混凝土芯砂石桩的单桩承载力时间效应分析

在饱和软黏土地基沉桩过程中,挤土桩桩周土体将遭受相当大的挤压应力并引起很高的超静孔隙水压力,桩周土体超静孔隙水压力的消散,使桩周土体有效应力相应地增长,单桩承载力在间歇期内也会随着时间而逐渐增加。基于挤土桩沉桩过程所产生的挤土效应,运用圆孔扩张理论和固结理论分析了新型软基处理技术-混凝土芯砂石桩的挤土性状,并与软基处理中常用的CFG桩作了比较,从单桩侧摩阻力的时间效应方面分析了混凝土芯砂石桩的优越性。     

粉土与粉质黏土互层中静压桩桩土界面孔隙水压力

为研究层状黏性土在静压桩沉桩过程中桩土界面孔隙水压力的分布规律,依托山东东营某桩基工程开展了现场足尺静压桩试验,分析了桩土界面孔隙水压力的变化规律,探讨了桩土界面超孔隙水压力的分布特征,明确了桩土界面孔隙水压力和超孔隙水压力的消散特性,并结合水力压裂理论和孔穴扩张理论,揭示了沉桩过程中桩土界面沿桩长方向超孔隙水压力的分布形式。试验结果表明：孔隙水压力、超孔隙水压力与土层性质密切相关,二者均在粉土层中增长较慢,在粉质黏土层中增长较快;在同一深度处,两者均存在明显的消散现象,在粉土中的消散程度明显大于粉质黏土中;采用水力压裂理论结合孔穴扩张理论计算的超孔隙水压力沿桩长方向的变化规律与试验值相吻合;桩身贯入深度越大,超孔隙水压力理论计算值与现场实测值越接近。     

沉桩超孔隙水压力对码头边坡稳定的影响

沉桩会对码头边坡稳定产生不利影响,一是引起桩周土体超孔隙水压力的急剧上升,导致土体有效应力降低;二是沉桩的振动加速度会产生对边坡稳定不利的瞬时惯性力。对于灵敏度低的土质岸坡来说,前者是影响其稳定性的主要因素。考虑沉桩时初始超孔隙水压力的分布,根据Biot固结方程超孔隙水压力消散解的一般表达式,建立了沉桩引起的超孔隙水压力随时间消散的解析式,在条分法的基础上考虑沉桩产生的超孔隙水压力的不利影响,建立了沉桩时边坡稳定安全系数的计算公式。根据沉桩顺序对某码头进行边坡稳定分析,结果表明：考虑打桩作用的岸坡稳定安全系数明显降低,沉桩产生的超孔隙水压力逐渐消散,边坡稳定安全系数随沉桩工序历时变化,施工中期由于超孔隙水压力叠加,岸坡最危险,沉桩结束3个月以后,超孔隙水压力基本消散,边坡稳定安全系数接近不考虑沉桩时的值。工程中要根据打桩计划进行边坡稳定计算。     

饱和软土中沉桩引起的孔隙水压力估算

饱和软土中挤土桩的承载力随时间的增长与沉桩引起的超孔隙水压力大小及其消散有密切关系。分析了小孔扩张理论的不足，提出用土压力理论来估算沉桩引起的超孔隙水压力。分别讨论了单桩和群桩两种情况下超孔隙水压力的计算，并与实测资料进行了对比。     

沉桩引起的三维超静孔隙水压力计算及其应用

引入时间、深度参数分析在饱和软粘土中沉桩时引起的超静孔隙水压力,给出了考虑固结效应的超静孔隙水压力的三维解析解;分析了超静孔隙水压力的消散过程中桩周土发生曼德尔效应的时间和区域,提出了在群桩施工过程中土体中的超静孔隙水压力是消散与累加的综合过程,施工完毕后则变为单一的消散的计算模型,并给出计算公式。通过算例,分析了桩群不同桩距、不同入桩顺序对超静孔隙水压力的影响。     

沉桩挤土对孔隙水压力影响的试验研究

软粘土层深厚的地区进行预制桩沉桩将产生超静孔隙水压力的累积,过高的超静孔隙水压力使周围土体及建筑、地下管线等产生较大的变位,甚至产生破坏。以一次沉桩引起的超静孔隙水压力的原型试验,表明,单桩沉桩显著影响范围可达15m,沉桩引起的超静孔隙水压力水平可以达到甚至超过上覆有效土压力,并出现两个不同的相对稳定水平阶段。     

有明黏土中搅拌桩施工时的孔隙水压力

深层搅拌桩施工时,固化剂的注入与叶片的搅拌作用不可避免地会扰动周围土体,改变桩周土体中的应力状态,产生超静孔隙水压力。在高灵敏性的日本有明黏土中搅拌桩施工时对周围土体中的孔隙水压力进行了现场监测。监测结果表明周围土体中产生了很高的超静孔隙水压力,其量值较土体的初始上覆压力还要大,使土体中的有效应力为零,处于张拉状态,但是该超静孔隙水压力在初始阶段消散得非常快。为分析施工引起的超静孔隙水压力,将搅拌桩施工时和周围土体的相互作用采用受剪的孔穴扩张过程来模拟,提出一种简单的方法来计算搅拌桩施工时周围土体中的超静孔隙水压力,同时考虑了固化剂注入时的膨胀压力与旋转叶片在搅拌时所产生的剪切力的作用。超静孔隙水压力由土的不排水抗剪强度、剪切力、注浆压力和孔隙压力系数所确定。所提出的计算方法得到实测数据的验证。     

软土地基中单桩施工引起的超孔隙水压力

通过对桩基施工过程中实测资料的分析，探讨了沉桩时单桩周围土中产生的超孔隙水压力的大小、分布及影响范围，并与理论解进行了对比。还对桩-土界面处的超孔隙水压力进行了讨论。     

饱和土体小孔扩张问题的弹塑性解析解

将土体在圆孔扩张过程中的应力分布分为三个区域，基于修正剑桥模型，推导了圆孔扩张过程中土体在三个区域的超孔隙水压力的解析表达式，对比分析了固结比对土体中应力分布的影响。分析推导可为沉桩、旁压试验、静力触探等岩土工程问题提供理论依据。     

饱和黏土中静压沉桩模型试验及数值模拟研究

通过饱和黏土中静压沉桩模型试验,模拟了预制混凝土桩的施工过程,重点监测了孔隙水压力、桩侧土压力、地面隆起量随桩的贯入深度和距桩轴不同距离的变化规律。结果表明:在沉桩过程中,测点处超孔隙水压力的最大值发生在桩端到达该点上方约0.8 d处(d为桩的直径);距桩轴相同距离处,离桩端越近,挤土压力越大;每一级沉桩时地面隆起总量呈指数递减。采用ABAQUS软件对沉桩过程进行数值模拟,并与模型试验结果进行对比。     

考虑软土结构性损伤的柱形孔扩张理论分析

采用考虑结构性损伤的四折线应变软化模型,针对管桩沉桩过程中产生的挤土效应,得出改进的柱形孔扩张理论解,并与已有模型进行对比分析,结果表明,简化的四折线模型与软土的典型压缩曲线最为接近,提出了四折线模型中各直线段和相应参数的确定方法。采用Mohr-Coulomb屈服准则和相关联流动法则,提出了桩周不同区域内土体的应力、应变计算公式,给出了极限软化半径、极限破坏半径和极限扩张压力的计算方法。结合工程实例,通过对比分析发现,四折线模型的位移计算值与实测值最为接近,能更好地符合管桩挤土效应的实际情况。     

基于广义SMP准则及应力路径法的柱孔扩张分析

柱孔扩张理论广泛用于旁压试验机制分析、沉桩挤土效应等岩土工程问题中。基于经典的Vesic孔扩张理论,采用能够考虑中主应力效应的广义SMP屈服准则,并结合有限应变理论对均质土体中柱孔扩张问题进行分析,根据应力路径假设提出确定塑性区平均体应变的解析步骤。通过大量变参数计算给出具有不同刚度指标 、泊松比 和内摩擦角 的土中柱孔扩张极限状态下的塑性区平均体应变、孔扩张半径比和孔扩张系数。分析结果表明, 、 、 越大,塑性区平均体应变越小,塑性区半径比越大,孔扩张系数越大;随着 增加, 的变化对孔扩张系数的影响更显著。同时,将结果与基于Mohr-Coulomb准则的孔扩张解答进行比较,探讨不同土性参数时中主应力效应对孔扩张系数的影响。文中分析方法及给出的考虑中主应力效应的柱孔扩张系数表可为原位试验分析及桩侧摩阻力估算提供参考。     

基于广义SMP破坏准则的柱形孔扩张问题理论分析

采用应力跌落的简化应力-应变模型考虑土的应变软化特性,同时采用简化的体积应变?v与大主应变?1及大主应变?1与小主应变?3之间的相互关系反映土的剪胀特性,根据空间准滑动面(SMP)理论和平面应变轴对称问题的柱形孔扩张基本方程,推导并给出一般黏性土中柱形孔扩张问题的应力场、应变场、位移场、塑性区半径和孔扩张压力。通过算例分析,探讨了土的剪胀因素、软化特性对孔扩张问题的影响程度。为了反映中主应力的影响,将本文解与基于Mohr-Coulomb破坏准则的解答进行了比较。计算结果表明,土的剪胀性和软化特性及中主应力对孔扩张问题的影响是显著的,基于Mohr－Coulomb破坏准则的孔扩张解答往往偏于保守。     

各向异性初始应力状态下圆柱孔扩张理论弹塑性分析

传统的圆柱孔扩张理论假定初始应力为各向同性的。在城市地下管道的铺设、隧道工程等的水平掘进施工过程中,圆柱孔受到的初始竖向应力不等于初始水平应力,并不满足各向同性初始应力条件。考虑土体的各向异性初始应力条件,假定土体满足Mohr-Coulomb屈服准则,推导了各向异性初始应力状态下的圆柱孔扩张问题弹塑性解答。算例计算结果表明：土性参数一定时,在相同内压力作用下,各向异性初始应力状态下的圆柱孔扩张形成的塑性区半径大于各向同性初始应力状态下的圆柱孔扩张的塑性区半径,但前者的极限扩孔压力小于后者。     

Elastic‐plastic solutions for expanding cavities embedded in two different cohesive‐frictional materials

An analytical solution of cavity expansion in two different concentric regions of soil is developed and investigated in this paper. The cavity is embedded within a soil with finite radial dimension and surrounded by a second soil, which extends to infinity. Large‐strain quasi‐static expansion of both spherical and cylindrical cavities in elastic‐plastic soils is considered. A non‐associated Mohr–Coulomb yield criterion is used for both soils. Closed‐form solutions are derived, which provide the stress and strain fields during the expansion of the cavity from an initial to a final radius. The analytical solution is validated against finite element simulations, and the effect of varying geometric and material parameters is studied. The influence of the two different soils during cavity expansion is discussed by using pressure–expansion curves and by studying the development of plastic regions within the soils. The analytical method may be applied to various geotechnical problems, which involve aspects of soil layering, such as cone penetration test interpretation, ground‐freezing around shafts, tunnelling, and mining. © 2014 The Authors. International Journal for Numerical and Analytical Methods in Geomechanics published by John Wiley & Sons Ltd.     

Undrained expansion of a cylindrical cavity in clays with fabric anisotropy: theoretical solution

This paper presents a novel, exact, semi-analytical solution for the quasi-static undrained expansion of a cylindrical cavity in soft soils with fabric anisotropy. This is the first theoretical solution of the undrained expansion of a cylindrical cavity under plane strain conditions for soft soils with anisotropic behaviour of plastic nature. The solution is rigorously developed in detail, introducing a new stress invariant to deal with the soil fabric. The semi-analytical solution requires numerical evaluation of a system of six first-order ordinary differential equations. The results agree with finite element analyses and show the influence of anisotropic plastic behaviour. The effective stresses at critical state are constant, and they may be analytically related to the undrained shear strength. The initial vertical cross-anisotropy caused by soil deposition changes towards a radial cross-anisotropy after cavity expansion. The analysis of the stress paths shows that proper modelling of anisotropic plastic behaviour involves modelling not only the initial fabric anisotropy but also its evolution with plastic straining.     

上海地区某高层建筑基坑开挖和沉桩环境效应浅析

该文就软土地区高层建筑基础工程施工中,基坑开挖和沉桩挤土产生的环境效应进行了简析,结合工程实例提出了相应的对策。     

非轴对称位移边界下球孔扩张挤土位移弹性解答

以现有半无限土体中球孔扩张挤土位移的解答为基础,分别对水平地表和非轴对称斜边两个位移边界进行应力修正,运用坐标转换法和叠加法的原理,改进现有的分析方法,得到较为简化的非轴对称位移边界下扩孔问题的解答,并对非轴对称斜边倾角以及球孔离斜边距离等因素对挤土位移的影响进行了分析。结果表明：倾斜边界条件的存在对球孔两侧的挤土位移有明显影响,且随着非轴对称边界倾角的增大,靠近倾斜边界侧的挤土位移也随之增大;球孔距自由边界的距离越大,自由边界对挤土位移的影响也越小。该解答对非轴对称边界条件下的静压沉桩以及相关扩孔问题的设计和施工具有一定的指导意义和实用价值。     

Stress and pore pressure changes in clay during and after the expansion of a cylindrical cavity

The disturbance of a clay mass, due to either the installation of a driven pile or the expansion of a pressuremeter membrane, is often modelled as a cylindrical cavity expansion. In addition, it is usual (and convenient) to assume that the expansion occurs under conditions of plane strain. For this problem a method of analysis is presented which considers the soil to be a saturated two-phase material with a pore fluid which flows according to Darcy's Law. Non-linearity in material behaviour is permitted as long as the effective stress–strain law can be written in an incremental or rate form. The use of a consolidation analysis allows the changes in effective stress and pore pressure to be determined at any stage during both the cavity expansion and the subsequent period of reconsolidation. Expansions may occur at any prescribed rate, including the very fast (undrained) and the very slow (fully drained) case. The technique is illustrated by considering the expansion of a cavity in two different types of elastoplastic soil. It is shown how these solutions may be used to model the disturbance of the soil due to pile driving.     

XCC pile installation effect in soft soil ground: A simplified analytical model

This paper presents a simplified analytical model: the X-shaped cylindrical cavity expansion method (XCEM), which can be used to interpret and predict the displacement, stress, and excess pore pressure caused by the X-section cast in place concrete (XCC) pile installation in soft soil. Analytical solutions for the displacement and strain field are obtained with a streamlined solution, base on the strain path method (SPM). The stress and excess pore pressure can then be subsequently determined with the assumption of the elastic-perfectly plastic soil behavior. A positive agreement was found when the theoretical prediction of the displacement, stress, and excess pores pressure was compared against the field measurements. The proposed XCEM improves the conventional cavity expansion method (CEM) and offers a framework for understanding the non-circular cross-section penetrator problem, which is different from the conventional circular penetrator problem.