Mineralbestand und Genese fränkischer Keuper- und Lias-Tone

The clay mineral composition of Keuper and Liassic clays and marls from Franconia (southern Germany) varies in a characteristic manner within the stratigraphic profile:

1. 1.
   Considerable amounts of montmorillonite are characteristic of the Upper Burgsandstein (higher part of Middle Keuper), and comparable amounts of illite-montmorillonite mixed-layers characterize the Feuerletten (top of Middle Keuper). In addition to these minerals, both units contain much illite and muscovite, some kaolinite and quartz, feldspars and carbonates. According to geologic investigations, both sediments are of terrestrial origin (semi-arid climatic conditions).     
   
   

Tonminerale in normalsedimenten,hydrothermal beeinflu\ten sedimenten und Erzschlämmen des Roten Meeres

From 14 deeps and other regions of the Red Sea totally 226 samples from 28 cores recovered during the VALDIVIA cruises (1971, 1972) were investigated according to their clay mineral content (<2μm resp. < 6.3 μm) after carbonate dissolution. Three facies groups are to distinguish:

1. normal sediments: dominance of chlorite, kaolinite, illite, small amounts of smectite and sepiolite. Two palygorskite types are present only in a few samples.
2. normal sediments with hydrothermal influence: clay mineral paragenesis similar like that of normal sediments; but increase of smectite and presence of goethite in each sample; partly small contents of talc.
3. heavy metal deposits: dominance of iron-bearing smectite, partly with amorphous components resp. pure ore mineral assemblages with authigenic silicates (talc, quartz, opal, chrysotile, sepiolite, palygorskite, chlorite).

Crystallinity of the clay and ore minerals is independent from sedimentary overburden. Sepiolite shows in small amounts a wide distribution; palygorskite₂ (d₁₁₀=11.3 Å) yields locally an increased concentration in the range of pteropod layers cemented by aragonite. The environment of ore deposits is characterized by iron-bearing smectite besides the ore minerals.     

Response scenarios for the deltaic plain of the Rhône in the face of an acceleration in the rate of sea-level rise with special attention to<Emphasis Type="Italic">Salicornia</Emphasis>-type environments

One of the most critical problems facing many deltaic wetlands is a high rate of relative sea-level rise due to a combination of eustatic sea-level rise and local subsidence. Within the Rhône delta, the main source of mineral input to soil formation is from the river, due to the low tidal range and the presence of a continuous sea wall. We carried out field and modeling studies to assess the present environmental status and future conditions of the more stressed sites, i.e.,Salicornia-type marshes with a shallow, hypersaline groundwater. The impacts of management practices are considered by comparing impounded areas with riverine areas connected to the Rhône River. Analysis of vegetation transects showed differences between mean soil elevation ofArthrocnemum fruticosum (+31.2 cm),Arthrocnemum glaucum (+26.5 cm), bare soil (+16.2 cm), and permanently flooded soil (?12.4 cm). Aboveground and belowground production showed that root:shoot ratio forA. fruticosum andA. glaucum was 2.9 and 1.1, respectively, indicating more stressful environmental conditions forA. glaucum with a higher soil salinity and lack of soil drainage. The annual leaf litter production rate of the two species is 30 times higher than annual stem litter production, but with a higher long-term decomposition rate associated with leaves. We developed a wetland elevation model designed to predict the effect of increasing rates of sea-level rise on wetland elevation andSalicornia production. The model takes into account feedback mechanisms between soil elevation and river mineral input, and primary production. In marshes still connected to the river, mineral input decreased quickly when elevation was over 21 cm. Under current sea-level rise conditions, the annual amount of riverine mineral input needed to maintain the elevation of the study marshes is between 3,000 and 5,000 g m^?2 yr^?1. Simulations showed that under the Intergovernmental Panel on Climate Change best estimate sea-level rise scenario, a mineral input of 6,040 g m^?2 yr^?1 is needed to maintain marsh elevation. The medium term response capacity of the Rhône deltaic plain with rising sea level depends mainly on the possibility of supplying sediment from the river to the delta, even though the Rhône Delta front is wave dominated. Within coastal impounded marshes, isolated from the river, the sediment supply is very low (10 to 50 g m^?2 yr^?1), and an increase of sea-level rise would increase the flooding duration and dramatically reduce vegetation biomass. New wetland management options involving river input are discussed for a long-term sustainability of low coastal Mediterranean wetlands.     

Analysis and mapping of geochemical anomalies using logratio-transformed stream sediment data with censored values

There is lack of research and documentation of actual (as opposed to theoretical) benefits (e.g., mineral deposit discovery) of developments in compositional data analysis and imputation of censored values to mineral exploration geochemistry. In the present study, analyses of logratio- and ln-transformed stream sediment geochemical data containing ca. 30% of samples with censored values of a pathfinder element for the mineral deposit-type of interest yielded the following findings. Exclusion of those samples supports interpretation of multi-element anomalies reflecting the presence of mineralization. However, the multi-element anomaly maps obtained by exclusion of those samples are barely better than the multi-element anomaly maps derived by inclusion of those samples after replacing the censored values with 1/2 of detection limit or with imputed values. Logratio (i.e., alr, clr, or ilr) transformation, compared to ln-transformation, of stream sediment geochemical data does not improve mapping of pathfinder element anomalies reflecting the presence of mineralization. However, stream sediment geochemical data, excluding or including censored values (replaced with 1/2 of detection limit or with imputed values), should be clr- or ilr-transformed to enhance recognition of anomalous multi-element associations reflecting the presence of mineralization. The anomaly maps of multi-element associations derived from ilr-transformed data are better, albeit slightly, than the anomaly maps of multi-element associations derived from clr-transformed data. In the present study, the main benefit of either clr- or ilr-transformation, compared to either ln- or alr-transformation, of stream sediment geochemical data is the enhancement of anomalous multi-element associations reflecting the presence of mineralization. This is an important benefit because variations in trace element concentrations in regional-scale stream sediment geochemical data are mostly due to lithology and other factors (or processes) unrelated to mineralization. Further investigations of various exploration geochemical data are needed to demonstrate and document the actual (as opposed to theoretical) benefits of developments in compositional data analysis and imputation of censored values to mineral exploration.     

Temperaturen und Drucke bei der regionalen Metamorphose: Prinzipielle und praktische Hinweise

The author's concept (1970, 1974) of evaluating metamorphic conditions is explained on the basis of most recent petrologic data. The major points treated are:

1. Instead of usual petrographic mapping, petrographic work in the field is aimed at specific “targets”, i.e., rock compositions. This is so because only specific rocks may give petrogenetically relevant information in the four metamorphic grades.
2. There are very many mineral reactions in metamorphism but only a few are petrogenetically significant. These are important to know, and they are graphically demonstrated. Any mineral assemblage that is formed by a significant mineral reaction must be verified as a paragenesis of mutually contacting minerals. Only such parageneses deserve to be mapped in the field as isograds or isoreactiongrads.
3. Crossing isograds or isoreactionsgrads provide data on temperature and pressure during metamorphism for that part of a metamorphic terrane where the crossing has been observed.
4. The sequence of isograds or isoreaction-grads may be a pressure indicator. Moreover, such a sequence provides geodynamic information whether a larger metamorphic area has been lifted up evenly or has been tilted while it was uplifted after metamorphism.

     

Vermiculite bio-barriers for Cu and Zn remediation: an eco-friendly approach for freshwater and sediments protection

The increase in heavy metal contamination in freshwater systems causes serious environmental problems in most industrialized countries, and the effort to find eco-friendly techniques for reducing water and sediment contamination is fundamental for environmental protection. Permeable barriers made of natural clays can be used as low-cost and eco-friendly materials for adsorbing heavy metals from water solution and thus reducing the sediment contamination. This study discusses the application of permeable barriers made of vermiculite clay for heavy metals remediation at the interface between water and sediments and investigates the possibility to increase their efficiency by loading the vermiculite surface with a microbial biofilm of Pseudomonas putida, which is well known to be a heavy metal accumulator. Some batch assays were performed to verify the uptake capacity of two systems and their adsorption kinetics, and the results indicated that the vermiculite bio-barrier system had a higher removal capacity than the vermiculite barrier (+34.4 and 22.8 % for Cu and Zn, respectively). Moreover, the presence of P. putida biofilm strongly contributed to fasten the kinetics of metals adsorption onto vermiculite sheets. In open-system conditions, the presence of a vermiculite barrier at the interface between water and sediment could reduce the sediment contamination up to 20 and 23 % for Cu and Zn, respectively, highlighting the efficiency of these eco-friendly materials for environmental applications. Nevertheless, the contribution of microbial biofilm in open-system setup should be optimized, and some important considerations about biofilm attachment in a continuous-flow system have been discussed.     

Palynology of Triassic–Jurassic boundary sections in northern Switzerland

A first palynostratigraphic scheme of Upper Triassic deposits in northern Switzerland was established based on spore-pollen associations and dinoflagellate cyst records from the upper part of the Upper Triassic Klettgau Formation and the lower part of the Lower Jurassic Staffelegg Formation. Drill cores from the Adlerberg region (Basel Tabular Jura) and from Weiach (northern part of Canton Zurich) as well as from an outcrop at the Chilchzimmersattel (Basel Folded Jura) were studied and five informal palynological associations are distinguished. These palynological associations correlate with palynological association of the Central European Epicontinental Basin and the Tethyan realm and provide a stratigraphic framework for the uppermost Triassic sediments in northern Switzerland. Throughout the uppermost Triassic to Jurassic palynological succession a remarkable prominence of Classopollis spp. is observed. Besides Classopollis spp. the three Rhaetian palynological associations A to C from the Upper Triassic Belchen Member include typical Rhaetian spore-pollen and dinoflagellate taxa (e.g., Rhaetipollis germanicus, Geopollis zwolinskae, Rhaetogonyaulax rhaetica, and Dapcodinium priscum). Association B differs from association A in a higher relative abundance of the sporomorph taxa Perinopollenites spp. and the consistent occurrence of Granuloperculatipollis rudis and Ricciisporites tuberculatus. Spore diversity is highest in the late Rhaetian palynological association C and includes Polypodiisporites polymicroforatus. A Rhaetian age for the Belchen Member is confirmed by palynological associations A–C, but there is no record of the latest Rhaetian and the earliest Jurassic. In contrast to the Rhaetian palynological associations the Early Jurassic associations W and D include Pinuspollenites spp., Trachysporites fuscus (in association W), and Ischyosporites variegatus. In the view of the end-Triassic mass extinction and contemporaneous environmental changes the described palynofloral succession represents the pre-extinction phase (associations A and B) including a distinct transgression, the extinction phase (association C) associated with a regression, and the post-extinction phase (association W).     

Determination of point of zero charge of PILCS with single and mixed oxide pillars prepared from Tunisian-smectite

Different pillared interlayer clays (PILCs) with single oxide pillars of Cr and Al and mixed oxide pillars of these metals have been prepared from a Tunisian purified smectite (Hp): Several Al/metal, OH/metal and metal/clay ratios were used in order to investigate the effect on the chemical and physical properties, specifically the point of zero charge of the synthesized pillared clays. These chromium pillared clays compounds at n meq (Nitrate) and at n meq (Chlorite) are noted pillared clay and pillared clays \(Hp(20,40,60)_{NO_3 } \) and Hp(20,40,60)_Cl. The structure of the pillared materials are studied by XRD and cationic exchange capacity, the textural property are investigated by the specific surface area S_BET. The acid-base chemistry “surface acidity” of these products was analysed by using acid-base potentiometric in order to determine the PZC of each sample. The resulting materials exhibited basal spacings in the range of 13.96–21.13 Å, with high surface areas (10.58–198 m² g^?1). Pillared clays prepared from Tunisian purified smectite showed an increase of basal spacings and surface areas. A relatively strong interaction between metal and aluminium in the pillars was observed. The samples are studied by acid-base potentiometric. This experimental method is used to determine the point of zero charge (PZC). The PZC values of the edge sites are 8.2 for Tunisian purified smectite and 6.8; 5.9; 5.19; 6.84; 5.86; 5.73; 6.78; 7.56 for the differents samples respectively: \(Hp(20,40,60meq)_{NO_3 } \) Hp(20,40,60meq)_Cl; Hp-Cr/Al; Hp-Al.     

Composition and origin of the clay cover on North Brazilian laterites

The Belterra Clay in Northern Brazil is a uniform, yellowish, unstratified kaolinitic clay with variable contents of gibbsite. It is generally 5–10 m thick and covers a lateritic weathering crust on remnants of a dissected table-land. Complete profiles with Belterra Clay, the underlying bauxite/laterite and saprolite/bed rock were sampled in three areas of the Amazon region. The chemical and mineralogical data show a distinct affinity between the Belterra Clay and the underlying layers above all with the saprolite. Variations in the composition of the underlaying layers are reflected by the Belterra Clay. Among the structural and textural features important for the discussion of the origin of the Belterra Clay are the sharp contact between the clay cover and the underlying laterite as well as conglomeritic/brecciate textures and occasional bedding structure in the upper part of the lateritic crust. The detailed analyses do not permit definite conclusions on the origin of the Belterra Clay. Three hypotheses ar discussed:

1. In-situ formation of the clay cover by weathering processes.
2. Clay deposition after lateral transport of saprolitic material coming from former elevations inside or outside the present laterite areas.
3. Vertical transport of the saprolitic material to the surface by termites. However, thicknesses up to 20 m of the Belterra Clay cannot be explained solely by this process.

The compositional relations of the Belterra Clay with the underlying layers are of practical relevance for geological mapping and for mineral exploration.     

Out-of-sequence thrusts and paleogeography of the Rhenodanubian Flysch Belt (Eastern Alps) revisited

The Oberstdorf nappe of the Western and the Laab nappe of the Eastern Rhenodanubian Flysch (ERF) were independently identified as out-of-sequence thrust units by facies studies (Mattern 1999) and zircon analyses (Trautwein et al. 2001a, b, c), respectively. A new look at both areas reveals mutual similarities and new evidence for the out-of-sequence concept. Paleocurrent and heavy mineral data make it possible to reconstruct the sediment influx directions. From the Barremian to the mid-Campanian, the western and eastern basin segments were fed with south-derived garnet and north-derived zircon/”ZTR” (i.e., zircon, tourmaline, and rutile). Because both out-of-sequence units are relatively rich in zircon/ZTR they must have occupied the northernmost basin position. In the Western Rhenodanubian Flysch segment, the Sigiswang nappe occupied the central and the Üntschen nappe the southernmost basin position. In the ERF segment the central basin is represented by the Greifenstein nappe and the southernmost basin by the Kahlenberg nappe. Both out-of-sequence units do not occur in the northernmost and tectonically lowest position in their respective nappe piles as they were thrust over the other nappes. The reconstructed basin positions of the thrust units are suggested by the observation of a gradient in heavy mineral content in the thrust units. This paleogeographic arrangement is least problematic and renders models with differently positioned thrust units, requiring debris-shedding intrabasinal ridges, as unnecessarily complicated. Instead, we suggest that gradual changes in heavy mineral composition existed in across-basin direction. Garnet may stem from the Central Gneiss Complex of the Tauern window and formerly exposed lateral equivalents, all representing the southern Mid-Penninic zone. We assign the Falknis/Tasna nappe and formerly exposed lateral equivalents to the northern Mid-Penninic zone which served as the zircon/ZTR source. Interpreting Ebbing’s (Ph.D. thesis, Freie Universität Berlin, pp 1-143, 2002; Fig. 6.10) density section, we suggest that Mid-Penninic crust exists beneath the Central Gneiss Complex. During the latest Cretaceous much garnet was also N-derived. This may reflect processes related to the consumption of the North Penninic basin.     

The “South-Italian City” — a cultural-genetic type of city

The “South-Italian city” is characterized at four different levels as an independent cultural-genetic city-type:

1. The characteristics arrangement of the functional areas and the residential areas of different social groups is represented in a model.
2. From the model, developments and changes in the arrangement of the functional areas can be identified which clearly deviate from those which are derived from the universal city model.
3. Some of the structural individuality can be directly explained by the peculiar features of the respective social and economic history.
4. Some of the special features must, however, be traced back to a wider historico-cultural background. Through this run processes which flow through the universal city development in similar forms, to the deviating structure of the “South-Italian city”.

     

Clay mineralogy of archaeological soil: an approach to paleoclimatic and environmental reconstruction of the archaeological sites of the Paharpur area,Badalgacchi upazila,Naogaon district,Bangladesh

A geo-archaeological examination was carried out in and around the Paharpur area, Badalgacchi upazila of Naogaon District in the north-western part of Bangladesh. Clay mineralogy and global paleo-temperature curves were used to determine the paleoclimatic and depositional environmental conditions of the Holocene archaeological soils (Barind clay residuum) of the Paharpur archaeological spot. Clay mineralogical data show that the dominant clay mineral is illite with subordinate amounts of kaolinite and chlorite. The high illite and low kaolinite content implies a marine or estuarine deposit. The clay mineral ratio log diagram, constructed by plotting the 7–10°Å integrated intensity ratios versus depth, supports this assumption. The presence of illite, together with quartz and feldspar, suggests high detrital input under generally cool to temperate and dry climates. Chlorite is another common by-product of weathering reactions with low hydrolysis, which is typical for cool to temperate and dry climates. The results suggest the existence of a marine–estuarine influence under a generally cool to temperate and dry climates around Paharpur and the surrounding region throughout the Pala dynasty around mid-century 700 a.d. to early 1100 a.d. Furthermore, this observation is consistent with the global paleo-temperature curves.     

Groundwater development,Kharga Oases,Western Desert of Egypt: A long-term environmental concern

The groundwater reserves in Kharga Oases have been studied for the long-term socioeconomic development in the area. The Nubian Sandstone, which consists of a thick sequence of coarse clastic sediments of sandstone, sandy clay interbedded with shale, and clay beds, forms a complex aquifer system. The Nubian Aquifer has been providing water to artesian wells and springs in the Kharga Oases for several thousand years. Groundwater in the Kharga Oases is withdrawn from springs and shallow and deep artesian wells Nearly all the wells originally flowed, but with the exploitation of ground-water from deep wells for irrigation beginning about 1959. the natural flows declined as more and more closely spaced deep wells were drilled By 1975 many deep wells had ceased to flow The water demand in the area has been met by pumping both shallow and deep wells The total annual extraction from deep wells has fluctuated over the year, however, the annual withdrawal from deep wells has exceeded extraction from shallow wells About 17 billion m³ of water was withdrawn from the combination of shallow and deep wells during the period 1960–1980 The Nubian complex aquifer in the Kharga Oases has a very large groundwater potential that could be exploited and beneficially used for a long-term agricultural development in the area, provided proper well spacing and management are implemented Other major environmental considerations for which precise hydrogeologic data are needed include

1. Determination of the long-term yield available from properly constructed and producing artesian wells that will support a planned migration of population from the overcrowded Nile delta and flood plain areas
2. Development of an effective management program and adequate staff to maintain groundwater production over an extended period of years
3. The impact on climate caused by extensive irrigation in the oases of the Western Desert of Egypt
4. Protection against water logging of soils from irrigation practices
5. Protection against salinization of soils from irrigation practices
6. Development of effective surface and subsurface drainage practices
7. The impact of farming and pest control practices on the shallow groundwater of the oases
8. Determination of the long-term development of the artesian water on the quality of the water from the aquiter systems in the Western Desert

This paper addresses items 1, 2 and 8.     

Petrographie des Praezechsteins der Bohrung „Dransfeld l”

Core samples from the “Praezechstein” formation of the bore “Dransfeld 1” were investigated by optical, X-ray, and chemical methods. The rock formation consists of graywackes interbedded with Slates. The graywackes contain mineral.components and rock fragments which are also common in the graywackes of Harz and “Rheinisches Schiefergebirge”, so that a common source of derivation may be concluded, namely the “Mitteldeutsche Schwelle”. The distinctive features of the Dransfeld-graywackes however as compared to those of Harz and “Rheinisches Schiefergebirge” are:

1. 1.
   A higher content of rock fragments specially of volcanic origin.     
   
   

Forest condition and forest damages — contribution of remote sensing to different inventory approaches

The development of inventory activities in the field of forest damage assessment and monitoring during the last decade in Germany and the present state are recorded as far as remote sensing has been involved. Any forest inventory is influenced by external factors, and the resulting difficulties for an introduction of new technologies are described. The following tasks and/or methods are discussed:

-global approaches to deforestation monitoring

-working experience from local and regional case studies

-vegetation and vegetation-damage monitoring in ”urban forestry”

-sampling approaches for large areas

-the contribution of spectral signatures and satellite remote sensing to damage assessment

     

Correlation analyses of effects of temperature on physical and mechanical properties of clay

In determining the physical and mechanical parameters of clay, it is sometimes necessary to determine them indirectly from other parameters since they cannot be measured directly from laboratory or field tests. In order to determine the effect of temperature on the behavior of clay, an indirect approach is used here by analyzing the changes of mass (\(\Delta m\)), density (\(\rho\)), porosity (\(\phi\)), P-wave velocity (\({v_p}\)), thermal conductivity (\(\lambda\)), specific heat capacity (c), resistivity (R) and uniaxial compressive strength (f) of clay from eastern China for a temperature range between 20 and 800 °C. The results indicate that temperature has a significant effect on these parameters. Comparisons between \(\Delta m\) and \(\rho\), \(\Delta m\) and \({v_p}\), \(\rho\) and \({v_p}\), \(\phi\) and \(\lambda\), \({v_p}\) and f, R and f show a linear change among these parameters,whereas the relationships among \(\Delta m\) and \(\phi\), \(\phi\) and \({v_p}\), \(\phi\) and R, \({v_p}\) and \(\lambda\), \(\phi\) and f are exponential. It is difficult to obtain these relationships by using regression analysis with high levels of accuracy. Further refinement is therefore required.     

Chlorit-Hornblende-Felse des Bergsträßer Odenwaldes und ihre Phasenpetrologie

Ultrabasic metamorphic rocks with typical mineral assemblage of cummingtonitic hornblende+Mg-chlorite+talc (described byMatthes u.Okrusch, 1965, and called “hösbachit”) were found for the first time in Odenwald/Germany. Three steps of metamorphic development can be described: the primary magmatic ultrabasic rock consisted of (1) orthopyroxene (bronzite), clinopyroxene (diallage), poikilitic olivine, and some hornblende. This is indicated by textural relicts, structural and geochemical investigations. A regional metamorphic process under conditions of the staurolite-almandine-subfacies ofWinkler’s andTurner andVerhoogen’s almandine-amphibolite facies transformed this assemblage to (2): cummingtonitic hornblende I+Mg-chlorite I (clinochlore)+talc. The third step followed under more diaphthoritic conditions and brought mineral assemblage (3): tremolitic hornblende II+Mg-chlorite II (pennine)+talc.