Joint isotopic mass balance: a novel approach to quantifying channel bed to channel margins sediment transfer during storm events

The important role of floodplains and the broader riparian zone in providing temporary storage for a large fraction of the annual sediment load of rivers is well established, but this understanding is largely based on observations of the long‐term average behavior of the catchment. Here we combine measurements of the fallout radionuclides ⁷Be and ²¹⁰Pb and the stable isotopes of hydrogen in water to quantify fine sediment mobilization and storage in a stream and its channel margins during individual intermediate‐sized storm events with recurrence intervals of a few months or less. We demonstrate this method using five storm events in a small (~15 km²), undeveloped, gravel‐bedded tributary of the Connecticut River (USA). We estimate that in each storm, the mass of sediment deposited onto the margins accounts for almost 90% of the sediment mobilized from the bed, with the remainder of the mobilized bed sediment transported downstream as suspended load. The result that the bed is a net source of sediment to the stream and the margins a net sink is robust, but estimates of the mass of material eroded from the bed and deposited on the margins are less certain. The source of sediment to the bed remains unclear as, consistent with earlier studies, we observe only limited deposition of sediment to the bed during the storm events. The suspended sediment is organic‐rich and thus its source may be associated with in‐channel organic decay between storm events. Understanding the coupled interactions between discharge magnitude and frequency and sediment resupply at the event time scale has important implications for stream restoration efforts seeking to connect the channel and the broader riparian zone, and for the development of accurate sediment budgets and predictions of sediment flux from a watershed. Copyright © 2015 John Wiley & Sons, Ltd.     

Using radiometric fingerprinting and phosphorus to elucidate sediment transport dynamics in an agricultural watershed

The major goals of this study were to determine stream bed sediment erosion/deposition rates, sediment age, percent ‘new’ sediment, and suspended sediment origin during two storm events of contrasting magnitudes (11.9 mm over 5 h and 58.9 mm over 39 h) using fallout radionuclides (excess lead 210 – ²¹⁰Pb_xs and beryllium 7 – ⁷Be) and link the nature and type of sediment source contributions to potential phosphorus (P) off‐site transport. The study was conducted in cropland‐dominated and mixed land use subwatersheds in the non‐glaciated Pleasant Valley watershed (50 km²) in South Central Wisconsin. Fine sediment deposition and erosion rates on stream beds varied from 0.76 to 119.29 mg cm^?2 day^?1 (at sites near the watershed outlet) and 1.72 to 7.72 mg cm^?2 day^?1 (at sites in the headwaters), respectively, during the two storm events. The suspended sediment age ranged from 123 ± 12 to 234 ± 33 days during the smaller storm event; however, older sediment was more prevalent (p = 0.037) in the streams during the larger event with suspended sediment age ranging from 226 ± 9 to 322 ± 114 days. During the small and large storm event, percent new sediment in suspended sediment ranged from 5.3 ± 2.1 to 21.0 ± 2.9% and 5.3 ± 2.7 to 6.7 ± 5.7%, respectively. In the cropland‐dominated subwatershed, upland soils were the major source of suspended sediment, whereas in the mixed land use subwatershed, both uplands and stream banks had relatively similar contributions to suspended sediment. In‐stream (suspended and bed) sediment P levels ranged from 703 ± 193 to 963 ± 84 mg kg^?1 during the two storm events. The P concentrations in suspended and bed sediment were reflective of the dominant sediment source (upland or stream bank or mixed). Overall, sediment transport dynamics showed significant variability between subwatersheds of different land use characteristics during two contrasting storm events. Copyright © 2014 John Wiley & Sons, Ltd.     

Estimation of suspended sediment sources using 137Cs and 210Pbex in unmanaged Japanese cypress plantation watersheds in southern Japan

To analyse suspended sediment sources in unmanaged Japanese cypress plantation watersheds, field measurements and fingerprinting of the suspended sediment was conducted in the Shimanto River basin in southern Japan. For sediment fingerprinting, ¹³⁷Cs and ²¹⁰Pb_ex were detected by means of gamma‐ray spectrometry in the surface soil of the forest floor, stream bank and truck trail and mobilized sediment by interrill erosion. The ¹³⁷Cs and ²¹⁰Pb_ex activities associated with the forest floor materials were considerably higher than those of the stream bank and truck trail. The ¹³⁷Cs and ²¹⁰Pb_ex activities associated with the suspended sediment were found to vary with the sampling period. Evidently, the suspended sediment can comprise materials generated from the forest floor by interrill erosion and those from the truck trail and/or stream bank. The multivariate sediment‐mixing model using ¹³⁷Cs and ²¹⁰Pb_ex showed that the contribution of the forest floor varied periodically, ranging from 23–56% in the Hinoki 156 subwatershed and from 18–85% in the Hinoki 155 subwatershed. The difference in the average contribution of the forest floor between Hinoki 156 (46%) and Hinoki 155 (69%) may relate to the presence of truck trail networks in the watershed. The truck trail network can play roles of sediment source and pathway for sediment from forest floor to stream channel due to the concentrated overland flow on the truck trail during heavy rainfall events. These results indicate that the forest floor should be recognized as a major source of suspended sediment in unmanaged Japanese cypress plantation watersheds. Copyright © 2008 John Wiley & Sons, Ltd.     

Sediment yields and sources in a welsh upland lake-catchment during the past 800 years

Estimates of suspended sediment yield over the past 800 years have been derived from a whole-basin study of lake sediments in Llyn Geirionydd, North Wales. Magnetic and physical sediment properties were used to correlate a suite of cores to a master chronology based on ²¹⁰Pb and ¹⁴C dates. The sources of sediment within the catchment were identified by comparing the magnetic and heavy metal properties of sediments, soils, and stream sediments. Mean suspended sediment yields range from 6 to 18 t km^?2 yr^?1 with high yields in the periods 1765-1830 and 1903-1985 corresponding to mining activities in the catchment. The impact of earlier deforestation, agricultural expansion, or climatic change on sediment yields is low, although there is evidence that agricultural activities increased levels of peak stream discharge. Afforestation in the 20th century does not appear to have significantly increased sediment yield. Sediment sources have remained fairly constant through time; they appear to be widespread and dominated by stream channel sides rather than point sources, except during the mining phases when spoil material has dominated the sediment load. Sediment loads to the lake today are still dominated by sediment derived from unvegetated spoil heaps.     

Quantification of sediment source contributions in two paired catchments of the Brazilian Pampa using conventional and alternative fingerprinting approaches

The knowledge of the contribution of sediment sources to river networks is a prerequisite to understand the impact of land use change on sediment yield. We calculated the relative contributions of sediment sources in two paired catchments, one with commercial eucalyptus plantations (0.83 km²) and the other with grassland used for livestock farming (1.10 km²), located in the Brazilian Pampa biome, using different combinations of conventional [geochemical (G), radionuclide (R) and stable isotopes and organic matter properties (S)] and alternative tracer properties [spectrocolorimetric visible-based-colour parameters (V)]. Potential sediment sources evaluated were stream channel, natural grassland and oat pasture fields in the grassland catchment, and stream channel, unpaved roads and eucalyptus plantation in the eucalyptus catchment. The results show that the best combination of tracers to discriminate the potential sources was using GSRV tracers in the grassland catchment, and using GSRV, GSV and GS tracers in the eucalyptus catchment. In all these cases, samples were 100% correctly classified in their respective groups. Considering the best tracers results (GSRV) in both catchments, the sediment source contributions estimated in the catchment with eucalyptus plantations was 63, 30 and 7% for stream channel, eucalyptus stands and unpaved roads, respectively. In the grassland catchment, the source contributions to sediment were 84, 14 and 2% for natural grassland, stream channel and oats pasture fields, respectively. The combination of these source apportionment results with the annual sediment loads monitored during a 3-year period demonstrates that commercial eucalyptus plantations supplied approximately 10 times less sediment (0.1 ton ha⁻¹ year⁻¹) than the traditional land uses in this region, that is, 1.0 ton ha⁻¹ year⁻¹ from grassland and 0.3 ton ha⁻¹ year⁻¹ from oats pasture fields. These results demonstrate the potential of combining conventional and alternative approaches to trace sediment sources originating from different land uses in this region. Furthermore, they show that well-managed forest plantations may be less sensitive to erosion than grassland used for intensive livestock farming, which should be taken into account to promote the sustainable use of land in this region of South America.     

Influence of storm-related sediment storage on the sediment delivery from tributary catchments in the upper Waipaoa River,New Zealand

Although much is known about overall sediment delivery ratios for catchments as components of sediment production and sediment yield, little is known about the component of temporary sediment storage. Sediment delivery ratios focused on the influence of storm-related sediment storage are measured at Matakonekone and Oil Springs tributaries of the Waipaoa River basin, east coast of New Zealand. The terrace deposits of both tributaries show abundant evidence of storm-related sedimentation, especially sediment delivered from Cyclone Bola, a 50 year return rainfall event which occurred in 1988. The sediment delivery ratio is calculated by dividing the volume of sediment transported from a tributary to the main stream by the volume of sediment generated at erosion sites in the tributary catchment. Because the sediment delivery volume is unknown, it can be calculated as the difference between sediment generation volume and sediment storage volume in the channel reach of the tributary. The volume of sediment generated from erosion sites in each tributary catchment was calculated from measurements made on aerial photographs dating from 1960 (1:44 000) and 1988 (1:27 000). The volume of sediment stored in the tributary can be calculated from measurements of cross-sections located along the tributary channel, which are accompanied by terrace deposits dated by counting annual growth rings of trees on terrace surfaces. Sediment delivery ratios are 0·93 for both Matakonekone catchment and Oil Springs catchment. Results indicate that Oil Springs catchment has contributed more than twice the volume of sediment to the Waipaoa River than the Matakonekone catchment (2·75 × 10⁶ m³ vs 1·22 × 10⁶ m³). Although large volumes of sediment are initially deposited during floods, subsequent smaller flows scour away much of these deposits. The sediment scouring rate from storage is 1·25 × 10⁴ m³ a⁻¹ for Matakonekone stream and 0·83 × 10⁴ m³ a⁻¹ for Oil Springs stream. Matakonekone and Oil Springs channels respond to extreme storms by instantaneously aggrading, then gradually excavating the temporarily stored sediment. Results from Matakonekone and Oil Springs streams suggest a mechanism by which event recurrence interval can strongly influence the magnitude of a geomorphic change. Matakonekone stream with its higher stream power is expected to excavate sediment deposits more rapidly and allow more rapid re-establishment of storage capacity. Copyright © 1999 John Wiley & Sons, Ltd.     

Quantification of bank erosion in a drained agricultural lowland catchment

The long‐term and current volumes of sediment exported from stream banks were calculated as potential sources of sediment in a large pond located at the catchment outlet of a small agricultural lowland basin strongly affected by anthropogenic pressure in France. Bank erosion was measured over a short period using a network of erosion pins along a small stream (1400 m long) to quantify the material exported during a single winter (2012–2013). The material exported by this same stream over the last 69 years was quantified using an original approach involving the comparison of a compilation of three‐dimensional historical stream redesign plans that date back to 1944 with the state of the banks in 2013 (differential global positioning system and LiDAR data). The results suggest that a global trend of material loss along the stream banks monitored by erosion pins, with an average erosion rate of 17.7 mm year^?1 and an average volume of exported material of 75 t km^?1. Over 69 years, this same stream exported an average of 36 t km^?1 year^?1, and the average loss of material from the banks throughout the whole catchment was estimated to be 14 t km^?1 year^?1. The contribution of bank material to the filling of the pond over the last 10 years is between 46% and 52% based on an extrapolation of erosion pin dynamics or between 27% and 30% based on the comparison of LiDAR data to the average historical profile extrapolated for the catchment. These results suggest that bank erosion represents a major source of sediment in degraded waters in traditionally understudied agricultural lowland catchments, where anthropogenic pressures are high.     

Flow hydraulics and geomorphic effects of glacial‐lake outburst floods in the Mount Everest region,Nepal

Glacial‐lake outburst floods (GLOFs) on 3 September 1977 and 4 August 1985 dramatically modified channels and valleys in the Mount Everest region of Nepal by eroding, transporting, and depositing large quantities of sediment for tens of kilometres along the flood routes. The GLOF discharges were 7 to 60 times greater than normal floods derived from snowmelt runoff, glacier meltwater, and monsoonal precipitation (referred to as seasonal high flow floods, SHFFs). Specific stream power values ranged from as low as 1900 W m^?2 in wide, low‐gradient valley segments to as high as 51 700 W m^?2 in narrow, high‐gradient valley segments bounded by bedrock. Along the upper 16 km of the GLOF routes, the reach‐averaged specific stream power of the GLOFs was 3·2 to 8·0 times greater than the reach‐averaged specific stream power of the SHFFs. The greatest geomorphic change occurred along the upper 10 to 16 km of the GLOF routes, where the ratio between the GLOF specific stream power and the SHFF specific stream power was the greatest, there was an abundant supply of sediment, and channel/valley boundaries consisted primarily of unconsolidated sediment. Below 11 to 16 km from the source area, the geomorphic effects of the GLOFs were reduced because of the lower specific stream power ratio between the GLOFs and SHFFs, more resistant bedrock flow boundaries, reduced sediment supply, and the occurrence of past GLOFs. Copyright © 2003 John Wiley & Sons, Ltd.     

Nondimensional sediment transport capacity of sand soils and its response to parameter in the Loess Plateau of China

Soil erosion is a major contributor to land degradation in the Loess Plateau in China. To clarify the sediment transport capacity of overland flow influenced by hydraulic parameters, such as shear stress, sand shear stress (hydraulic gradient partition method and hydraulic radius partition method), mean flow velocity, Froude number, stream power, and unit stream power, indoor experiments with eight-unit-width flow discharges from 0.0667 × 10⁻³ to 0.3333 × 10⁻³ m²·s⁻¹, six slope gradients from 3.49 to 20.79%, and two kinds of sand soils (d₅₀ = 0.17 and 0.53 mm) were systematically investigated. A nondimensional method was adopted in data processing. Results showed that there was a partition phenomenon of relation curves because of the different median grain diameters. The correlation between the nondimensional stream power and nondimensional sediment transport capacity was the highest, followed by the correlation between the nondimensional unit stream power and nondimensional sediment transport capacity. However, there was a poor correlation between the flow intensity indices of velocity category and nondimensional sediment transport capacity. Nondimensional stream power, nondimensional unit stream power, and nondimensional shear stress could predict sediment transport capacity well. Ignoring the partition phenomenon of the relation curves, stream power could be used to predict sediment transport capacity, with a coefficient of determination of .85. Furthermore, a general flow intensity index was obtained to predict sediment transport capacity of overland flow. Finally, an empirical formula for predicting sediment transport capacity with a coefficient of determination of .90 was established by multiple regression analyses based on the general flow intensity index. During the analysis between measured sediment transport capacities in present study and predicted values based on Zhang model, Mahmoodabadi model, and Wu model, it was found that these three models could not accurately predict sediment transport capacities of this study because different models are estimated on the basis of different experimental conditions.     

Variations in sediment sources and yields in the Finger Lakes and Catskills regions of New York

The proportional contributions of stream bank and surface sources to fine sediment loads in watersheds in New York State were quantified with uncertainty analysis. Eroding streamside glacial drift, including glaciolacustrine deposits, were examined to help explain variations in the proportional contributions made by bank erosion. Sediment sources were quantified by comparing concentrations of the bomb‐derived radionuclide ¹³⁷Cs in fluvial sediment with sediment from potential source areas such as agricultural soils, forest soils and stream banks. To compare sediment sources in streams containing abundant deposits of fine‐grained glacial drift with watersheds that lacked moderate or extensive streamside deposits, samples were taken from 15 watersheds in the region. The mean contribution of bank erosion to sediment loads in the six streams with glaciolacustrine deposits was 60% (range 46–76%). The proportional contribution of bank erosion was also important in one stream lacking glaciolacustrine deposits (57%) but was less important in the remainder, with contributions ranging from 0 to 46%. Data from this study on the varying contributions of bank erosion and data from past studies of sediment yield in 15 watersheds of New York State suggest that eroding streamside glacial deposits dominate sediment yield in many watersheds. In other watersheds, past impacts to streams, such as channelization, have also resulted in high levels of bank erosion. Copyright © 2007 John Wiley & Sons, Ltd.     

Channel stability and sediment source assessment in streams draining a Piedmont watershed in Georgia,USA

Streams can be classified as stable or unstable, depending on the stage of channel evolution. Many streams of the southern Piedmont in United States have high sediment loads and are listed as impaired under the total maximum daily load (TMDL) program and may be unstable. It is not clear as to what the target (reference) load or remediation measures should be for unstable streams. The objective of this study was to determine the relative channel stability for a typical southern Piedmont stream using rapid geomorphic assessments (RGAs) and sediment yield analysis. The results were supported through a sediment fingerprinting analysis. RGAs were performed along 52 reaches on the North Fork Broad River (NFBR) main stem and two tributaries. Annual sediment yields were calculated and compared with yields in the southern Piedmont for stable streams that are resilient to degradation or aggradation and unstable streams that are susceptible to such disturbances. Majority of the NFBR main stem was found to be unstable with signs of geomorphic instability in the form of degradation and aggradation. The estimated average annual sediment yield was 0·78 T ha^?1 year^?1. By comparison, the median annual yield is 0·20 T ha^?1 year^?1 for stable streams and 0·48 T ha^?1 year^?1 for unstable streams in the Piedmont ecoregion with comparable drainage basin size. We conclude that the NFBR is in an unstable stage of channel evolution. Sediment fingerprinting proved that majority of the stream‐suspended sediment emanated from eroding stream channels. The methods outlined in this study have implications for the reference condition and remediation efforts related to stream turbidity and stream channel restoration. Copyright © 2010 John Wiley & Sons, Ltd.     

Fine sediment delivery and transfer in lowland catchments: modelling suspended sediment concentrations in response to hydrological forcing

Fine sediment delivery to and storage in stream channel reaches can disrupt aquatic habitats, impact river hydromorphology, and transfer adsorbed nutrients and pollutants from catchment slopes to the fluvial system. This paper presents a modelling tool for simulating the time‐dependent response of the fine sediment system in catchments, using an integrated approach that incorporates both land phase and in‐stream processes of sediment generation, storage and transfer. The performance of the model is demonstrated by applying it to simulate in‐stream suspended sediment concentrations in two lowland catchments in southern England, the Enborne and the Lambourn, which exhibit contrasting hydrological and sediment responses due to differences in substrate permeability. The sediment model performs well in the Enborne catchment, where direct runoff events are frequent and peak suspended sediment concentrations can exceed 600 mg l^?1. The general trends in the in‐stream concentrations in the Lambourn catchment are also reproduced by the model, although the observed concentrations are low (rarely exceeding 50 mg l^?1) and the background variability in the concentrations is not fully characterized by the model. Direct runoff events are rare in this highly permeable catchment, resulting in a weak coupling between the sediment delivery system and the catchment hydrology. The generic performance of the model is also assessed using a generalized sensitivity analysis based on the parameter bounds identified in the catchment applications. Results indicate that the hydrological parameters contributing to the sediment response include those controlling (1) the partitioning of runoff between surface and soil zone flows and (2) the fractional loss of direct runoff volume prior to channel delivery. The principal sediment processes controlling model behaviour in the simulations are the transport capacity of direct runoff and the in‐stream generation, storage and release of the fine sediment fraction. The in‐stream processes appear to be important in maintaining the suspended sediment concentrations during low flows in the River Enborne and throughout much of the year in the River Lambourn. Copyright © 2007 John Wiley & Sons, Ltd.     

Sediment transport in Swiss torrents

Sediment loads have been measured in six Swiss mountain torrents over several decades. Most of these torrent catchments are situated in the prealpine belt. They have catchment areas of between 0·5 and 1·7 km². Bedslopes at the measuring sites vary between 5 and 17 per cent, and peak discharges up to 12 m³ s⁻¹ have been recorded. Geophone sensors installed in the Erlenbach stream allow bedload transport activity to be monitored and sediment volumes associated with each flood event to be determined. A detailed analysis of the measurements in this stream results in an empirical equation in which the sediment load per flood event is expressed as a function of the effective runoff volume (discharges above the threshold for bedload motion) and of the normalized peak discharge. For the total of 143 investigated flood events in the Erlenbach stream, the deviation of the predicted from the measured value is within a factor of two for more than two-thirds of all events. A distinction can be made between summer and winter events in analysing the bedload transport events. The summer events, mainly caused by thunderstorms, transport comparatively larger sediment loads than the winter events. For the other investigated streams, the periods of the deposited sediment volume surveys cover in general several flood events. An analysis is performed analogous to that for the Erlenbach stream. The sediment loads show a similar dependency on the two factors effective runoff volume and normalized peak discharge. However, the exponents of these factors in the power law expressions differ from stream to stream. A comparison of the investigated stream shows that some of the variation can be explained by considering the bedslope above the measuring site. The inclusion of a bedslope factor is in agreement with laboratory investigations on bedload transport. © 1997 John Wiley & Sons, Ltd.     

Bedload transport measurements at the Erlenbach stream with geophones and automated basket samplers

In the Erlenbach stream, a pre‐alpine steep channel in Switzerland, sediment transport has been monitored for more than 25 years. Near the confluence with the main valley river, stream flow is monitored and sediment is collected in a retention basin with a capacity of about 2000 m³. The basin is surveyed at regular intervals and after large flood events. In addition, sediment transport has been continuously monitored with piezoelectric bedload impact and geophone sensors since 1986. In 2008–2009, the measuring system in the Erlenbach stream was enhanced by installing an automatic system to obtain bedload samples. Movable metal baskets are mounted on a rail at the downstream wall of the large check dam above the retention basin, and they can be moved automatically into the flow to take bedload transport samples. The wire mesh of the baskets has a spacing of 10 mm to sample all sediment particles coarser than this size (which is about the limiting grain size detected by the geophones). The upgraded measuring system permits to obtain bedload samples over short sampling periods and to measure the grain size distribution of the transported material and its variation over time and with discharge. The analysis of calibration relationships for the geophone measuring system confirms findings from very similar measurements which were performed until 1999 with piezoelectric bedload impact sensors; there is a linear relationship between impulse counts and bedload mass passing over the sensors. Findings from flume experiments are used to discuss the most important factors which affect the calibration of the geophone signal. The bedload transport rates as measured by the moving baskets are among the highest measured in natural streams, with values of the order of several kilograms per meter per second. Copyright © 2012 John Wiley & Sons, Ltd.     

Using a fluvial archive to place extreme flood sediment (dis)connectivity dynamics in context of a longer-term record

The aim of this study was to establish the source and provenance of sediments deposited in a large floodplain sink during extreme floods in the Lockyer Creek catchment, Australia, in 2011 and 2013. We place the sediment source patterns in context of the longer-term record to determine whether coarse-grained sediment sources (i.e., very fine sand to very coarse sand) and the spatio-temporal pattern of (dis)connectivity have changed over time. We do this by matching the geochemical properties and age structure of a sediment profile located in a downstream floodplain sink to the elemental composition of source sediments. One hundred and fifty-seven sediment samples from 20 sites across the catchment are analysed using X-ray fluorescence (XRF) spectrometry to compare the elemental ratio composition of the downstream floodplain sink to its source materials. We use Optically Stimulated Luminescence (OSL) dating to determine the age structure of the sediments in the floodplain sink. The northern tributaries and parts of the Lockyer River trunk stream are the primary sources of coarse sediment. These areas are connected (coupled) to the lower trunk stream and floodplain sediment sink. Southern tributaries are largely disconnected (decoupled) and supply little sediment to the floodplain sediment sink. This pattern of sediment source contribution has remained similar over the last 6.8 ka at least. Sediment sources as observed in the 2011 flood have predominated over the mid-late Holocene whilst those in the 2013 flood are rare.     

Interannual variation of suspended sediment load and sediment yield in an alpine catchment

Abstract

The results are described of 16 years operation of a measuring station for the automatic recording of water discharge, bed load and suspended sediment transport in the Rio Cordon catchment, a small alpine basin (5 km²) located in northeastern Italy. Hillslope erosion processes were investigated by surveying individual sediment sources repeatedly. Annual and seasonal variations of suspended sediment load during the period 1986–2001 are analysed along with their contribution to the total sediment yield. The results show that suspended load accounted for 76% of total load and that most of the suspended sediment transport occurred during two flood events: an extreme summer flash flood in September 1994 (27% of the 16-years total suspended load) and a snowmelt-induced event in May 2001 accompanied by a mud flow which fed the stream with sediments. The role of active sediment source areas is discussed in relation to the changes in flood peak—suspended load trends which became apparent after both the 1994 and the 2001 events.     

Effects of sediment load on hydraulics of overland flow on steep slopes

Eroded sediment may have significant effects on the hydraulics of overland flow, but few studies have been performed to quantify these effects on steep slopes. This study investigated the potential effects of sediment load on Reynolds number, Froude number, flow depth, mean velocity, Darcy–Weisbach friction coefficient, shear stress, stream power, and unit stream power of overland flow in a sand‐glued hydraulic flume under a wide range of hydraulic conditions and sediment loads. Slope gradients were varied from 8·7 to 34·2%, unit flow rates from 0·66 to 5·26×10^?3 m² s^?1, and sediment loads from 0 to 6·95 kg m^?1 s^?1. Both Reynolds number (Re) and Froude number (Fr) decreased as sediment load increased, implying a decrease in flow turbulence. This inverse relationship should be considered in modeling soil erosion processes. Flow depth increased as sediment load increased with a mean value of 1·227 mm, caused by an increase in volume of sediment‐laden flow (contribution 62·4%) and a decrease in mean flow velocity (contribution 37·6%). The mean flow velocity decreased by up to 0·071 m s^?1 as sediment load increased. The Darcy–Weisbach friction coefficient (f) increased with sediment load, showing that the total energy consumption increased with sediment load. The effects of sediment load on f depended on flow discharge: as flow discharge increased, the influence of sediment load on f decreased due to increased flow depth and reduced relative roughness. Flow shear stress and stream power increased with sediment load, on average, by 80·5% and 60·2%, respectively; however, unit stream power decreased by an average of 11·1% as sediment load increased. Further studies are needed to extend and apply the insights obtained under these controlled conditions to real‐world overland flow conditions. Copyright © 2010 John Wiley & Sons, Ltd.     

Streambank sediment loading rates at the watershed scale and the benefit of riparian protection

Streambank erosion is a pathway for sediment and nutrient loading to streams, but insufficient data exist on the magnitude of this source. Riparian protection can significantly decrease streambank erosion in some locations, but estimates of actual sediment load reductions are limited. The objective of this research was to quantify watershed‐scale streambank erosion and estimate the benefits of riparian protection. The research focused on Spavinaw Creek within the Eucha‐Spavinaw watershed in eastern Oklahoma, where composite streambanks consist of a small cohesive topsoil layer underlain by non‐cohesive gravel. Fine sediment erosion from 2003 to 2013 was derived using aerial photography and processed in ArcMap to quantify eroded area. ArcMap was also utilized in determining the bank retreat rate at various locations in relation to the riparian vegetation buffer width. Box and whisker plots clearly showed that sites with riparian vegetation had on average three times less bank retreat than unprotected banks, statistically significant based on non‐parametric t‐tests. The total soil mass eroded from 2003 to 2013 was estimated at 7.27 × 10⁷ kg yr.^?1, and the average bank retreat was 2.5 m yr.^?1. Many current erosion models assume that fluvial erosion is the dominant stream erosion process. Bank retreat was positively correlated with stream discharge and/or stream power, but with considerable variability, suggesting that mass wasting plays an important role in streambank erosion within this watershed. Finally, watershed monitoring programs commonly characterize erosion at only a few sites and may scale results to the entire watershed. Selection of random sites and scaling to the watershed scale greatly underestimated the actual erosion and loading rates. Copyright © 2016 John Wiley & Sons, Ltd.     

Sources and sinks of nutrients in a New Zealand hill pasture catchment II. Phosphorus

The management of the riparian zone has been suggested as a technique for controlling the amounts of phosphorus (P) entering watercourses draining pasture catchments. A study was therefore made of P entering a stream from various sources (rainfall, surface and subsurface derived runoff, direct fallout from aerial topdressing), with the object of providing a rational basis for the design of effective riparian management schemes. P entrained in surface runoff could account for virtually all of the P entering the stream during storms. Approximately 20 per cent of the annual P export from the catchment could be accounted for by direct aerial input of P to the stream during autumn fertilizer topdressing. More than 85 per cent of the P was exported from the catchment as particulate P. Stream sediment had higher P sorption capacities, and were enriched with P relative to the soils from which they were derived. There was a pronounced seasonal variation in sediment enrichment which could be predicted (r² = 0.92) by the logarithm of the rainfall since fertilizer topdressing (LNFERT) and flood intensity. The amount of P lost in streamflow during any flood event was predicted (r² = 0.94) by peak flow, seven day antecedent peak flow and LNFERT. Approximately 40 per cent of the 1.3 kg P ha^?1 exported during 1981 occurred in four storms with recurrence intervals of more than three months. From a P budget compiled from nine events it was hypothesized that the stream acted as a net sink for P at baseflow and low-medium intensity floods but was a source of P at higher flood intensities. It was concluded that P losses from hill pasture catchments could be reduced by avoidance of direct application of P fertilizer to the stream channel, and by fencing out stock from seasonally saturated areas during periods of saturation. The ultimate success of the latter technique would depend on whether buffer vegetation could retain accumulated P during extreme storm events.     

Coarse sediment supply sets the slope of bedrock channels in rapidly uplifting terrain: Field and topographic evidence from eastern Taiwan

The incision rate and steepness of bedrock channels depend on water discharge, uplift rate, substrate lithology, sediment flux, and bedload size. However, the relative role of these factors and the sensitivity of channel steepness to rapid (>1 mm yr⁻¹) uplift rates remain unclear. We conducted field and topographic analyses of fluvial bedrock channels with varying channel bed lithology and sediment source rock along the Coastal Range in eastern Taiwan, where uplift rates vary from 1.8 to 11.8 mm yr⁻¹ and precipitation is relatively consistent (1.5–2.7 m yr⁻¹), to evaluate the controls on bedrock channel steepness. We find that channel steepness is independent of rock uplift rate and annual precipitation but increases monotonically with sediment size and substrate strength. Furthermore, in reaches with uniform substrate lithology (mudstone and flysch), channel steepness systematically varies with sediment source rock but not with channel width. When applied to our data, a mechanistic incision model (saltation-abrasion model) suggests that the steepness of Coastal Range channels is set primarily by coarse-sediment supply. We also observe that larger particles are mainly composed of resistant lithologies derived from volcanic rocks and conglomerates. This result implies that hillslope bedrock properties in the source area exert a dominant control on the steepness of proximal channels through coarse-sediment production in this setting. We propose that channel steepness may be insensitive to uplift rate and flow discharge in fast-uplifting landscapes where incision processes are set by coarse sediment size and supply. Models assuming a proportionality between incision rate and basal shear stress (stream power) may not fully capture controls on fluvial channel profiles in landslide-dominated landscapes. Processes other than channel steepening, such as enhanced bedload impacts and debris-flow scour, may be required to balance rock uplift and incision in these transport-limited systems.