边坡落石运动轨迹计算新方法

考虑落石形状对落石运动轨迹的影响,将落石近似成椭圆形。根据落石运动的5种常见形式,即自由落体运动、斜抛运动、碰撞、滑动和滚动,分别得到了各种运动形式的运动速度计算公式。在碰撞阶段考虑了地面的弹塑性变形,得到了与碰撞前速度、落石形状和地面材料有关的恢复系数计算公式,并根据接触力学的有关理论得到了碰撞冲击力的计算公式,给出了落石连续滚动的判别条件。将理论公式应用于重庆万州首立山落石运动轨迹预测,验证了理论公式的可行性和有效性。     

边坡落石灾害的颗粒流模拟方法

落石是边坡的一种常见的动力地质灾害。基于颗粒流理论,提出了落石灾害的二维的可视化模拟方法。通过颗粒流中不同参数的ball单元的组合模拟了各种形状和特性的落石体;通过wall单元的组合模拟坡面;选择ball-ball和ball-wall的接触刚度模型、粘结模型和滑移模型等接触本构模型来反映落石运动过程中落石岩块内部各部分和落石与坡面作用行为;实现了边坡落石灾害的二维可视化模拟。模型模拟出落石的自由落体、弹跳、滑动和滚动等运动形式、运动过程岩块的崩解;得到了落石的运动速度、位移等运动学参数。工程实例初步验证了该方法的可行性、合理性。     

鄂西山区崩塌落石运动特征及危险性分析

以远安县瓦坡崩塌区为例,通过地质调查、野外测绘、无人机航拍,建立了瓦坡崩塌区三维模型,基于Rockfall Analyst（RA）分析软件,实现了瓦坡崩塌区大量崩塌落石三维空间下运动路径、高度、能量等要素模拟,探究了崩塌区落石的三维运动特征,开展了崩塌区落石危险性评估,为崩塌落石的防治提供科学参考。研究结果表明:崩塌区危岩主要破坏形式为倾倒式,目前处于欠稳定状态;模拟落石三维运动轨迹与已有落石点基本重合,说明此次模拟结果与实际情况较为吻合;落石运动过程中以碰撞弹跳、自由飞落为主,落石主要集中在崩塌区下部冲沟及公路内,部分落石达到居民区,在崩塌落石区下部公路、冲沟及崩塌区右侧危险性较高;崩塌落石防治工程建议采用危石孤石清除+被动防护网,在公路内侧、斜坡下方分别设置5 m高和3 m高抗冲击力2 000 kJ的被动防护网,可有效拦截落石。     

非均一性斜坡落石运动轨迹

现有的落石运动轨迹研究均将斜坡视为半无限均匀的坡面,而实际的工况下,坡面由不均一材料组成.根据落石不同的运动模式,将坡面简化为多层岩土体材料的结构形式,在滚动阶段,基于Hertz接触理论得到落石在不同坡面条件下运动特征,并给出坡面分层条件下落石切向摩擦系数的计算公式,在碰撞阶段,基于能量守恒定理,采用准静态接触力学理论...     

基于运动特征分析的高陡边坡崩塌落石防治措施建议

崩塌落石具有突发性、随机性、隐蔽性及致灾严重性等特征。为对其进行有效防治,以某煤矿内崩塌落石为研究对象,采用RocFall软件对已崩落石的运动轨迹进行了模拟,反演拟合了下垫面参数,在此基础对拟崩落石区域进行数值模拟和理论计算得出其运动特征,为崩塌落石防治措施选择提供了合理依据。     

基于崩塌滚石运动特征的防护网动态响应规律

为获取被动柔性防护网在不同崩塌滚石运动特征下的动态响应规律,以鲁甸803地震震后崩塌滚石造成防护网损坏现场为例,通过无人机倾斜摄影技术实现地质调查,采用Rockyfor3D获取研究区落石的运动特征,并通过被动柔性防护网有限元模型,对不同落石冲击形式下防护网的动态响应规律进行研究.研究显示区内落石弹跳高度普遍在1~2 m,优势路径上的落石会形成稍高速低弹跳的范围冲击.在范围落石冲击下,防护网绳索最大拉力增加可达123.7%;在低弹跳落石冲击下,绳索最大拉力增加可达181.2%.范围落石冲击会导致防护网网面耗能的降低,并导致上拉锚绳拉力的增大.防护网下一级支撑绳对不同落石弹跳高度的响应较为敏感,部分高弹跳落石会对上拉锚绳和上一级支撑绳产生影响.      

地震荷载下危岩运动特征的模拟研究

西南地区地形复杂,位于地震高发区域。为了进一步研究该区域地震作用下落石的运动特征,以我国九寨沟景区内荷叶寨后山危岩带2为例。首先研究危岩带2中单一危岩体在自重荷载下的失稳情况,分别采用RocFall和非连续变形分析方法(DDA)进行模拟,结果表明:DDA和RocFall的模拟结果相近。DDA中落石水平位移模拟结果为210.6 m,RocFall中大部分落石水平位移分布在205 m附近。鉴于RocFall的局限性,采用DDA方法继续研究地震作用下危岩体的密度、高度、体积和地震波峰值加速度等因素对落石运动特征如运动轨迹、水平位移和速度的影响规律,并监测落石在坡脚附近的最大弹跳高度。研究结果表明:(1)危岩带2所处边坡自然坡角范围为65°~75°,落石在坡面上加速,在高程约2292 m(与居民区相对高差约为132 m)处发生抛射,运动方式以滚动、碰撞、弹跳为主;(2)岩体软弱结构面的贯通时间随落石密度、体积以及地震波峰值加速度增大而减小;(3)峰值速度随边坡高度、体积及地震波峰值加速度增大而增大;(4)水平位移随落石密度、边坡高度及地震波峰值加速度增大而增大;(5)坡脚处落石最大弹跳高度随各因素变量增大而增大。继续研究内部存在节理裂隙的岩体(3条平行节理将危岩分为K1~K4部分)在地震荷载下的运动特征:(1)在地震荷载作用下,危岩沿节理面发生倾倒破坏,落石水平位移模拟结果为191.5~243.8 m;(2)落石在坡脚附近的最大弹跳高度范围为0~13.8 m。     

融合区域潜在落石源区识别的峡谷区落石危险性评价

山西壶关太行山大峡谷景区为中国最美十大峡谷之一,但景区落石灾害频发,严重威胁景区安全运营。本文基于高精度地形信息与岩土体强度特性,采用坡度角分布方法开展区域尺度潜在落石源区识别,并引入岩体破坏敏感性指标定量描述潜在落石源区失稳概率。然后,利用经验模型Flow-R模拟落石运动扩散过程,获取落石的传播概率与能量分布情况。最后,提出落石危险性双因子评价模型实现落石危险性定量评估。获得主要结论如下:(1)研究区内潜在落石源区面积为25.7 km2(35.7%),主要以条带状分布于峡谷两侧陡壁。其中岩体破坏高敏感性区为3.3 km2。(2)研究区落石高危险区面积达3.22 km2,主要威胁景区内游客集散地与交通线路,尤其在S327荫林线红豆峡入口处落石危险性最高。(3)野外调查验证结果表明了应用坡度角分布方法识别潜在落石源区的高效性与准确性,提出的双因子评价模型可为峡谷区落石危险性评估提供快速解决方案。本文提出的“区域落石源区识别-源区失稳概率分析-落石危险性评估”的一整套技术方案能够为类似的高山峡谷区落石灾害早期识别及风险防控提供技术参考。     

崩塌落石运动计算模型综述

由于崩塌落石的广泛分布及其发育地的地质条件与地理环境的复杂性和特殊性使得对其进行较为全面的研究治理颇为困难。虽然近年来对崩塌落石的研究有了较多的成果,但目前对其运动的计算模型还存在问题,在很大程度上制约了防灾减灾科学的进展。为了深入探讨崩塌落石的运动计算模型,本文回顾了国内学者在相关领域的研究,系统总结了现有计算模型的研究现状,且对计算模型进行了讨论和总结。     

桂林穿山公园西侧危岩体破坏机制及治理

桂林市穿山公园西侧存在的危岩隐患共有数十处,根据危岩体结构特征和变形破坏迹象,分析了危岩体的3种破坏机制:拉裂―滑移式、拉裂―坠落式、拉裂―倾倒式三种基本类型。在此基础上,运用能量守恒定律和运动学规律研究危岩体失稳落石运动特征。结合RocFall软件对落石运动进行模拟计算,对崩塌落石的途径、方向、跳跃高度,影响范围进行验证,与理论计算结果吻合。结合施工条件,采用清除浮土及危石,岩壁上安装SNSGPS2主动防护网加固,坡脚安装SNSRX050被动防护网来拦截落石,确保公园内游客安全。     

Rockfall susceptibility zoning based on back analysis of rockfall deposit inventory in Gunung Kelir,Java

A rockfall susceptibility based on trajectory-energy/velocity approach needs release area or rockfall source. However, identification of rockfall source is not always possible for some areas in Indonesia. This paper presents a rockfall susceptibility zoning based on back analysis technique of rockfall deposit inventory in Gunung Kelir, Java. There were several steps in the rockfall susceptibility zoning: (1) rockfall deposit inventory, (2) rockfall simulation based on back analysis of rockfall deposit inventory, (3) sensitivity analysis, and (4) rockfall susceptibility zoning. The result suggests that the travel distance is affected by the spatial distribution of rockfall source, lithology or surface material, and topography (angle of slope and angle of aspect). Final trajectories were employed to generate landslide susceptibility map which may allow a policy maker to have an advanced consideration to achieve specified risk measures and evaluation of their cost efficiency to optimize budget and design. Application of rockfall susceptibility zoning based on back analysis of rockfall deposits is efficient where rockfall source information is unavailable.     

Multi-scenario Rockfall Hazard Assessment Using LiDAR Data and GIS

Transportation corridors that pass through mountainous or hilly areas are prone to rockfall hazard. Rockfall incidents in such areas can cause human fatalities and damage to properties in addition to transportation interruptions. In Malaysia, the North–South Expressway is the most significant expressway that operates as the backbone of the peninsula. A portion of this expressway in Jelapang was chosen as the site of rockfall hazard assessment in multiple scenarios. Light detection and ranging techniques are indispensable in capturing high-resolution digital elevation models related to geohazard studies. An airborne laser scanner was used to create a high-density point cloud of the study area. The use of 3D rockfall process modeling in combination with geographic information system (GIS) is a beneficial tool in rockfall hazard studies. In this study, a 3D rockfall model integrated into GIS was used to derive rockfall trajectories and velocity associated with them in multiple scenarios based on a range of mechanical parameter values (coefficients of restitution and friction angle). Rockfall characteristics in terms of frequency, height, and energy were determined through raster modeling. Analytic hierarchy process (AHP) was used to compute the weight of each rockfall characteristic raster that affects rockfall hazard. A spatial model that considers rockfall characteristics was conducted to produce a rockfall hazard map. Moreover, a barrier location was proposed to eliminate rockfall hazard. As a result, rockfall trajectories and their characteristics were derived. The result of AHP shows that rockfall hazard was significantly influenced by rockfall energy and then by frequency and height. The areas at risk were delineated and the hazard percentage along the expressway was observed and demonstrated. The result also shows that with increasing mechanical parameter values, the rockfall trajectories and their characteristics, and consequently rockfall hazard, were increased. In addition, the suggested barrier effectively restrained most of the rockfall trajectories and eliminated the hazard along the expressway. This study can serve not only as a guide for a comprehensive investigation of rockfall hazard but also as a reference that decision makers can use in designing a risk mitigation method. Furthermore, this study is applicable in any rockfall study, especially in situations where mechanical parameters have no specific values.     

丰都名山崩滑体失稳的离散元模拟

以丰都名山崩滑体为研究对象,拟通过对该崩滑体失稳破坏过程的离散元模拟分析,达到对该崩滑体的稳定性进行有效分析评价的目的。研究结果发现,崩滑体的滑移崩塌过程及散落情况与其坡脚是否风化剥蚀相关,且不论坡脚是否风化剥蚀,其上部块体的运动轨迹与中下部块体的运动轨迹存在着明显差异。分析结果同时还表明,丰都名山崩滑体的确存在滑移崩塌危险,应积极采取适当防范措施。     

基于线黏弹性接触的落石冲击地面参量理论研究

落石与坡面或者防护结构接触过程中冲击参量随时间变化特征是描述落石碰撞过程的重要指标,对于揭示落石与坡面相互作用机制以及采取合理的防护措施具有重要的意义。在现有的相关设计规范中,并没有给出关于落石冲击力时程关系的计算方法,仅参照有关规范或经验方法确定一个落石最大冲击力值。为此,首先基于线黏弹性接触理论,建立落石冲击地面力学模型,根据位移-速度组合初始条件以及速度-加速度组合初始条件分别推导得到两种落石冲击特征参量理论解析解;然后基于 ANSYS/LS-DYNA 非线性动力学软件,建立落石冲击地面三维数值模型,研究球体落石冲击地面力学特点;最后将理论结果对比室内试验和已有的研究成果,得出以下结论：（1）Hertz 弹性接触理论结果中各参量变化在加载阶段和恢复阶段均呈现对称的趋势,速度、加速度初始条件下的落石冲击特征参量和动力有限元法非常接近,而位移-速度初始条件组合并不适用于研究落石冲击下的动力特征;（2）不同速度和下落高度下,落石最大冲击力值随落石下落高度和冲击速度的增大而增加,而落石冲击作用时间随下落高度和冲击速度的增加而减小;（3）计算结果得到的落石最大冲击力以及落石冲击作用时间与室内试验结果和已有成果相接近,相比室内试验和有限元结果的震荡性,此结果更能体现落石冲击力变化规律; （4）多种冲击速度下,对比不同方法得到的落石最大冲击力,可知计算结果均在各种冲击力计算结果的范围内,具有很好的可靠性。考虑到现有研究理论的不足,难以求解落石冲击力时程关系,求解结果丰富了落石碰撞理论,可以指导工程有关落石灾害的防护设计。     

Comparison of rockfall susceptibility assessment at local and regional scale: a case study in the north of Beijing (China)

This study shows a rockfall susceptibility assessment at local scale in north Beijing of China, including the identification of rockfall sources onsite by terrain and rock discontinuities analysis and run-out distance prediction by Rocfall^? simulation. Two types of rockfall were defined including one type on the cliffs with long inclined slopes and another type on the road slopes with low height. Two historical rockfall events were used to back-calibrating the parameters used for run-out distance simulation. Based on the work, rockfall susceptibility map at local scale was created in GIS, which was compared with the map obtained at regional scale (entire Huairou district scale). Due to the difference of approaches applied, procedure of assessment and types of source data acquired, the two resulting rockfall susceptibility maps are proved to be different. Still, both of them are useful and could be used at different level’s decision for rockfall prevention and mitigation. Different types of uncertainties exist in the study of rockfall susceptibility assessment. To reduce the uncertainties, studies on both approaches and techniques are suggested.     

落石冲击混凝土棚洞力学特性研究

落石冲击棚洞结构作用过程复杂,缺乏统一的落石冲击力表达式。首先,将落石简化为刚性球体,基于Hertz接触理论,推导得到落石冲击力半正弦算法的理论表达式,考虑落石冲击下棚洞的非弹性特征,根据落石与材料碰撞过程中落石加速度曲线特征,采用函数拟合法推导得到落石法向冲击下其冲击力的理论计算方法;然后,基于ANSYS/LS-DYNA软件建立落石冲击棚洞数值计算模型,研究不同冲击速度下落石冲击棚洞动力特征;最后,与现存常见的多种方法进行对比,得出以下结论：Hertz半正弦法得到的落石冲击力远大于函数拟合法和数值法,而函数拟合法和数值法得到的落石冲击力时程曲线相接近,表明函数拟合法更能反映落石与棚洞接触碰撞动力关系;对比其他计算方法可以得到,Hertz算法适用于分析无能量损失下的弹性碰撞问题,而Logistic算法适用于材料大塑性变形的情况,弹塑性接触理论结果和动力有限元结果存在差异,而采用函数拟合推导的计算方法得到的落石最大冲击力和落石冲击作用时间与动力有限元法更接近,更能反映落石冲击棚洞动力响应特征,推导的落石冲击力计算方法可为工程实践中棚洞防护设计提供理论参考。     

Assessing rockfall susceptibility in steep and overhanging slopes using three-dimensional analysis of failure mechanisms

Rockfalls strongly influence the evolution of steep rocky landscapes and represent a significant hazard in mountainous areas. Defining the most probable future rockfall source areas is of primary importance for both geomorphological investigations and hazard assessment. Thus, a need exists to understand which areas of a steep cliff are more likely to be affected by a rockfall. An important analytical gap exists between regional rockfall susceptibility studies and block-specific geomechanical calculations. Here we present methods for quantifying rockfall susceptibility at the cliff scale, which is suitable for sub-regional hazard assessment (hundreds to thousands of square meters). Our methods use three-dimensional point clouds acquired by terrestrial laser scanning to quantify the fracture patterns and compute failure mechanisms for planar, wedge, and toppling failures on vertical and overhanging rock walls. As a part of this work, we developed a rockfall susceptibility index for each type of failure mechanism according to the interaction between the discontinuities and the local cliff orientation. The susceptibility for slope parallel exfoliation-type failures, which are generally hard to identify, is partly captured by planar and toppling susceptibility indexes. We tested the methods for detecting the most susceptible rockfall source areas on two famously steep landscapes, Yosemite Valley (California, USA) and the Drus in the Mont-Blanc massif (France). Our rockfall susceptibility models show good correspondence with active rockfall sources. The methods offer new tools for investigating rockfall hazard and improving our understanding of rockfall processes.     

边坡滚石运动轨迹分段循环算法

边坡滚石是在基本建设中常遇到的一种工程灾害。其防护结构的设计依据主要是边坡滚石的运动轨迹,因而要对这种灾害进行防治,首先要确定滚石的运动轨迹。根据落石运动全过程的三个阶段,即滚动(滑动)运动阶段、抛物运动阶段和与坡面碰撞阶段,利用分段循环算法分别得到了三个运动阶段的运动速度计算公式。以某岩质边坡构建相似模型,将该理论公式应用于落石运动轨迹预测,验证了公式的可行性和有效性。与现有方法相比,分段循环算法具有计算原理简单明确、易于使用等优点。该方法可用于斜坡区滚石运动特征的预测,并可作为斜坡区滚石灾害防治的依据。     

尼泊尔某项目滚石灾害的工程地质调查与评价

滚石灾害是山区常见的地质灾害类型,研究滚石的运动特征对地质灾害调查及危险性评估有着重要意义.通过对尼泊尔某项目滚石灾害后现场进行工程地质调查,分析其灾害成因机制,查明事故原因.调查结果表明:9·15灾害非人类活动的影响,属自然地质灾害,造成事故的主要原因为超高位岩体崩塌,而滚石的范围又超过前期预测的危险区.通过现场痕迹...