Fine sediment carrying capacity of combined wave and current flows

The so-called fine sediment in many coastal areas and estuaries in China is mostly referred to the mixture of cohesive sediment and non-cohesive sediment. To predict the mixed type time sediment transport, sediment carrying capacity formulae combined with the 2-D suspended sediment transport equation and morphologic equation have been widely used in China. In the present study, the sediment carrying capacity formula suggested by Dou et al. （1995） for wave conditions has been improved and implemented for the prediction of sediment transport in nearshore regions where wave activities are significant. The improvement is based on the wave energy dissipation principle inside and outside the surf zone. In the improved formula, sediment in suspension increases with the magnitude of the wave period and this feature complies with general observations. More than 300 laboratory and field measured data sets have been reviewed and 12 of them have been used to verify and determine the major coefficients in the improved formula. The application of the sediment carrying capacity model in combined wave and current situations shows that the model can faithfully reproduce the cross-shore sediment concentration distributions at the southwest coast of Bohai Bay.     

Flume‐ and field‐based evaluation of a time‐integrated suspended sediment sampler for the analysis of sediment properties

Suspended sediment has been identified as a vector for nutrient and contaminant transport in the fluvial environment. A time‐integrated sampler (the Phillips sampler), which emerged over a decade ago as a cost‐effective tool for in situ suspended sediment collection, is increasingly being used to collect samples for the analysis of sediment properties such as particle size composition, and nutrient and contaminant concentrations. This study evaluates the sampler under both flume and field conditions for efficiency in the mass and grain size of the suspended sediment collected. The sampler was tested in a flume using both kaolinite and sediment samples (sieved to < 180 µm) collected from the Quesnel River, British Columbia, Canada. In the kaolinite trails, the sampler preferentially collected coarser grain sizes compared to the original sediment, probably due to finer sediment remaining in suspension and therefore passing through the sampler, and also possibly due to flocculation of the kaolinite upon introduction to the flume. Conversely, the sampler collected river sediment that was finer than the original sediment, probably due to some settling of coarser sediment observed at the bottom of the flume. Once allowance was made for these operational issues associated with the flume, maximum sediment mass efficiency for kaolinite and river sediment was 43% and 87%, respectively. Sediment collected by the time‐integrated sampler during field deployment and adjacent channel bed sediment were also compared. The sampler collected sediment with a representative grain size distribution. However, there were differences in the geochemical (arsenic and selenium) concentrations of channel bed sediment and sediment collected by the Phillips sampler which may be a function of differences in the behavior of geochemical elements associated with the two types of sediment. This work suggests that further research is needed to evaluate the role of the Phillips sampler in collecting sediment for contaminant and nutrient analysis. Copyright © 2014 John Wiley & Sons, Ltd.     

Hillslope sediment fence catch efficiencies and particle sorting for post-fire rain storms

Sediment fences are often used to monitor hillslope erosion, but these can underestimate sediment yields due to overtopping of runoff and associated sediment. We modified four sediment fences to collect and measure the runoff and sediment that overtopped the fence in addition to the sediment deposited behind the fence. Specific objectives were to: (1) determine the catch efficiency of sediment fences measuring post-fire hillslope erosion; (2) assess particle sorting of sand, silt/clay, and organic matter from each hillslope through the sediment fence and subsequent runoff collection barrels; (3) evaluate how catch efficiency and particle size sorting relate to site and rainfall-runoff event characteristics; and (4) use runoff simulations to estimate sediment fence volumes for future post-fire monitoring. Catch efficiency ranged from 28 to 100% for events and 38 to 94% per site for the entire sampling season, indicating a relatively large underestimation of sediment yields by sediment fences. Most of the eroded sediment had similar proportions of sand and silt/clay as the hillslope soils, but the sediment behind the fence was significantly enriched in sand while the sediment that overtopped the fence was more strongly enriched in silt/clay. The sediment fences had capacities of 3 m³ for hillslopes of 0.19–0.43 ha, but simulations of runoff for 2- to 100-year storms indicate that the sediment fences would need a capacity of up to 240 m³ to store all of the runoff and associated sediment. More accurate measurements of sediment yields with sediment fences require either increasing the storage capacity of the sediment fence(s) to accommodate the expected volume of runoff and sediment, reducing the size of the contributing area, or directly measuring the runoff and sediment that overtop the fence. © 2020 John Wiley & Sons, Ltd.     

Analysis of the sediment sources of flood driven erosion and deposition in the river channel of the Fu River Basin

Studying the characteristics of runoff and sediment processes and revealing the sources of sediment provide key guidance for the scientific formulation of relevant soil erosion protection measures and water conservancy development plans. In the current study, the flow and sediment data of five hydrological stations on the main stream of the Fu River Basin (FRB) from 2007 to 2018 were selected to identify flood events, explore the variation of sediment transport along the FRB, and clarify the sediment sources. The results found that the Jiangyou–Fujiangqiao section is the main source of sediment in the FRB during the flood season. The runoff volume and sediment load during flood events in the Jiangyou–Fujiangqiao section accounted for 35% and 145% respectively of that of Xiaoheba station. These results combined with the change of the sediment load before and after the 2008 Wenchuan Earthquake (May 12) show that the sediment in this section mainly comes from the Fu River tributary–the Tongkou River watershed. The calculation results for the sediment carrying capacity of the Fu River show that the main stream was in a state of erosion in theory. However, according to the calculation results for the interval sediment yield during flood events, the sediment load at the Xiaoheba station was smaller than that at the Shehong station upstream. The analysis indicates that this was not because of sediment deposition in the river channel, but because of sand mining in the river channel and sediment interception by water conservancy projects. If heavy rainfall occurs in the FRB, the sediment accumulated upstream will move downstream with the resulting flood, and the sediment yield in the FRB may further increase. These research conclusions can provide reference information for improving the prediction and management ability of soil and water loss in the FRB and scientific regulation of the Three Gorges Reservoir.     

Sediment flux into the sea as influenced by different source areas in the drainage basin: example of the Yellow River,China

Abstract

The runoff and sediment of large rivers usually come from different source areas, which make different contributions to the sediment flux into the sea. This has been studied with the example of the Yellow River in China, whose suspended sediment flux into the Bohai Sea accounts for 19.4% of the world total. The drainage basin of this river can be divided into four major water and sediment source areas. The sediment flux into the sea is found to be closely related to the water and sediment from the different source areas in the drainage basin and, accordingly, an empirical regression model has been established to express this relationship. According to this model, in each tonne (t) of sediment from the fine sediment producing area (FSA), 0.85 t (for yearly series) and 0.72 t (for event series) can be transported into the sea; in each tonne of sediment from the coarse sediment producing area (CSA), only 0.21 t (for yearly series) and 0.34 t (for event series) can be transported into the sea. Since the 1970s, the Yellow River's sediment flux into the sea has declined markedly and this reduction can be attributed to a great degree to the soil control measures in the fine sediment producing area. Coupling the models of this study to the previously established models for estimating the impacts of soil control measures on water and sediment balance in the Yellow River basin, a quantitative prediction may be made for the change of sediment flux into the sea that might result from climate change and human activities in the future.     

Using 137Cs measurements to establish catchment sediment budgets and explore scale effects

Growing awareness of the wider environmental significance of fine sediment transport by rivers and associated sediment problems linked to sediment–water quality interactions, nutrient and contaminant transfer, and the degradation of aquatic habitats has resulted in the need for an improved understanding of the mobilization and transfer of sediment in catchments to support the development of effective sediment management strategies. The sediment budget provides a key integrating concept for assembling information on the internal functioning of a catchment in terms of its sediment dynamics by providing information on the mobilization, transfer, storage and output of sediment. One key feature of a catchment sediment budget is the relationship between the sediment yield at the catchment outlet and rates of sediment mobilization and transfer within the catchment, which is commonly represented by the sediment delivery ratio. To date, most attempts to derive estimates of this ratio have been based on a comparison of the measured sediment yield from a catchment with an estimate of the erosion occurring within the catchment, derived from an erosion prediction procedure, such as the Universal Soil Loss Equation (USLE) or its revised version, RUSLE. There is a need to obtain more direct and spatially distributed evidence of the erosion rates occurring within a catchment and to characterize the links between sediment mobilization, transfer, storage and output more explicitly. In this context, fallout radionuclides have proved particularly useful as sediment tracers. This paper reports the results of a study aimed at exploring the use of caesium‐137 (¹³⁷Cs) measurements to establish sediment budgets for three catchments of different sizes and contrasting land use located in Calabria, southern Italy. Long‐term measurements of sediment output were available for the catchments, and, by using the estimates of gross and net rates of soil loss within the catchments provided by ¹³⁷Cs measurements, it was possible to establish the key components of the sediment budget for each catchment. By documenting the sediment budgets of three catchments of different sizes, the study provides a basis for exploring the effects of scale on catchment sediment budgets and, in particular, the increasing importance of catchment storage as the size of the catchment increases. The results of this study demonstrate a reduction in the sediment delivery ratio from 98 to 2% as catchment area increases from 1·47 ha to 31·2 km². Copyright © 2010 John Wiley & Sons, Ltd.     

Equilibrium relations for water and sediment transport in the Yellow River

The equilibrium relations for water and sediment transport refer to the relative balance of sediment transport and the relative stability of river courses formed by the automatic adjustment of riverbeds.This is the theoretical basis for the comprehensive management of sediment in the Yellow River.Based on the theories of sediment carrying capacity and the delayed response of riverbed evolution,in this study,the equilibrium relations for water and sediment transport in the Yellow River are established.These relations include the equilibrium relationships between water and sediment transport and bankfull discharge in the upper and lower Yellow River and between water and sediment transport and the Tongguan elevation in the middle Yellow River.The results reveal that for the Ningmeng reach,the Tongguan reach,and the lower Yellow River,erosion and deposition in the riverbeds are adjusted automatically,and water and sediment transport can form highly constrained equilibrium relationships.These newly established equilibrium relationships can be applied to calculate the optimal spatial allocation scheme for sediment in the Yellow River.     

Laboratory investigation of the effects of mineral size and concentration on the formation of oil-mineral aggregates

Controlled laboratory studies of the formation of oil-mineral aggregates (OMA) in seawater demonstrate that sediment concentration and sediment size are key variables for determining the quantity of oil droplets stabilised by OMA formation. Experiments with a single sediment size and a range of sediment concentrations show that as sediment concentration increases, the quantity of oil trapped in OMA increases abruptly. In experiments with a single sediment concentration and a range of sediment sizes, the quantity of oil trapped in OMA decreases as sediment size increases. These results provide direct support to the hypothesis that there is a critical sediment concentration for OMA formation. Below this concentration, stabilisation of oil droplets by OMA decreases rapidly, while above this concentration, stabilisation is extensive. The results also support simple geometric models of OMA formation that predict that the critical sediment mass concentration increases linearly with sediment particle diameter. These results will help to place quantitative constraint on predictions of where and when OMA formation will be a factor in the natural dispersal of oil accidentally spilled into the ocean.     

Study of deposition of fine sediment within the pores of a coarse sediment bed stream

Elaborate experiments were performed in a 30 m long, 0.5 m deep and 0.2 m wide laboratory flume to study the process of infiltration of fine sediment into the pores of coarse sediment forming the channel bed material. Different concentrations of suspended load of fine sediment of size 0.064 mm were passed over the channel bed made up of three different types of coarse sediments; two uniform and one nonuniform. The proportion of fine sediment infiltrated into the pores of bed material for each equilibrium concentration of suspended load of fine sediment in the flow was studied during several experimental runs. The proportion of fine sediment within the pores of bed material increased with an increase in the equilibrium concentration of suspended load of fine sediment in the flow. This process continued till the pores within the coarse sediment bed were filled up to the capacity with the fine sediment transported by the flow in suspension. The theoretical value was identified for limit for maximum proportion of fine sediment that can be present within the pores of bed material. On further increase in the concentration of suspended load of fine sediment in the flow, deposition of fine sediment occurs on the surface of the flume bed in the form of ripples of the fine sediment. This condition is defined as 'depositional condition'. Experimental observations on these and related aspects are presented herein.     

Evaluation of a simple,inexpensive, in situ sampler for measuring time‐weighted average concentrations of suspended sediment in rivers and streams

The accurate measurement of suspended sediment (<200 μm) in aquatic environments is essential to understand and effectively manage changes to sediment, nutrient, and contaminant concentrations on both temporal and spatial scales. Commonly used sampling techniques for suspended sediment either lack the ability to accurately measure sediment concentration (e.g., passive sediment samplers) or are too expensive to deploy in sufficient number to provide landscape‐scale information (e.g., automated discrete samplers). Here, we evaluate a time‐integrated suspended sediment sampling technique, the pumped active suspended sediment (PASS) sampler, which collects a sample that can be used for the accurate measurement of time‐weighted average (TWA) suspended sediment concentration and sediment particle size distribution. The sampler was evaluated against an established passive time‐integrated suspended sediment sampling technique (i.e., Phillips sampler) and the standard discrete sampling method (i.e., manual discrete sampling). The PASS sampler collected a sample representative of TWA suspended sediment concentration and particle size distribution of a control sediment under laboratory conditions. Field application of the PASS sampler showed that it collected a representative TWA suspended sediment concentration and particle size distribution during high flow events in an urban stream. The particle size distribution of sediment collected by the PASS and Phillips samplers were comparable and the TWA suspended sediment concentration of the samples collected using the PASS and discrete sampling techniques agreed well, differing by only 4% and 6% for two different high flow events. We should note that the current configuration of the PASS sampler does not provide a flow‐weighted measurement and, therefore, is not suitable for the determination of sediment loads. The PASS sampler is a simple, inexpensive, and robust in situ sampling technique for the accurate measurement of TWA suspended sediment concentration and particle size distribution.     

Key drivers of changes in the sediment loads of Chinese rivers discharging to the oceans

The magnitude and variation of the sediment loads transported by rivers have important implications for the functioning of river systems and changes in the sediment loads of rivers are driven by numerous factors. In this paper, the key drivers of changes in the sediment loads of the major rivers of China are identified by reviewing recent studies of changes in their sediment loads. Except for the Songhua River, which presents no clear tendency of change in runoff or sediment load, nearly all the major rivers of China are characterized by an apparent decline in annual sediment load. The total annual sediment load of major Chinese rivers transported to the coast decreased from 2.03 billion t/yr during the period 1955–1968 to 0.50 billion t/yr during the period 1997–2010. The primary drivers of changes in the sediment loads of the rivers are dam construction, implementation of soil and water conservation measures, catchment disturbance, agricultural practices, sand mining and climate change. Examples drawn from Chinese rivers are used to demonstrate the importance of these drivers. Construction of a large number of reservoirs in the Yangtze River basin represents the primary driver for the reduced sediment load of the Yangtze River. The implementation of soil and water conservation programmes is one of the key drivers for the sharp decline in the sediment load of the Yellow River. Catchment disturbance explains why the reduction of the sediment load of the Lancang-Mekong River at the Chiang Saen gauging station was much less than that at the Gajiu gauging station upstream. A reduction in sediment load resulting from the expansion of agricultural production may be the main driver for the reduced sediment load of the Huaihe River. The decrease in the sediment load of the Pearl River has been influenced by sand mining activities. Climate change is one of the key drivers responsible for the greatly reduced sediment load of the rivers in the Haihe River Basin.     

Short‐term spatial and temporal patterns of suspended sediment transfer in proglacial channels,small River Glacier,Canada

Alpine glacial basins are a significant source and storage area for sediment exposed by glacial retreat. Recent research has indicated that short‐term storage and release of sediment in proglacial channels may control the pattern of suspended sediment transfer from these basins. Custom‐built continuously recording turbidimeters installed on a network of nine gauging sites were used to characterize spatial and temporal variability in suspended sediment transfer patterns for the entire proglacial area at Small River Glacier, British Columbia, Canada. Discharge and suspended sediment concentration were measured at 5 min intervals over the ablation season of 2000. Differences in suspended sediment transfer patterns were then extracted using multivariate statistics (principal component and cluster analysis). Results showed that each gauging station was dominated c. 80% of days by diurnal sediment transfer patterns and ‘low’ suspended sediment concentrations. ‘Irregular’ transfer patterns were generally associated with ‘high’ sediment concentrations during snowmelt and rainfall events, resulting in the transfer of up to 70% of the total seasonal suspended sediment load at some gauging stations. Suspended sediment enrichment of up to 600% from channel storage release and extrachannel inputs occurred between the glacial front and distal proglacial boundary. However, these patterns differed significantly between gauging stations as determined by the location of the gauging station within the catchment and meteorological conditions. Overall, the proglacial area was the source for up to 80% of the total suspended sediment yield transferred from the Small River Glacier basin. These results confirmed that sediment stored and released in the proglacial area, in particular from proglacial channels, was controlling suspended sediment transfer patterns. To characterize this control accurately requires multiple gauging stations with high frequency monitoring of suspended sediment concentration. Accurate characterization of this proglacial control on suspended sediment transfer may therefore aid interpretation of suspended sediment yield patterns from glacierized basins. Copyright © 2004 John Wiley & Sons, Ltd.     

Modelling sediment trapping in vegetative filter strips on steep slopes

The slope effects on sediment trapping process in vegetative filter strips (VFS) are usually neglected in current modelling practices for VFS operation, which hamper the VFS design and performance evaluation, especially on steep slopes. To fill the knowledge gap, 12 laboratory experiments of sediment trapping in VFS were conducted with three different inflow discharge (80, 100, and 120 ml s⁻¹) and four slope angles (5,10, 15, and 20°). The experimental results show that, on steep slopes (10, 15, and 20°), a part of trapped sediment particles in VFS can be eroded again and then dragged to the downstream as bed load, whilst they do not move on gentle slope (5°). To describe the complex processes, a simple and effective modelling framework was developed for sloped VFS by coupling the slope infiltration, runoff, and modified sediment transport model. The model was tested against the experimental results and good agreements between the modelled and observed results were found in both runoff and sediment transport processes for all cases. On steep slopes, the sediment trapping performance of VFS decreases significantly because the erosion of deposited sediment particles can account for more than 60% of the sediment load in the outflow. The slope effect on sediment trapping efficiency of VFS varies greatly with soil, VFS, and slope properties. The model was compared with previous sediment transport equation and found that both methods can satisfactorily predict the sediment trapping of VFS on gentle slopes, but previous sediment transport equation is likely to overestimate the sediment trapping efficiency in VFS on steep slopes. This model is expected to provide a more realistic and accurate method for predicting runoff and sediment reduction in VFS on sloping surfaces.     

Forecasting sediment distribution in reservoirs during unstable conditions

A method for rapid estimation of slopes of deposited sediment in reservoirs during unstable conditions is presented. As the limiting factor determining sediment load in a reservoir is the sediment carrying capacity of a current flowing through a reservoir, it is arqued that the slope of deposited sediment must be a function of the latter. After deriving an equation relating sediment slope to stream power, the latter being regarded as representative of sediment carrying capacity, a comparison between calculated and observed sediment slopes for average annual conditions in two South African reservoirs are presented. Using this equation as basic guideline, a semi-empirical graph is then presented which relates sediment slope to a factor representing average stream power in reservoirs.     

Calibration of an estuarine sediment transport model to sediment fluxes as an intermediate step for simulation of geomorphic evolution

Modeling geomorphic evolution in estuaries is necessary to model the fate of legacy contaminants in the bed sediment and the effect of climate change, watershed alterations, sea level rise, construction projects, and restoration efforts. Coupled hydrodynamic and sediment transport models used for this purpose typically are calibrated to water level, currents, and/or suspended-sediment concentrations. However, small errors in these tidal-timescale models can accumulate to cause major errors in geomorphic evolution, which may not be obvious. Here we present an intermediate step towards simulating decadal-timescale geomorphic change: calibration to estimated sediment fluxes (mass/time) at two cross-sections within an estuary. Accurate representation of sediment fluxes gives confidence in representation of sediment supply to and from the estuary during those periods. Several years of sediment flux data are available for the landward and seaward boundaries of Suisun Bay, California, the landward-most embayment of San Francisco Bay. Sediment flux observations suggest that episodic freshwater flows export sediment from Suisun Bay, while gravitational circulation during the dry season imports sediment from seaward sources. The Regional Oceanic Modeling System (ROMS), a three-dimensional coupled hydrodynamic/sediment transport model, was adapted for Suisun Bay, for the purposes of hindcasting 19th and 20th century bathymetric change, and simulating geomorphic response to sea level rise and climatic variability in the 21st century. The sediment transport parameters were calibrated using the sediment flux data from 1997 (a relatively wet year) and 2004 (a relatively dry year). The remaining years of data (1998, 2002, 2003) were used for validation. The model represents the inter-annual and annual sediment flux variability, while net sediment import/export is accurately modeled for three of the five years. The use of sediment flux data for calibrating an estuarine geomorphic model guarantees that modeled geomorphic evolution will not exceed the actual supply of sediment from the watershed and seaward sources during the calibration period. Decadal trends in sediment supply (and therefore fluxes) can accumulate to alter decadal geomorphic change. Therefore, simulations of future geomorphic evolution are bolstered by this intermediate calibration step.     

Muskingum equation based downstream sediment flow simulation models for a river system

Applications of sediment transport and water flow characteristics based sediment transport simulation models for a river system are presented in this study. An existing water–sediment model and a new sediment–water model are used to formulate the simulation models representing water and sediment movement in a river system. The sediment–water model parameters account for water flow characteristics embodying sediment transport properties of a section. The models are revised formulations of the multiple water inflows model describing water movement through a river system as given by the Muskingum principle. The models are applied to a river system in Mississippi River basin to estimate downstream sediment concentration, sediment discharge, and water discharge. River system and the river section parameters are estimated using a revised and the original multiple water inflows models by applying the genetic algorithm. The models estimate downstream sediment transport rates on the basis of upstream sediment/water flow rates to a system. Model performance is evaluated by using standard statistical criteria;downstream water discharge resulting from the original multiple water inflows model using the estimated river system parameters indicate that the revised models satisfactorily describe water movement through a river system. Results obtained in the study demonstrate the applicability of the sediment transport and water flow characteristics-based simulation models in predicting downstream sediment transport and water flow rates in a river system.     

Sediment routing analyses based on chronological changes in hillslope and riverbed morphologies

Recent studies of sediment delivery and budgets in the United States indicate that upland erosion rates at a given time may not explain contemporaneous sediment yields from a drainage basin. This suggests temporal discontinuities in sediment delivery associated with hillslope and channel storage processes. Integration of sediment production, storage and transport is essential to understand sediment routing in basins. We analysed each process chronologically using aerial photographs, monitoring data of sediment movement and annual tree-rings, and then compared estimated temporal changes in sediment production from hillslopes, floodplain disturbance areas and sediment transport in river channels. Toeslopes, floodplains and alluvial fans together contained 59 per cent of sediment eroded from uplands over the last 30 years. Monitoring results of riverbed changes showed that the volume of stored sediment on floodplains decreased exponentially with succeeding floods. The age distribution of floodplain deposits reflected the disturbance history of a river channel, and followed an exponential decrease with age. The results of this study may have important implications for sediment control plans for watersheds in steep regions.     

Identifying subsoil sediment sources with carbon and nitrogen stable isotope ratios

Increased sediment loads from accelerated catchment erosion significantly degrade waterways worldwide. In the South East Queensland region of Australia, sediment loads are degrading Moreton Bay, a Ramsar listed wetland of international significance. In this region, like most parts of coastal Australia, sediment is predominantly derived from gully and channel bank erosion processes. A novel approach is presented that uses carbon and nitrogen stable isotope ratios and elemental composition to discriminate between these often indistinguishable subsoil sediment sources. The conservativeness of these sediment properties is first tested by examining the effect of particle size separation (testing for consistency during transport) and the effect of sampling at different times (testing for temporal source consistency). The discrimination potential of these sediment properties is then assessed with the conservative properties, based on the particle size and temporal analyses, modelled to determine sediment provenance in three catchments. Nitrogen sediment properties were found to have significant particle size enrichment and high temporal variance indicative of non‐conservative behaviour. Conversely, carbon stable isotopes had very limited particle size and temporal variability highlighting their suitability for sediment tracing. Channel erosion was modelled to be a significant source of sediment (μ 51%, σ 9%) contrasting desktop modelling research that estimated gully erosion is the predominant sediment source. To limit the supply of sediment to Moreton Bay, channel bank and gully erosion must both be targeted by sediment management programs. By distinguishing between subsoil sediment sources, this approach has the potential to enhance the management of sediment loads degrading waterways worldwide. Copyright © 2014 John Wiley & Sons, Ltd.     

TEMPORAL AND SPATIAL DYNAMICS OF DIFFERENT PARTICLE SIZE OF SUSPENDED SEDIMENT IN THE LIU RIVER CATCHMENTS,CHINA

1 INTRODUCTION The particle size of sediment eroded from basins can provide basic information about erosion processes (Meyer et al., 1980), which can be divided into sheet wash sediment processes on hill slopes and fluvial sediment processes in rivers. In…     

Determining suspended sediment loads from turbidity records / La détermination des charges en suspension des rapports sur la turbidité

Abstract

The Pennsylvania Department of Transportation and the US Geological Survey are cooperating in several field studies to evaluate sediment control measures used during highway construction. Among the parameters being monitored are suspended sediment concentration and turbidity. Sediment loads are calculated from suspended sediment and water discharge data, but some sediment loads must be determined indirectly because it is virtually impossible to obtain sufficient suspended sediment samples to define all runoff conditions adequately. Sediment discharge-water discharge correlation curves have proved unreliable for streams affected by highway construction, so an alternative method using the turbidity record was developed during these studies.

The field data reveal a good correlation between daily mean discharge-weighted turbidity and daily mean discharge-weighted suspended sediment concentration. Turbidity is monitored and recorded continuously, and the daily mean discharge-weighted turbidity is calculated from the turbidity and water discharge data. During periods when there are insufficient suspended sediment data, the daily mean discharge-weighted suspended sediment concentration is determined from the turbidity-sediment correlation and used with the daily mean water discharge to calculate a daily sediment load.

This method of determining sediment loads from the turbidity record suggests a possiblity for computation of sediment loads by computer. Instrumentation now in use for recording water quality parameters on digital punch tape could be used to record the output from a turbidimeter. Then, for streams having a good correlation between suspended sediment concentration and turbidity, simultaneous water discharge and turbidity data could be used to determine sediment loads by computer.