小角度成层倾斜场地动力响应分析的大型振动台试验研究

基于大型振动台试验,研究小角度成层倾斜场地在倾向、走向、垂向、坡面方向、坡面垂直方向上的地震动响应特征,以及地层倾角对场地反应谱的影响规律。试验结果表明：在倾向方向,随着地层倾角的增大,倾斜场地的放大效应增大;在走向方向,当地层倾角小于12.5°时,放大效应强于水平成层场地;在倾向、走向方向,当地层倾角达到12.5°时,场地对反应谱短周期T≤0.1 s部分具有放大作用,对T＞0.1 s的部分具有削弱作用;在垂向方向,随着地层倾角的增加,倾斜场地的放大效应强于水平成层场地;在坡面方向,倾斜场地的放大效应弱于水平成层场地;在坡面垂向方向,倾斜场地的放大效应强于水平成层场地。该研究成果对小角度成层倾斜场地上的建筑物抗震设计具有一定的参考意义。     

华北板块南缘的变形分解:洛南-栾川断裂带与秦岭北缘强变形带研究

秦岭洛南-栾川断裂带具有左旋斜向俯冲的运动学特征,其产状一般为107°/N∠65°。华南板块的俯冲方向为80°,俯冲角度为42°;华南板块运动方向为42°,运动方向与华北板块南部边界的夹角为65°,汇聚角25°。秦岭北缘强变形带内褶皱枢纽延伸方向为290°,与洛南-栾川断裂带存在15°的夹角。逆冲断层走向与褶皱的枢纽方向基本一致,大多数断层与洛南-栾川断裂带有相同的运动学极性,性质为左行平移逆断层。平移正断层走向主要为NE SW,断层性质、展布方向、运动学特征与板块汇聚的应力作用方式吻合;片理、片麻理走向117°,与洛南-栾川断裂带走向夹角为10°。在垂直剪切带的剖面上,系统观察岩石变形特征,测量面理产状,进行岩石有限应变测量,岩石非共轴递进变形分析结果表明:秦岭北缘强变形带内由南向北面理走向与剪切带走向的夹角逐渐增大,岩石剪应变量依次递减,造山带变形具有“三斜对称”特点。     

三层倾斜层的电测深曲线正演计算与解析

本文是探讨三层倾斜层的直流电测深问题。文中通过三层倾斜层的数学模型,就各种参数(第一、二倾斜层的倾角及各倾斜层的电阻率值变化,测线平行、正交、斜交于倾斜层走向)进行了大量的电测深正演计算,并对正演计算结果加以探讨。计算结果表明,其值与三层水平层测深结果有较大的差别,如曲线的尾支渐近值差异,垂直倾斜层走向布极的测深曲线产生畸变,以及在某些地电参数下,测深曲线无法正确地反映地下的地电断面等。因此,在野外实际工作中,对于利用三层水平层的理论计算结果来解释三层倾斜层时,必须注意其解释误差。     

The structure and timing of lateral escape during the Scandian Orogeny: A combined strain and geochronological investigation in Finnmark, Arctic Norwegian Caledonides

Determining the timing, duration and mechanism of tectonic events within an orogenic cycle, such as ocean subduction, continent–continent collision or gravitational collapse, is challenging, especially in ancient orogenic belts. Variations in the tectonic transport direction, however, can be used as a guide to these stages of orogeny. While thrust sheets within the Caledonian allochthon in north Norway were emplaced broadly eastwards perpendicular to the trend of the orogen, many features indicate material transport in other orientations. One dominant feature of the Magerøy Nappe, sitting above and infolded with the Kalak Nappe Complex, is the development of a strong N–S lineation orthogonal to the main transport direction. Strain measurements, in part determined by a new method, are used, in the context of the regional structural data to identify the critical stage in orogeny when compressional forces are balanced by orogen-parallel lateral escape. Quantitative 3-D strain estimation in the Magerøy Nappe indicates prolate deformation with c. 50% horizontal shortening parallel to the thrusting direction (E–W) and c. 200% extension along the orogenic strike (N–S) with c. 30% vertical shortening. Temporal constraint on this fabric is provided by Ar–Ar isotopic analysis of undeformed white mica in cross-cutting granitic pegmatites. These data show that prolate deformation occurred before the white mica cooling age of 416 ± 4 Ma, while the previously determined depositional age of the Hellefjord Schist indicates that it occurred after 438 ± 4 Ma. A granitic pegmatite that intruded the Hellefjord Schist after an initial deformation phase but during or prior to a later deformation, has been dated at 431 ± 2 Ma by U–Pb zircon. A previous lower age constraint on this deformation of 428 ± 5 Ma is given by metamorphic zircon overgrowths on fractured grains. These results constrain the continental collision between Baltica and Laurentia in Finnmark to the interval c. 431–428 Ma. Placed in a regional context, these results indicate that lateral escape was orthogonal to the thrusting direction and occurred during the continent–continent collision stage in the Scandian Orogeny before gravitationally driven collapse.     

斜向逆冲断层相关褶皱的正演模型与实例分析

斜向逆冲作用在自然界普遍存在,研究斜向逆冲断层相关褶皱的构造几何学特征,识别断层相关褶皱是否存在斜向逆冲有重要意义。文章采用Trishear 4.5、Gocad以及Trishear3D软件构建一系列不同滑移量的断层转折褶皱和断层传播褶皱的二维正演剖面,通过连接一系列不同排列方式的二维剖面建立了三种不同逆冲滑移方向的断层转折褶皱和断层传播褶皱的假三维模型,通过不同假三维模型的比较分析来探讨斜向逆冲断层相关褶皱的构造几何学特征。研究发现,斜向逆冲断层相关褶皱区别于正向逆冲断层相关褶皱的特征主要有两点：① 正向逆冲断层相关褶皱层面等高线图上的最高点与后翼等高线中点的连线以及水平切面上的核心点与后翼中点的连线方向均与断层走向垂直,而斜向逆冲断层相关褶皱的最高点以及核心点与后翼中点的连线方向均与断层走向斜交,并且最高点与后翼等高线中点的连线方向或者核心点与后翼中点的连线方向均与逆冲滑移方向一致;② 在褶皱平行断层走向纵剖面上,正向逆冲断层相关褶皱各个层面最高点的连线是直立的,而斜向逆冲断层相关褶皱各个层面最高点的连线发生倾斜。通过这两个特征可以判别褶皱是否存在斜向逆冲以及逆冲的方向。将模型分析结果运用到四川盆地西南部三维地震勘探资料所覆盖的邛西背斜和大兴西背斜的实例中。研究结果表明,两个背斜均存在右旋斜向逆冲,逆冲方向与各自断层走向的夹角均为70°左右,邛西背斜和大兴西背斜的逆冲方向分别是NE79°和NE77°左右,这与龙门山南段晚上新世以来的主应力方向以及反演的汶川地震最大主应力方向一致。     

造山带挤出构造与高压-超高压岩石剥露机制:以大别山为例

造山带挤出构造阐述了被边界断裂所围限的造山带深变质块体,在造山带内部垂向和(或)侧向应力的作用下折返变形的过程。研究主要集中在挤出块体的几何形态及其内部变形样式、边界断裂特征、挤出路径以及挤出动力来源等4个方面,其研究目的主要是为了解决造山带深变质岩石折返剥露的机制问题。依据挤出块体的挤出方向与造山带主体走向之间的关系,在三维球形坐标系Lx-Ly-Lz中,将造山带挤出构造大致分为7个端员类型(Ⅰ型～Ⅶ型)。其中Lx为造山带或俯冲带的主体走向;Ly呈水平方向并与Lx相垂直;Lz垂直于Lx和Ly所构成的平面。这些基本端员类型的组合及其之间的过渡类型可以详尽地诠释大别山印支期高压-超高压岩石的挤出过程。其中榴辉岩相挤出阶段介于Ⅳ型与Ⅶ型挤出构造之间,角闪岩相挤出阶段介于Ⅱ型与Ⅵ型挤出构造之间并可能具有渠道流挤出模式,而绿片岩相挤出阶段类似于Ⅴ型挤出构造。     

Pseudo 3-D modeling of trishear fault-propagation folding

Basement structures, to which trishear fault-propagation models have most successfully been applied, are commonly three-dimensional folds formed at the tip-line of a fault. We present here a ‘pseudo-3D’ trishear model in which various parameters are permitted to vary along strike and oblique-slip can be modeled. These variations may be combined in an infinite number of ways, facilitating the simulation of many real structures. A thrust changing from blind to emergent can be produced by a change in the slip or propagation-to-slip (P/S) along strike. Folds with forelimbs changing from overturned to upright along strike can be modeled either by changing the slip, P/S or trishear angle. Also some minor folds perpendicular or oblique to the main structure can result from changes in the trishear angle or fault angle along the strike. Models including growth strata show that it is practically impossible to distinguish between growth and pre-growth strata using the map patterns. As a field test, we have modeled the oblique slip East Kaibab monocline, demonstrating a good fit between the field observations and model predictions.     

Indentation of a continent with a built-in thickness change: experiment and nature

Orogens oblique to the direction of plate convergence are currently attributed to obliquity between the margins of one or both of the sutured continents to their direction convergence. We use a single analogue experiment and natural examples to illustrate a potential additional factor: variations in strength of the indented continent at a high angle to the convergence direction. The wavelengths of structures in laterally shortened lithosphere depend on the strength of the most competent layers. Lateral variations in crustal thickness must therefore lead to structures oblique to any applied lateral compression.

An analogue experiment was performed to explore this phenomenon. A two-layer ‘indented continent’ was modelled by a brittle upper crust of sand above a lower crust of high-viscosity polymer floating on a single layer of low-viscosity syrup representing the mantle. The well-known strike-slip structures allowing lateral escape to distant weak boundaries were hindered by lateral boundaries in front of the indenter. This allowed us to focus on the effects of a thickness change built into the ‘indented continent’ along a zone parallel to the direction in which a vertical rigid wall advancing at a steady rate represented the indenter. Vertical escape led to an ‘orogenic belt’ oblique to the advancing wall; this obliquity influences subsequent lateral escape. Model scaling and interpretations are based on Extended Thin Sheet Approximation (ETSA) and standard theories of faulting.

Four sectors of the Alpine–Himalayan orogen (Iran, Tunisia, the Eastern Alps and the Himalaya) are oblique to the continental convergence direction, and we point to thickness changes at high angles to the suture that may account for this geometry. As crustal thicknesses north of oblique sectors of the Himalayas are not yet known, we speculate on them.

We infer from the main difference between our experiment and all our examples chosen from nature that vertical orogenic escape was oblique to our model suture but can be parallel to natural sutures.     

Characteristics of vertical land movement and microearthquake activity in the northeastern Japan arc

Methods have been devised for analyzing vertical land movement and seismicity data using two-dimensional Chebychev functions and oblique projections. A filtering operation in the space domain is made possible by use of a two-dimensional Chebychev function. The oblique projections give an intuitive understanding of land deformation. Characteristic aspects of vertical land movement obtained by precise levelling and of the energy release of microearthquakes with depths shallower than 20 km in the northeastern Japan arc were investigated in detail applying these methods.Lineations with wavelength of about 20–60km trending towards NE—SW were found for both the land deformation and the seismicity. It should be noted that this trend is almost perpendicular to the direction of the strain migration and is related to other geophysical information.     

Cleavage strain in the Variscan fold belt,County Cork,Ireland, estimated from stretched arsenopyrite rosettes

In south-west Ireland, hydrothermally formed arsenopyrite crystals in a Devonian mudstone have responded to Variscan deformation by brittle extension fracture and fragment separation. The interfragment gaps and terminal extension zones of each crystal are infilled with fibrous quartz. Stretches within the cleavage plane have been calculated by the various methods available, most of which can be modified to incorporate terminal extension zones. The Strain Reversal Method is the most accurate currently available but still gives a minimum estimate of the overall strain. The more direct Hossain method, which gives only slightly lower estimates with this data, is more practical for field use. A strain ellipse can be estimated from each crystal rosette composed of three laths (assuming the original interlimb angles were all 60°) and, because actual rather than relative stretches are estimated, this provides a lower bound to the area increase in the plane of cleavage. Based on the average of our calculated strain ellipses this area increase is at least 114% and implies an average shortening across the cleavage of at least 53%. However, several lines of evidence suggest that the cleavage deformation was more intense and more oblate than that calculated, and we argue that a 300% area increase in the cleavage plane and 75% shortening across the cleavage are more realistic estimates of the true strain. Furthermore, the along-strike elongation indicated is at least 80%, which may be regionally significant. Estimates of orogenic contraction derived from balanced section construction should therefore take into account the possibility of a substantial strike elongation, and tectonic models that can accommodate such elongations need to be developed.     

Quantitative finite strain and kinematic flow analyses along the Zagros transpression zone, Iran

The Ghouri area in southwest Iran exposes a cross section through the Zagros orogenic belt. The area provides an opportunity to investigate quantitative finite strain (Rs), kinematic vorticity number (W_k), proportions of pure shear and simple shear components, sense of shear indicators, steeply plunging lineations, and other moderate to steeply plunging stretching lineations in a transpressional zone. Based on a classical strain analysis of deformed microfossils with oblate strain ellipsoid shape, the Zagros orogenic belt is classified as a pure-shear dominated zone of transpression, but asymmetry of shear-sense indicators suggests that a significant component of simple shear was involved along the deformation zone boundaries. The long axes of the microfossils and stretched pebbles of a deformed conglomerate were used to indicate the stretching direction in this zone. The stretching lineations have a steep to moderate plunge but a constant strain magnitude. Characteristics of dextral inclined transpressional kinematics in the Zagros continental collision zone were quantified and indicate an estimated k-value < 1, an angle between the maximum horizontal axis of the instantaneous strain ellipsoid and the zone boundary (θ = 32°), asymmetrical dextral shear-sense indicators, and an angle of relative plate motion (α = 25°).     

大兴断层的三维几何学与运动学及其对廊固凹陷成因机制的约束

大兴断层是位于渤海湾盆地冀中坳陷西北部的廊固凹陷的边界大断层,控制着整个凹陷的沉积和构造演化。根据大兴断层的走向特征,将研究区内的大兴断层分为东北段、中段、西南段3段,并对其结合处成因进行了探讨。文中首次将大兴断层断面以三维立体形态展示出来,并对大兴断面的三维几何形态进行了详细的剖析。认为大兴断面是个由多个倾斜面组成的曲面,每个相邻的倾斜面通过轴面而分隔。轴面通过其走向特征,分为横向轴面与垂向轴面,其中横向轴面为平行断层走向的轴面,而垂向轴面则是垂直断层走向的轴面。通过4个横向轴面与2个垂直轴面将大兴断面分为10个区,每个区都有各自的形态与特征。对大兴断层的活动机制进行了探讨,认为大兴断层初期是以多米诺式运动模式为主,后期在翘倾作用下发生旋转,从而形成上陡下缓的犁式断层。其上盘地层的运动模式则是初期与断层同时发生旋转,地层陡且直,在上陡下缓的断面形成后,以斜剪切模式运动,形成滚动背斜。     

Quartz <Emphasis Type="Italic">c</Emphasis>-axis texture mapping of mylonitic metapelite with rod structures (Calabria,southern Italy): Clues for hidden shear flow direction

This quantitative microstructural study deals with textures of quartz domains within a mylonitized metapelite collected near a thrust surface corresponding to the tectonic contact between two metamorphic units, which crop out in the Aspromonte Massif, southern Calabria (Italy). The sample investigated lacks a mesoscopic stretching lineation. Therefore, quartz c-axis fabrics were investigated in two mutually orthogonal thin sections (a) parallel to the quartz rod lineation and perpendicular to the foliation (YZ plane) and (b) perpendicular to the quartz rods and perpendicular to the foliation (XZ plane); the data were generated using classical (manual measurements of quartz c-axis using U-stage) and modern methods (Computer Integrated Polarization microscopy). Both these sections show oblique foliations at ca. 40° from the main shear plane, implying that the actual X direction (stretching lineation that is absent on the mesoscopic scale) must lie between these two sections. Quartz c-axis data from the YZ section when rotated by 90° are similar with those from the XZ section. Hence, the data from the two sections are merged. These data when rotated by an angle of 50° from the direction of quartz rod lineation, gives an asymmetrical pattern indicating top-to-the-North sense of shear. This was confirmed by investigating quartz c-axis patterns in a section striking NS and perpendicular to the foliation. Based on the study it is thus concluded that this method can be used to do kinematic analysis in rocks that are devoid of stretching lineations. Apart from the above, the advantages and disadvantages of the classical and modern methods of quartz c-axis analysis are discussed.     

中国东南大陆岩石圈演化研究中的有关问题雏议

本文依据大地构造理论和最新研究资料对中国东南大陆岩石圈演化研究中的有关问题作了探讨，认为地体理论和大地构造相模式理论是相辅相成的；建议扬弃华夏古陆、特提斯构造域和太平洋构造域等可能束缚研究思路的概念；将板片构造、斜向碰撞与走滑纳入中国东南部碰撞造山带的研究内容     

一个韧性转换挤压带的变形分解作用：以阿尔金断裂带东段为例

变形构造研究显示阿尔金划分成具有近水平拉伸线理的韧性左行走滑变形域和具有陡角度倾伏拉伸线理的收缩变形域。在ＳＳ与ＰＳ之间的过渡区域还发现中等角度倾伏的拉伸线理。     

2008年汶川大地震小鱼洞地表破裂带精细填图

5·12汶川Mw7.9级地震为罕见的、地壳尺度位移配分于多条平行断裂的板内逆冲走滑型地震。在2条北东走向、近平行的主要地表破裂间,发育北西走向的小鱼洞地表破裂。介绍了对小鱼洞北西向地表破裂的精细填图。小鱼洞地表破裂空间上位于灌县-江油与映秀-北川断裂间,全长约8km,总体走向310°,为南西盘抬升、逆冲兼具左旋走滑性质。地表破裂在南东端走向变化较大,从300~310°变为南北向,并与灌县-江油地表破裂带的磁峰段相连。小鱼洞地表破裂的垂向位错自北西往南东方向递减,北西端陡坎高度最大3.4m,南东端则小于0.2m,衰减梯度约为0.5m/km。左旋走滑位移测量点较少,集中在中段的小鱼洞镇附近,所测最大左旋走滑位移约为2.2m,一般走滑位错与同处垂直位错具有同步变化的特征。小鱼洞断裂近地表的倾角较缓,为30°±15°。结合已有地貌、地球物理和地质研究结果,提出小鱼洞断裂是向下与灌县-江油断裂交会的侧向断坡,位于映秀-北川断裂中南段间的断面倾角差异的撕裂部位,连接映秀-北川和灌县-江油断裂。在运动学上,认为小鱼洞断裂是以斜向断坡为几何形态的撕裂断裂,调节了北东走向的主断裂的运动学横向差异。小鱼洞断裂上的同震位移矢量与N70°、80°E的区域主压应力场方向匹配。这一方向与龙门山高原边界斜交。     

地层倾角对转换波动校速度分析的影响

动校正速度的求取是三维转换波数据处理的重要环节,其精度高低对转换波的叠加成像质量影响很大。理论上转换波的速度求取受包括界面倾角在内的多种因素影响,但实际应用时这些因素往往被忽略。为证明倾角对动校速度的影响程度,依据前人的研究成果,模拟倾斜地层计算了不同倾角条件下二维测线CCP道集、三维全方位CCP道集PS波动校正速度,并对由不同倾角引起的计算精度差异进行了研究。研究结果表明,对于二维转换波CCP道集,界面倾角不同,动校拉平的速度会差别较大,即使如此也总能实现很大倾角范围内的CCP道集的同相叠加,获得较好的成像质量;对于三维全方位CCP道集,当界面倾角超过一定范围,无论怎样进行精细扫描,得到的都只能是适合特定方位的速度,无法得到适合任意方位的动校扫描速度,随着界面倾角的减小,利用速度扫描的办法可以在一定的偏移距范围内将来自不同方位的记录较平,界面倾角越小,可以校平的偏移距越大;另外由于道集内的地震记录依赖视倾角的动校正速度,在反射界面倾斜的情况下,方位不同,动校正速度不同,致使二维反射PS波资料往往比三维反射PS波资料容易叠加成像。     

Deformation produced by oblique rifting

With oblique rifting, both extension perpendicular to the rift trend and shear parallel to the rift trend contribute to rift formation. The relative amounts of extension and shear depend on α, the acute angle between the rift trend and the relative displacement direction between opposite sides of the rift. Analytical and experimental (clay) models of combined extension and left-lateral shear suggest the fault patterns produced by oblique rifting. If α is less than 30°, conjugate sets of steeply dipping strike-slip faults form in rifts. Sinistral and dextral strike-slip faults trend subparallel and at large angles to the rift trend, respectively. If α is about 30°, strike-slip, oblique-slip and/or normal faults form in rifts. Faults with sinistral and dextral strike slip trend subparallel and at large angles to the rift trend, respectively. Normal faults strike about 30° counterclockwise from the rift trend. If α exceeds 30°, normal faults form in rifts. They have moderate dips and generally strike obliquely to the rift trend and to the relative displacement direction between opposite sides of the rift. If α equals 90°, the normal faults strike parallel to the rift trend and perpendicularly to the displacement direction.The modeling results apply to the Gulf of California and Gulf of Aden, two Tertiary continental rift systems produced by combined extension and shear. Our results explain the presence and trends of oblique-slip and strike-slip faults along the margins of the Gulf of California and the oblique trend (relative to the rift trend) of many normal faults along the margins of both the Gulf of California and the Gulf of Aden.     

基底收缩对挤压构造变形特征影响——来自砂箱实验的启示

进行了 4个砂箱模型的模拟实验。其中基底收缩单侧挤压剖面模型以形成后冲叠瓦式断层为特征 ,基底无收缩单侧挤压剖面模型则以发育前冲叠瓦断层为特征。基底收缩斜向双侧挤压平面模型形成两组不同走向的逆断层 ,一组为与挤压带边界基本平行的主控断层 ,另一组为与挤压方向近于垂直的雁列断层。而基底无收缩斜向双侧挤压平面模型仅形成一组与挤压带边界基本平行的逆断层。这些模型的实验结果表明 ,基底收缩对挤压构造变形特征具有重要的影响。后冲 (或向陆冲向 )叠瓦式这种较为罕见挤压构造、以及与挤压方向近垂直的雁列断层的形成与基底的收缩作用有关。对于类似于焉耆盆地这种通常认为是压剪形成的挤压构造组合 ,笔者认为用“基底收缩条件下的斜向挤压作用”可更加贴切地加以解释。     

Development of quartz c-axis crossed/single girdles under simple-pure shear deformation: Results of visco-plastic self-consistent modeling

Quartz c-axis fabrics are widely used to determine the shear plane in ductile shear zones, based upon an assumption that the shear plane is perpendicular to both the central segment of quartz c-axis crossed girdle and single girdle. In this paper the development of quartz c-axis fabric under simple-pure shear deformation is simulated using the visco-plastic self-consistent (VPSC) model so as to re-examine this assumption. In the case of no or weak dynamic recrystallization, the simulated crossed girdles have a central segment perpendicular or nearly perpendicular to the maximum principal finite strain direction (X) and the XY finite strain plane, and at a variable angle relative to the imposed kinematic framework that is dependent on the modeled flow vorticity and finite strain. These crossed girdles have a symmetrical skeleton with respect to the finite strain axes, regardless of the bulk strain and the kinematic vorticity, and rotate in a way similar to the shear sense with increasing bulk strain ratio. The larger the vorticity number the more asymmetrical their legs tend to be. In the case of strong dynamic recrystallization and large bulk strain, under simple shear the crossed girdle switches into single girdles, sub-perpendicular to the shear plane, by losing the weak legs. The numerical results in our models do not confirm the above-mentioned assumption.