共查询到20条相似文献,搜索用时 15 毫秒
1.
The thruster is the crucial factor of an underwater vehicle system, because it is the lowest layer in the control loop of the system. In this paper, we propose an accurate and practical thrust modeling for underwater vehicles which considers the effects of ambient flow velocity and angle. In this model, the axial flow velocity of the thruster, which is non-measurable, is represented by ambient flow velocity and propeller shaft velocity. Hence, contrary to previous models, the proposed model is practical since it uses only measurable states. Next, the whole thrust map is divided into three states according to the state of ambient flow and propeller shaft velocity, and one of the borders of the states is defined as critical advance ratio (CAR). This classification explains the physical phenomenon of conventional experimental thrust maps. In addition, the effect of the incoming angle of ambient flow is analyzed, and Critical Incoming Angle (CIA) is also defined to describe the thrust force states. The proposed model is evaluated by comparing experimental data with numerical model simulation data, and it accurately covers overall flow conditions within ±2 N force error. The comparison results show that the new model's matching performance is significantly better than conventional models'. 相似文献
2.
《Ocean Engineering》2006,33(11-12):1413-1430
This paper presents the design of an adaptive input–output feedback linearizing dorsal fin control system for the yaw plane control of low-speed bio-robotic autonomous underwater vehicles (BAUVs). The control forces are generated by cambering two dorsal fins mounted in the vertical plane on either side of the vehicle. The BAUV model includes nonlinear hydrodynamics, and it is assumed that its hydrodynamic coefficients as well as the physical parameters are not known. For the purpose of design, a linear combination of the yaw angle tracking error and its derivative and integral is chosen as the controlled output variable. An adaptive input–output feedback linearizing control law is derived for the trajectory control of the yaw angle. Unlike indirect adaptive control, here the controller gains are directly tuned. The stability of the zero dynamics is examined. Simulation results are presented for tracking exponential and sinusoidal yaw angle trajectories and for turning maneuvers, and it is shown that the adaptive control system accomplishes precise yaw angle control of the BAUV using dorsal fins in spite of the nonlinearity and large uncertainties in the system parameters. 相似文献
3.
Predicting the velocity within the ship’s propeller jet is the initial step to investigate the scouring made by the propeller jet. Albertson et al. (1950) suggested the investigation of a submerged jet can be undertaken through observation of the plain water jet from an orifice. The plain water jet investigation of Albertson et al. (1950) was based on the axial momentum theory. This has been the basis of all subsequent work with propeller jets. In reality, the velocity characteristic of a ship’s propeller jet is more complicated than a plain water jet. Fuehrer and Römisch (1977), Blaauw and van de Kaa (1978), Berger et al. (1981), Verhey (1983) and Hamill (1987) have carried out investigations using physical model. Current paper reviews the state-of-art of the equations used to predict the time-averaged axial, tangential and radial components of velocity within the zone of flow establishment and the zone of established flow of a ship’s propeller jet. 相似文献
4.
The tracking control problem of AUV in six degrees-of-freedom (DOF) is addressed in this paper. In general, the velocities of the vehicles are very difficult to be accurately measured, which causes full state feedback scheme to be not feasible. Hence, an adaptive output feedback controller based on dynamic recurrent fuzzy neural network (DRFNN) is proposed, in which the location information is only needed for controller design. The DRFNN is used to online estimate the dynamic uncertain nonlinear mapping. Compared to the conventional neural network, DRFNN can clearly improve the tracking performance of AUV due to its less inputs and stronger memory features. The restricting condition for the estimation of the external disturbances and network's approximation errors, which is often given in the existing literatures, is broken in this paper. The stability analysis is given by Lyapunov theorem. Simulations illustrate the effectiveness of the proposed control scheme. 相似文献
5.
An adaptive output feedback controller based on neural network feedback-feedforward compensator (NNFFC) which drives a surface ship at high speed to track a desired trajectory is designed. The tracking problem of the surface ship at low speed has been widely investigated. However, the coupling interactions among the forces from each degree of freedom (DOF) have not been considered in general. Furthermore, the influence of the hydrodynamic damping is also simplified into a linear form or neglected. On the contrary, coupling interactions and the nonlinear characteristics of the hydrodynamic damping can never be neglected in high speed maneuvering situation. For these reasons, the influence of the nonlinear hydrodynamic damping on the tracking precision is considered in this paper. Since the hydrodynamic coefficients of the surface ship at high speed are very difficult to be accurately estimated as a prior, it will be compensated by NNFFC as an unknown part of the tracking dynamics system. The stability analysis will be given by the Lyapunov theory. It indicates that the proposed control scheme can guarantee that all the signals in the closed-loop system are uniformly ultimately bounded (UUB), and numerical simulations can illustrate the excellent tracking performance of the surface ship at high speed under the proposed control scheme. 相似文献
6.
Experimental Investigation of the Decay from A Ship’s Propeller 总被引:1,自引:0,他引:1
In the present study,an experimental investigation of the decay of the maximum velocity and its turbulent characteristics behind a ship propeller,in "bollard pull" condition(zero speed of advance),is reported.Velocity measurements were performed in laboratory by use of a Laser Doppler Anemometry(LDA) measurement system.Earlier researchers described that the maximum axial velocity is constant at the initial stage of a ship’s propeller jet(Fuehrer and Rmisch,1977;Blaauw and van de Kaa,1978;Berger et al.,1981;Verhey,1983) as reported in a pure water jet(Albertson et al.,1950;Lee et al.,2002;Dai,2005),but a number of researchers disagreed with the constant velocity assumption.The present study found that the maximum axial velocity decays in the zone of flow establishment and the zone of established flow with different rates.The investigation provides an insight into the decays of both the maximum velocity and the maximum turbulent fluctuation in axial,tangential and radial components and the decay of the maximum turbulent kinetic energy.Empirical equations are proposed to allow coastal engineers to estimate the jet characteristics from a ship’s propeller. 相似文献
7.
Robust control based on feedback linearization for roll stabilizing of autonomous underwater vehicle under wave disturbances 总被引:1,自引:0,他引:1
In the case of Autonomous Underwater Vehicle(AUV) navigating with low speed near water surface,a new method for design of roll motion controller is proposed in order to restrain wave disturbance effectively and improve roll stabilizing performance.Robust control is applied,which is based on uncertain nonlinear horizontal motion model of AUV and the principle of zero speed fin stabilizer.Feedback linearization approach is used to transform the complex nonlinear system into a comparatively simple linear system.For parameter uncertainty of motion model,the controller is designed with mixed-sensitivity method based on H-infinity robust control theory.Simulation results show better robustness improved by this control method for roll stabilizing of AUV navigating near water surface. 相似文献
8.
For original paper see T.I.Fossen and M.Blanke, ibid., vol.25, pp.241-55 (2000). In the work presented by Fossen and Blanke, a nonlinear observer for estimation of propeller axial flow velocity for UUVs was introduced. The proof of the convergence behavior of the observer was carried out with a Lyapunov analysis. In this technical communication, such an analysis was also briefly compared with the so-called contraction analysis. This communication goes further into the details of the comparison by proving - through a link between contracting and globally exponentially stable (GES) systems - that the observer is both contracting and GES, showing thus that contraction analysis might be regarded as an interesting alternative to Lyapunov-based designs. Furthermore, some qualitative advantages gained when using contraction analysis are given. 相似文献
9.
This paper focuses on the synchronisation between fractional-order and integer-order chaotic systems. Based on Lyapunov stability theory and numerical differentiation, a nonlinear feedback controller is obtained to achieve the synchronisation between fractional-order and integer-order chaotic systems. Numerical simulation results are presented to illustrate the effectiveness of this method. 相似文献
10.
Günter Collatz 《Ocean Engineering》1983,10(4):213-226
This article deals with model test results of a container vessel having a low block coefficient. It was fitted with an asymmetric afterbody in order to improve the water flow to the propeller and thus the propulsion. Power savings of more than 7% were attained, an interesting percentage under economic aspects. Calculations based on the wake distribution measurements showed that the variations of forces and moments at the propeller shaft were markedly below the permissible limits and that the pressure fluctuations on the shell could be reduced considerably. 相似文献
11.
螺旋桨工作时在其周围形成诱导速度场,诱导速度随到桨叶距离的增大而衰减。采用CFD方法模拟螺旋桨敞水性能时,只能截取有限尺度的流域进行计算,此时计算域边界上诱导速度并不为零,将进口速度设为进速是近似的。一般采用足够大的计算域,使螺旋桨前方及侧面边界尽量远离桨叶。为了在较小的计算域中实现螺旋桨敞水性能的准确预报,提出在设定进口速度时计入螺旋桨诱导速度的CFD模拟方法。应用升力面方法计算诱导速度,将进口速度设为进速与诱导速度之和。逐步减小计算域尺度,考察敞水性能及压力分布计算结果的变化情况及精度。算例比较表明:通过考虑诱导速度,可以大幅度减小进口与螺旋桨的距离而不降低计算精度。 相似文献
12.
13.
The paper analyses the flow around a marine propeller ducted with a so-called decelerating nozzle both through the axial momentum theory and the nonlinear semi-analytical actuator disk model. While the well-known and widely diffused axial momentum theory can be successfully employed only to qualitatively investigate the characteristics of the flow around a ducted propeller, the nonlinear and semi-analytical method can instead evaluate the thrust exerted by the duct for different values of the overall thrust and advance coefficients. There are several advantages characterising the more advanced actuator disk method. Specifically, the wake convergence and rotation may be fully taken into account, the shape of the duct and of the radial distribution of the load can be of general type, and, finally, the mutual interaction between the duct and the propeller may be readily dealt with. The methods are employed to investigate the effects of the decelerating nozzle on the efficiency and on the cavitation condition of the propeller. In particular, the influence of some duct geometrical parameters on the device performance is thoroughly analysed providing useful insights on the operating principles of this kind of propulsive systems. 相似文献
14.
Model-based feedback control of autonomous underwater gliders 总被引:6,自引:0,他引:6
We describe the development of feedback control for autonomous underwater gliders. Feedback is introduced to make the glider motion robust to disturbances and uncertainty. Our focus is on buoyancy-propelled, fixed-wing gliders with attitude controlled by means of active internal mass redistribution. We derive a nonlinear dynamic model of a nominal glider complete with hydrodynamic forces and coupling between the vehicle and the movable internal mass. We use this model to study stability and controllability of glide paths and to derive feedback control laws. For our analysis, we restrict to motion in the vertical plane and consider linear control laws. For illustration, we apply our methodology to a model of our own laboratory-scale underwater glider 相似文献
15.
Improvements of estimation accuracy on propeller torque fluctuations in waves will contribute assessments on safe operation of a ship main engine as in adverse sea condition. The propeller torque and thrust in waves can be estimated by propeller effective inflow velocity in waves, using the propeller open-water characteristics. Fluctuation components in the mathematical model of the propeller effective inflow velocity in waves can be composed of two components, respectively caused by ship surge motion and wave orbital motion at propeller position. In this study, an experimental method by the model test to directly identify the characteristics of the component by the wave orbital motion is newly proposed. Furthermore, the free-running model test in regular waves, using a simulator of the marine diesel engine which manages the shaft speed of the motor on a ship model as behaving the actual diesel engine, is carried out to obtain realistic torque fluctuations for comparisons of the estimated results applying the proposed identification method. Through comparisons of estimated fluctuations with the measured results, the proposed approach for the component of the inflow velocity due to wave orbital motion is successfully validated. 相似文献
16.
Robust Nonlinear Path-Following Control of an AUV 总被引:3,自引:0,他引:3
《Oceanic Engineering, IEEE Journal of》2008,33(2):89-102
17.
The hydrodynamic characteristics of a marine propeller operating in oblique inflow are investigated by using CFD method. Two propellers with different geometries are selected as the study subjects. RANS simulation is carried out for the propellers working at a wide range of advance coefficients and incidence angles. The effects of axial inflow and lateral inflow are demonstrated with the hydrodynamic force on the propeller under different working conditions. Based on the obtained flow field details, the hydrodynamic mechanism of propeller operating in oblique inflow is analyzed further. The trailing vortex wake of propeller is highly affected by the lateral inflow, resulting in the deflected development path and the circumferentially non-uniform structure, as well as the enhanced axial velocity in slipstream. Different flow patterns are observed on the propeller blade with the variation of circumferential position. Combined with the computed hydrodynamic forces and pressure distribution on propeller, the mechanism resulting in the increase of propulsive loads and the generation of propeller side force is explored. Finally, a systematic analysis is carried out for the propulsive loads and propeller side force as a function of axial and lateral advance coefficients. The major terms that play a dominant role in the modeling of propulsive loads and propeller side force are determined through the sensitivity analysis. This study provides a deeper insight into the hydrodynamic characteristics of propeller operating in oblique inflow, which is useful to the investigation of propeller performance during ship maneuvers. 相似文献
18.
Pan-Mook Lee Seok-Won Hong Yong-Kon Lim Chong-Moo Lee Bong-Hwan Jeon Jong-Won Park 《Oceanic Engineering, IEEE Journal of》1999,24(3):388-395
This paper presents a discrete-time quasi-sliding mode controller for an autonomous underwater vehicle (AUV) in the presence of parameter uncertainties and a long sampling interval. The AUV, named VORAM, is used as a model for the verification of the proposed control algorithm. Simulations of depth control and contouring control are performed for a numerical model of the AUV with full nonlinear equations of motion to verify the effectiveness of the proposed control schemes when the vehicle has a long sampling interval. By using the discrete-time quasi-sliding mode control law, experiments on depth control of the AUV are performed in a towing tank. The controller makes the system stable in the presence of system uncertainties and even external disturbances without any observer nor any predictor producing high rate estimates of vehicle states. As the sampling interval becomes large, the effectiveness of the proposed control law is more prominent when compared with the conventional sliding mode controller 相似文献
19.
Wei-Haur Lam Gerard Hamill Desmond Robinson Srinivasan Raghunathan 《Ocean Engineering》2010,37(14-15):1380-1388
The present paper was aimed at presenting the time-averaged velocity and turbulence intensity at the initial plane from a ship's propeller. The flow characteristics of a ship's propeller jet are of particular interest for the researchers investigating the jet induced seabed damage as documented in the previous studies. Laser Doppler Anemometry (LDA) measurements show that the axial component of velocity is the main contributor to the velocity magnitude at the initial plane of a ship's propeller jet. The tangential component contributes to the rotation while the radial component which contributes to the diffusion, are the second and third largest contributors to the velocity magnitude. The maximum tangential and radial velocity components at the initial plane are approximately 82% and 14% of the maximum axial velocity component, respectively. The axial velocity distribution at the initial plane shows two peaked ridges with a low velocity core at the rotation axis. The turbulence intensity distribution shows a three-peaked profile at the initial plane. 相似文献
20.
In this paper, the flow-induced vibrations of marine propellers in cyclic inflows are investigated both experimentally and numerically. A Laser-Doppler velocimetry (LDV) system is used to measure the axial flow velocity distributions produced by the seven-cycle wake screen in the water tunnel. A customized underwater slip ring and a single axis accelerometer sealed by silicon sealant are employed to measure the acceleration responses of rotating propeller blade. Numerical simulations of pressure fluctuations on the blades are performed using large eddy simulation (LES), while the forced vibrations of the propeller blades are obtained by a combined finite element and boundary element method. Experimental and numerical results are presented for two model propellers with the same geometries and different flexible properties, which show that the propeller blade vibrates at a frequency which is seven times as large as the axial passing frequency (APF) in the seven-cycle inflow. Moreover, the propeller blades are observed to resonance when the 7 APF excitation frequency is equal to the fundamental frequency of the propellers. The results indicate that both the inflow feature and the modal characteristic of blades contribute to flow-induced vibrations of elastic propellers. 相似文献