Infiltration efficiency in sprinkler irrigation

The term ‘infiltration efficiency’ is proposed to incorporate the losses due to surface runoff in sprinkler irrigation. Infiltration efficiency is calculated analytically using Kostiakov's empirical equation. A dimensionless graph for computing infiltration efficiency and a numerical application of the theory to sprinkler design are also included.     

Infiltration at the Tai rain forest (Ivory Coast): Measurements and modelling

Infiltration experiments have been performed at three sites along a well-known catena under virgin tropical rain forest using a portable sprinkling infiltrometer. Experimentally determined infiltration curves are presented. Infiltration curves are also simulated on the basis of the Mein-Larson equation. The parameters for this model have been obtained from the infiltration curves (saturated conductivity) and simple soil moisture determinations (fillable porosity). The agreement between experimentally determined and modelled infiltration is reasonable, provided (a) saturated conductivity as derived from the experimental data is corrected, (b) a storage parameter, also derived from the experimental data, is added to the Mein-Larson model, and (c) the decline in soil porosity with depth is either small or occurs abruptly at shallow depth. Comparison of observed infiltration rates with rainfall intensity shows that Horton Overland Flow has to occur naturally at least on the middle and lower section of the catena. Despite the fact that most parameters can be estimated in principle from basic soil data, it remains advisable to obtain sprinkling infiltrometer field measurements, because of soil variability due to dynamic surface conditions, macroporosity, air entrapment, and irregularity of the wetting front.     

Determining hydraulic properties of a loam soil by alternative infiltrometer techniques

Testing infiltrometer techniques to determine soil hydraulic properties is necessary for specific soils. For a loam soil, the water retention and hydraulic conductivity predicted by the BEST (Beerkan Estimation of Soil Transfer parameters) procedure of soil hydraulic characterization was compared with data collected by more standard laboratory and field techniques. Six infiltrometer techniques were also compared in terms of saturated soil hydraulic conductivity, K_s. BEST yielded water retention values statistically similar to those obtained in the laboratory and K_s values practically coinciding with those determined in the field with the pressure infiltrometer (PI). The unsaturated soil hydraulic conductivity measured with the tension infiltrometer (TI) was reproduced satisfactorily by BEST only close to saturation. BEST, the PI, one‐potential experiments with both the TI and the mini disk infiltrometer (MDI), the simplified falling head (SFH) technique and the bottomless bucket (BB) method yielded statistically similar estimates of K_s, differing at the most by a factor of three. Smaller values were obtained with longer and more soil‐disturbing infiltration runs. Any of the tested infiltration techniques appears usable to obtain the order of magnitude of K_s at the field site, but the BEST, BB and PI data appear more appropriate to characterize the soil at some stage during a rainfall event. Additional investigations on both similar and different soils would allow development of more general procedures to apply infiltrometer techniques for soil hydraulic characterization. Copyright © 2015 John Wiley & Sons, Ltd.     

Difference infiltrometer: a method to measure temporally variable infiltration rates during rainstorms

We developed a difference infiltrometer to measure time series of non‐steady infiltration rates during rainstorms at the point scale. The infiltrometer uses two, tipping bucket rain gages. One gage measures rainfall onto, and the other measures runoff from, a small circular plot about 0.5‐m in diameter. The small size allows the infiltration rate to be computed as the difference of the cumulative rainfall and cumulative runoff without having to route water through a large plot. Difference infiltrometers were deployed in an area burned by the 2010 Fourmile Canyon Fire near Boulder, Colorado, USA, and data were collected during the summer of 2011. The difference infiltrometer demonstrated the capability to capture different magnitudes of infiltration rates and temporal variability associated with convective (high intensity, short duration) and cyclonic (low intensity, long duration) rainstorms. Data from the difference infiltrometer were used to estimate saturated hydraulic conductivity of soil affected by the heat from a wildfire. The difference infiltrometer is portable and can be deployed in rugged, steep terrain and does not require the transport of water, as many rainfall simulators require, because it uses natural rainfall. It can be used to assess infiltration models, determine runoff coefficients, identify rainfall depth or rainfall intensity thresholds to initiate runoff, estimate parameters for infiltration models, and compare remediation treatments on disturbed landscapes. The difference infiltrometer can be linked with other types of soil monitoring equipment in long‐term studies for detecting temporal and spatial variability at multiple time scales and in nested designs where it can be linked to hillslope and basin‐scale runoff responses. Published 2012. This article is a U.S. Government work and is in the public domain in the USA.     

Analysing tension infiltrometer data from sloped surface using two‐dimensional approximation

Tension infiltrometers allow water to infiltrate into the soils at various specified pressure heads. The resulting infiltration rates can then be analysed for soil hydraulic properties by either analytical or inverse numerical methods. Tension infiltrometers however are primarily designed to be deployed on horizontal land surfaces, and their applications have been studied widely using an inverse numerical tool HYDRUS‐2D. However, natural landscapes are often nonhorizontal, and infiltration through tension infiltrometers on sloped surfaces is no longer an axisymmetrical two‐dimensional (2D) process but a fully three‐dimensional (3D) one. In addition, minimal research has examined the effect of simplifying the 3D problem to a 2D one on the hydraulic conductivity estimated using tension infiltrometer data from different land slopes of various soil types. Therefore, in this study, tension infiltrometer data on different slopes have been obtained from a catchment located at National University of Singapore. In addition, tension infiltrometer data of six soil types on different slopes and with different initial water content were simulated using HYDRUS‐3D. Combining field measurements, forward and inverse modelling, the influence of applying a 2D approximation on hydraulic property estimations using tension infiltrometer data was examined. The results show that the estimations for soils with high infiltration rates are more sensitive to application of the 2D approximation. The maximum allowable slopes for employing 2D approximation on clayey and sandy soils are 25° and less than 3°, respectively. Furthermore, the maximum allowable slope decreases with decreasing initial water content. Copyright © 2012 John Wiley & Sons, Ltd.     

Comparing Beerkan infiltration tests with rainfall simulation experiments for hydraulic characterization of a sandy‐loam soil

Saturated soil hydraulic conductivity, K _s , data collected by ponding infiltrometer methods and usual experimental procedures could be unusable for interpreting field hydrological processes and particularly rainfall infiltration. The K _s values determined by an infiltrometer experiment carried out by applying water at a relatively large distance from the soil surface could however be more appropriate to explain surface runoff generation phenomena during intense rainfall events. In this study, a link between rainfall simulation and ponding infiltrometer experiments was established for a sandy‐loam soil. The height of water pouring for the infiltrometer run was chosen, establishing a similarity between the gravitational potential energy of the applied water, E _p , and the rainfall kinetic energy, E _k . To test the soundness of this procedure, the soil was sampled with the Beerkan estimation of soil transfer parameters procedure of soil hydraulic characterization and two heights of water pouring (0.03 m, i.e., usual procedure, and 0.34 m, yielding E _p  = E _k ). Then, a comparison between experimental steady‐state infiltration rates, i _sR , measured with rainfall simulation experiments determining runoff production and K _s values for the two water pouring heights was carried out in order to discriminate between theoretically possible (i _sR  ≥ K _s ) and impossible (i _sR  < K _s ) situations. Physically possible K _s values were only obtained by applying water at a relatively large distance from the soil surface, because i _sR was equal to 20.0 mm h^?1 and K _s values were 146.2–163.9 and 15.2–18.7 mm h^?1 for a height of water pouring of 0.03 and 0.34 m, respectively. This result suggested the consistency between Beerkan runs with a high height of water pouring and rainfall simulator experiments. Soil compaction and mechanical aggregate breakdown were the most plausible physical mechanisms determining reduction of K _s with height. This study demonstrated that the height from which water is poured onto the soil surface is a key parameter in infiltrometer experiments and can be adapted to mimic the effect of high intensity rain on soil hydraulic properties.     

Characteristics of concentrated flow hydraulics for rangeland ecosystems: implications for hydrologic modeling

Concentrated flow is often the dominant source of water erosion following disturbance on rangelands. Because of the lack of studies that explain the hydraulics of concentrated flow on rangelands, cropland‐based equations have typically been used for rangeland hydrology and erosion modeling, leading to less accurate predictions due to different soil and vegetation cover characteristics. This study investigates the hydraulics of concentrated flow using unconfined field experimental data over diverse rangeland landscapes within the Great Basin Region, United States. The results imply that the overall hydraulics of concentrated flow on rangelands differ significantly from those of cropland rills. Concentrated flow hydraulics on rangelands are largely controlled by the amount of cover or bare soil and hillslope angle. New predictive equations for concentrated flow velocity (R² = 0·47), hydraulic friction (R² = 0·52), and width (R² = 0·4) representing a diverse set of rangeland environments were developed. The resulting equations are applicable across a wide span of ecological sites, soils, slopes, and vegetation and ground cover conditions and can be used by physically‐based rangeland hydrology and erosion models to estimate rangeland concentrated flow hydraulic parameters. Published in 2011. This article is a US Government work and is in the public domain in the USA.     

Downstream effects of stream flow diversion on channel characteristics and riparian vegetation in the Colorado Rocky Mountains,USA

Flow diversions are widespread and numerous throughout the semi‐arid mountains of the western United States. Diversions vary greatly in their structure and ability to divert water, but can alter the magnitude and duration of base and peak flows, depending upon their size and management. Channel geometry and riparian plant communities have adapted to unique hydrologic and geomorphic conditions existing in the areas subject to fluvial processes. We use geomorphic and vegetation data from low‐gradient (≤3%) streams in the Rocky Mountains of north‐central Colorado to assess potential effects of diversion. Data were collected at 37 reaches, including 16 paired upstream and downstream reaches and five unpaired reaches. Channel geometry data were derived from surveys of bankfull channel dimensions and substrate. Vegetation was sampled using a line‐point intercept method along transects oriented perpendicular to the channel, with a total of 100 sampling points per reach. Elevation above and distance from the channel were measured at each vegetation sampling point to analyze differences in lateral and vertical zonation of plant communities between upstream and downstream reaches. Geomorphic data were analyzed using mixed effects models. Bankfull width, depth, and cross‐sectional area decreased downstream from diversions. Vegetation data were analyzed using biological diversity metrics, richness, evenness and diversity, as well as multivariate community analysis. Evenness increased downstream from diversions, through reduced frequency of wetland indicator species and increased frequency of upland indicator species. Probability of occurrence for upland species downstream of a diversion increases at a greater rate beginning around 0·5 m above active channel. The results suggest that channel morphology and riparian plant communities along low‐gradient reaches in montane environments in the Colorado Rocky Mountains are impacted by diversion‐induced flow alteration, with the net effect of simplifying and narrowing the channel and homogenizing and terrestrializing riparian plant communities. Copyright © 2014 John Wiley & Sons, Ltd.     

Soil macroporosity and infiltration characteristics of a forest podzol

Spatial distribution of soil macroporosity was determined for a forest podzol from tension infiltrometer measurements at the soil surface. Surface‐derived macroporosity values were compared with point infiltration characteristics obtained from soil water content and soil water chemistry measurements during an experimental irrigation, and with parameters of a kinematic wave model applied to soil water content data. Macroporosity estimated by the tension infiltrometer ranged from 0·00087 to 0·0219% of soil volume, and infiltration at these two sites was dominated by propagation of a well‐defined wetting front through the soil profile and bypass flow via soil macropores, respectively. Infiltration at sites with intermediate macroporosities reflected a combination of these two processes, although results were inconclusive at one site owing to lateral flow at the base of the soil profile. There was no agreement between macroporosities estimated by the tension infiltrometer and the kinematic wave model. The maximum soil conductance parameter within the profile at a site, however, was related directly to the surface‐derived macroporosity. The partial agreement between surface‐derived macroporosity estimates and point infiltration characteristics shown here supports the use of tension infiltrometry as a rapid, non‐destructive method of assessing spatial variations in the relative contribution of macropore flow to the infiltration process. Copyright © 2000 John Wiley & Sons, Ltd.     

Modelling of infiltration using artificial intelligence techniques in semi-arid Iran

ABSTRACT

Infiltration plays a fundamental role in streamflow, groundwater recharge, subsurface flow, and surface and subsurface water quality and quantity. In this study, adaptive neuro-fuzzy inference system (ANFIS), support vector machine (SVM) and random forest (RF) models were used to determine cumulative infiltration and infiltration rate in arid areas in Iran. The input data were sand, clay, silt, density of soil and soil moisture, while the output data were cumulative infiltration and infiltration rate, the latter measured using a double-ring infiltrometer at 16 locations. The results show that SVM with radial basis kernel function better estimated cumulative infiltration (RMSE = 0.2791 cm) compared to the other models. Also, SVM with M4 radial basis kernel function better estimated the infiltration rate (RMSE = 0.0633 cm/h) than the ANFIS and RF models. Thus, SVM was found to be the most suitable model for modelling infiltration in the study area.     

Alternative analysis of transient infiltration experiment to estimate soil water repellency

The repellency index (RI) defined as the adjusted ratio between soil‐ethanol, S_e, and soil‐water, S_w, sorptivities estimated from minidisk infiltrometer experiments has been used instead of the widely used water drop penetration time and molarity of ethanol drop tests to assess soil water repellency. However, sorptivity calculated by the usual early‐time infiltration equation may be overestimated as the effects of gravity and lateral capillary are neglected. With the aim to establish the best applicative procedure to assess RI, different approaches to estimate S_e and S_w were compared that make use of both the early‐time infiltration equation (namely, the 1 min, S1, and the short‐time linearization approaches), and the two‐term axisymmetric infiltration equation, valid for early to intermediate times (namely, the cumulative linearization and differentiated linearization approaches). The dataset included 85 minidisk infiltrometer tests conducted in three sites in Italy and Spain under different vegetation habitats (forest of Pinus pinaster and Pinus halepensis, burned pine forest, and annual grasses), soil horizons (organic and mineral), postfire treatments, and initial soil water contents. The S1 approach was inapplicable in 42% of experiments as water infiltration did not start in the first minute. The short‐time linearization approach yielded a systematic overestimation of S_e and S_w that resulted in an overestimation of RI by a factor of 1.57 and 1.23 as compared with the cumulative linearization and differentiated linearization approaches. A new repellency index, RI_s, was proposed as the ratio between the slopes of the linearized data for the wettable and hydrophobic stages obtained by a single water infiltration test. For the experimental conditions considered, RI_s was significantly correlated with RI and WDPT. Compared with RI, RI_s includes information on both soil sorptivity and hydraulic conductivity and, therefore, it can be considered more physically linked to the hydrological processes affected by soil water repellency.     

Intensive infiltrometer studies on a plowed big sagebrush site

Intensive infiltrometer studies were made over a 4-year period on a plowed big sagebrush (Artemisia tridentata) site in southern Idaho. Results of the study indicate there was a natural decay in absorptive capabilities of surface soils due to the plowing treatment. The apparent result of grazing was not to reduce the minimal infiltration capacities measured on the respective site, but rather to eliminate seasonal trends so that infiltration rates were at the low end of the scale throughout the year. Grazing did not increase sediment production potentials beyond the increases expected as a result of mechanical disturbance associated with plowing. Attempts at predicting infiltration rates and potential sediment production indicated that easily measured soil cover characteristics do not adequately reflect the potential (actual) hydrologic performance of a big sagebrush site which has been grossly modified by activity such as plowing or grazing.     

The influence of litho-stratification on the infiltrating water front in a granite terrain

Abstract

Under a sustainable groundwater development and quality management project over a semi-arid granite terrain, several rainwater harvesting structures were proposed based on geophysical investigations in the study area. In order to validate the site suitability and check the efficacy of the recommended recharge structures in terms of source sustainability, certain hydrological tests, such as infiltration studies, were conducted within the recharge area of these structures. Infiltration rate estimation using a double-ring infiltrometer normally results in an exponential decay relationship with high initial infiltration rate followed by gradual reduction until, ultimately, a stabilized rate is attained. In this paper, we present the results of infiltration tests conducted using a double-ring infiltrometer (under constant head condition) within the tank bed area of a proposed percolation tank site. The results showed unique features in the infiltration rate at different time intervals within the total experimental period: a staircase-like evolution with intermittent stabilization for a short duration. Based on the integrated approach of geophysical investigations, hydrological tests, and supported by physical evidence, the infiltration behaviour observed over the study area was considered to be due to the lithological stratification with different permeability and textural conditions.

Citation Andrade, R. & Muralidharan, D. (2011) The influence of litho-stratification on the infiltrating water front in a granite terrain. Hydrol. Sci. J. 56(5), 907–915.     

A comparison between the single ring pressure infiltrometer and simplified falling head techniques

Testing the relative performances of the single ring pressure infiltrometer (PI) and simplified falling head (SFH) techniques to determine the field saturated soil hydraulic conductivity, K_fs, at the near point scale may help to better establish the usability of these techniques for interpreting and simulating hydrological processes. A sampling of 10 Sicilian sites showed that the measured K_fs was generally higher with the SFH technique than the PI one, with statistically significant differences by a factor varying from 3 to 192, depending on the site. A short experiment with the SFH technique yielded higher K_fs values because a longer experiment with the PI probably promoted short‐term swelling phenomena reducing macroporosity. Moreover, the PI device likely altered the infiltration surface at the beginning of the run, particularly in the less stable soils, where soil particle arrangement may be expected to vary upon wetting. This interpretation was supported by a soil structure stability index, SSI, and also by the hydraulic conductivity data obtained with the tension infiltrometer, i.e. with a practically negligible disturbance of the sampled soil surface. In particular, a statistically significant, increasing relationship with SSI and an unsaturated conductivity greater than the saturated one were only detected for the K_fs data obtained with the PI. The SFH and PI techniques should be expected to yield more similar results in relatively rigid porous media (low percentages of fine particles and structurally stable soils) than in soils that modify appreciably their particle arrangement upon wetting. The simultaneous use of the two techniques may allow to improve K_fs determination in soils that change their hydrodynamic behaviour during a runoff producing rainfall event. Copyright © 2013 John Wiley & Sons, Ltd.     

Influence of spatial variations of microtopography and infiltration on surface runoff and field scale hydrological connectivity

Surface runoff on agricultural fields arises when rainfall exceeds infiltration. Excess water ponding in and flowing through local microtopography increases the hydrological connectivity of fields. In turn, an increased level of hydrological connectivity leads to a higher surface runoff flux at the field boundaries. We investigated the functional hydrological connectivity of synthetical elevation fields with varying statistical properties. For this purpose, we developed an object-oriented ponding and redistribution model to which Philip’s infiltration model was coupled. The connectivity behaviour is determined by the presence of depressions with a large area and spatial organization of microtopography in rills or channels. The presence of microdepressions suppresses the effect of the spatial variation of infiltration properties. Connectivity behaviour of a field with a varying spatial distribution of infiltration properties can be predicted by transforming the unique connectivity function that was defined for a designated microtopography.     

A trans-world tidal gravity profile

Tidal recordings have been made with high-precision equipment at twenty-eight stations in the South East Asia and the South Pacific areas. Each station was occupied for five months or more. Amplitude factors (δ) and phase differences (α) of the principal tidal constituents exhibit a regional behaviour which results from the oceanic-tide interaction. At Alice Springs, Northern Territory, the middle point of Australia, the results based upon nine month's observations fit fairly well the Molodensky theory on the dynamical effects of the liquid core of the earth.     

Application of groundwater hydraulics to a basaltic water-table aquifer

Analysis of pump-test data of open wells in a basaltic water-table aquifer is made with methods based on both equilibrium and non-equilibrium formulae. The study has indicated that the Thiem's equilibrium formula and the ratio method of Narasimhan appear to be more suitable as compared with Jacob's and Chow's methods. Of the two, Narasimhan's ratio method, which does not require the graphical procedure, is more reliable than the Thiem's method since the latter involves an assumption of the value for the radius of influence. From the value of T (coefficient of transmissibility) obtained by Narasimhan's method it is also possible to calculate the value of the radius of influence by Thiem's method, which can be used in determining the required spacing between wells in the basaltic terrain in order to avoid mutual interference.     

On Evaluating Characteristics of the Solute Transport in the Arid Vadose Zone

The transport of bromide (Br) under matric heads of 0, ?2, ?5, and ?10 cm using undisturbed soil columns was investigated for understanding the solute transport in arid soils. Undisturbed soil cores were collected at ground surface, directly below where tension infiltrometer measurements were made in the Amargosa Desert, Nevada, United States. Laboratory experiments were conducted by introducing water containing Br tracer into a soil column maintained at steady‐state conditions. The observed data of breakthrough curves (BTC) were well fitted to an one‐region model, except for the cores at saturation, and a core at the matric head of ?5 cm, from which the observed data were better fitted to a two‐region model. Fitted pore water velocities with the one‐region model ranged from 1.2 to 56.6 cm/h, and fitted dispersion coefficients (D) ranged from 2.2 to 100 cm²/h. Results for the core analyzed with the two‐region model indicated that D ranged from 27.6 to 70.9 cm²/h at saturation, and 25.7 cm²/h at the matric head of ?5 cm; fraction of mobile water (β) ranged from 0.18 to 0.65, and mass transfer coefficient (ω) ranged from 0.006 to 0.03. In summary, the water fluxes and Br dispersion coefficients at investigated matric heads were very high due to the coarseness of the soils and possibly due to preferential flow pathways. These high water fluxes and Br dispersion coefficients would lead to a higher risk of deeper leaching accumulating nitrate nitrogen to the groundwater, and have significant effects on the desert ecosystem.     

An automated disc infiltrometer for infiltration rate measurements using a microflowmeter

This work presents a new design of disc infiltrometer, which, associated with a microflowmeter (MF) and a solenoid valve set, makes it possible to automate the infiltration rate (Q) measurements at different soil pressure heads (ψ). The MF consists of a 13·8‐cm long and 1·5 mm i.d. pipe, with a pressure transducer connecting the two ends of the MF, inserted in a water‐flow pipe that connects the Mariotte tube and the water‐supply reservoir of the disc infiltrometer. Water flow is calculated from the head losses in the MF. Changes in ψ in the bubble tower, automatically affected when the infiltration rate reaches steady state, are controlled by a datalogger connected to four solenoid valves. The new design was tested in laboratory and field conditions, and the results showed that the MF allows the soil water infiltration rates to be correctly estimated for different soil characteristics. The solenoid valve set plus datalogger system satisfactorily monitored the changes in ψ and allowed the measurement time to be optimized. Copyright © 2011 John Wiley & Sons, Ltd.