动力响应的调制作用，保证了原结构水平地震响应不增加，因而保证在原结构不变的情况下，整体结构有足够的抗力和可靠性。本文对实际结构进行了加层设计，给出了计算分析结果。     

Active control of the seismic response of structures by combined use of base isolation and absorbing boundaries

The relative advantages of several control strategies to reduce the seismic response of multi-storey structures are studied. The strategies involve the separate or combined use of passive base isolation mechanisms and active control forces. The base isolation mechanism is modelled as an equivalent linear soft storey with high damping. The active control forces are selected so that an absorbing boundary is obtained at the top of the structure and non-reflecting or reflecting boundaries are obtained at the base of the building. It is found that the best results are obtained when a passive base isolation system is combined with an active absorbing boundary placed at the top of the building. However, the incremental gains resulting from adding a base isolation system to a structure already controlled by a roof-top active absorbing boundary are significant only for relatively soft base isolation systems. Also, the incremental gains appear to decrease as the number of storeys of the structure increases.     

日本兵库县南部地震强地震动的传播特性

依据神户海洋气象台、大阪气象台、神户港岛、神户大学、神户本山小学、尼崎及大阪福岛的强震记录，分析了强地震的走时和传播特性，指出大阪盆地的厚沉积层是造成Ｓｔ波在神户和大阪到时发生延迟的原因，由于断层在空间上的分布造成一些强震记录的波形差异。     

阻尼连体结构地震响应影响参数研究

针对阻尼连体结构,采用串并联质点系层模型,沿连体设置方向施加El Centro1940地震波,讨论了毗邻结构自振周期比与连接体阻尼刚度变化对阻尼连体结构地震响应的影响。研究结果表明:毗邻结构自振周期比与连体阻尼刚度对结构的地震响应影响较大,存在一个使结构地震响应为最优的周期比与阻尼刚度值,为实际工程应用和研究提供一些参考。     

石结构抗震可靠度的分析与应用

在文献［１］的基础上进一步探讨了石结构体系抗震动力反应分析的计算方法，给出了场地地震条件下结构在使用期间内抗震可靠度的应用实例。定量分析的结果表明，严格地控制结构高度、层数和砂浆强度等级等指标，是提高多层石结构抗震能力的有效措施。     

一类多层偏心结构的地震反应研究

本文用空间的两向抗侧力体系振动模型对五层结构分别分析了首层偏心,中间层偏心,顶层偏心和均匀偏心等不同偏心情况下的弹性地震反应规律,研究了静力偏心距,结构的基本平动周期,平扭频率比,非激励方向的平动频率等对结构的名义基底剪力和偏心层构件的最大剪力系数的影响。     

剪力墙的等效周期和等效阻尼比研究

结构弹塑性反应可用等效线性化方法中的等效刚度和等效阻尼比进行计算。为研究钢筋混凝土剪力墙的等效刚度和等效阻尼比,通过分析剪力墙的力-位移简化四折线滞回模型,推导了其屈服点和峰值点的等效刚度、等效周期和等效阻尼比的计算公式。为验证其准确性和适用性,采用提出的峰值点等效刚度、等效阻尼比公式和FEMA 440建议的公式,分别计算了42片钢筋混凝土剪力墙试件的等效刚度和等效阻尼比,并进行了对比分析。结果表明:提出的计算公式和FEMA 440建议的公式所得到的等效周期和等效阻尼比值与试验值比较吻合,因此,所提出的计算剪力墙的等效周期和等效阻尼比的公式较为合理。     

Analysis of the weightiness of site effects on reinforced concrete (RC) building seismic behaviour: The Adra town example (SE Spain)

The damage distribution in Adra town (south‐eastern Spain) during the 1993 and 1994 Adra earthquakes (5.0 magnitude), that reached a maximum intensity degree of VII (European Macroseismic Scale (EMS scale)), was concentrated mainly in the south‐east zone of the town and the most relevant damage occurred in reinforced concrete (RC) buildings with four or five storeys. In order to evaluate the influence of ground condition on RC building behaviour, geological, geomorphological and geophysical surveys were carried out, and a detailed map of ground surface structure was obtained. Short‐period microtremor observations were performed in 160 sites on a 100m × 100m dimension grid and Nakamura's method was applied in order to determine a distribution map of soil predominant periods. Shorter predominant periods (0.1–0.3 s) were found in mountainous and neighbouring zones and larger periods (greater than 0.5 s) in thicker Holocene alluvial fans. A relationship T = (0.049 ± 0.001)N, where T is the natural period of swaying motion and N is the number of storeys, has been empirically obtained by using microtremor measurements at the top of 38 RC buildings (ranging from 2 to 9 storeys). 1‐D simulation of strong motion on different soil conditions and for several typical RC buildings were computed, using the acceleration record in Adra town of the 1993 earthquake. It is noteworthy that all the aforementioned results show the influence of site effects in the degree and distribution of observed building damage. Copyright © 2007 John Wiley & Sons, Ltd.     

Identification of structural and soil properties from vibration tests of the Hualien containment model

Measurements of the response of the ¼‐scale reinforced concrete Hualien (Taiwan) containment model obtained during forced vibration tests are used to identify some of the characteristics of the superstructure and the soil. In particular, attempts are made to determine the fixed‐base modal frequencies, modal damping ratios, modal masses and participation factors associated with translation and rocking of the base. The shell superstructure appears to be softer than could have been predicted on the basis of the given geometry and of test data for the properties of concrete. Estimates of the shear‐wave velocity and damping ratio in the top layer of soil are obtained by matching the observed and theoretical system frequency and peak amplitude of the response at the top of the structure. The resulting models for the superstructure and the soil lead to theoretical results for the displacement and rotations at the base and top of the structure which closely match the observed response. Copyright © 2004 John Wiley & Sons, Ltd.     

Seismic retrofitting of braced frame buildings by RC rocking walls and viscous dampers

A design procedure for seismic retrofitting of concentrically and eccentrically braced frame buildings is proposed and validated in this paper. Rocking walls are added to the existing system to ensure an almost uniform distribution of the interstorey displacement in elevation. To achieve direct and efficient control over the seismic performance, the design procedure is founded on the displacement‐based approach and makes use of overdamped elastic response spectra. The top displacement capacity of the building is evaluated based on a rigid lateral deformed configuration of the structure and on the ductility capacity of the dissipative members of the braced frames. The equivalent viscous damping ratio of the braced structure with rocking walls is calculated based on semi‐empirical relationships specifically calibrated in this paper for concentrically and eccentrically braced frames. If the equivalent viscous damping ratio of the structure is lower than the required equivalent viscous damping ratio, viscous dampers are added and arranged between the rocking walls and adjacent reaction columns. The design internal forces of the rocking walls are evaluated considering the contributions of more than one mode of vibration. The proposed design procedure is applied to a large set of archetype braced frame buildings and its effectiveness verified by nonlinear dynamic analysis.