Length Scales of Scalar Diffusion in the Convective Boundary Layer: Laboratory Observations

A laboratory study of scalar diffusion in the convective boundary layer has found results that are consistent with a 1999 large-eddy simulation (LES) study by Jonker, Duynkerke and Cuijpers. For bottom-up and top-down scalars (introduced as ‘infinite’ area sources of passive tracer at the surface and inversion, respectively) the dominant length scale was found to be much larger than the length scale for density fluctuations, the latter being equal to the boundary-layer depth h. The variance of the normalized passive scalar grew continuously with time and its magnitude was about 3–5 times larger for the top-down case than for the bottom-up case. The vertical profiles of the normalized passive scalar variance were found to be approximately constant through the convective boundary layer (CBL) with a value of about 3–8c_*² for bottom-up and 10–50c_*² for top-down diffusion. Finally, there was some evidence of a minimum in the variance and dominant length scale for scalar flux ratios (top-down to bottom-up flux) close to −0.5. All these convection tank results confirm the LES results and support the hypothesis that there is a distinct difference in behaviour between the dynamic and passive variables in the CBL.     

Similarity scaling applied to sodar observations of the convective boundary layer above an irregular hill

Nine profiles of the temperature structure parameter C _T ² and the standard deviation of vertical velocity fluctuations ( _w) in the convective boundary layer (CBL) were obtained with a monostatic Doppler sodar during the second intensive field campaign of the First ISLSCP Field Experiment in 1987. The results were analyzed by using local similarity theory. Local similarity curves depend on four parameters: the height of the mixed layer (z _i ), the depth of the interfacial layer (), and the temperature fluxes at the top of the mixed layer (Q _i ) and the surface (Q _o). Values of these parameters were inferred from sodar data by using the similarity curve for C _T ² and observations at three points in its profile. The effects of entrainment processes on the profiles of C _T ² and _wnear the top of the CBL appeared to be described well by local similarity theory. Inferred estimates of surface temperature flux, however, were underestimated in comparison to fluxes measured by eddy correlation. The measured values of _wappeared to be slightly smaller than estimates based on available parmeterizations. These discrepancies might have been caused by experimental error or, more likely, by the distortion of turbulence structure above the site by flow over the nonuniform terrain at the observation site.     

Vertical velocity field in the convective boundary layer as observed with an acoustic Doppler sodar

The morning development of the daytime convective boundary layer (CBL) during fine weather has been observed with an acoustic Doppler sodar of the C.R.P.E. In particular, the vertical profile of the vertical velocity third-order statistic W* ³ has been obtained. This quantity is a maximum near 0.3z _I where z _I, is the height of the CBL. The histogram of vertical velocity in the CBL shows a relationship between W ³ and the convective velocity W _* and is useful for convective plume determination.     

The Role of Shear in the Morning Transition Boundary Layer

We use large-eddy simulation (LES) to better define the early stages of the morning transition boundary layer. Previous LES studies relating to the morning transition boundary layer focus on the role of the entraining convective boundary layer (CBL). By using a combination of different domain sizes and grid lengths, the full evolution from the stable boundary layer (SBL) to the CBL is modelled here. In the early stages of the morning transition the boundary layer is shown to be a combination of a shallow mixed layer capped by a significant shear driven stable boundary layer (the so-called mixed CBL–SBL state). The mixed CBL–SBL state is the key to understanding the sensitivity to shear. Turbulent kinetic energy budgets also indicate that it is shear driven. The negative flux from the mixed CBL–SBL state extends much further above the minimum than is typically found for the CBL later in the day, and the depth of penetration scales as w _m /N _i , where w _m is the combined friction and convective velocity scale and N _i the static stability at the inversion top.     

论边界层中的大气扩散PDF模式

基于大气扩散Ｋ理论，用作为风速脉动均方差和拉氏时间尺度函数的湍流交换系数，得到了直接利用风速脉动几率密度而不用扩散参数的大气扩散ＰＤＦ模式。分别研究了对流边界层上升气流区与下降区垂直速度的统计特征，求得双正态ＰＤＦ模式。在给定ＣＢＬ自身参数如对流特征速度ｗ＊，顶高ｈｉ和源高度上的平均风速时，该模式计算出的无量纲浓度分布与室内外测试结果一致。     

Coherence and Scale of Vertical Velocity in the Convective Boundary Layer from a Doppler Lidar

We utilized a Doppler lidar to measure integral scale and coherence of vertical velocity w in the daytime convective boundary layer (CBL). The high resolution 2 μm wavelength Doppler lidar developed by the NOAA Environmental Technology Laboratory was used to detect the mean radial velocity of aerosol particles. It operated continuously in the zenith-pointing mode for several days in the summer 1996 during the “Lidars in Flat Terrain” experiment over level farmland in central Illinois. We calculated profiles of w integral scales in both the alongwind and vertical directions from about 390 m height to the CBL top. In the middle of the mixed layer we found, from the ratio of the w integral scale in the vertical to that in the horizontal direction, that the w eddies are squashed by a factor of about 0.65 as compared to what would be the case for isotropic turbulence. Furthermore, there is a significant decrease of the vertical integral scale with height. The integral scale profiles and vertical coherence show that vertical velocity fluctuations in the CBL have a predictable anisotropic structure. We found no significant tilt of the thermal structures with height in the middle part of the CBL.The National Center for Atmospheric Research is sponsored by the National Science Foundation.     

Turbulence Characteristics of the Shear-Free Convective Boundary Layer Driven by Heterogeneous Surface Heating

Large-eddy simulations (LESs) are employed to investigate the turbulence characteristics in the shear-free convective boundary layer (CBL) driven by heterogeneous surface heating. The patterns of surface heating are arranged as a chessboard with two different surface heat fluxes in the neighbouring patches, and the heterogeneity scale Λ in four different cases is taken as 1.2, 2.5, 5.0 and 10.0 km, respectively. The results are compared with those for the homogeneous case. The impact of the heterogeneity scale on the domain-averaged CBL characteristics, such as the profiles of the potential temperature and the heat flux, is not significant. However, different turbulence characteristics are induced by different heterogeneous surface heating. The greatest turbulent kinetic energy (TKE) is produced in the case with the largest heterogeneity scale, whilst the TKE in the other heterogeneous cases is close to that for the homogeneous case. This result indicates that the TKE is not enhanced unless the scale of the heterogeneous surface heating is large enough. The potential temperature variance is enhanced more significantly by a larger surface heterogeneity scale. But this effect diminishes with increasing CBL height, which implies that the turbulent eddy structures are changed during the CBL development. Analyses show that there are two types of organized turbulent eddies: one relates to the thermal circulations induced by the heterogeneous surface heating, whilst the other identifies with the inherent turbulent eddies (large eddies) induced by the free convection. At the early stage of the CBL development, the dominant scale of the organized turbulent eddies is controlled by the scale of the surface heterogeneity. With time increasing, the original pattern breaks up, and the vertical velocity eventually displays horizontal structures similar to those for the homogeneous heating case. It is found that after this transition, the values of λ/z _i (λ is the dominant horizontal scale of the turbulent eddies, z _i is the boundary-layer height) ≈1.6, which is just the aspect ratio of large eddies in the CBL.     

Parameterization of sheared entrainment in a well-developed CBL. Part I: Evaluation of the scheme through large-eddy simulations

The entrainment flux ratio A _e and the inversion layer (IL) thickness are two key parameters in a mixed layer model. A _e is defined as the ratio of the entrainment heat flux at the mixed layer top to the surface heat flux. The IL is the layer between the mixed layer and the free atmosphere. In this study, a parameterization of A _e is derived from the TKE budget in the firstorder model for a well-developed CBL under the condition of linearly sheared geostrophic velocity with a zero value at the surface. It is also appropriate for a CBL under the condition of geostrophic velocity remaining constant with height. LESs are conducted under the above two conditions to determine the coefficients in the parameterization scheme. Results suggest that about 43% of the shear-produced TKE in the IL is available for entrainment, while the shear-produced TKE in the mixed layer and surface layer have little effect on entrainment. Based on this scheme, a new scale of convective turbulence velocity is proposed and applied to parameterize the IL thickness. The LES outputs for the CBLs under the condition of linearly sheared geostrophic velocity with a non-zero surface value are used to verify the performance of the parameterization scheme. It is found that the parameterized A _e and IL thickness agree well with the LES outputs.     

基于风廓线仪的华南地区夏季边界层湍流统计特征研究

采用双权重算法,使用2015年6—8月我国东南部业务风廓线雷达资料,通过湍流脉动垂直速度方差和偏度的计算和分析,对晴空和低云主导情况下的边界层湍流特征以及中小尺度局地环流对于边界层湍流的影响进行研究。主要结论如下:(1)晴天情况下垂直速度标准差和垂直速度偏度都具有明显的日变化特征,湍流主要由下垫面加热驱动发展;(2)在低云主导情况下,湍流明显弱于晴天对流边界层的湍流强度,边界层内湍流的发展不仅受地面加热的影响,而且在边界层上部存在明显的自上而下发展的湍流,这主要是由于边界层顶云辐射冷却造成的;(3)除了上述两种情况,边界层湍流发展同时受到局地中小尺度环流或者天气系统的影响,因而呈现出更多的复杂性。      

Airborne measurements of turbulent trace gas fluxes and analysis of eddy structure in the convective boundary layer over complex terrain

Using the new high-frequency measurement equipment of the research aircraft DO 128, which is described in detail, turbulent vertical fluxes of ozone and nitric oxide have been calculated from data sampled during the ESCOMPTE program in the south of France. Based on airborne turbulence measurements, radiosonde data and surface energy balance measurements, the convective boundary layer (CBL) is examined under two different aspects. The analysis covers boundary-layer convection with respect to (i) the control of CBL depth by surface heating and synoptic scale influences, and (ii) the structure of convective plumes and their vertical transport of ozone and nitric oxides. The orographic structure of the terrain causes significant differences between planetary boundary layer (PBL) heights, which are found to exceed those of terrain height variations on average. A comparison of boundary-layer flux profiles as well as mean quantities over flat and complex terrain and also under different pollution situations and weather conditions shows relationships between vertical gradients and corresponding turbulent fluxes. Generally, NO_x transports are directed upward independent of the terrain, since primary emission sources are located near the ground. For ozone, negative fluxes are common in the lower CBL in accordance with the deposition of O₃ at the surface.The detailed structure of thermals, which largely carry out vertical transports in the boundary layer, are examined with a conditional sampling technique. Updrafts mostly contain warm, moist and NO_x loaded air, while the ozone transport by thermals alternates with the background ozone gradient. Evidence for handover processes of trace gases to the free atmosphere can be found in the case of existing gradients across the boundary-layer top. An analysis of the size of eddies suggests the possibility of some influence of the heterogeneous terrain in mountainous area on the length scales of eddies.     

Temporal Oscillations in the Convective Boundary Layer Forced by Mesoscale Surface Heat-Flux Variations

A theoretical approach suggests that the surface heterogeneity on a scale of tens of kilometres can generate mesoscale motions that are not in a quasi-stationary state. The starting point of the theoretical approach is the equations of horizontal velocity and potential temperature that are low-pass filtered with a mesoscale cut-off wavelength. The transition of the generated mesoscale motions from a quasi-stationary state to a non-stationary state occurs when horizontal advection is strong enough to level out the potential temperature gradient on the surface heterogeneity scale. Large-eddy simulations (LES) suggest that the convective boundary layer (CBL) changes to a non-stationary state when forced by a surface heat-flux variation of amplitude of 100W m⁻² or higher and a wavelength of the order of 10 km. Spectral analysis of the LES reveals that when the mesoscale motions are in a quasi-stationary state, the energy provided by the surface heat-flux variation remains in organized mesoscale motions on the scale of the surface variation itself. However, in a non-stationary state, the energy cascades to smaller scales, with the cascade extending down into the turbulence scale when the wavelength of the surface heat-flux variation is on a scale smaller than 100 times the CBL height. The energy transfer from the generated mesoscale motions to the CBL turbulence results in the absence of a spectral gap between the two scales. The absence of an obvious spectral gap between the generated mesoscale motions and the turbulence raises questions about the applicability of mesoscale models for studies on the effect of high-amplitude surface heterogeneity on a scale of tens of kilometres. The National Center for Atmospheric Research is sponsored by the National Science Foundation.     

The impact of soil moisture on dispersion-related characteristics

This study investigates the impact of soil moisture availability on dispersion-related characteristics: surface fric-tion velocity (u*), characteristic scales of temperature and humidity (T* and q*), the planetary boundary layer height (h) and atmospheric stability classified by Monin-Obukhov length (L), Kazanski-Monin parameter (μ) and convective velocity scale (w*) during daytime convective condition using a one-dimensional primitive equation with a refined soil model.     

Verifying Inventory Predictions of Animal Methane Emissions with Meteorological Measurements

The paper examines the strengths and weaknesses of a rangeof meteorological flux measurement techniques that mightbe used to verify predictions of greenhouse gas inventories.Recent research into emissions of methane (CH₄)produced by enteric fermentation in grazing cattle and sheepis used to illustrate various methodologies. Quantifying thisimportant source presents special difficulties because the animalsconstitute moving, heterogeneously distributed, intermittent, pointsources. There are two general approaches: one, from the bottom up,involves direct measurements of emissions from a known number ofanimals, and the other, from the top down, infers areal emissions ofCH₄ from its atmospheric signature. A mass-balance methodproved successful for bottom-up verification. It permits undisturbedgrazing, has a simple theoretical basis and is appropriate for fluxmeasurements on small plots and where there are scattered pointsources. The top-down methodologies include conventional flux-gradientapproaches and convective and nocturnal boundary-layer (CBL and NBL)budgeting schemes. Particular attention is given to CBL budget methods inboth differential and integral form. All top-down methodologies require ideal weather conditions for their application, and they suffer from the scattered nature of the source, varying wind directions and low instrument resolution. As for mass-balance, flux-gradient micrometeorological measurements were in good agreement with inventory predictions of CH₄ production by livestock, but the standard errors associated with both methods were too large to permit detection of changes of a few per cent in emission rate, which might be important for inventory, regulatory or research purposes. Fluxes calculated by CBL and NBL methods were of the same order of magnitude as inventory predictions, but more improvement is needed before their use can be endorsed. Opportunities for improving the precision of both bottom-up and top-down methodologies are discussed.     

Observation of lake breeze penetration and subsequent development of the thermal internal boundary layer for the Nanticoke II Shoreline Diffusion Experiment

The turbulent structure of the lake breeze penetration and subsequent development of the thermal internal boundary layer (TIBL) was observed using a kytoon-mounted ultrasonic anemometer-thermometer. The lake breeze penetrated with an upward rolling motion associated with the upward flow near the lake breeze front. After the lake breeze front passed, the behaviors of the velocity and temperature at the top of the lake breeze layer were similar to those found in convective boundary layers (CBL). Comparing _gq/_*, _u /w _* and _w /w _* between the present observation of TIBL development after the passage of the lake breeze front and CBL data from the literature, the /_* values showed reasonable agreement; however, _u /w _* and _w /W_* had smaller values in the TIBL than in the CBL at higher altitudes. This is due to the differences in the mean velocity profiles. While the CBL has a uniform velocity profile, the TIBL has a peak at lower elevation due to the lake breeze penetration; the velocity then decreases with height.Present address: The Institute of Behavioral Science, 1-35-7 Yoyogi, Tokyo 151, Japan.     

Airflow over a mountain and the convective boundary layer

In this paper, the analytical model coupling the convective boundary layer (CBL) with the free atmosphere developed by Qi and Fu (1992) is improved. And by this improved model, the interaction between airflow over a mountain and the CBL is further discussed. The conclusions demonstrate: (1) The perturbation potential temperatures in the free atmosphere can counteract the effect of orographic thermal forcing through entraining and mixing in the CBL. If _M > _F , the feedback of the perturbation potential temperatures in the free atmosphere is more important than orographic thermal forcing, which promotes the effect of interfacial waves. If _M < _F , orographic thermal forcing is more important, which makes the interfacial height and the topographic height identical in phase, and the horizontal speeds are a maximum at the top of the mountain. (2) The internal gravity waves propagating vertically in the free atmosphere cause a strong downslope wind to become established above the lee slope in the CBL and result in the hydraulic jump at the top of the CBL. (3) With the CBL deepening, the interfacial gravity waves induced by the potential temperature jump at the top of the CBL cause the airflow in the CBL to be subcritical.     

On the Nature of the Transition Between Roll and Cellular Organization in the Convective Boundary Layer

Both observational and numerical studies of the convective boundary layer (CBL) have demonstrated that when surface heat fluxes are small and mean wind shear is strong, convective updrafts tend to organize into horizontal rolls aligned within 10–20\(^\circ \) of the geostrophic wind direction. However, under large surface heat fluxes and weak to negligible shear, convection tends to organize into open cells, similar to turbulent Rayleigh-Bénard convection. Using a suite of 14 large-eddy simulations (LES) spanning a range of \(-z_i/L\) between zero (neutral) and 1041 (highly convective), where \(z_i\) is the CBL depth and L is the Obukhov length, the transition between roll- and cellular-type convection is investigated systematically for the first time using LES. Mean vertical profiles including velocity variances and turbulent transport efficiencies, as well the “roll factor,” which characterizes the rotational symmetry of the vertical velocity field, indicate the transition occurs gradually over a range of \(-z_i/L\); however, the most significant changes in vertical profiles and CBL organization occur from near-neutral conditions up to about \(-z_i/L \approx \) 15–20. Turbulent transport efficiencies and quadrant analysis are used to characterize the turbulent transport of momentum and heat with increasing \(-z_i/L\). It is found that turbulence transports heat efficiently from weakly to highly convective conditions; however, turbulent momentum transport becomes increasingly inefficient as \(-z_i/L\) increases.     

一个对流边界层中的随机扩散模式

通过对对流边界层(CBL)湍流结构的分析,首次提出用两种不同尺度的湍流模拟CBL中的铅直扩散.在此基础上发展了一个随机扩散模式,并用它模拟了典型对流条件下两种高架连续点源的扩散.与Willis水槽模拟和Lamb等人数值模拟以及CONDORS计划外场试验的结果的比较表明,本模式能成功地模拟CBL中的横向积分浓度.与其它数值模式相比,还具有输入参数少、计算量极小和更加简单实用的优点.     

Scaling Properties of Temperature Spectra and Heat-Flux Cospectra in the Surface Friction Layer Beneath an Unstable Outer Layer

Temperature variance and temperature power spectra in the unstable surface layer have always presented a problem to the standard Monin-Obukhov similarity model. Recently that problem has intensified with the demonstration by Smedman et al. (2007, Q J Roy Meteorol Soc 133: 37–51) that temperature spectra and heat-flux cospectra can have two distinct peaks in slightly unstable conditions, and by McNaughton et al. (2007, Nonlinear Process Geophys 14: 257–271) who showed that the wavenumber of the peak of temperature spectra in a convective boundary layer (CBL), closely above the surface friction layer (SFL), can be sensitive to the CBL depth, z _i. Neither the two-peak form at slight instability nor the dependence of peak position on z _i at large instability is compatible with the Monin-Obukhov model. Here we examine the properties of temperature spectra and heat-flux cospectra from between these extremes, i.e. from within the unstable SFL, in two experiments. The analysis is based on McNaughton’s model of the turbulence structure in the SFL. According to this model, heat is transported through most of the SFL by sheet plumes, created by the action of impinging outer eddies. The smallest and most effective of these outer eddies have sizes that scale on SFL depth, z _s. The z _s-scale eddies and plumes are organised within the overall convection pattern in the CBL, and in turn they organise the motion of smaller eddies within the SFL, whose sizes scale on height, z. The main experimental results are: (1) the peak amplitudes of the temperature spectra in the SFL are collapsed with a scaling factor (z_sz)^1/3e_o^2/3{(z_{\rm s}z)^{1/3}\varepsilon_{\rm o}^{2/3}} divided by the square of the surface temperature flux, where e_o{\varepsilon_{\rm o}} is the dissipation rate of turbulent energy in the outer CBL (above the SFL); (2) the peak wavenumbers of the temperature spectra are collapsed with the mixed length scale (z _i z _s)^1/2; (3) the peak wavenumbers of the heat-flux cospectra are collapsed with the doubly-mixed length scale (z _i z _s)^1/4 z ^1/2; (4) for z/z _s < 0.03, the peak in the cospectrum is replaced by another peak at a wavenumber about a magnitude larger. This peak’s position scales on z; (5) all these findings are consistent with the observations of Smedman et al.     

Parameterization of Sheared Convective Entrainment in the First-Order Jump Model: Evaluation Through Large-Eddy Simulation

In this note, two different approaches are used to estimate the entrainment-flux to surface-flux ratio for a sheared convective boundary layer (CBL); both are derived under the framework of the first-order jump model (FOM). That suggested by Sun and Wang (SW approach) has the advantage that there is no empirical constant included, though the dynamics are described in an implicit manner. The second, which was proposed by Kim et al. and Pino et al. (KP approach), explicitly characterizes the dynamics of the sheared entrainment, but uncertainties are induced through the empirical constants. Their performances in parameterizing the CBL growth rate are compared and discussed, and a new value of the parameter A ₃ in the KP approach is suggested. Large-eddy simulation (LES) data are employed to test both approaches: simulations are conducted for the CBL growing under varying conditions of surface roughness, free-atmospheric stratification, and wind shear, and data used when the turbulence is in steady state. The predicted entrainment rates in each case are tested against the LES data. The results show that the SW approach describes the evolution of the sheared CBL quite well, and the KP approach also reproduces the growth of the CBL reasonably, so long as the value of A ₃ is modified to 0.6.     

A note on the top-down and bottom-up gradient functions over a forested site

The dimensionless bottom-up and top-down gradient functions in the convective boundary layer (CBL) are evaluated utilizing long-term well-calibrated carbon dioxide mixing ratio and flux measurements from multiple levels of a 447-m tall tower over a forested area in northern Wisconsin, USA. The estimated bottom-up and top-down functions are qualitatively consistent with those from large-eddy simulation (LES) results and theoretical expectations. Newly fitted gradient functions are proposed based on observations for this forested site. The integrated bottom-up function over the lowest 4% of the CBL depth estimated from the tower data is about five times larger than that from LES results for a ‘with-canopy’ case, and is smaller than that from LES results for a ‘no-canopy’ case by a factor of 0.7. We discuss the uncertainty in the evaluated gradient functions due to stability, wind direction, and uncertainty in the entrainment flux and show that while all of these have a significant impact on the gradient functions, none can explain the differences between the modelled and observed functions. The effects of canopy features and atmospheric stability may need to be considered in the gradient function relations.