A Single Packer Method for Characterizing Water Contributing Fractures in Crystalline Bedrock Wells

Water levels and water quality of open borehole wells in fractured bedrock are flow-weighted averages that are a function of the hydraulic heads and transmissivities of water contributing fractures, properties that are rarely known. Without such knowledge using water levels and water quality data from fractured bedrock wells to assess groundwater flow and contaminant conditions can be highly misleading. This study demonstrates a cost-effective single packer method to determine the hydraulic heads and transmissivities of water contributing fracture zones in crystalline bedrock wells. The method entails inflating a pipe plug to isolate sections of an open borehole at different depths and monitoring changes in the water level with time. At each depth, the change in water level with time was used to determine the sum of fracture transmissivities above the packer and then to solve for individual fracture transmissivity. Steady-state wellbore heads along with the transmissivities were used to determine individual fracture heads using the weighted average head equation. The method was tested in five wells in crystalline bedrock located at the University of Connecticut in Storrs. The single packer head and transmissivity results were found to agree closely with those determined using conventional logging methods and the dissolved oxygen alteration method. The method appears to be a simple and cost-effective alternative in obtaining important information on flow conditions in fractured crystalline bedrock wells.     

Investigating changes of electrical characteristics of the saturated zone affected by hazardous organic waste

The Picillo Farm, EPA Superfund Site, in western Rhode Island was an unauthorized disposal site of hazardous organic chemicals. Predominantly organic contaminants have entered an aquifer comprised of layered glacial deposits and fractured bedrock and spread past the site boundaries with groundwater flow. Hydraulic conductivities in the glacial deposits range over two orders of magnitude and fractures and faults in the granitic bedrock further complicate the spreading of contaminants. Monitoring wells delineate two plumes that extend towards a fault-controlled valley with lakes and wetlands; one to the northwest and the other to the southwest. In this investigation we studied the electrical characteristics of both plumes.One dimensional Schlumberger depth soundings were conducted along several profile lines over the plumes and compared to those over non-contaminated sections of the site. With regard to the southwestern plume, high formation factors (ratio of bulk layer to pore water resistivity) between 12 and 45 were observed compared to values between 2.5 and 7.7 measured over the non-contaminated sections. Also, high values (> 5) of vertical electrical anisotropy (ratio of geoelectrically determined depth to high resistivity bedrock to drilled depth to bedrock) were measured over the contaminated part of the site. These values are extremely high compared to other non-contaminated sites (range: 2 to 3) in glacial stream channels of southern Rhode Island. Geoelectric measurements were affected by lateral effects. However, the consistency of high formation factors (11 to 35) and high vertical anisotropies (3 to 5) over the southwestern plume in comparison to low formation factors (3 to 8) and vertical anisotropies (1 to 1.5) over non-contaminated sites represents a marked difference between both sites. Overall, the Schlumberger depth soundings are less susceptible to near-surface lateral inhomogeneities than expected from other geoelectrical methods. Also, the disadvantage of a 1D interpretation was compensated by estimating resistivity and thickness ranges within the concept of non-uniqueness using the Dar Zarrouk parameters (Maillet, R., 1947. The fundamental equations of electrical prospecting. Geophysics, 12(4): 529–556.).The results over the northwestern plume, i.e. an area with higher contaminant concentration than the southwestern plume, were mixed and showed no consistent trends. Predominantly reducing conditions, as indicated by the presence of soluble ferric (FeII) iron hydroxides in ground water samples, increased the electrical conductivity. This is believed to have compensated the effect of high formation factors on the bulk saturated layer resistivity within the affected area.     

Study of the Santa Catarina aquifer system (Mexico Basin) using magnetotelluric soundings

A tensor magnetotelluric test survey was carried out in the region of Santa Catarina, located in the Chalco sub-basin of the Mexico Basin. The objective was to define the stratification at depth with an emphasis on the geometry of the main aquifer of that region which is partially known from DC resistivity soundings and drilling. High-quality magnetotelluric soundings could be recorded in the immediate vicinity of large urban zones because the sub-surface is very conductive. Interpretation shows that the solid bedrock is located at a depth of at least 800 m to the south and 1300 m to the north; it could, however, be much deeper. Using complementary DC resistivity sounding and well-logging data, three main layers have been defined overlying the bedrock. These layers are, from surface to bottom, an unsaturated zone of sand, volcanic ash and clay about 10 m thick, followed by a very conductive (1.5 ohm·m) 200 m thick layer of sand and ash with intercalated clay, saturated with highly mineralized water, and finally a zone with resistivity increasing gradually to 60 ohm·m. The investigated deep aquifer constitutes most of this third layer. It consists of a sequence of sand, gravel, pyroclastites and mainly fractured basalts. MT resistivity soundings and magnetic transfer functions also indicate that a shallow resistive structure is dipping, from the northwest, into the lacustrine deposits of the basin. This geologic feature is likely to be highly permeable fractured basaltic flows, which provide a channel by which water contaminated by the Santa Catarina landfill may leak into the basin.     

Hydrogeologic Framework of Fractured Sedimentary Rock,Newark Basin,New Jersey

The hydrogeologic framework of fractured sedimentary bedrock at the former Naval Air Warfare Center (NAWC), ¹ 1 For more information on the USGS Toxics Substances Hydrology Program at the Naval Air Warfare Center visit the NAWC website at http://nj.usgs.gov/nawc/
Trenton, New Jersey, a trichloroethylene (TCE)-contaminated site in the Newark Basin, is developed using an understanding of the geologic history of the strata, gamma-ray logs, and rock cores. NAWC is the newest field research site established as part of the U.S. Geological Survey Toxic Substances Hydrology Program, Department of Defense (DoD) Strategic Environmental Research and Development Program, and DoD Environmental Security Technology Certification Program to investigate contaminant remediation in fractured rock. Sedimentary bedrock at the NAWC research site comprises the Skunk Hollow, Byram, and Ewing Creek Members of the Lockatong Formation and Raven Rock Member of the Stockton Formation. Muds of the Lockatong Formation that were deposited in Van Houten cycles during the Triassic have lithified to form the bedrock that is typical of much of the Newark Basin. Four lithotypes formed from the sediments include black, carbon-rich laminated mudstone, dark-gray laminated mudstone, light-gray massive mudstone, and red massive mudstone. Diagenesis, tectonic compression, off-loading, and weathering have altered the rocks to give some strata greater hydraulic conductivity than other strata. Each stratum in the Lockatong Formation is 0.3 to 8 m thick, strikes N65°E, and dips 25° to 70°NW. The black, carbon-rich laminated mudstone tends to fracture easily, has a relatively high hydraulic conductivity and is associated with high natural gamma-ray count rates. The dark-gray laminated mudstone is less fractured and has a lower hydraulic conductivity than the black carbon-rich laminated mudstone. The light-gray and the red massive mudstones are highly indurated and tend to have the least fractures and a low hydraulic conductivity. The differences in gamma-ray count rates for different mudstones allow gamma-ray logs to be used to correlate and delineate the lithostratigraphy from multiple wells. Gamma-ray logs and rock cores were correlated to develop a 13-layer gamma-ray stratigraphy and 41-layer lithostratigraphy throughout the fractured sedimentary rock research site. Detailed hydrogeologic framework shows that black carbon-rich laminated mudstones are the most hydraulically conductive. Water-quality and aquifer-test data indicate that groundwater flow is greatest and TCE contamination is highest in the black, carbon- and clay-rich laminated mudstones. Large-scale groundwater flow at the NAWC research site can be modeled as highly anisotropic with the highest component of permeability occurring along bedding planes.     

A tracer dilution method for fracture characterization in bedrock wells

This investigation was undertaken to develop an integrated method of downhole fracture characterization using a tracer. The method presented can be used to locate water-bearing fractures that intersect the well, to determine the ambient fracture flow rate and hydraulic head, and to calculate fracture transmissivity. The method was tested in two fractured crystalline bedrock wells located at the University of Connecticut in Storrs. The method entails injecting a tracer (uranine dye) into the well, while at the same time water is pumped out of the well. After steady-state conditions are reached, a borehole tracer concentration profile is developed. The dilution of the tracer is used to locate the inflowing fractures and to determine their flow rate. The fracture flow rate, plus the drawdown in the well, is then used to determine the fracture hydraulic head, transmissivity, and ambient flow rate.     

Correlating Bedrock Folds to Higher Rates of Arsenic Detection in Groundwater,Southeast Wisconsin,USA

Arsenic in private drinking water wells is a significant problem across much of eastern Wisconsin, USA. The release mechanism and stratigraphic distribution of sulfide and iron (hydr)oxide sources of arsenic in bedrock aquifers are well understood for northeastern Wisconsin. However, recent geologic mapping has identified numerous small bedrock folds to the south, and the impact of these geologic structures on local groundwater flow and well contamination has been little studied. This paper examines the hydrologic and structural effects of the Beaver Dam anticline, southeast Wisconsin, on arsenic in groundwater in the region. Multivariate logistic regression shows wells near the Beaver Dam anticline are statistically more likely to detect arsenic in groundwater compared to wells farther away. Structural and hydrologic changes related to folding are interpreted to be the cause. Core drilled near the fold axis is heavily fractured, and many fractures are filled with sulfides. Elevated hydraulic conductivity estimates are also recorded near the fold axis, which may reflect a higher concentration of vertical fractures. These structural and hydrologic changes may have led to systematic changes in the distribution and concentration of arsenic-bearing mineral hosts, resulting in the observed detection pattern. For areas with similar underlying geology, this approach may improve prediction of arsenic risk down to the local level.     

Assessment of hydrogeological conditions in basement aquifers of the Precambrian Oban massif, southeastern Nigeria

A combined analysis of lineament length density from radar imagery and surface resistivity data is used to assess the hydrogeological conditions in the Oban massif, Nigeria. The results show that the data guided the qualitative and quantitative estimation of some aquifer parameters. These include resistivity of the water bearing formations (280–740 ω m), thickness (5–140 m), limited hydraulic conductivity (8.53-13.18 m/day) and transmissivity (410.65–725.88 m²/day) data. In addition, the lineament length density for the area ranged between less than 0.2 to slightly more than 0.4. Site evaluation for the location of productive boreholes/wells using a groundwater potential index (GWPI) indicates that areas with a GWPI of greater than 35 are consistent with relatively high yield.     

An Unsteady State Tracer Method for Characterizing Fractures in Bedrock Wells

Evaluating contaminants impacting wells in fractured crystalline rock requires knowledge of the individual fractures contributing water. This typically involves using a sequence of tools including downhole geophysics, flow meters, and straddle packers. In conjunction with each other these methods are expensive, time consuming, and can be logistically difficult to implement. This study demonstrates an unsteady state tracer method as a cost‐effective alternative for gathering fracture information in wells. The method entails introducing tracer dye throughout the well, inducing fracture flow into the well by conducting a slug test and then profiling the tracer concentration in the well to locate water contributing fractures where the dye has been diluted. By monitoring the development of the dilution zones within the wellbore with time, the transmissivity and the hydraulic head of the water contributing fractures can be determined. Ambient flow conditions and the contaminant concentration within the fractures can also be determined from the tracer dilution. This method was tested on a large physical model well and a bedrock well. The model well was used to test the theory underlying the method and to refine method logistics. The approach located the fracture and generated transmissivity values that were in excellent agreement with those calculated by slug testing. For the bedrock well tested, two major active fractures were located. Fracture location and ambient well conditions matched results from conventional methods. Estimates of transmissivity values by the tracer method were within an order of magnitude of those calculated using heat‐pulse flow meter data.     

Application of ERT,Saline Tracer and Numerical Studies to Delineate Preferential Paths in Fractured Granites

Accurate quantification of in situ heterogeneity and flow processes through fractured geologic media remains elusive for hydrogeologists due to the complexity in fracture characterization and its multiscale behavior. In this research, we demonstrated the efficacy of tracer-electrical resistivity tomography (ERT) experiments combined with numerical simulations to characterize heterogeneity and delineate preferential flow paths in a fractured granite aquifer. A series of natural gradient saline tracer experiments were conducted from a depth window of 18 to 22 m in an injection well (IW) located inside the Indian Institute of Technology Hyderabad campus. Tracer migration was monitored in a time-lapse mode using two cross-sectional surface ERT profiles placed in the direction of flow gradient. ERT data quality was improved by considering stacking, reciprocal measurements, resolution indicators, and geophysical logs. Dynamic changes in subsurface electrical properties inferred via resistivity anomalies were used to highlight preferential flow paths of the study area. Temporal changes in electrical resistivity and tracer concentration were monitored along the vertical in an observation well located at 48 m to the east of the IW. ERT-derived tracer breakthrough curves were in agreement with geochemical sample measurements. Fracture geometry and hydraulic properties derived from ERT and pumping tests were further used to evaluate two mathematical conceptualizations that are relevant to fractured aquifers. Results of numerical analysis conclude that dual continuum model that combines matrix and fracture systems through a flow exchange term has outperformed equivalent continuum model in reproducing tracer concentrations at the monitoring wells (evident by a decrease in RMSE from 199 to 65 mg/L). A sensitivity analysis on model simulations conclude that spatial variability in hydraulic conductivity, local-scale dispersion, and flow exchange at fracture-matrix interface have a profound effect on model simulations.     

Fracture Density Distributions and Well Yields in Coastal Maine

Understanding the distribution of water-bearing fractures in crystalline rock is an important component in evaluating the availability and vulnerability of water resources throughout the northeastern U.S. The State of Maine requests well drillers to report estimates of fracture depths and fracture yields for all bedrock wells drilled in the state. Using these data we analyze fracture-depth and fracture-yield data from 227 bedrock wells in coastal Maine in order to understand how fracture locations and yields are distributed with depth. Numerical simulations and statistical tests show that it is not possible to infer how fractures are distributed with depth: fracture depths are consistent with several distributions, including uniform fracture density with depth. In order to understand how fracture yield varies with depth, we group yield data into 50 foot depth intervals and compare distributions in each interval using nonparametric statistical tests. These tests show that the distribution of fracture yield in different depth intervals are statistically equivalent. These results imply that there is no empirical justification for limiting well depth when drilling for water resources in fractured bedrock in coastal Maine.     

Using direct current resistivity sounding and geostatistics to aid in hydrogeological studies in the Choshuichi alluvial fan, Taiwan

Ground water reservoirs in the Choshuichi alluvial fan, central western Taiwan, were investigated using direct-current (DC) resistivity soundings at 190 locations, combined with hydrogeological measurements from 37 wells. In addition, attempts were made to calculate aquifer transmissivity from both surface DC resistivity measurements and geostatistically derived predictions of aquifer properties. DC resistivity sounding data are highly correlated to the hydraulic parameters in the Choshuichi alluvial fan. By estimating the spatial distribution of hydraulic conductivity from the kriged well data and the cokriged thickness of the correlative aquifer from both resistivity sounding data and well information, the transmissivity of the aquifer at each location can be obtained from the product of kriged hydraulic conductivity and computed thickness of the geoelectric layer. Thus, the spatial variation of the transmissivities in the study area is obtained. Our work is more comparable to Ahmed et al. (1988) than to the work of Niwas and Singhal (1981). The first "constraint" from Niwas and Singhal's work is a result of their use of linear regression. The geostatistical approach taken here (and by Ahmed et al. [1988]) is a natural improvement on the linear regression approach.     

井旁裂缝的双侧向测井物理模拟及特征分析

为深入认识裂缝性地层的双侧向测井响应特征,指导裂缝识别及裂缝参数表征,基于数值仿真开展了井旁裂缝的缩小比例物理模拟.在物理模拟平台构建的基础上,用不同浓度的氯化钠溶液模拟基岩,用不同宽度的镀锌板来模拟高导裂缝,实现测量过程的可视化.通过实验分析井旁裂缝的规模、发育位置和产状等因素对深、浅侧向电阻率的影响.研究表明:在仪器有效探测范围内,垂直缝延伸长度对深浅侧向电阻率的数值影响较小;裂缝离井壁越远,双侧向电阻率明显增大,但深浅侧向电阻率值的降低幅度不同;随着裂缝倾角增大,深侧向电阻率增大,浅侧向电阻率无明显变化,深浅侧向电阻率从负幅度差向正幅度差过渡,但临界角的观测十分困难,应用双侧向测井判断地层产状时,需特别注意其适用条件.     

Imaging Pathways in Fractured Rock Using Three‐Dimensional Electrical Resistivity Tomography

Major challenges exist in delineating bedrock fracture zones because these cause abrupt changes in geological and hydrogeological properties over small distances. Borehole observations cannot sufficiently capture heterogeneity in these systems. Geophysical techniques offer the potential to image properties and processes in between boreholes. We used three‐dimensional cross borehole electrical resistivity tomography (ERT) in a 9 m (diameter) × 15 m well field to capture high‐resolution flow and transport processes in a fractured mudstone contaminated by chlorinated solvents, primarily trichloroethylene. Conductive (sodium bromide) and resistive (deionized water) injections were monitored in seven boreholes. Electrode arrays with isolation packers and fluid sampling ports were designed to enable acquisition of ERT measurements during pulsed tracer injections. Fracture zone locations and hydraulic pathways inferred from hydraulic head drawdown data were compared with electrical conductivity distributions from ERT measurements. Static ERT imaging has limited resolution to decipher individual fractures; however, these images showed alternating conductive and resistive zones, consistent with alternating laminated and massive mudstone units at the site. Tracer evolution and migration was clearly revealed in time‐lapse ERT images and supported by in situ borehole vertical apparent conductivity profiles collected during the pulsed tracer test. While water samples provided important local information at the extraction borehole, ERT delineated tracer migration over spatial scales capturing the primary hydrogeological heterogeneity controlling flow and transport. The fate of these tracer injections at this scale could not have been quantified using borehole logging and/or borehole sampling methods alone.     

Neogene aquifer properties specified through the interpretation of electrical sounding data,Salamiyeh region,central Syria

Twenty‐nine Schlumberger electrical soundings were carried out in the Salamiyeh region in Syria using a maximum current electrode separation of 1 km. Three soundings were made at existing boreholes for comparison. Aquifer parameters of hydraulic conductivity and transmissivity were obtained by analysing pumping test data from the existing boreholes. An empirical relationship between hydraulic conductivity determined from the pumping test and both resistivity and thickness of the Neogene aquifer has been established for these boreholes in order to calculate the geophysical hydraulic conductivity. A close agreement has been obtained between the computed hydraulic conductivity and that determined from the pumping test. The relationship established has, therefore, been generalized in the study area in order to evaluate hydraulic conductivity and transmissivity at all the points where geoelectrical measurements have been carried out. This generalization allows one to derive maps of the hydraulic conductivity and transmissivity in the study area based on geoelectrical measurements. These maps are important in future modelling processes oriented towards better exploitation of the aquifers. Copyright © 2006 John Wiley & Sons, Ltd.     

Geothermal study of reunion island: Audiomagnetotelluric survey

In 1979 and 1980, 535 magnetotelluric soundings using a frequency range of 1700 Hz-8 Hz were performed on the island of Réunion for geothermal exploration.Few direct hot-water discharges were observed. Consequently, geophysical methods, particularly the audiomagnetotelluric method, were used extensively. Favourable geological conditions for this method were encountered and the results, which were controlled using classical electrical methods on test areas, suggest an unusual distribution of resistivities for lava flows situated above suspected geothermal areas. These layers progressively decrease in resistivity down to a very conductive layer. In areas where these conductive layers were nearest the surface, detailed studies were carried out showing a close correlation between decreasing resistivity and increasing hydrothermal alteration. In addition, gradient wells reveal high geothermal gradients in such areas. The conductive layers revealed by audiomagnetotelluric soundings seem to correlate with thermal effects creating progressive hydrothermal alteration from an inferred hot-water reservoir up toward the surface.     

Utilization of Shallow Geophysical Sensing at Two Abandoned Municipal/Industrial Waste Landfills on the Missouri River Floodplain

In the past 30 to 40 years, floodplain areas of large rivers, such as the Missouri River, have been extensively used for large industrial and municipal landfills. Many of these sites are now causing varying degrees of ground water contamination. Rapid geophysical characterization techniques have proven useful for delineation of anomalous areas indicative of potential contaminant plumes. These methods have also resulted in a cost effective approach to the location and number of monitoring wells.
An effective technique to initially characterize ground water contamination at such landfills along the Missouri River in northwestern Missouri involved a combination of electrical resistivity and electromagnetic conductivity methods. Resistivity was used to obtain soundings of the alluvium by using a modified Wenner array and to corroborate shallow electromagnetic conductivity measurements by using short Wenner array electrode spacings.
Upon confirmation of similar measurements of the upper soils for the two methods, numerous electromagnetic conductivity traverses were made at each landfill site. The data generated from these surveys were graphed and contoured to delineate anomalous areas. Based on the geophysical study, a ground water monitoring well network was then designed for each landfill.
As a result, a minimal number of wells were required to initially characterize the ground water quality at these two sites. In general, analysis of water samples from these wells displayed good correlation with the geophysical results.     

Bioremediation in Fractured Rock: 1. Modeling to Inform Design,Monitoring, and Expectations

Field characterization of a trichloroethene (TCE) source area in fractured mudstones produced a detailed understanding of the geology, contaminant distribution in fractures and the rock matrix, and hydraulic and transport properties. Groundwater flow and chemical transport modeling that synthesized the field characterization information proved critical for designing bioremediation of the source area. The planned bioremediation involved injecting emulsified vegetable oil and bacteria to enhance the naturally occurring biodegradation of TCE. The flow and transport modeling showed that injection will spread amendments widely over a zone of lower‐permeability fractures, with long residence times expected because of small velocities after injection and sorption of emulsified vegetable oil onto solids. Amendments transported out of this zone will be diluted by groundwater flux from other areas, limiting bioremediation effectiveness downgradient. At nearby pumping wells, further dilution is expected to make bioremediation effects undetectable in the pumped water. The results emphasize that in fracture‐dominated flow regimes, the extent of injected amendments cannot be conceptualized using simple homogeneous models of groundwater flow commonly adopted to design injections in unconsolidated porous media (e.g., radial diverging or dipole flow regimes). Instead, it is important to synthesize site characterization information using a groundwater flow model that includes discrete features representing high‐ and low‐permeability fractures. This type of model accounts for the highly heterogeneous hydraulic conductivity and groundwater fluxes in fractured‐rock aquifers, and facilitates designing injection strategies that target specific volumes of the aquifer and maximize the distribution of amendments over these volumes.     

Site characterization in densely fractured dolomite: comparison of methods

One of the challenges in characterizing fractured-rock aquifers is determining whether the equivalent porous medium approximation is valid at the problem scale. Detailed hydrogeologic characterization completed at a small study site in a densely fractured dolomite has yielded an extensive data set that was used to evaluate the utility of the continuum and discrete-fracture approaches to aquifer characterization. There are two near-vertical sets of fractures at the site; near-horizontal bedding-plane partings constitute a third fracture set. Eighteen boreholes, including five coreholes, were drilled to a depth of approximately 10.6 m. Borehole geophysical logs revealed several laterally extensive horizontal fractures and dissolution zones. Flowmeter and short-interval packer testing identified which of these features were hydraulically important. A monitoring system, consisting of short-interval piezometers and multilevel samplers, was designed to monitor four horizontal fractures and two dissolution zones. The resulting network consisted of >70 sampling points and allowed detailed monitoring of head distributions in three dimensions. Comparison of distributions of hydraulic head and hydraulic conductivity determined by these two approaches suggests that even in a densely fractured-carbonate aquifer, a characterization approach using traditional long-interval monitoring wells is inadequate to characterize ground water movement for the purposes of regulatory monitoring or site remediation. In addition, traditional multiwell pumping tests yield an average or bulk hydraulic conductivity that is not adequate for predicting rapid ground water travel times through the fracture network, and the pumping test response does not appear to be an adequate tool for assessing whether the porous medium approximation is valid.     

裂缝性地层方位侧向测井响应数值模拟

为研究井周裂缝发育特征,本文提出一种新型方位侧向测井方法,利用三维有限元法,模拟裂缝的方位侧向测井响应.结果显示,深浅侧向电阻率幅度差异受裂缝倾角的控制,低角度缝为负差异,高角度缝为正差异;倾斜裂缝张开度的增大使测井响应值减小,方位电阻率差异增大;井周方位电阻率可反映裂缝方位产状,单一缝或裂缝密度较小时,沿裂缝走向的方位电阻率小,沿裂缝倾向的方位电阻率大;裂缝发育地层的测井响应显示宏观各向异性特征,但方位电阻率的差异显示发生反转现象,即沿裂缝走向/层理方向的方位电阻率大,沿裂缝倾向/垂直层理方向的方位电阻率小;对方位电阻率测井响应进行井周成像,直观显示了裂缝的产状和发育特征.     

Geophysical Assessment of Groundwater Potential: A Case Study from Mian Channu Area,Pakistan

An integrated study using geophysical method in combination with pumping tests and geochemical method was carried out to delineate groundwater potential zones in Mian Channu area of Pakistan. Vertical electrical soundings (VES) using Schlumberger configuration with maximum current electrode spacing (AB/2 = 200 m) were conducted at 50 stations and 10 pumping tests at borehole sites were performed in close proximity to 10 of the VES stations. The aim of this study is to establish a correlation between the hydraulic parameters obtained from geophysical method and pumping tests so that the aquifer potential can be estimated from the geoelectrical surface measurements where no pumping tests exist. The aquifer parameters, namely, transmissivity and hydraulic conductivity were estimated from Dar Zarrouyk parameters by interpreting the layer parameters such as true resistivities and thicknesses. Geoelectrical succession of five‐layer strata (i.e., topsoil, clay, clay sand, sand, and sand gravel) with sand as a dominant lithology was found in the study area. Physicochemical parameters interpreted by World Health Organization and Food and Agriculture Organization were well correlated with the aquifer parameters obtained by geoelectrical method and pumping tests. The aquifer potential zones identified by modeled resistivity, Dar Zarrouk parameters, pumped aquifer parameters, and physicochemical parameters reveal that sand and gravel sand with high values of transmissivity and hydraulic conductivity are highly promising water bearing layers in northwest of the study area. Strong correlation between estimated and pumped aquifer parameters suggest that, in case of sparse well data, geophysical technique is useful to estimate the hydraulic potential of the aquifer with varying lithology.