群桩荷载位移特性研究

将杆系结构有限单元法与荷载传递迭代法相耦合,形成一桩基沉降分析计算的混合法。采用近似解析解中Randolph and Wroth’Model与双曲线模型相结合,模拟桩身与桩周介质边界上剪切滑移的非线性。桩间相互作用在采用弹性理论Mindlin方程解答计算,并考虑了桩间“加筋与遮帘”作用。桩周土介质非均质性特征,采用指数函数模拟。分析了刚性承台下群桩桩数、桩长、桩间距和桩土模量比等群桩工作特性的影响。尤其是桩台基础沉降对群桩相互作用影响机制的研究,对桥梁拼接等对桩基础沉降要求严格的工程有重要的借鉴意义。     

Axial and lateral response of pile groups embedded in nonhomogeneous soils

A numerical method of analysis based on elasticity theory is presented for the analysis of axially and laterally loaded pile groups embedded in nonhomogeneous soils. The problem is decomposed into two systems, namely the group piles acted upon by external applied loads and pile–soil interaction forces, and a layered soil continuum acted upon by a system of pile–soil interaction forces at the imaginary positions of the piles. The group piles are discretized into discrete elements while the nonhomogeneous soil behaviour is determined from an economically viable finite element procedure. The load–deformation relationship of the pile group system is then determined by considering the equilibrium of the pile–soil interaction forces, and the compatibility of the pile and soil displacements. The influence of soil nonlinearity can be studied by limiting the soil forces at the pile–soil interface, and redistributing the ‘excess forces’ by an ‘initial stress’ process popular in elasto-plastic finite element analysis. The solutions from this approach are compared with some available published solutions for single piles and pile groups in homogeneous and nonhomogeneous soils. A limited number of field tests on pile groups are studied, and show that, in general, the computed response compares favourably with the field measurements.     

群桩扭转非线性模型

建立了一个非线性数学模型来分析群桩扭转问题。该模型利用非线性荷载传递曲线来模拟桩的非线性响应,采用Mindlin解计算各桩水平力间的相互作用,用Randolph解析解分析得到各桩间扭矩对水平力的影响。在各单桩中引入经验性的耦合系数,分析桩身水平变形引起的土体反力对该桩扭转承载力的影响。对比计算结果与离心机模型试验数据,表明该模型能够模拟群桩扭转中主要的桩-土-桩相互作用和荷载耦合作用,较好地反映了实际情况。     

双排微型桩加固碎石土滑坡物理模型试验研究

通过3组不同桩间距下双排微型桩加固碎石土滑坡室内模型试验,研究微型桩受力变形特性和滑坡推力传递规律。试验结果表明:双排微型桩承受的滑坡推力主要集中在滑面以上1/3桩身范围内,桩身最大弯矩位于滑面附近,且桩群均以第一排桩达到其弹性受力极限而失效;桩间距为5d时,微型桩群对桩间土的遮蔽阻挡效果最好,桩群能承受的滑坡推力最大,且桩顶位移最小,滑坡推力在排桩间分布最合理,其传递系数α在（0.5,0.7）间取值。     

Experimental investigation of the behavior of pile groups in sand under different loading rates

The behavior of pile groups in sand under different loading rates is investigated. A total of 60 tests were conducted in the laboratory using model steel piles embedded in a medium dense sand. The model piles have an outside diameter of 25 mm and embedment length of 500 mm. Five different configurations of pile groups (2 × 1, 3 × 1, 2 × 2, 2 × 3, 3 × 3) with center to center spacing between the piles of 3d, 6d and 9d (d is the pile diameter) were tested. The piles were subjected to axial compressive loads under four different loading rates: 1.0, 0.5, 0.1 and 0.05 mm/min. Test results indicated that the axial compressive capacity of pile group increases with the loading rate such that the pile capacity versus logarithm of loading rate data plot approximately along a straight line. The slope of this line increases as the number of piles in a group increases and it decreases by increasing the spacing between piles in a group.     

Response evaluation for horizontally loaded fixed‐head pile groups using 3‐D non‐linear analysis

The response of laterally loaded pile foundations may be significantly important in the design of structures for such loads. A static horizontal pile load test is able to provide a load–deflection curve for a single free‐head pile, which significantly differs from that of a free‐ or fixed‐head pile group, depending on the particular group configuration. The aim of this paper is to evaluate the influence of the interaction between the piles of a group fixed in a rigid pile cap on both the lateral load capacity and the stiffness of the group. For this purpose, a parametric three‐dimensional non‐linear numerical analysis was carried out for different arrangements of pile groups. The response of the pile groups is compared to that of the single pile. The influence of the number of piles, the spacing and the deflection level to the group response is discussed. Furthermore, the contribution of the piles constituting the group to the total group resistance is examined. Finally, a relationship is proposed allowing a reasonable prediction of the response of fixed‐head pile groups at least for similar soil profile conditions. Copyright © 2005 John Wiley & Sons, Ltd.     

公路桥超长群桩的有效桩长研究

针对公路桥梁超长群桩的有效桩长问题,对国内公路桥梁桩基的荷载状况进行统计分析,得出桩顶应力主要分布在6～21 MPa范围。进行了长径比为96的桩间距分别为3D、4.5D和6D的3组不同群桩的超长群桩模型试验,得到3种不同桩间距的超长群桩中单桩轴力随着不同荷载的分布图,按照桩身轴力趋于0的桩截面的深度确定有效桩长,并利用指数函数关系分别拟合了3种不同桩间距的桩顶应力与有效桩长之间的关系。根据竖向荷载作用下群桩模型试验与实际原型之间的相似关系,确定公路桥超长群桩与荷载对应的有效桩长取值范围,研究了超长群桩的有效桩长与桩间距之间的关系,并对桥梁桩基有效桩长的取值与桩间距提出了建议。     

水平偏心受荷群桩p乘子计算

水平偏心受荷群桩同时发生水平移动和绕承台中心的转动,使基桩的运动方向各不相同,因此基桩的运动方向成为影响群桩效应的一个关键因素。研究发现：水平偏心受荷的两根桩,前桩运动方向与两桩连线夹角0o≤η≤90o,后桩夹角?90o≤θ≤90o;量化两桩间桩?土?桩相互作用的折减系数与η和θ密切相关,η和θ组合存在一个范围,在该范围内两桩不存在相互作用;当两桩存在相互作用时,相互作用对后桩的影响往往大于对前桩的影响。通过将定量描述水平受荷群桩群桩效应的p乘子概念拓展到水平偏心受荷群桩,综合运用理论分析、试验和数值计算成果,提出了折减系数计算公式,进而给出了广义p乘子经验计算公式。通过试验案例验证了该计算公式的合理性。     

Numerical Analysis of Pile–Soil–Pile Interaction in Pile Groups with Batter Piles

Battered piles are usually used to counteract lateral forces in a pile group. As there is little spacing between piles, they are affected by one another, and there is interaction between them. In this study, pile–soil–pile interaction in a group of battered piles was numerically simulated using finite element analysis. Double and frictional pile groups under static lateral and axial loadings were analyzed separately. The effects of batter angle, slenderness ratio, spacing between piles, pile–soil stiffness ratio, and soil plasticity on interaction factors were computed and presented in curves.     

考虑沉桩效应的群桩非线性荷载-沉降解析

考虑沉桩效应对桩周土体力学特性的影响,采用指数函数型荷载传递曲线分别建立了静压桩的桩侧和桩端荷载传递模型。在此基础上,根据群桩加载过程中桩周土体的变形模式,基于荷载传递法描述桩-土界面的非线性行为,采用剪切位移法考虑群桩之间的相互作用,提出了考虑沉桩效应的群桩非线性荷载-沉降混合计算方法。通过开展离心模型试验对该计算方法解答进行了验证,研究了沉桩效应和桩-土界面非线性特征对群桩承载特性的影响。研究结果表明,沉桩效应对桩周土体起到挤密作用,使得桩周土体的强度和刚度增大,从而提高了群桩的承载特性。群桩加载过程中桩-土界面刚度随沉降变形而逐渐减小,使得群桩荷载-沉降曲线呈现出明显的非线性特征。     

On the influence of vertical loads on the lateral response of pile foundation

The influence of vertical loads on the lateral response of group piles installed in sandy soil and connected together by a concrete cap is studied through finite elements analyses. The analyses focus on the five piles in the middle row of 3 × 5 pile groups. The vertical load is applied by enforcing a vertical displacement equivalent to 2% of the pile diameter through the pile cap prior to the application of the lateral loads. The results have shown that the lateral resistance of the leading pile (pile 1) does not appear to vary considerably with the vertical load. However, the vertical load leads to 23%, 36%, 64%, and 82% increase in the lateral resistance of piles 2–5, respectively. The increase in the lateral pressures in the sand deposit is the major driving factor to contribute the change in the lateral resistance of piles, depending on the position of the pile in the group. The distribution of lateral loads among piles in the group tends to be more uniform when vertical loads were considered leading to a more economical pile foundation design.     

Negative skin friction on pile groups

A numerical procedure is presented for the downdrag analysis of group piles which penetrate a consolidating upper soil layer to socket into a firm bearing stratum of finite stiffness. The settlement of the consolidating upper soil layer under a surcharge load is estimated using Terzaghi's one-dimensional consolidation theory. Parametric solutions are presented to show the influence of various parameters on the performance of the socketed pile groups in terms of the development of the induced downdrag forces and associated pile head settlements. In general, pile–soil–pile interaction has the beneficial effect of reducing the downdrag forces and settlements of the group piles when compared to the corresponding single pile values, provided that the soil settlements are not so large as to cause full slippage at the interface in all the piles. Reasonable agreement is obtained between the theoretical and experimental results for pile groups subjected to negative skin friction.     

Updating reliability of single piles and pile groups by load tests

Pile load tests are used to refine designs and for quality assurance. They can also be used to verify the reliability of piles and pile groups. Stochastic methods have previously been developed to verify the reliability of single piles. A general stochastic method to verify the reliability of pile groups is developed in this paper. The method can be used to assess the reliability of groups where pile tests have been conducted to the ultimate capacity, to below the ultimate capacity but exceeding specified capacity, and where pile tests fail to achieve the specified capacity. In the latter case, the method allows decisions to be made as to whether the reliability of the entire pile group is satisfactory or whether additional piles need to be installed.     

Experimental and numerical investigations on the performance of sacrificial piles in reducing local scour around pile groups

This paper presents both experimental study and numerical simulation to investigate the effects of an innovative sacrificial piles concept to reduce local scour surrounding service piles. These sacrificial piles are placed upstream of the pile groups, which serves to change the flow field and reduce the erosive force before it reaches the service piles. Four types of pile group arrangements were considered in the experimental and simulation analyses, including single pile, double pile in tandem arrangements, double pile with side-by-side arrangements, and pile array of 2 × 2 arrangements. Scaled experiments were conducted in flume for each group of design, and local scour around piles with and without sacrificial piles was monitored. It was found that the sacrificial piles effectively reduced the development of local scour surrounding the service piles, especially at their heels. The results also showed that the use of sacrificial piles reduced the time required for the scour depth to reach the equilibrium conditions than those without the sacrificial piles. To corroborate the experimental observation, numerical simulation with three-dimensional computational fluid dynamics model has also been carried out with commercial code with verified erosion model. The development of dynamic scour process and maximum scour depth were obtained by the computational simulations. Comparison of experimental and computational results both indicates that the use of sacrificial pile is effective in reducing the scour depth. The extent of reduction in the maximum scour depth varied with the arrangement of sacrificial piles.     

Response evaluation of axially loaded fixed‐head pile groups in clayey soils

The aim of this paper is to investigate the interaction between the piles in a group with a rigid head and correlate the response of a group of piles to that of a single pile. For this purpose, a computationally intensive study using 3‐D nonlinear numerical analysis was carried out for different pile group arrangements in clayey soils. The responses of the groups of piles were compared with that of a single pile and the variation of the settlement amplification factor R_a was then quantified. The influence of the number of piles, the spacing, and the settlement level on the group response is discussed. A previously proposed relationship for predicting the response of a pile group, based on its configuration and the response of a single pile, has been modified to extend its applicability for any pile spacing. The modified relationship provides a reasonable prediction for various group configurations in clayey soils. Copyright © 2009 John Wiley & Sons, Ltd.     

能量桩群桩工作特性简化分析方法研究

采用双曲线模型模拟桩土界面上的力学行为,利用剪切位移法反映剪应力在土层中的传递,考虑群桩之间的相互作用,建立了热?力耦合作用下能量桩群桩基础工作特性的简化分析方法。该方法能反映桩土界面上的非线性、桩顶的约束条件和能量桩位置的影响,可直接计算所有桩的位移和轴力。与现有方法相比,计算得到的双桩相互作用因子更加合理。通过与文献中试验数据的对比表明,若只有局部桩经历温度变化,能量桩运行过程中各桩之间存在差异变形,基础出现倾斜,桩顶荷载发生重分布。所建立方法计算方便,能合理模拟能量桩群桩基础的主要工作特性,可用于大规模能量桩群桩基础的设计计算。     

Response of Pile Groups Driven in Sand Subjected to Combined Loads

Although the loads applied on piles are usually a combination of both vertical and lateral loads, very limited experimental research has been done on the response of pile groups subjected to combined loads. Due to pile–soil–pile interaction in pile groups, the response of a pile group may differ substantially from that of a single pile. This difference depends on soil state and pile spacing. This paper presents results of experiments designed to investigate pile interaction effects on the response of pile groups subjected to both axial and lateral loads. The experiments were load tests performed on model pile groups (2 × 2 pile groups) in calibration chamber sand samples. The model piles were driven into the sand samples prepared with different relative densities using a sand pluviator. The combined load tests were performed on the model pile groups subjected to different axial load levels, i.e., 0 (pure lateral loading), 25, 50, and 75% of the ultimate axial load capacity of the pile groups, defined as the load corresponding to a settlement of 10% of the model pile diameter. The combined load test results showed that the bending moment and lateral deflection at the head of the piles increased substantially for tests performed in the presence of axial loads, suggesting that the presence of axial loads on groups of piles driven in sand is detrimental to their lateral capacity.     

Three‐dimensional finite element analysis of the interaction between tunneling and pile foundations

This paper concerns analysis of the impact of construction of urban tunnels on adjacent pile foundations. It is carried out using an elastoplastic three‐dimensional finite element modelling. Numerical simulations are performed in two stages, which concern, respectively, the application of the pile axial loading and the construction of the tunnel in presence of the pile foundations. Analysis is carried out for both single piles and groups of piles. Results of numerical simulations show that tunneling induces significant internal forces in adjacent piles. The distribution of internal forces depends mainly on the position of the pile tip regarding the tunnel horizontal axis and the distance of the pile axis from the centre of the tunnel. Analysis of the interaction between tunneling and a group of piles reveals a positive group effect with a high reduction of the internal forces in rear piles. Copyright © 2002 John Wiley & Sons, Ltd.     

Nonlinear response of laterally loaded piles and pile groups

In spite of extensive studies on laterally loaded piles carried out over years, none of them offers an expedite approach as to gaining the nonlinear response and its associated depth of mobilization of limiting force along each pile in a group. To serve such a need, elastic–plastic solutions for free‐head, laterally loaded piles were developed recently by the author. They allow the response to be readily computed from elastic state right up to failure, by assigning a series of slip depths, and a limiting force profile. In this paper, equivalent solutions for fixed‐head (FixH) single piles were developed. They are subsequently extended to cater for response of pile groups by incorporating p‐multipliers. The newly established solutions were substantiated by existing numerical solutions for piles and pile groups. They offer satisfactory prediction of the nonlinear response of all the 6 single piles and 24 pile groups investigated so far after properly considering the impact of semi‐FixH restraints. They also offer the extent to ultimate state of pile groups via the evaluated slip depths. The study allows ad hoc guidelines to be established for determining input parameters for the solutions. The solutions are tailored for routine prediction of the nonlinear interaction of laterally loaded FixH piles and capped pile groups. Copyright © 2008 John Wiley & Sons, Ltd.     

Centrifuge shaking table tests on 4 × 4 pile groups in liquefiable ground

A series of centrifuge shaking table model tests are conducted on 4?×?4 pile groups in liquefiable ground in this study, achieving horizontal–vertical bidirectional shaking in centrifuge tests on piles for the first time. The dynamic distribution of forces on piles within the pile groups is analysed, showing the internal piles to be subjected to greater bending moment compared with external piles, the mechanism of which is discussed. The roles of superstructure–pile inertial interaction and soil–pile kinematic interaction in the seismic response of the piles within the pile groups are investigated through cross-correlation analysis between pile bending moment, soil displacement, and structure acceleration time histories and by comparing the test results on pile groups with and without superstructures. Soil–pile kinematic interaction is shown to have a dominant effect on the seismic response of pile groups in liquefiable ground. Comparison of the pile response in two tests with and without vertical input ground motion shows that the vertical ground motion does not significantly influence the pile bending moment in liquefiable ground, as the dynamic vertical total stress increment is mainly carried by the excess pore water pressure. The influence of previous liquefaction history during a sequence of seismic events is also analysed, suggesting that liquefaction history could in certain cases lead to an increase in liquefaction susceptibility of sand and also an increase in dynamic forces on the piles.