On Simulation and Analysis of Variable‐Rate Pumping Tests

Analytical solutions for constant‐rate pumping tests are widely used to infer aquifer properties. In this note, we implement a methodology that approximates the time‐varying pumping record as a series of segments with linearly varying pumping rates. We validate our approach using an analytical solution for a sinusoidally varying pumping test. We also apply our methodology to analyze synthetic test data and compare the results with those from a commonly used method where rate variations are represented by a series of constant‐rate steps.     

Conducting Slug Tests in Mini‐Piezometers

Slug tests performed using mini‐piezometers with internal diameters as small as 0.43 cm can provide a cost effective tool for hydraulic characterization. We evaluated the hydraulic properties of the apparatus in a laboratory environment and compared those results with field tests of mini‐piezometers installed into locations with varying hydraulic properties. Based on our evaluation, slug tests conducted in mini‐piezometers using the fabrication and installation approach described here are effective within formations where the hydraulic conductivity is less than 1 × 10^?3 cm/s. While these constraints limit the potential application of this method, the benefits to this approach are that the installation, measurement, and analysis is cost effective, and the installation can be completed in areas where other (larger diameter) methods might not be possible. Additionally, this methodology could be applied to existing mini‐piezometers previously installed for other purposes. Such analysis of existing installations could be beneficial in interpreting previously collected data (e.g., water‐quality data or hydraulic head data).     

高土石坝振动台模型试验理论、技术与应用

对土石坝振动台模型试验理论和技术进行系统阐述,提出基于原型和模型坝料静、动力特性试验的模型相似设计方法和不同强度地震动递进输入(白噪声微振-设计地震-校核地震-破坏试验)的振动试验方法。基于1g大型振动台和ng超重力离心机振动台设备性能现状,结合高土石坝的结构特点和动力试验相似模拟要求,对土石坝振动台模型试验的优势及局限进行深入讨论。结合已有的工程实践,对土石坝振动台模型试验在工程中的应用进行总结,并以某实际高面板堆石坝为例研究面板坝生命周期内经历多次地震情况下结构动力特性的演化规律。     

Tests on low‐ductility RC frames under high‐ and low‐frequency excitations

The response of low‐ductility reinforced concrete (RC) frames, designed typically for a non‐seismic region, subjected to two frequencies of base excitations is studied. Five half‐scaled, two‐bay, two‐storey, RC frames, each approximately 5 m wide by 3.3 m high, were subjected to both horizontal and/or vertical base excitations with a frequency of 40 Hz as well as a lower frequency of about 4 Hz (close to the fundamental frequency) using a shake table. The imposed acceleration amplitude ranged from 0.2 to 1.2g. The test results showed that the response characteristics of the structures differed under high‐ and low‐frequency excitations. The frames were able to sustain high‐frequency excitations without damage but were inadequate for low‐frequency excitations, even though the frames exhibited some ductility. Linear‐elastic time‐history analysis can predict reasonably well the structural response under high‐frequency excitations. As the frames were not designed for seismic loads, the reinforcement detailing may not have been adequate, based on the crack pattern observed. The effect of vertical excitation can cause significant additional forces in the columns and moment reversals in the beams. The ‘strong‐column, weak‐beam’ approach for lateral load RC frame design is supported by experimental observations. Copyright © 2001 John Wiley & Sons, Ltd.     

Analytical and Semi‐Analytical Tools for the Design of Oscillatory Pumping Tests

Oscillatory pumping tests—in which flow is varied in a periodic fashion—provide a method for understanding aquifer heterogeneity that is complementary to strategies such as slug testing and constant‐rate pumping tests. During oscillatory testing, pressure data collected at non‐pumping wells can be processed to extract metrics, such as signal amplitude and phase lag, from a time series. These metrics are robust against common sensor problems (including drift and noise) and have been shown to provide information about aquifer heterogeneity. Field implementations of oscillatory pumping tests for characterization, however, are not common and thus there are few guidelines for their design and implementation. Here, we use available analytical solutions from the literature to develop design guidelines for oscillatory pumping tests, while considering practical field constraints. We present two key analytical results for design and analysis of oscillatory pumping tests. First, we provide methods for choosing testing frequencies and flow rates which maximize the signal amplitude that can be expected at a distance from an oscillating pumping well, given design constraints such as maximum/minimum oscillator frequency and maximum volume cycled. Preliminary data from field testing helps to validate the methodology. Second, we develop a semi‐analytical method for computing the sensitivity of oscillatory signals to spatially distributed aquifer flow parameters. This method can be quickly applied to understand the “sensed” extent of an aquifer at a given testing frequency. Both results can be applied given only bulk aquifer parameter estimates, and can help to optimize design of oscillatory pumping test campaigns.     

Mechanism of Liquefaction Response in Sand–Silt Dynamic Centrifuge Tests

The process of dynamically induced liquefaction in two centrifuge soil models is analyzed. These models consist of saturated medium-dense sand overlain by a low permeability silt deposit, and represent prototypes of a level site and an embankment. The recorded lateral accelerations are employed to evaluate shear stress and strain histories at different elevations within the tested soil systems. These histories shed light on the involved liquefaction process, and the associated mechanisms of: (1) lateral deformation; (2) stiffness and strength degradation; and (3) possible densification and regain of stiffness, thereafter. The identified response patterns are found comparable to those documented by laboratory cyclic-loading tests.     

Comparison of Hydraulic Conductivity Values Obtained from Aquifer Pumping Tests and Conservative Tracer Tests

Afield site was established in an area of glacial outwash near Des Moines, Iowa. Hydraulic conductivity (K) of the outwash was measured in various ways including six pumping tests and two natural-gradient Cl^- tracer tests. The velocity of the conservative tracer was converted to K using measured gradients and effective porosity determined from two radial-convergent Cl^- tracer tests.
K values measured from the conservative tracer tests are approximately one-tenth to one-twentieth the average pumping-test value. Thus the K relevant to solute transport does not reflect the K measured by pumping tests. This discrepancy may be caused by the different scale and dimensionality of the two test types. Dispersion may prevent solutes from flowing exclusively within smaller high-conductivity paths which strongly affect the K measured by pumping tests.     

Modeling Transient Streaming Potentials in Falling‐Head Permeameter Tests

We present transient streaming potential data collected during falling‐head permeameter tests performed on samples of two sands with different physical and chemical properties. The objective of the work is to estimate hydraulic conductivity (K) and the electrokinetic coupling coefficient (C_l) of the sand samples. A semi‐empirical model based on the falling‐head permeameter flow model and electrokinetic coupling is used to analyze the streaming potential data and to estimate K and C_l. The values of K estimated from head data are used to validate the streaming potential method. Estimates of K from streaming potential data closely match those obtained from the associated head data, with less than 10% deviation. The electrokinetic coupling coefficient was estimated from streaming potential vs. (1) time and (2) head data for both sands. The results indicate that, within limits of experimental error, the values of C_l estimated by the two methods are essentially the same. The results of this work demonstrate that a temporal record of the streaming potential response in falling‐head permeameter tests can be used to estimate both K and C_l. They further indicate the potential for using transient streaming potential data as a proxy for hydraulic head in hydrogeology applications.     

Tests of the random network model,and its application to basin hydrology

If the random model, in which all topologically distinct channel networks are equally likely, is assumed valid, then general explanations of network structure from basin geomorphic processes cannot be expected. Tests for the random model are therefore critical to the direction of future work. Proposed tests are based on frequencies of basins of different magnitudes or diameters, and on network maximum widths. Network topology is also shown to be potentially significant in the prediction of basin hydrographs. Network width commonly varies by a factor of 2 × for a given drainage area and drainage density, and is shown to influence peak discharge in proportion. Lag-to-peak can also be predicted better, using network topology. The paper pursues these applications of network topology using random walk theory and simulated random networks.     

Push‐Pull Tests for Estimating RDX and TNT Degradation Rates in Groundwater

In situ bioremediation is being considered to optimize an existing pump‐and‐treat remedy for treatment of explosives‐contaminated groundwater at the Umatilla Chemical Depot. Push‐pull tests were conducted using a phased approach to measure in situ hexahydro‐1,3,5‐trinitro‐1,3,5‐triazine (RDX) and 2,4,6‐trinitrotoluene (TNT) degradation rates associated with various carbon substrates. Phase I included short‐duration transport tests conducted in each well to determine dilution rates and retardation factors for RDX and TNT. Phase II included aquifer “feedings” conducted by injecting 150 gallons of treated site groundwater amended with ethanol, corn syrup, lactose or emulsified oil (concentrations 10, 25 and 27 mM, respectively; 12% by volume for emulsified oil). Wells received up to 6 substrate “feedings” over the course of 3 months followed by monitoring dissolved oxygen, nitrate, Fe(II), and sulfate to gauge in situ redox conditions as indicators of anaerobic microbial activity. Phase III included push‐pull tests conducted by injecting 150 gallons of site groundwater amended with approximately 1000 µg/L RDX, 350 µg/L TNT, carbon substrate and a conservative tracer, followed by sampling over 8 d. Corn syrup resulted in the best RDX removal (82% on average) and the largest RDX degradation rate coefficient (1.4 ± 1.1 d^?1). Emulsified oil resulted in the best TNT removal (99%) and largest TNT degradation rate coefficient (5.7 × 10^?2 d^?1). These results will be used to simulate full‐scale in situ bioremediation scenarios at Umatilla and will support a go/no‐go decision to initiate full‐scale bioremediation remedy optimization.     

Cone Penetrometer Tests and HydroPunch® Sampling: A Screening Technique for Plume Definition

Cone penetrometer tests and HydroPunch® sampling were used to define the extent of volatile organic compounds in ground water. The investigation indicated that the combination of these techniques is effective for obtaining ground water samples for preliminary plume definition. HydroPunch samples can be collected in unconsolidated sediments and the analytical results obtained from these samples are comparable to those obtained from adjacent monitoring wells. This sampling method is a rapid and cost-effective screening technique for characterizing the extent of contaminant plumes in soft sediment environments. Use of this screening technique allowed monitoring wells to be located at the plume boundary, thereby reducing the number of wells installed and the overall cost of the plume definition program.