半潜式钻井平台复合锚泊系统组分配比优化设计

从提高锚泊系统收放时效性入手,提出了一种半潜式钻井平台复合式锚泊系统组分配比优化设计方法,旨在尽可能降低复合式锚泊系统的钢链配比长度,提高收放效率。结合锚泊系统设计参数,制定优化设计准则,建立优化分析流程,采用ANSYS-AQWA建立锚泊定位半潜式平台水动力分析模型,获得平台运动参数和锚链动力参数,对平台漂移量、锚链最小安全系数、走锚临界张力、锚链最小卧底长度和起锚力进行无量纲指标分析,并综合考虑张力倾角与预张力对优化结果的影响,获得复合式锚泊系统钢链与钢缆的最优配比关系,确定最优钢链长度为395 m,较原钢链长度缩短225 m,钢链收放时间降低36%,进一步提高锚泊系统收放时效性,并降低平台可变荷载。     

半潜式支持平台系泊系统的设计方法及应用

系泊系统是半潜式支持平台抵抗恶劣海洋环境作用、限制平台偏移、实现海上定位的重要设备,辐射状多点系泊是常用的布置方式。针对该平台系泊系统开展了设计方法和分析流程研究,阐述了系泊系统配置设计,包括系泊缆的数量、抛出长度、单根系泊缆的刚度、直径、破断负荷、定位锚的型式、最大抓力等;系泊系统的布置设计,包括系泊缆之间的水平夹角、系泊绞车、导缆器、定位锚的位置等;同时归纳风载荷、流载荷以及波浪慢漂载荷的常用估算方法;总结适用于该类平台系泊系统设计的规范要求。将上述方法和流程应用于某型半潜式支持平台系泊系统的开发和设计,采用系泊定位分析程序MIMOSA对该系统的定位能力进行分析,研究了系泊缆形状、夹角等参数随张力的变化特征,同时系泊缆按照船级社的规范要求进行衡准,反复调整和优化系泊系统的配置和布置方式,直至系泊系统满足要求,最终设计出较合适的系泊系统。相关方法、流程和结论为实际工程项目提供重要的设计思路。     

Dynamic Analysis of Semi-Submersible Production Platform Under the Failure of Mooring Lines

This paper quantitatively studies the transient dynamic response of a semi-submersible production platform with the loss of one or several positioning mooring lines.A semi-submersible platform,production risers,and positioning mooring lines are all included in the numerical simulation.Increased motion of the semi-submersible platform,tension variation of the remaining mooring lines/risers and the risk of mooring line or riser clashing are all investigated through fully coupled time-domain analysis.Combined environmental loads are selected from irregular waves and the steady current varying from very rough to extreme sea conditions.Three dimension radiation/diffraction theories and Morison’s equation are applied to calculate first-order wave force and second-order mean drift force of floating semi-submersible platform.Nonlinear time-domain finite element methods are employed to analyze the behavior of mooring lines and risers.Results show that the failure of mooring lines seriously reduce the platform’s stability performance.The tension of the rest lines is also increased accordingly.Remaining lines which are closer to the failed lines will have larger tension increase to compensate.Line-Line distance provides practical information for the risk of clashing investigation.     

深水圆筒型钻井平台张紧式系泊系统设计

基于我国南海海域环境条件,对一座深水圆筒型钻井平台设计一套张紧式系泊定位系统,利用SESAM软件对平台运动响应和缆索张力进行分析计算,得到主要运动响应为纵荡、纵摇和垂荡。分别考虑0°和180°的环境载荷方向,对比得到0°方向的缆索张力更大,且6号和7号缆承受了主要的环境力。分析了平台运动的影响因素,认为缆索夹角设定为35°时较优,适度增大系泊缆初始长度和减小两端锚链长度可较为有效地降低系泊缆受力,系泊缆总根数保持12时（4根×3组）为最优方案。根据分析结果对初始系泊方案进行了优化,在风暴工况下系泊缆最大受力减小了约14.8%。钻井作业工况和一根系泊缆破断工况下,系泊缆受力和平台位移均能满足规范要求。     

锚泊辅助动力定位系统单缆失效影响研究

针对半潜式钻井平台锚泊辅助动力定位系统在海上作业时可能会出现的单缆失效情况。以一艘半潜式平台为例,设计锚泊辅助动力定位系统。通过全动态时域模拟,研究不同的单缆失效模式对半潜式平台锚泊辅助动力定位系统功率消耗、定位精度、缆绳张力等的影响。根据分析结果,在极端海况下,松弛锚泊辅助动力定位系统的背风缆有助于降低定位系统的功率消耗,提高定位精度和系统的安全性,从而为锚泊辅助动力定位系统的工程应用提供一些参考。     

Study on a new mooring system integrating catenary with taut mooring

Analyzed are the merits and demerits of catenary mooring system and taut mooring system, which are commonly used nowadays. As falling somewhere between these two systems, a new mooring system integrating catenary with taut mooring is proposed. In order to expound and prove the advantages of this new system, the motion performance of a semi-submersible platform is simulated by employing full time domain coupled analysis method. A comparison of the result of new mooring system with that of taut mooring system shows that the movement of the platform using the new type mooring system is smaller than that using the taut mooring system, which ensures a better working condition. Furthermore, the new mooring system is also compatible with the characteristics of catenary mooring system, which eliminates the requirement of anti-uplift capacity of the anchors.     

深水半潜式平台系泊系统动力特性研究

探讨张紧式系泊系统的基本特征,比较张紧式和悬链线式系泊半潜平台运动和动力响应特性,分析拖曳力系数变化对张紧式和悬链线式系泊动力效应的影响,以及张紧式和悬链线式系泊缆节点运动特点,从而为改善半潜平台系泊系统动力效应提供参考.     

内孤立波中半潜平台动力响应特性

基于内孤立波mKdV理论,采用时域有限位移运动方程,结合改进的Morison公式,研究了两层流体中内孤立波与带分段式悬链系泊约束半潜平台的相互作用问题。针对东沙群岛南部海域附近某实测内孤立波特征参数,计算分析了在该内孤立波作用下SEDCO-700型半潜平台的内孤立波载荷、运动响应及其系泊张力的变化特性。研究表明,内孤立波不仅会对半潜平台产生突发性冲击载荷作用,使其产生大幅度水平漂移运动,并导致其系泊张力显著增大,因此在半潜平台等深海平台的设计与应用中,内孤立波的影响是不可忽视的。     

内孤立波下深水半潜式平台系统动力响应研究

我国南海海域海洋环境条件复杂且海水密度垂直层化现象显著,内孤立波活动频繁,因内孤立波而造成海洋开采平台破坏的案例屡见不鲜。依托水动力计算软件AQWA二次开发功能,采用Kdv方程,借助Fortran语言将深水半潜式平台立柱、浮箱、系泊系统3部分的内孤立波作用力叠加到外力项中,联合求解半潜式平台的6自由度动力响应特性。数值模拟结果表明,在内孤立波作用下,半潜式平台的运动及系泊线张力均受到了显著的影响。在不考虑系泊系统受内孤立波作用时,平台在纵荡和横荡方向上产生较大的漂移运动,最大偏移量较无内孤立波情况下增加了8倍;系泊线最大张力提高了17%,增加了系泊线断裂的风险。在考虑系泊系统受内孤立波作用时,平台的纵荡和横荡运动响应在原响应基础上继续提高15%,但是系泊线张力变化不大。内孤立波不同浪向下的平台纵荡和横荡响应相差也很明显;系泊系统合力在不同方向上的大小决定了平台不同方向上运动的大小。     

一种新型Semi-Spar式海上风机平台系泊系统优化分析

参考英国的Kincardine风机采用的新式的Semi-Spar概念,结合spar式基础和半潜式基础的特点,提出了一种新式海上浮式风机平台模型,并基于三维势流理论,利用AQWA软件进行水动力计算,验证新式平台可靠性。分析了在风、浪、流荷载联合作用下,锚链竖向夹角、系缆数量对风机浮式平台运动性能和系泊张力的影响,对系泊系统进行优化,并验证极端工况下的可靠性。结果证明风机平台水平运动和纵摇运动幅值较小,但垂荡幅值略大,而通过减小锚链竖向夹角可以控制平台运动响应幅值,增加系缆数量可以同时减小系泊张力大小。计算结果证明了新型Semi-Spar式海上风机平台可行性,为浮式风机平台及系泊系统的设计提供参考。     

立管对深水半潜式生产平台定位性能影响研究

基于三维频域势流理论,计算船体的水动力参数;采用动态耦合方法分析了深海半潜式生产平台各系统之间的相互作用特征,研究了立管系统对锚泊系统定位能力的影响。计算结果表明,立管系统在一定程度上增加了整个系统的刚度,其所受的附加质量和阻尼可降低平台的低频响应,从而降低平台的偏移和系泊缆的张力;海流将增大立管上的拖曳力,使平台偏移更远,锚索上的张力更大;立管系统对锚泊系统定位性能的最终影响需综合考虑多种因素的叠加。对目标平台而言,由于服役海域的流速较大,对立管的拖曳作用较为明显。因此,为确保平台的安全性,当服役海域流速较大时,带有多立管的平台,其锚泊系统的设计应考虑立管的影响。     

深水半潜式平台锚链倾角监测的自容式传感器的设计

深水半潜式平台系泊锚链的倾角变化是评价平台系泊状态与锚链受力的重要指标,是半潜式平台重要的监测内容。目前,深水锚链的测量主要是采用自容式的传感器,针对其水下长时间测量的应用特点,要求它的设计必须具有低功耗、高可靠性、大存储量、体积小、防水耐压等指标。根据我国南海流花平台的锚链监测需要,设计与制作了专用的水下自容式倾角传感器,并在实际应用中进行了检验。     

Sensitivity Analysis of Air Gap Motion with Respect to Wind Load and Mooring System for Semi-Submersible Platform Design

A design of semi-submersible platform is mainly based on the extreme response analysis due to the forces experienced by the components during lifetime. The external loads can induce the extreme air gap response and potential deck impact to the semi-submersible platform. It is important to predict air gap response of platforms accurately in order to check the strength of local structures which withstand the wave slamming due to negative air gap. The wind load cannot be simulated easily by model test in towing tank whereas it can be simulated accurately in wind tunnel test. Furthermore, full scale simulation of the mooring system in model test is still a tuff work especially the stiffness of the mooring system. Owing to the above mentioned problem, the model test results are not accurate enough for air gap evaluation. The aim of this paper is to present sensitivity analysis results of air gap motion with respect to the mooring system and wind load for the design of semi-submersible platform. Though the model test results are not suitable for the direct evaluation of air gap, they can be used as a good basis for tuning the radiation damping and viscous drag in numerical simulation. In the presented design example, a numerical model is tuned and validated by ANSYS AQWA based on the model test results with a simple 4 line symmetrical horizontal soft mooring system. According to the tuned numerical model, sensitivity analysis studies of air gap motion with respect to the mooring system and wind load are performed in time domain. Three mooring systems and five simulation cases about the presented platform are simulated based on the results of wind tunnel tests and sea-keeping tests. The sensitivity analysis results are valuable for the floating platform design.     

绷紧式系泊缆冲击张力特性研究

采用集中质量法研究了绷紧式系泊系统中系缆由于松弛-张紧过程产生的冲击张力。建立系泊缆绳离散的集中质量模型,对其独立单元进行受力分析并建立了单元的运动方程。给定缆绳上端点简谐激励,通过Ansys中的Aqwa模块,分析了缆绳的运动响应;针对缆绳运动响应过程中的三种状态进行了模拟计算,探讨了冲击张力产生的条件;研究了缆绳初始预张力、上端点激励幅值和频率、拖曳力系数、弹性模量以及单位长度质量对动态张力的影响。研究结果表明:这些影响因素不仅会影响缆绳动态张力的大小,也会对缆绳中的冲击张力产生一定的影响。     

畸形波作用下半潜浮式风机系泊失效停机响应分析

半潜浮式风机逐渐在深海风电开发中受到关注,建立风机、平台与系泊结构耦合数值计算模型,通过FAST与AQWA链接进行风机塔基荷载及平台运动响应相互耦合传递,基于随机波与极限波组合模型生成畸形波时程序列,进行半潜浮式风机系泊失效全过程时域模拟计算分析,得出系泊锚链张力、风机、塔筒和平台运动时程响应,探究系泊失效、风机停机和叶片变桨速率对浮式风机平台系泊结构动力响应的影响。结果表明：畸形波作用下浮式平台和系泊结构动力响应显著,系泊失效导致塔基剪力增加,平台纵荡和纵摇运动响应显著增大;风机停机会引起系泊锚链张力显著减小,转子推力、塔基剪力和叶尖挥舞位移响应逐渐衰减,平台纵荡、纵摇和横摇运动响应显著减小;随着叶片变桨速率增加,风机转子推力和塔基剪力波动幅值增大。     

Dynamics of large-truncated mooring systems coupled with a catenary moored semi-submersible

With the floating structures pushing their activities to the ultra-deep water,model tests have presented a challenge due to the limitation of the existing wave basins.Therefore,the concept of truncated mooring system is implemented to replace the full depth mooring system in the model tests,which aims to have the same dynamic responses as the full depth system.The truncated mooring system plays such a significant role that extra attention should be paid to the mooring systems with large truncation factor.Three different types of large truncation factor mooring system are being employed in the simulations,including the homogenously truncated mooring system,non-homogenously truncated mooring system and simplified truncated mooring system.A catenary moored semi-submersible operating at 1000 m water depth is presented.In addition,truncated mooring systems are proposed at the truncated water depth of 200 m.In order to explore the applicability of these truncated mooring systems,numerical simulations of the platform’s surge free decay interacting with three different styles of truncated mooring systems are studied in calm water.Furthermore,the mooring-induced damping of the truncated mooring systems is simulated in the regular wave.Finally,the platform motion responses and mooring line dynamics are simulated in irregular wave.All these simulations are implemented by employing full time domain coupled dynamic analysis,and the results are compared with those of the full depth simulations in the same cases.The results show that the mooring-induced damping plays a significant role in platform motion responses,and all truncated mooring systems are suitable for model tests with appropriate truncated mooring line diameters.However,a large diameter is needed for simplified truncated mooring lines.The suggestions are given to the selection of truncated mooring system for different situations as well as to the truncated mooring design criteria.     

Fundamental analysis of deep sea mooring line in static equilibrium

The integrated equations of deep sea mooring lines in static equilibrium under consideration of gravity force and line elongation are obtained. The most useful forms of the equations for designing deep sea mooring system are those in which horizontal displacement and horizontal and vertical components of tension are obtained as functions of line length, water depth, critical tension and unit weight of line.When the dynamic simulation of a buoy system is carried out, line tensions acting on the buoy should be represented as a linear function of displacement. Therefore the linearisation method is introduced by use of linearisation coefficient matrix. Translation formulae for the matrix from two to three dimensions is also presented.The influence of line elongation on the horizontal component of tension in a taut mooring condition is important, therefore the elongation of stretched deep sea mooring line must be considered carefully. Also, the scaling law under consideration of line elongation in static equilibrium, which is necessary in estimation from a small sized experiment, is discussed.     

超大型和大型半潜浮式海上风力机动力响应对比

以超大型风力机(DTU 10 MW)为研究对象,对现有的大型(NREL 5 MW)无撑杆半潜浮式风力机支撑平台进行放大设计,用于支撑超大型风力机,基于气动-水动-伺服-弹性全耦合计算模型,根据设定的典型工况,使用FAST软件对超大型和大型无撑杆的半潜浮式风力机系统进行时域耦合分析,并依据计算结果对超大型和大型浮式风力机系统的运动响应和结构动力反应等特性进行对比分析。研究发现:半潜浮式风力机大型化后,气动荷载效应对风力机系统的激励作用更为突出,使得浮式平台运动由风荷载激励的低频共振反应比例增大,波频运动比例减小,这也导致由浮式平台低频运动激励的锚链张力反应增大。此外,高倍的飞轮转动频率对大型半潜浮式风力机叶片、塔架结构的激励作用较超大型半潜浮式风力机更为显著。     

Dynamic behavior of offshore spar platforms under regular sea waves

Many innovative floating offshore structures have been proposed for cost effectiveness of oil and gas exploration and production in water depths exceeding one thousand meters in recent years. One such type of platform is the offshore floating Spar platform. The Spar platform is modelled as a rigid body with six degrees-of-freedom, connected to the sea floor by multi-component catenary mooring lines, which are attached to the Spar platform at the fairleads. The response dependent stiffness matrix consists of two parts (a) the hydrostatics provide restoring force in heave, roll and pitch, (b) the mooring lines provide the restoring force which are represented here by nonlinear horizontal springs. A unidirectional regular wave model is used for computing the incident wave kinematics by Airy’s wave theory and force by Morison’s equation. The response analysis is performed in time domain to solve the dynamic behavior of the moored Spar platform as an integrated system using the iterative incremental Newmark’s Beta approach. Numerical studies are conducted for sea state conditions with and without coupling of degrees-of-freedom.     

Nonlinear coupled dynamic response of offshore Spar platforms under regular sea waves

Many innovative floating offshore structures have been proposed for cost effectiveness of oil and gas exploration and production in water depths exceeding one thousand meters in recent years. One such type of platform is the offshore floating Spar platform. The Spar platform is modelled as a rigid body with six degrees-of-freedom, connected to the sea floor by multi-component catenary mooring lines, which are attached to the Spar platform at the fairleads. The response dependent stiffness matrix consists of two parts (a) the hydrostatics provide restoring force in heave, roll and pitch, (b) the mooring lines provide the restoring force which are represented here by nonlinear horizontal springs. A unidirectional regular wave model is used for computing the incident wave kinematics by Airy’s wave theory and force by Morison’s equation. The response analysis is performed in time domain to solve the dynamic behavior of the moored Spar platform as an integrated system using the iterative incremental Newmark’s Beta approach. Numerical studies are conducted for sea state conditions with and without coupling of degrees-of-freedom.