Jurassic plutonism and crustal evolution in the central Mojave Desert,California

Middle to Late Jurassic plutonic rocks in the central Mojave Desert represent the continuation of the Sierran arc south of the Garlock fault. Rock types range from calc-alkaline gabbro to quartz monzonite. Chemical and isotopic data indicate that petrologic diversity is attributable to mixing of crustal components with mantle melts. Evidence for magma mixing is scarce in most plutons, but emplacement and injection of plutons into preexisting wallrocks (e.g. pendants of metasedimentary rocks) suggests that assimilation may be locally important. Field and petrographic evidence and major and trace element data indicate that the gabbros do not represent pure liquids but are, at least partly, cumulates. The cumulate nature of the gabbros coupled with field evidence for open-system contamination means that trace element contents of gabbros cannot be used to fingerprint the Jurassic mantle source, nor can isotopic data be unequivocally interpreted to reflect the isotopic composition of the mantle. Correlation of Sr and Nd isotropic composition with bulk composition allows some constraints to be placed on the mantle isotopic signature. Gabbros and mafic inclusions from localities north of Barstow, CA have the most depleted mantle-like isotopic signatures (Sr _{( i )}≈0.705 and ɛNd _(t)=≈0 to +1). However, these rocks have likely seen some contamination as well, so the mantle source probably has an even more depleted character. Gabbros with the lowest Sr( _i ) and highest ɛNd _(t) are also characterized by the highest ²⁰⁷Pb/²⁰⁴Pb and ²⁰⁶Pb/²⁰⁴Pb in the entire data set. This may be a feature of the mantle component in the Jurassic arc indicative of minor source contamination with subducted sediment as has been observed in modern continental arcs. Locally exposed Precambrian basement and metasedimentary rocks have appropriate Sr, Nd and Pb isotopic signatures for the crustal end members and are possible contaminants. Incorporation of these components through combined anatexis and assimilation can explain the observed spread in isotopic composition. Evidence for a depleted mantle component in these gabbros contrasts with the enriched subcontinental mantle component in Jurassic arc plutons further to the east and suggests there may have been a major mantle lithosphere boundary between the two areas as far back as the Late Jurassic. Crustal boundaries and isotopic provinces defined on the basis of initial isotopic composition (Sr( _i )=0.706 isopleth) are difficult to delineate because of the correlation of bulk composition with Sr and Nd isotopic composition and because values may differ depending on the age of the rocks sampled within a given area. Data from plutons intruded into rocks known or inferred to be Precambrian are, however, shifted dramatically (highest Sr_{( i )} and lowest ɛNd_(t)) toward Precambrian values. The least isotopically evolved rocks (lowest Sr( _i ) and highest ɛNd_(t)) occur within the eugeoclinal belt of the Mojave Desert. This zone has been previously identified as a Precambrian rift zone but more likely represents a zone where mantle magmas have been intruded into isotopically similar crustal rocks of the eugeocline with minor input from old Precambrian crust. Received: 12 August 1993/Accepted: 8 July 1994     

The practicalities of using CFCs and SF6 for groundwater dating and tracing

Knowledge of groundwater residence time is important in understanding key issues in the evolution of water quality, whether this occurs due to water–rock interaction or simply by mixing or contamination. The build-up in the atmosphere of the trace gases chlorofluorocarbons (CFCs) and sulphur hexafluoride (SF₆) from the middle of the last century offers a convenient way of dating waters up to ∼60 a old. The gases are well-mixed in the atmosphere so their input functions are not area-specific as is the case with ³H. While any one of these trace gases can in principle provide a groundwater age, when two or more are measured on water samples the potential exists to distinguish between different modes of flow including piston flow, exponential flow and simple end-member mixing. As with all groundwater dating methods, caveats apply. Factors such as recharge temperature and elevation must be reasonably well-constrained. Primarily for SF₆, the phenomenon of ‘excess air’ also requires consideration. Primarily for the CFCs, local sources of contamination need to be considered, as do redox conditions. For both SF₆ and the CFCs, the nature and thickness of the unsaturated zone need to be factored into residence time calculations. However, as an inexpensive dating method, the trace gases can be applied to a wide range of groundwater problems where traditional age indicators might once have been used more sparingly. Examples include tracing flowlines, detecting small modern inputs in ‘old’ waters, and pollution risk assessment. In the future, with the main CFCs already declining in the atmosphere, new anthropogenic trace gases are likely to take their place.     

Helium accumulation in groundwater. II: A model for the accumulation of the crustal 4He degassing flux

A model of ⁴He accumulation in a confined aquifer is presented which includes in situ production and a crustal degassing flux of ⁴He into the bottom of a confined aquifer. The model is consistent with the measurements of ⁴He concentration in the Great Artesian Basin, Australia (Torgersen and Clarke, 1985) and also with the measurements of ⁴He concentration in the Auob Sandstone of Namibia (Heaton, 1981). The measured value of the crustal degassing flux of ⁴He from these two areas is comparable with the ⁴He degassing flux calculated from the atmospheric budget of ⁴He (Wasserburget al., 1963; Ozima and Podosek, 1983). A literature review suggests that a crustal degassing ⁴He source may account for the ⁴He accumulation in many other groundwater systems. It is concluded from the literature review, the detailed modelling of ⁴He accumulation in GAB and the Auob Sandstone, and the atmospheric budget that crustal degassing of ⁴He may be a common and widespread phenomena.     

K-H3OFe3(SO4)2(OH)6铁矾的XRD研究

根据X射线衍射(XRD)分析发现: A Fe₃(SO₄)₂(OH)₆(A=K⁺、H₃O⁺)系列铁钒的XRD数据十分相近,难以用XRD区别,需通过能谱(EDS)辅助分析,才能区分此类铁矾。另外,此类铁矾的003和107面网间距d随K⁺含量增大而增大,且呈一元三次方程的关系;而033和220面网间距d随K⁺含量增大而减小,呈一元二次方程的关系。对该现象从铁矾晶体结构方面进行解释:K⁺、H₃O⁺离子位于较大空隙中,且沿着Z轴方向排列,当K⁺、H₃O⁺离子之间相互替换时,会导致该铁矾晶体结构在Z轴方向有较明显的变化。     

Experimental evidence for carbonate precipitation and CO2 degassing during sea ice formation

Chemical and stable carbon isotopic modifications during the freezing of artificial seawater were measured in four 4 m³ tank incubations. Three of the four incubations were inoculated with a nonaxenic Antarctic diatom culture. The 18 days of freezing resulted in 25 to 27 cm thick ice sheets overlying the residual seawater. The ice phase was characterized by a decrease in temperature from −1.9 to −2.2°C in the under-ice seawater down to −6.7°C in the upper 4 cm of the ice sheet, with a concurrent increase in the salinity of the under-ice seawater and brine inclusions of the ice sheet as a result of physical concentration of major dissolved salts by expulsion from the solid ice matrix. Measurements of pH, total dissolved inorganic carbon (C_T) and its stable isotopic composition (δ¹³C_T) all exhibited changes, which suggest minimal effect by biological activity during the experiment. A systematic drop in pH and salinity-normalized C_T by up to 0.37 pH_SWS units and 376 μmol C kg⁻¹ respectively at the lowest temperature and highest salinity part of the ice sheet were coupled with an equally systematic ¹³C enrichment of the C_T. Calculations based on the direct pH and C_T measurements indicated a steady increase in the in situ concentration of dissolved carbon dioxide (CO₂(aq)) with time and increasing salinity within the ice sheet, partly due to changes in the dissociation constants of carbonic acid in the low temperature-high salinity range within sea ice. The combined effects of temperature and salinity on the solubility of CO₂ over the range of conditions encountered during this study was a slight net decrease in the equilibrium CO₂(aq) concentration as a result of the salting-out overriding the increase in solubility with decreasing temperature. Hence, the increase in the in situ CO₂(aq) concentration lead to saturation or supersaturation of the brine inclusions in the ice sheet with respect to atmospheric pCO₂ (≈3.5 × 10⁻⁴ atm). When all physico-chemical processes are considered, we expect CO₂ degassing and carbonate mineral precipitation from the brine inclusions of the ice sheet, which were saturated or highly supersaturated with respect to both the anhydrous (calcite, aragonite, vaterite) and hydrated (ikaite) carbonate minerals.     

The bearing of the system CaMgSi2O6CaAl2SiO6CaFeAlSiO6 on fassaitic pyroxene

The system CaMgSi₂O₆CaAl₂SiO₆CaFeAlSiO₆ has been studied in air at 1 atm. The phase assemblage at subsolidus temperatures in the CaMgSi₂O₆-rich portion is Cpx + An + Mel and that in the CaMgSi₂O₆-poor portion Cpx + An + Mel + Sp. At subsolidus temperatures the sigle-phase field of clinopyroxene increases with an increase in the CaFeAlSiO₆ component of the system. The Al₂O₃ content of clinopyroxene, however, continues to increase beyond the single-phase field and attains at least 16.04 wt.% Al₂O₃ with 3.9 wt.% Fe₂O₃. The stability field of fassaite in the system over a range of pressures and oxygen fugacities has been estimated from data in the literature as well as the present data. The CaFeAlSiO₆ content of fassaite is dependent on oxygen fugacity, but is not influenced by pressure. The stability field is strongly influenced by oxygen fugacity at low and high pressure, and decreases with decreasing oxygen fugacity. Clinopyroxenes in both volcanic and metamorphic rocks from various localities, when plotted on the CaMgSi₂O₆CaAl₂SiO₆CaFeAlSiO₆ triangle, show that there is no compositional gap between diopside and fassaitic pyroxene in metamorphic rocks, and that the fassaitic pyroxene in alkalic rocks becomes richer in both CaAl₂SiO₆ and CaFeAlSiO₅ components as crystallization proceeds. These results agree with those obtained in the experimental study.     

Actinide crystal-liquid partitioning for clinopyroxene and Ca3(PO4)2

Using fission and alpha track radiography techniques, we have measured partition coefficients (D) for the actinide elements Th, U and Pu between diopsidic clinopyroxene, whitlockite [β-Ca₃ (PO₄)₂] and silicate liquid at 20kbar. Equilibrium partitioning at the crystal-liquid interface is assumed, and corrections for actinide zoning have been applied to the measured D values. Reproducibility for both actinide and minor element D values is carefully examined as a criterion for crystal-liquid interface equilibrium. The data are mostly compatible with interface equilibrium except for experiments at high cooling rates ( ? 30 deg/hr). Partition coefficients for Th/U/Pu of about 0.002/0.002/0.06 are measured for clinopyroxene and 1.2/0.5/3.4 for whitlockite. At an oxygen fugacity of 10^?8.5, Pu is much more readily incorporated into the crystalline phases than is U or Th because of the importance of trivalent Pu. The D_Pu(cpx) is similar to D(cpx) of the light rare earths supporting the concept of Pu/(rare earth) dating.     

Free energy of formation for green rust sodium sulphate (NaFe6Fe3(OH)18(SO4)2(s))

In a recent study, sulphate-bearing green rust (GR_SO4) was shown to incorporate Na⁺ in its structure (NaFe^II₆Fe^III₃(OH)₁₈(SO₄)_2(s); GR_Na,SO4). The compound was synthesised by aerial oxidation of Fe(OH)_2(s) in the presence of NaOH. This paper reports on its free energy of formation .Freshly synthesised GR_Na,SO4 was titrated with 0.5 M H₂SO₄ in an inert atmosphere at 25 °C, producing dissolved Fe²⁺ and magnetite or goethite. Solution concentrations, PHREEQC and the MINTEQ database were used to calculate reaction constants for the reactions:

     

Evolution of the chemistry of Fe bearing waters during CO2 degassing

The rates of Fe(II) oxidation and precipitation from groundwater are highly pH dependent. Elevated levels of dissolved CO₂ can depress pH and cause difficulty in removing dissolved Fe and associated metals during treatment of ferruginous water. This paper demonstrates interdependent changes in pH, dissolved inorganic C species, and Fe(II) oxidation rates that occur as a result of the removal (degassing) of CO₂ during aeration of waters discharged from abandoned coal mines. The results of field monitoring of aeration cascades at a treatment facility as well as batchwise aeration experiments conducted using net alkaline and net acidic waters in the UK are combined with geochemical modelling to demonstrate the spatial and temporal evolution of the discharge water chemistry. The aeration cascades removed approximately 67% of the dissolved CO₂ initially present but varying the design did not affect the concentration of Fe(II) leaving the treatment ponds. Continued removal of the residual CO₂ by mechanical aeration increased pH by as much as 2 units and resulted in large increases in the rates of Fe(II) oxidation and precipitation. Effective exsolution of CO₂ led to a reduction in the required lime dose for removal of remaining Fe(II), a very important factor with regard to increasing the sustainability of treatment practices. An important ancillary finding for passive treatment is that varying the design of the cascades had little impact on the rate of CO₂ removal at the flow rates measured.     

Thermochemistry of glasses along joins of pyroxene stoichiometry in the system Ca2Si2O6-Mg2Si2O6-Al4O6

Enthalpies of solution in 2PbO · B₂O₃ at 974 K have been measured for glasses along the joins Ca₂Si₂O₆ (Wo)-Mg₂Si₂O₆ (En) and Mg₂Si₂O₆-MgAl₂SiO₆ (MgTs). Heats of mixing are symmetric and negative for Wo-En with W_H = ?31.0 ± 3.6 kJ mol^?. Negative heats of mixing were also found for the En-MgTs glasses (W_H = ?33.4 ± 3.7 kJ mol^?).Enthalpies of vitrification of pyroxenes and pyroxenoids generally increase with decreasing alumina content and with decreasing basicity of the divalent cation.Heats of mixing along several glassy joins show systematic trends. When only non-tetrahedral cations mix (outside the aluminosilicate framework), small exothermic heats of mixing are seen. When both nontetrahedral and framework cations mix (on separate sublattices, presumably), the enthalpies of mixing are substantially more negative. Maximum enthalpy stabilization near compositions with Al/Si ≈ 1 is suggested.     

Calorimetric measurements of fusion enthalpies for Ni2SiO4 and Co2SiO4 olivines and application to olivine-liquid partitioning

Calorimetric measurements of fusion enthalpies for Ni₂SiO₄ and Co₂SiO₄ olivines were carried out using a high-temperature calorimeter, and Ni and Co partitioning between olivine and silicate liquid was analyzed using the measured heats of fusion. The fusion enthalpy of Co₂SiO₄ olivine measured by transposed-temperature drop calorimetry was 103 ± 15 kJ/mol at melting point (1688 K). The fusion enthalpy of Ni₂SiO₄ olivine was calculated based on the enthalpies of liquids in the system An₅₀Di₅₀-Ni₂SiO₄ measured by transposed-temperature drop calorimetry at 1773 K, and was 221 ± 26 kJ/mol at its metastable melting point (1923 K). The fusion enthalpy of Ni₂SiO₄ is the largest among those of olivine group, this is caused by the large crystal field stabilization energy of six-coordinated Ni²⁺ in olivine. The larger fusion enthalpy of Ni₂SiO₄ can account for the large and variable partition coefficient of Ni between olivine and silicate liquid. Based on the comparison between partition coefficients calculated from thermodynamic data and those observed in partition experiments, it is considered that the magnitude of partition coefficients is primarily dependent on the heats of fusion of the components. Furthermore, the activity coefficients for Ni-, Co- and Mn-bearing components in magmatic liquid are nearly of the same magnitude.     

Solubility of Fe-ettringite (Ca6[Fe(OH)6]2(SO4)3 · 26H2O)

The solubility of Fe-ettringite (Ca₆[Fe(OH)₆]₂(SO₄)₃ · 26H₂O) was measured in a series of precipitation and dissolution experiments at 20 °C and at pH-values between 11.0 and 14.0 using synthesised material. A time-series study showed that equilibrium was reached within 180 days of ageing. After equilibrating, the solid phases were analysed by XRD and TGA while the aqueous solutions were analysed by ICP-OES (calcium, sulphur) and ICP-MS (iron). Fe-ettringite was found to be stable up to pH 13.0. At higher pH-values Fe-monosulphate (Ca₄[Fe(OH)₆]₂(SO₄) · 6H₂O) and Fe-monocarbonate (Ca₄[Fe(OH)₆]₂(CO₃) · 6H₂O) are formed. The solubilities of these hydrates at 25 °C are:      

Acid dissociation mechanisms of Si(OH)4 and Al(H2O)6 in aqueous solution

Silicic acid and the hexa-aqua of Al³⁺ are fundamental model aqueous species of chemical importance in nature. In order to investigate their hydroxyl dissociation mechanisms, Car-Parrinello molecular dynamics (CPMD) simulations were carried out, which allow treating the solutes and solvents on the same footing. The method of constraint was employed to trigger the reactions by taking coordination number as the reaction coordinate and the thermodynamic integration was used to obtain the free-energy profiles. The approximate transition states were located and the reactant and product states were also characterized. The free-energy changes of dissociation are found about 15.0 kcal/mol and 7.7 kcal/mol for silicic acid and Al-aqua, respectively. From the simulation results, the first pKas were calculated by using two approaches, which are based on the pristine thermodynamic relation and the RDF (radial distribution function)-free energy relation, respectively. Because of more uncertainties involved in the RDF way, it is suggested that the pristine way should be favored, which shows an error margin of 1 pKa unit. This study provides an encouraging basis for applying the present methodology to predict acidity constants of those groups that are difficult to measure experimentally.     

CO2 degassing and trapping during hydrothermal cycles related to Gondwana rifting in eastern Australia

Intensive carbonate and clay mineral authigenesis took place throughout the Late Permian Bowen-Gunnedah-Sydney basin system in eastern Australia. We conducted isotopic and trace element analyses of carbonate and clay minerals from clastic sedimentary rocks of the Gunnedah Basin and the Denison Trough in the Bowen Basin. Rb-Sr isochron age data of the illitic clays are consistent with episodic hydrothermal fluid flow events that occurred in association with Gondwana rifting accompanied by alkaline magmatism at ∼85 Ma and ∼95 Ma. Stable isotope data of carbonate and clay minerals from the Gunnedah Basin are indicative of meteoric waters from a high-latitude environment as the main fluid source, whereas trace element, Sr and Nd isotope data highlight mixing of meteoric fluids with magmatic and/or crustal components, with a possible input from marine carbonates for some samples. Trace metals, oxygen and strontium isotopes of dawsonites from the Denison Trough are interpreted to have been mobilised by fluids that interacted with evolved clastic sedimentary and marine carbonate end members. According to the carbon isotope data, CO₂ for calcite and ankerite precipitation was sourced mainly from thermal degradation of organic matter and magmatism, whereas the CO₂ used for dawsonite formation is inferred to have been derived from magmatic and marine sources. In the low permeability environments (particularly in coal seams), the increasing accumulation and oversaturation of CO₂ particularly promote the precipitation of dawsonite.     

Solubility of pyromorphite Pb5(PO4)3Cl-mimetite Pb5(AsO4)3Cl solid solution series

Pyromorphite Pb₅(PO₄)₃Cl and mimetite Pb₅(AsO₄)₃Cl are isostructural minerals with apatite. Due to their high environmental stability, they have gained considerable attention as metals sequestration agents in water treatment and contaminated soil remediation. Pyromorphite and mimetite can form a continuous solid solution series in near-Earth surface environments. Precipitation of the end members and intermediate members of the series is likely to occur in the areas where the cost-effective in situ immobilization reclamation method, based on phosphate amendments, is applied. In contrast to the widely studied thermodynamic parameters of pyromorphite and mimetite, knowledge of the thermodynamics of their solid solutions is sparse. To supplement the data, a number of compounds from the pyromorphite-mimetite series were synthesized at room temperature using a method to simulate the conditions in the near-Earth surface environments. Afterwards, batch dissolution and dissolution-recrystallization experiments of seven synthesized precipitates were conducted at 25 °C, pH = 2 and in a 0.05 M KNO₃ background electrolyte. The experiments were carried out for a period of 6 (dissolution) and 14 (dissolution-recrystallization) months. A plateau in the [Pb] evolution patterns was used to determine equilibrium. All seven dissolutions were congruent, and the ionic activity products (IAP) of the minerals from the pyromorphite-mimetite solid solution series were calculated based on the dissolution reaction: . The IAPs for pyromorphite and mimetite exhibit a significant difference in values over three orders of magnitude between approximately 10⁻⁷⁹ for pyromorphite and approximately 10⁻⁷⁶ for mimetite. The series appeared to be ideal, and Lippmann and Roozboom diagrams were used for better understanding of its thermodynamics. The results indicated a strong tendency of pyromorphite to partition into the solid phase in the series, which explains some of the naturally observed phenomena. The improvement of the lattice stability of the mimetite due to isostructural phosphate substitutions in anionic sites was observed. The thermodynamic data reported in this study supplement existing databases used in geochemical modeling.     

N2-CH4（CO2）混合气体在线标样制备及其拉曼定量因子测定

利用混合气体的标准样品对激光拉曼探针进行标定,可以快速准确地对包裹体中的无机及有机气相组分进行定量分析。而常用的商用钢瓶装混合气体标样,存在费用高、气体组成单一固定等缺点。本文设计了一套在线标样制备装置,提出一种在线配置不同浓度和压力条件下混合气体标样的方法。利用高纯度(纯度99.999%)的N2、CH4以及CO2钢瓶气,经过在线混合增压,在5 MPa和10 MPa条件下制备了N2摩尔分数为30%、50%和70%的N2-CH4以及N2-CO2混合气体在线标样。该方法制备的标样与70%N2+30%CO2的商用钢瓶气标样对比表明,CO2与N2的拉曼相对峰高以及相对峰面积值的误差在4%以内,具有较高的准确度和重现性。通过不同压力和浓度条件下CH4以及CO2的拉曼相对定量因子测定表明,气体的相对定量因子在5~10 MPa压力条件下与压力及组成无关。地质样品应用结果表明,本方法可以方便、灵活、准确地按任意比例将两瓶及两瓶以上纯气体钢瓶样品进行混合及增压,为激光拉曼标定、气体组成原位测量等提供了一种新的技术思路。     

Phosphoinnelite, Ba4Na3Ti3Si4O14(PO4,SO4)2(O,F)3, a new mineral species from peralkaline pegmatite of the Kovdor pluton, Kola Peninsula

Phosphoinnelite, an analogue of innelite with P > S, has been found in a peralkaline pegmatite vein crosscutting calcite carbonatite at the phlogopite deposit, Kovdor pluton, Kola Peninsula. Cancrinite (partly replaced with thomsonite-Ca), orthoclase, aegirine-augite, pectolite, magnesioarfvedsonite, golyshevite, and fluorapatite are associated minerals. Phosphoinnelite occurs as lath-shaped crystals up to 0.2 × 1 × 6 mm in size, which are combined typically in bunch-, sheaf-, and rosettelike segregations. The color is yellow-brown, with vitreous luster on crystal faces and greasy luster on broken surfaces. The mineral is transparent. The streak is pale yellowish. Phosphoinnelite is brittle, with perfect cleavage parallel to the {010} and good cleavage parallel to the {100}; the fracture is stepped. The Mohs hardness is 4.5 to 5. Density is 3.82 g/cm³ (meas.) and 3.92 g/cm³ (calc.). Phosphoinnelite is biaxial (+), α = 1.730, β = 1.745, and γ = 1.764, 2V (meas.) is close to 90°. Optical orientation is Z^c ∼ 5°. Chemical composition determined by electron microprobe is as follows (wt %): 6.06 Na₂O, 0.04 K₂O, 0.15 CaO, 0.99 SrO, 41.60 BaO, 0.64 MgO, 1.07 MnO, 1.55 Fe₂O₃, 0.27 Al₂O₃, 17.83 SiO₂, 16.88 TiO₂, 0.74 Nb₂O₅, 5.93 P₂O₅, 5.29 SO₃, 0.14 F, −O=F₂ = −0.06, total is 99.12. The empirical formula calculated on the basis of (Si,Al)₄O₁₄ is (Ba_3.59Sr_0.13K_0.01)_Σ3.73(Na_2.59Mg_0.21Ca_0.04)_Σ3.04(Ti_2.80Fe _0.26 ³⁺ Nb_0.07)_Σ3.13[(Si_3.93Al_0.07)_Σ4O₁₄(P_1.11S_0.87)_Σ1.98O_7.96](O_2.975F_0.10)_Σ3.075. The simplified formula is Ba₄Na₃Ti₃Si₄O₁₄(PO₄,SO₄)₂(O,F)₃. The mineral is triclinic, space group P or P1. The unit cell dimensions are a = 5.38, b = 7.10, c = 14.76 ?; α = 99.00°, β = 94.94°, γ = 90.14°; and V = 555 ?³, Z = 1. The strongest lines of the X-ray powder pattern [d, ? in (I)(hkl)] are: 14.5(100)(001), 3.455(40)(103), 3.382(35)(0 2), 2.921(35)(005), 2.810(40)(1 4), 2.683(90)(200, 01), 2.133(80)( 2), 2.059(40)(204, 1 3, 221), 1.772(30)(0 1, 1 7, 2 2, 2 3). The infrared spectrum is demonstrated. An admixture of P substituting S has been detected in the innelite samples from the Inagli pluton (South Yakutia, Russia). An innelite-phosphoinnelite series with a variable S/P ratio has been discovered. The type material of phosphoinnelite has been deposited at the Fersman Mineralogical Museum, Russian Academy of Sciences, Moscow. Original Russian Text ? I.V. Pekov, N.V. Chukanov, I.M. Kulikova, D.I. Belakovsky, 2006, published in Zapiski Rossiiskogo Mineralogicheskogo Obshchestva, 2006, No. 3, pp. 52–60. Considered and recommended by the Commission on New Minerals and Mineral Names, Russian Mineralogical Society, May 9, 2005. Approved by the Commission on New Minerals and Mineral Names, International Mineralogical Association, July 4, 2005 (proposal 2005-022).