Storm Surges in New York During Hurricane Sandy in 2012: A Verification of the Wind-Stress Tide Relation

In October 2012 Hurricane Sandy devastated New York City and its vicinity caused mainly by the storm surge, which is the water height above normal astronomical tide level. The meteorological conditions were as follows: minimum central pressure, 962 hPa, highest sustained wind speed 27.1 m s $^{-1}$ ? 1 and maximum gust 37.8 m s $^{-1}$ ? 1 . The peak storm surge was at 3.9 m and the peak storm tide at 4.4 m (which is referenced above mean lower low water). The wind-stress tide relation shows that $S=K\,V^{2}$ S = K V 2 , where $S$ S is the storm surge, $V$ V is the wind speed and $K$ K is the coefficient. It is found that with $S$ S in units of m, and $V$ V in  m s $^{-1}$ ? 1 , $K = 0.0051$ K = 0.0051 with $R^{2}= 0.91$ R 2 = 0.91 ( $R$ R is the correlation coefficient) indicating that 91 % of the total variation of the storm surge can be explained by variations in the wind stress, which is proportional to $V^{2}$ V 2 . Similar results were obtained during Hurricane Irene in 2011, which also affected the New York area. Therefore, this simple wind stress-tide relation should be useful in coastal engineering, urban planning, and emergency management.     

Scalar Flux–Gradient Relationships Under Unstable Conditions over Water in Coastal Regions

The scalar flux–gradient relationships of temperature ( $\phi _{T}$ ? T ) and specific humidity ( $\phi _{q}$ ? q ) under unstable conditions are investigated using eddy-covariance measurements of air–sea turbulent fluxes and vertical profiles of temperature and specific humidity collected from a marine meteorological platform. The gradients of temperature and specific humidity are obtained from measurements at five heights above the sea surface using the log-square fitting method and the simpler first-order approximation method. The two methods yield similar results. The proposed flux–gradient relationships $\phi _{T}$ ? T and $\phi _{q}$ ? q covers a wide range of instability: the stability parameter $\zeta $ ζ ranges from $-$ ? 0.1 to $-$ ? 50. The functional form of the proposed flux–gradient relationships is an interpolation between the Businger–Dyer relation and the free convection relation, which includes the “ $-$ ? 1/2” and “ $-$ ? 1/3” scaling laws at two different stability regimes. The widely used COARE 3.0 algorithm, which is an interpolation between the integrals of the Businger–Dyer and the free convection relations, is also evaluated and compared. The analysis and comparisons show that both schemes generate reasonable values of $\phi _{q}$ ? q in the whole unstable regime. The COARE 3.0 algorithm, however, overestimates $\phi _{T}$ ? T values under very unstable conditions. The errors in the flux–gradient relationships induced by the random errors in the turbulence measurements are assessed. When the random errors are taken into account, the observations agree with predictions of various schemes fairly well, implying that the dominant transport mechanism is adequately captured by the Monin–Obukhov similarity theory. The study also shows that $\phi _{q}$ ? q is significantly ${>}\phi _{T}$ > ? T under unstable conditions and that the ratio $\phi _{q}/\phi _{T}$ ? q / ? T increases with $-\zeta $ ? ζ . The ratio of $\phi _{q}$ ? q to $\phi _{T}$ ? T and the ratio of turbulent transport efficiencies of heat and water vapour ( $R_{wT}/R_{wq}$ R wT / R wq ) suggest that heat is transported more efficiently than water vapour under unstable conditions.     

Characterization of Oscillatory Motions in the Stable Atmosphere of a Deep Valley

In a valley sheltered from strong synoptic effects, the dynamics of the valley atmosphere at night is dominated by katabatic winds. In a stably stratified atmosphere, these winds undergo temporal oscillations, whose frequency is given by $N \sin {\alpha }$ N sin α for an infinitely long slope of constant slope angle $\alpha $ α , $N$ N being the buoyancy frequency. Such an unsteady flow in a stably stratified atmosphere may also generate internal gravity waves (IGWs). The numerical study by Chemel et al. (Meteorol Atmos Phys 203:187–194, 2009) showed that, in the stable atmosphere of a deep valley, the oscillatory motions associated with the IGWs generated by katabatic winds are distinct from those of the katabatic winds. The IGW frequency was found to be independent of $\alpha $ α and about $0.8N$ 0.8 N . Their study did not consider the effects of the background stratification and valley geometry on these results. The present work extends this study by investigating those effects for a wide range of stratifications and slope angles, through numerical simulations for a deep valley. The two oscillatory systems are reproduced in the simulations. The frequency of the oscillations of the katabatic winds is found to be equal to $N$ N times the sine of the maximum slope angle. Remarkably, the IGW frequency is found to also vary as $C_\mathrm{w}N$ C w N , with $C_\mathrm{w}$ C w in the range $0.7$ 0.7 – $0.95$ 0.95 . These values for $C_\mathrm{w}$ C w are similar to those reported for IGWs radiated by any turbulent field with no dominant frequency component. Results suggest that the IGW wavelength is controlled by the valley depth.     

Vertical Distribution of Radiation and Energy Balance Partitioning Within and Above a Lodgepole Pine Stand Recovering from a Recent Insect Attack

The current outbreak of mountain pine beetle (MPB) that started in the late 1990s in British Columbia, Canada, is the largest ever recorded in the north American native habitat of the beetle. The killing of trees is expected to change the vertical distribution of net radiation ( $Q^*$ Q ? ) and the partitioning of latent ( $Q_\mathrm{E}$ Q E ) and sensible ( $Q_\mathrm{H}$ Q H ) heat fluxes in the different layers of an attacked forest canopy. During an intensive observation period in the summer of 2010, eddy-covariance flux and radiation measurements were made at seven heights from ground level up to 1.34 times the canopy height in an MPB-attacked open-canopy forest stand $(\hbox {leaf area index} = 0.55~\mathrm{{m}}^{2}\ \mathrm{{m}}^{-2})$ ( leaf area index = 0.55 m 2 m - 2 ) in the interior of British Columbia, Canada. The lodgepole pine dominated stand with a rich secondary structure (trees and understorey not killed by the beetle) was first attacked by the MPB in 2003 and received no management. In this study, the vertical distribution of the energy balance components and their sources and sinks were analyzed and energy balance closure (EBC) was determined for various levels within the canopy. The low stand density resulted in approximately 60 % of the shortwave irradiance and 50 % of the daily total $Q^*$ Q ? reaching the ground. Flux divergence calculations indicated relatively strong sources of latent heat at the ground and where the secondary structure was located. Only very weak sources of latent heat were found in the upper part of the canopy, which was mainly occupied by dead lodgepole pine trees. $Q_\mathrm{H}$ Q H was the dominant term throughout the canopy, and the Bowen ratio ( $Q_\mathrm{H}/Q_\mathrm{E}$ Q H / Q E ) increased with height in the canopy. Soil heat flux ( $Q_\mathrm{G}$ Q G ) accounted for approximately 4 % of $Q^*$ Q ? . Sensible heat storage in the air ( $\Delta Q_\mathrm{S,H}$ Δ Q S , H ) was the largest of the energy balance storage components in the upper canopy during daytime, while in the lower canopy sensible heat storage in the boles ( $\Delta Q_\mathrm{S,B}$ Δ Q S , B ) and biochemical energy storage ( $\Delta Q_\mathrm{S,C}$ Δ Q S , C ) were the largest terms. $\Delta Q_\mathrm{S,H}$ Δ Q S , H was almost constant from the bottom to above the canopy. $\Delta Q_\mathrm{S,C}$ Δ Q S , C , $\Delta Q_\mathrm{S,B}$ Δ Q S , B and latent heat storage in the air ( $\Delta Q_\mathrm{S,E}$ Δ Q S , E ) varied more than $\Delta Q_\mathrm{S,H}$ Δ Q S , H throughout the canopy. During daytime, energy balance closure was high in and above the upper canopy, and in the lowest canopy level. However, where the secondary structure was most abundant, ${\textit{EBC}} \le 66\,\%$ EBC ≤ 66 % . During nighttime, the storage terms together with $Q_\mathrm{G}$ Q G made up the largest part of the energy balance, while $Q_\mathrm{H}$ Q H and $Q_\mathrm{E}$ Q E were relatively small. These radiation and energy balance measurements in an insect-attacked forest highlight the role of secondary structure in the recovery of attacked stands.     

A New Sensitivity Analysis and Solution Method for Scintillometer Measurements of Area-Averaged Turbulent Fluxes

Scintillometer measurements of the turbulence inner-scale length $l_\mathrm{o }$ l o and refractive index structure function $C_n^2$ C n 2 allow for the retrieval of large-scale area-averaged turbulent fluxes in the atmospheric surface layer. This retrieval involves the solution of the non-linear set of equations defined by the Monin–Obukhov similarity hypothesis. A new method that uses an analytic solution to the set of equations is presented, which leads to a stable and efficient numerical method of computation that has the potential of eliminating computational error. Mathematical expressions are derived that map out the sensitivity of the turbulent flux measurements to uncertainties in source measurements such as $l_\mathrm{o }$ l o . These sensitivity functions differ from results in the previous literature; the reasons for the differences are explored.     

Surface Heterogeneity Effects on Regional-Scale Fluxes in the Stable Boundary Layer: Aerodynamic Roughness Length Transitions

The effects of abrupt streamwise transitions of the aerodynamic roughness length ( $z_\mathrm{o}$ z o ) on the stable atmospheric boundary layer are evaluated using a series of large-eddy simulations based on the first Global Energy and Water Cycle Experiment Atmospheric Boundary Layer intercomparison study (GABLS1). Four $z_\mathrm{o}$ z o values spanning three orders of magnitude are used to create all possible binary distributions with each arranged into patches of characteristic length scales equal to roughly one-half, one, and two times the equivalent homogeneous boundary-layer height. The impact of the heterogeneity on mean profiles of wind speed and temperature, on surface fluxes of heat and momentum, and on internal boundary-layer dynamics are considered. It is found that $z_\mathrm{o}$ z o transitions do not significantly alter the functional relationship between the average surface fluxes and the mean profiles of wind speed and potential temperature. Although this suggests that bulk similarity theory is applicable for modelling the stable boundary layer over $z_\mathrm{o}$ z o heterogeneity, effective surface parameters must still be specified. Existing models that solve for effective roughness lengths of momentum and heat are evaluated and compared to values derived from the simulation data. The existing models are unable to accurately reproduce both the values of the effective aerodynamic roughness lengths and their trends as functions of patch length scale and stability. A new model for the effective aerodynamic roughness length is developed to exploit the benefits of the other models tested. It accurately accounts for the effects of the heterogeneity and stratification on the blending height and effective aerodynamic roughness length. The new model provides improved average surface fluxes when used with bulk similarity.     

Transfer Coefficients of Momentum, Heat and Water Vapour in the Atmospheric Surface Layer of a Large Freshwater Lake

In studies of lake–atmosphere interactions, the fluxes of momentum, water vapour and sensible heat are often parametrized as being proportional to the differences in wind, humidity and air temperature between the water surface and a reference height above the surface. Here, the proportionality via transfer coefficients in these relationships was investigated with the eddy-covariance method at three sites within an eddy-covariance mesonet across Lake Taihu, China. The results indicate that the transfer coefficients decreased with increasing wind speed for weak winds and approached constant values for strong winds. The presence of submerged macrophytes reduced the momentum transfer (drag) coefficient significantly. At the two sites free of submerged macrophytes, the 10-m drag coefficients under neutral stability were 1.8 $(\pm \,0.4) \times \,10^{-3}$ ( ± 0.4 ) × 10 ? 3 and $1.7\,(\pm \,0.3) \times \,10^{-3 }$ 1.7 ( ± 0.3 ) × 10 ? 3 at the wind speed of $9\,\text{ m } \text{ s }^{-1}$ 9 m s ? 1 , which are 38 and 34 % greater than the prediction by the Garratt model for the marine environment.     

Investigation of the Stable Atmospheric Boundary Layer at Halley Antarctica

Boundary-layer measurements from the Brunt Ice Shelf, Antarctica are analyzed to determine flux–profile relationships. Dimensionless quantities are derived in the standard approach from estimates of wind shear, potential temperature gradient, Richardson number, eddy diffusivities for momentum and heat, Prandtl number, mixing length and turbulent kinetic energy. Nieuwstadt local scaling theory for the stable atmospheric boundary-layer appears to work well departing only slightly from expressions found in mid-latitudes. An $E$ E – $l_{\mathrm{m}}$ l m single-column model of the stable boundary layer is implemented based on local scaling arguments. Simulations based on the first GEWEX Atmospheric Boundary-Layer Study case study are validated against ensemble-averaged profiles for various stability classes. A stability-dependent function of the dimensionless turbulent kinetic energy allows a better fit to the ensemble profiles.     

Improving a Two-Equation Turbulence Model for Canopy Flows Using Large-Eddy Simulation

Large-eddy simulations of the neutrally-stratified flow over an extended homogeneous forest were used to calibrate a canopy model for the Reynolds-averaged Navier–Stokes (RaNS) method with the $k-\varepsilon $ k - ε turbulence model. It was found that, when modelling the forest as a porous medium, the canopy drag dissipates the turbulent kinetic energy (acts as a sink term). The proposed model was then tested in more complex flows: a finite length forest and a forested hill. In the finite length forest, the destruction of the turbulent kinetic energy by the canopy was overestimated near the edge, for a length approximately twice the tree height. In the forested hill, the model was less accurate inside the recirculation zone and overestimated the turbulent kinetic energy, due to an incorrect prediction of the production term. Nevertheless, the canopy model presented here provided consistent results in both a priori and a posteriori tests and improved the accuracy of RaNS simulations with the $k-\varepsilon $ k - ε model.     

Air–Sea \mathrm{CO}_{2} Gas Transfer Velocity in a Shallow Estuary

The air–sea transfer velocity of $\mathrm{CO}_{2}\, (k_{\mathrm{CO}_{2}})$ was investigated in a shallow estuary in March to July 2012, using eddy-covariance measurements of $\mathrm{CO}_{2}$ fluxes and measured air–sea $\mathrm{CO}_{2}$ partial-pressure differences. A data evaluation method that eliminates data by nine rejection criteria in order to heighten parametrization certainty is proposed. We tested the data evaluation method by comparing two datasets: one derived using quality criteria related solely to the eddy-covariance method, and the other derived using quality criteria based on both eddy-covariance and cospectral peak methods. The best parametrization of transfer velocity normalized to a Schmidt number of 600 $(k_{600})$ was determined to be: $k_{600} = 0.3\,{U_{10}}^{2.5}$ where $U_{10}$ is the wind speed in m $\mathrm{s}^{-1}$ at 10 m; $k_{600}$ is based on $\mathrm{CO}_{2}$ fluxes calculated by the eddy-covariance method and including the cospectral peak method criteria. At low wind speeds, the transfer velocity in the shallow water estuary was lower than in other coastal waters, possibly a symptom of low tidal amplitude leading to low intensity water turbulence. High transfer velocities were recorded above wind speeds of 5 m $\mathrm{s}^{-1}$ , believed to be caused by early-breaking waves and the large fetch (6.5 km) of the estuary. These findings indicate that turbulence in both air and water influences the transfer velocity.     

Investigation of the Flow Structure in Step-Up Street Canyons—Mean Flow and Turbulence Statistics

A step-up street canyon is a characteristic urban element composed of two buildings in which the height of the upwind building ( $H_\mathrm{u}$ ) is less than the height of the downwind building ( $H_\mathrm{d}$ ). Here, the effect of canyon geometry on the flow structure in isolated step-up street canyons is investigated through isothermal wind-tunnel measurements. The measurements were acquired along the vertical symmetry plane of model buildings using two-dimensional particle image velocimetry (PIV) for normal approach flow. The building-height ratios considered were: $H_\mathrm{d}/ H_\mathrm{u} \approx 3$ , and $H_\mathrm{d}/ H_\mathrm{u} \approx 1.67$ . For each building-height ratio, the along-wind lengths (L) of the upwind and downwind buildings, and the street-canyon width (S) were kept constant, with $L \approx S$ . The cross-wind widths (W) of the upwind and downwind buildings were varied uniformly from $W/S \approx 1$ through $W/S \approx 4$ , in increments of $W/S \approx 1$ . The objective of the work was to characterize the changes in the flow structure in step-up canyons as a function of W/S, for fixed L, S, and $H_\mathrm{d}/H_\mathrm{u}$ values. The results indicate that the in-canyon flow structure does not vary significantly for $H_\mathrm{d}/H_\mathrm{u} \approx 3$ for the W/S values considered. Qualitatively, for $H_\mathrm{d}/H_\mathrm{u} \approx 3$ , the upwind building behaves as an obstacle in the upwind cavity of the downwind building. In contrast, the flow patterns observed for the $H_\mathrm{d}/H_\mathrm{u} \approx 1.67$ configurations are unique and counter-intuitive, and depend strongly on building width (W/S). For $W/S \approx 1$ and $W/S \approx 2$ , the effect of lateral flow into the canyon is so prominent that even the mean flow patterns are highly ambiguous. For $W/S \approx 3$ and 4, the flow along the vertical symmetry plane is more shielded from the lateral flow, and hence a stable counter-rotating vortex pair is observed in the canyon. In addition to these qualitative features, a quantitative analysis of the mean flow field and turbulence stress field is presented.     

Impact of Megacity Shanghai on the Urban Heat-Island Effects over the Downstream City Kunshan

The impact of upstream urbanization on the enhanced urban heat-island (UHI) effects between Shanghai and Kunshan is investigated by analyzing seven years of surface observations and results from mesoscale model simulations. The observational analysis indicates that, under easterly and westerly winds, the temperature difference between Shanghai and Kunshan increases with wind speed when the wind speed \(<\) 5 m s \(^{-1}\) . The Weather Research and Forecasting (WRF) numerical model, coupled with a one-layer urban canopy model (UCM), is used to examine the UHI structure and upstream effects by replacing the urban surface of Shanghai and/or Kunshan with cropland. The WRF/UCM modelling system is capable of reproducing the surface temperature and wind field reasonably well. The simulated urban canopy wind speed is a better representation of the near-surface wind speed than is the 10-m wind speed at the centre of Shanghai. Without the urban landscape of Shanghai, the surface air temperature over downstream Kunshan would decrease by 0.2–0.4  \(^{\circ }\) C in the afternoon and 0.4–0.6  \(^{\circ }\) C in the evening. In the simulation with the urban landscape of Shanghai, a shallow cold layer is found above the UHI, with a minimum temperature of about \(-0.2\) to \(-\) 0.5  \(^{\circ }\) C during the afternoon hours. Strong horizontal divergence is found in this cold layer. The easterly breeze over Shanghai is strengthened at the surface by strong UHI effects, but weakened at upper levels. With the appearance of the urban landscape specific humidity decreases by 0.5–1 g kg \(^{-1}\) within the urban area because of the waterproof property of an urban surface. On the other hand, the upper-level specific humidity is increased because of water vapour transferred by the strong upward vertical motions.     

Bulk Mixing and Decoupling of the Nocturnal Stable Boundary Layer Characterized Using a Ubiquitous Natural Tracer

Vertical mixing of the nocturnal stable boundary layer (SBL) over a complex land surface is investigated for a range of stabilities, using a decoupling index ( $0 < D_{rb} < 1$ ) based on the 2–50 m bulk gradient of the ubiquitous natural trace gas radon-222. The relationship between $D_{rb}$ and the bulk Richardson number ( $R_{ib}$ ) exhibits three broad regions: (1) a well-mixed region ( $D_{rb} \approx 0.05$ ) in weakly stable conditions ( $R_{ib} < 0.03$ ); (2) a steeply increasing region ( $0.05 < D_{rb} < 0.9$ ) for “transitional” stabilities ( $0.03 < R_{ib} < 1$ ); and (3) a decoupled region ( $D_{rb} \approx 0.9$ –1.0) in very stable conditions ( $R_{ib} > 1$ ). $D_{rb}$ exhibits a large variability within individual $R_{ib}$ bins, however, due to a range of competing processes influencing bulk mixing under different conditions. To explore these processes in $R_{ib}$ – $D_{rb}$ space, we perform a bivariate analysis of the bulk thermodynamic gradients, various indicators of external influences, and key turbulence quantities at 10 and 50 m. Strong and consistent patterns are found, and five distinct regions in $R_{ib}$ – $D_{rb}$ space are identified and associated with archetypal stable boundary-layer regimes. Results demonstrate that the introduction of a scalar decoupling index yields valuable information about turbulent mixing in the SBL that cannot be gained directly from a single bulk thermodynamic stability parameter. A significant part of the high variability observed in turbulence statistics during very stable conditions is attributable to changes in the degree of decoupling of the SBL from the residual layer above. When examined in $R_{ib}$ – $D_{rb}$ space, it is seen that very different turbulence regimes can occur for the same value of $R_{ib}$ , depending on the particular combination of values for the bulk temperature gradient and wind shear, together with external factors. Extremely low turbulent variances and fluxes are found at 50 m height when $R_{ib} > 1$ and $D_{rb} \approx 1$ (fully decoupled). These “quiescent” cases tend to occur when geostrophic forcing is very weak and subsidence is present, but are not associated with the largest bulk temperature gradients. Humidity and net radiation data indicate the presence of low cloud, patchy fog or dew, any of which may aid decoupling in these cases by preventing temperature gradients from increasing sufficiently to favour gravity wave activity. The largest temperature gradients in our dataset are actually associated with smaller values of the decoupling index ( $D_{rb} < 0.7$ ), indicating the presence of mixing. Strong evidence is seen from enhanced turbulence levels, fluxes and submeso activity at 50 m, as well as high temperature variances and heat flux intermittencies at 10 m, suggesting this region of the $R_{ib}$ – $D_{rb}$ distribution can be identified as a top-down mixing regime. This may indicate an important role for gravity waves and other wave-like phenomena in providing the energy required for sporadic mixing at this complex terrain site.     

On the Mechanism of Air Pollutant Removal in Two-Dimensional Idealized Street Canyons: A Large-Eddy Simulation Approach

Flow resistance, ventilation, and pollutant removal for idealized two-dimensional (2D) street canyons of different building-height to street-width (aspect) ratios $AR$ are examined using the friction factor $f$ , air exchange rate (ACH), and pollutant exchange rate (PCH), respectively, calculated by large-eddy simulation (LES). The flows are basically classified into three characteristic regimes, namely isolated roughness, wake interference, and skimming flow, as functions of the aspect ratios. The LES results are validated by various experimental and numerical datasets available in the literature. The friction factor increases with decreasing aspect ratio and reaches a peak at $AR = 0.1$ in the isolated roughness regime and decreases thereafter. As with the friction factor, the ACH increases with decreasing aspect ratio in the wake interference and skimming flow regimes, signifying the improved aged air removal for a wider street canyon. The PCH exhibits a behaviour different from its ACH counterpart in the range of aspect ratios tested. Pollutants are most effectively removed from the street canyon with $AR = 0.5$ . However, a minimum of PCH is found nearby at $AR = 0.3$ , at which the pollutant removal is sharply weakened. Besides, the ACH and PCH are partitioned into the mean and turbulent components to compare their relative contributions. In line with our earlier Reynolds-averaged Navier–Stokes calculations (Liu et al., Atmos Environ 45:4763–4769, 2011), the current LES shows that the turbulent components contribute more to both ACH and PCH, consistently demonstrating the importance of atmospheric turbulence in the ventilation and pollutant removal for urban areas.     

Large-Eddy Simulation of Heat Transfer from a Single Cube Mounted on a Very Rough Wall

The local thermal effects in the wake of a single cube with a strong heated rear face, representing a large building in an urban area, are studied using large-eddy simulations (LES) for various degrees of heating, which are characterized by the local Richardson number, $Ri$ . New wall models are implemented for momentum and temperature and comparison of the flow and thermal fields with the wind-tunnel data of Richards et al. (J Wind Eng Ind Aerodyn 94, 621–636, 2006) shows fair agreement. Buoyancy effects are quite evident at low $Ri$ and a significant increase in the turbulence levels is observed for such flows. Apart from the comparisons with experiments, further analysis included the estimation of the thermal boundary-layer thickness and heat transfer coefficient for all $Ri$ . For sufficiently strong heating, the heat transfer coefficient at the leeward face is found to be higher than the roof surface. This suggests that, beyond a certain $Ri$ value, buoyancy forces from the former surface dominate the strong streamwise convection of the latter. Quadrant analysis along the shear layer behind the cube showed that the strength of sweeps that contribute to momentum flux is considerably enhanced by heating. The contribution of different quadrants to the heat flux is found to be very different to that of the momentum flux for lower $Ri$ .     

A Semi-Analytical Approach for Parametrization of the Obukhov Stability Parameter in the Unstable Atmospheric Surface Layer

A semi-analytical scheme is proposed to parametrize the Obukhov stability parameter \(\zeta \) (= \(z/L\) ; \(z\) is the height above the ground and \(L\) is the Obukhov length) in terms of the bulk Richardson number ( \(R_{iB}\) ) in unstable conditions within the framework of Monin–Obukhov similarity (MOS) theory. The scheme involves, (i) a solution of a cubic equation in \(\zeta \) whose coefficients depend on the gradient Richardson number ( \(R_{i}\) ), and (ii) a relationship between \(R_{i}\) and \(R_{iB}\) . The proposed scheme is applicable for a wide range (i) \(-5\le R_{iB}\le 0\) , (ii) \(0\le \hbox {ln}(z_{0}/z_{h})\le 29.0\) , and (iii) \(10\le z/z_{0}\le 10^{5}\) and performs relatively better than all other schemes in terms of accuracy in computation of surface-layer transfer coefficients. The absolute errors in computing the transfer coefficients do not exceed 7 %. The analysis presented here is found to be valid for different \(\gamma _{m}\) and \(\gamma _{h}\) appearing in the expressions of the similarity functions \(\varphi _{m}\) and \(\varphi _{h}\) (representing non-dimensional wind and temperature profiles), so long as the ratio of \(\gamma _{m}\) to \(\gamma _{h} \ge 1\) . The improved scheme can be easily employed in atmospheric modelling for a comprehensive range of \(R_{iB}\) and a variety of surfaces.     

Intercomparison of Methods for the Simultaneous Estimation of Zero-Plane Displacement and Aerodynamic Roughness Length from Single-Level Eddy-Covariance Data

We applied three approaches to estimate the zero-plane displacement $d$ through the aerodynamic measurement height $z$ (with $z = z_{m}- d$ and $z_{m}$ being the measurement height above the surface), and the aerodynamic roughness length $z_{0}$ , from single-level eddy covariance data. Two approaches (one iterative and one regression-based) were based on the universal function in the logarithmic wind profile and yielded an inherently simultaneous estimation of both $d$ and $z_{0}$ . The third approach was based on flux–variance similarity, where estimation of $d$ and consecutive estimation of $z_{0}$ are independent steps. Each approach was further divided into two methods differing either with respect to the solution technique (profile approaches) or with respect to the variable (variance of vertical wind and temperature, respectively). All methods were applied to measurements above a large, growing wheat field where a uniform canopy height and its frequent monitoring provided plausibility limits for the resulting estimates of time-variant $d$ and $z_{0}$ . After applying, for each approach, a specific data filtering that accounted for the range of conditions (e.g. stability) for which it is valid, five of the six methods were able to describe the temporal changes of roughness parameters associated with crop growth and harvest, and four of them agreed on $d$ to within 0.3 m most of the time. Application of the same methods to measurements with a more heterogeneous footprint consisting of fully-grown sugarbeet and a varying contribution of adjacent harvested fields exhibited a plausible dependence of the roughness parameters on the sugarbeet fraction. It also revealed that the methods producing the largest outliers can differ between site conditions and stability. We therefore conclude that when determining $d$ for canopies with unknown properties from single-level measurements, as is increasingly done, it is important to compare the results of a number of methods rather than rely on a single one. An ensemble average or median of the results, possibly after elimination of methods that produce outliers, can help to yield more robust estimates. The estimates of $z_{0}$ were almost exclusively physically plausible, although $d$ was considered unknown and estimated simultaneously with the methods and results described above.     

Observing Entrainment Processes Using a Small Unmanned Aerial Vehicle: A Feasibility Study

Measurement flights with the meteorological mini aerial vehicle (M $^2$ AV) were performed in spring 2011 to assess the capability of an unmanned aerial vehicle (UAV) to measure the structure of the transition zone between the convective boundary layer and the stably stratified free atmosphere. The campaign took place at the Meteorological Observatory Lindenberg/Richard-Aßmann-Observatory of the German Meteorological Service. Besides the M $^2$ AV flights, observations were made from a 12-m and a 99-m tower, a sodar, two ceilometers, radiosondes, and a tethered balloon with sensor packages at six different levels. M $^2$ AV measurements were intentionally combined with remote sensing systems. The height range of the entrainment zone as well as its diurnal cycle were provided by the remote sensing instruments. The UAV provided the high-resolution in situ data of temperature and wind for the study of turbulent processes. It is shown that the M $^2$ AV is able to maintain constant altitude with very small deviations—a pre-requisite to study processes inside the often quite thin entrainment zone and that M $^2$ AV high-resolution wind and temperature measurements allow for very detailed studies of the fine structure of the atmosphere and thus for the identification of quite local and/or short-duration processes such as overshooting thermals or downward intrusions of warm air. Spatial series measured by the M $^2$ AV during horizontal flights show turbulent exchange of heat in short turbulent bursts at heights close to and within the entrainment zone. Scaled vertical profiles of vertical velocity, potential temperature variance, and sensible heat flux confirm the general shape found by previous measurements and numerical studies.     

Some Statistics of the Temperature Structure Parameter in the Convective Boundary Layer Observed by Sodar

The characteristics of the temporal and height variations of the temperature structure parameter $C_\mathrm{T}^{2}$ in strongly convective situations derived from the sodar echo-signal intensity measurements were analyzed for the first 100 m. It was corroborated that the probability density function (pdf) of the logarithm of $C_\mathrm{T}^{2}$ in the lower convective boundary layer is markedly non-Gaussian, whereas turbulence theory predicts it to be normal. It was also corroborated that the sum of two weighted Gaussians, which characterize the statistics of $C_\mathrm{T}^{2}$ within convective plumes and in their environment and the probability of plume occurrence, well approximates the observed pdfs. It was shown that the height behaviour of the arithmetic mean of $ C_\mathrm{T}^{2}$ (both total and within plumes) follows well a power law $C_\mathrm{T}^{2} (z) \sim z^{-q}$ with the exponent $q$ close to the theoretically predicted value of 4/3. But for the geometrical means of $C_\mathrm{T}^{2}$ (both total and within the plumes), $q$ is close to 1. The difference between arithmetically and geometrically averaged $C_\mathrm{T}^{2}$ profiles was analyzed. The vertical profiles of the standard deviation, skewness and kurtosis of $\hbox {ln}C_\mathrm{T}^{2}$ pdfs were analyzed to show their steady behaviour with height. The standard deviations of the logarithm of $C_\mathrm{T}^{2}$ within the plumes and between them are similar and are 1.5 times less than the total standard deviation. The estimate of the variability index $F_\mathrm{T}$ and its height behaviour were obtained, which can be useful to validate some theoretical and modelling predictions. The vertical profiles of the skewness and kurtosis show the negative asymmetry of pdfs and their flatness, respectively. The spectra of variations in $\hbox {ln}C_\mathrm{T}^{2}$ are shown to be satisfactorily fitted by the power law $f^{-\gamma } $ in the frequency range 0.02 and 0.2 Hz, with the average exponent $\approx $ 1.27  $\pm $  0.22.