利用MP提高GPS单点定位精度的研究

多路径误差是GPS定位重要的误差源之一,本文利用MP(多径组合观测值)对观测值受到的多路径效应进行定量评价,在GPS伪距单点定位中降低受多路径效应影响的观测值的权重,达到削减多路径误差提高定位精度的目的,最后通过试验验证了此方法的有效性和可靠性。     

GPS变形监测中多路径效应的削弱方法研究

主要从GPS的基本观测方程出发,通过数学分析的方法,在GPS观测值之间建立数学模型,进一步分别推导了伪距观测值和相位观测值中多路径效应的影响。此外,主要研究了利用相位平滑伪距削弱伪距多路径误差的方法和利用小波分析的方法对GPS多路径值序列进行分解和重构,提取出高精度的多路径误差,并通过实验数据分析了几种方法中的多路径效应影响。     

变形监测中GPS多路径效应的削弱方法研究

本文主要从GPS的基本观测方程出发,通过数学分析的方法,在GPS观测值之间建立数学模型,进一步推导了伪距观测值和相位观测值中多路径效应的影响.此外,主要研究了利用相位平滑伪距削弱伪距多路径误差的方法,以及利用小波分析的方法对GPS多路径值序列进行分解和重构,提取出高精度的多路径误差,并通过实验数据分析了几种方法中的多路径效应.     

BDS-3卫星伪距偏差及多路径误差分析

卫星伪距偏差对卫星精密定位的实现及其应用会产生较大的影响,为了探究BDS-3卫星伪距观测值是否存在伪距偏差,正确评价BDS-2和BDS-3各频率信号伪距观测值多路径误差,推导了可以度量多路径及噪声的无几何和无电离层的多路径组合(MP)观测量,并利用全球均匀分布的43个MGEX测站的观测数据,计算分析了多路径误差与卫星高度角的关系,对比分析了BDS-2和BDS-3不同频率信号伪距多路径的特性,统计了多路径误差的均方根,结果表明BDS-3伪距多路径误差明显小于BDS-2,验证了BDS-3卫星伪距观测值中不存在与卫星相关的伪距偏差。     

GNSS多路径和信噪比相关性分析

在全球导航卫星系统(Global Navigation Satellite System,GNSS)接收机附近的反射、衍射、干扰信号等所造成的多路径效应是影响定位的主要误差来源。信噪比(Signal-Noise Ratio,SNR)的振荡是由多路径信号叠加在直接信号上引起的,基于此原理学者们提出了很多检测和缓解多路径误差的方法。本文通过谱分析的方法对多路径时间序列进行了分析,并研究多路径与信噪比之间的相关性,对基于信噪比检测和缓解多路径误差的方法的适用性进行了说明。实验表明:多路径和信噪比振荡值的时间序列具有显著的相关性,能够利用信噪比观测值削弱多路径影响。     

BDS伪距多路径效应误差分析及修正

北斗星座包含3类卫星,即GEO、IGSO和MEO,GEO卫星高度角变化微小,伪距多路径观测序列系统偏差较明显;IGSO、MEO卫星随多路径序列系统偏差随卫星高度角变化,多路径误差对单个接收机定位结果影响较大.本文针对GEO卫星伪距观测值偏差问题提出了一种基于卡尔曼滤波的修正方法,利用3 d的多路径效应误差观测序列进行拟...     

基于高度角的多路径改正模型在BDS相对定位中的应用

伪距观测值的精度对相对定位解算的收敛速度有很大影响。相关研究发现BDS伪距观测值中存在与高度角相关的多路径偏差,严重降低了伪距观测值的精度。通过EMD滤波和多项式拟合建立基于高度角的多路径改正模型对这类误差进行消除。实验结果表明,基于高度角的多路径改正模型可以有效提高伪距观测值精度,加快相对定位结果收敛速度,改正后四个时段的2 h定位结果精度分别提高了64.1％、43.9％、35.3％、66.0％。      

一种计算北斗三频多路径的方法及其结果分析

多路径误差分析是北斗卫星导航系统性能评估的一项重要内容。本文给出了一种新的计算3频多路径误差的方法,该方法只需对B1和B2载波相位观测值进行处理就能得到3个频率的伪距多路径误差。利用MGEX跟踪站的数据计算了BDS的多路径误差,从GPS和BDS多路径误差比较以及纬度、轨道和频率因素分析了BDS多路径误差的特性,结果表明,BDS多路径误差小于0．5 m,符合质量检查要求,其性能优于GPS卫星系统。     

大型斜拉桥环境下BDS/GPS观测数据质量分析

为了进一步提高大型斜拉桥环境下BDS系统的监测精度,进一步对相关影响进行分析处理,以苏通大桥为试验对象,通过采集不同部位的站点BDS/GPS卫星观测数据,采用自编的BDS观测数据质量分析软件与TQEC软件对观测数据的完整性、观测值与周跳比、卫星信号信噪比及多路径误差等进行计算分析。结果表明,BDS卫星数据完整性优于GPS,但信噪比与多路径误差不及GPS稳定,同时桥面观测环境下的各项指标低于岸边观测环境。因此在采用BDS进行桥梁监测时,在误差处理与解算方法上必须考虑桥梁环境的影响,特别是对多路径的处理,以更有效分离变形。     

多路径误差对GPS C/A码伪距观测量影响的实验性研究

本文讨论了多路径误差对GPSC/A码伪距观测量的影响。通过在若干不同反射环境下进行实验性观测,本文分析和讨论了建筑物、高压线、地面、卫星自身以及水面反射引起的多路径误差的某些特征。其结论对研究GPS多路径误差的影响和实施GPS观测有一定的参考作用。     

利用信噪比削弱多路径误差的方法研究

多路径效应是卫星导航定位中重要的误差源,在分析多路径效应的产生原理以及多路径效应与信噪比相关性的基础上,提出了可利用信噪比削弱多路径效应的方法,并利用自测的GPS观测数据进行了验证。     

基于均衡复现的载波多径抑制技术

本文基于扩频信号分析了不同多径参数对载波幅度和相位的影响,在低信噪比条件下,使用自适应均衡技术,实时估计多径参数和抑制载波多径。使用实时估计得到的多径参数,重构多径信号,从接受信号中消去多径信号。仿真结果表明,这2种算法均能很好地降低多径对载波的影响,可以有效提高载波相位的测量精度。     

L2C码与L2载波数据质量分析

基于IGS的L2C信号跟踪站数据验证了具有L2C码的卫星的L2载波的信噪比高于没有L2C码的卫星的L2载波的信噪比,L2载波恢复的数据质量更好.针对不同的接收机,对比分析了C/A码和L2C码多路径效应及观测噪声水平,发现对TRIMBLE NETRS接收机,L2C码误差水平明显高于C/A码,与期望结果相反.     

GNSS multipath detection using three-frequency signal-to-noise measurements

A new technique for detecting GNSS multipath interference by comparing signal-to-noise (SNR) measurements on three frequencies is presented. Depending on the phase lag of the reflected signal with respect to the direct signal, multipath interference can be either constructive or destructive, with a commensurate effect on the measured SNR. However, as the phase lag is frequency dependent, the SNR is perturbed differently on each frequency. Thus, by differencing SNR measurements on different frequencies and comparing the result with that obtained in a low-multipath environment, multipath can be detected. Using three frequencies makes the process more robust. A three-frequency SNR-based multipath detector has been developed and calibrated using measurements from GPS Block IIF satellites in a low-multipath environment. The new detector has been tested in a range of urban environments and its multipath detection capability verified by showing that the MP observables oscillate when the new detection statistic is above a threshold value determined using data collected in a low-multipath environment. The new detector is also sensitive to diffraction.     

Variable length LMS adaptive filter for carrier phase multipath mitigation

Multipath on carrier phase measurements is among the major error sources for short baseline positioning. A new method is proposed to improve the accuracy of the positioning results by mitigating the multipath effects on carrier phase measurements using the variable length Least Mean Square (VLLMS) adaptive filter. The performance of the filter is analyzed as well as compared with that of the standard LMS adaptive filter using a set of carrier phase observation data of two consecutive days collected in a short baseline experiment. Because the two antennas are static, the multipath error is the only dominant component in the carrier phase double-differenced residuals and indicates a repeated pattern. The numerical results show that both filters can significantly mitigate the multipath effects in carrier phase double-differenced residuals, and hence improve the positioning results. Furthermore, the VLLMS filter that reduces up to about 47.4% of the multipath effects on 3D positioning performs better than the LMS filter that only reduces 22.0%. Both filters are suitable for real-time applications.     

GNSS信号多径误差非包络评估方法

针对全球导航卫星系统(global navigation satellite system, GNSS)信号体制评估过程中,多径误差包络评估方法给出了多径误差的上界,并没有反映反射信号载波和子载波相位引入的码跟踪误差问题,提出了一种码跟踪多径误差非包络评估方法。该方法将反射信号的码相位延时映射到载波和子载波相位延时,为码跟踪多径误差提供了准确的理论值,而且避免了多径误差包络方法求包络曲线的过程。给出了该方法的理论表达式,对BPSK、AltBOC、MBOC和BOC信号进行了多径性能仿真,并与多径误差包络评估方法进行了对比。理论和仿真结果表明,本文方法能准确的估计码跟踪多径误差,为GNSS信号多径误差测量值提供有效的理论指导。     

Wavelet packets based denoising method for measurement domain repeat-time multipath filtering in GPS static high-precision positioning

Repeatable satellite orbits can be used for multipath mitigation in GPS-based deformation monitoring and other high-precision GPS applications that involve continuous observation with static antennas. Multipath signals at a static station repeat when the GPS constellation repeats given the same site environment. Repeat-time multipath filtering techniques need noise reduction methods to remove the white noise in carrier phase measurement residuals in order to retrieve the carrier phase multipath corrections for the next day. We propose a generic and robust three-level wavelet packets based denoising method for repeat-time-based carrier phase multipath filtering in relative positioning; the method does not need tuning to work with different data sets. The proposed denoising method is tested rigorously and compared with two other denoising methods. Three rooftop data sets collected at the University of Nottingham Ningbo China and two data sets collected at three Southern California Integrated GPS Network high-rate stations are used in the performance assessment. Test results of the wavelet packets denoising method are compared with the results of the resistor–capacitor (RC) low-pass filter and the single-level discrete wavelet transform (DWT) denoising method. Multipath mitigation efficiency in carrier phase measurement domain is shown by spectrum analysis of two selected satellites in two data sets. The positioning performance of the repeat-time-based multipath filtering techniques is assessed. The results show that the performance of the three noise reduction techniques is about 1–46 % improvement on positioning accuracy when compared with no multipath filtering. The statistical results show that the wavelet packets based denoising method is always better than the RC filter by 2–4 %, and better than the DWT method by 6–15 %. These results suggest that the proposed wavelet packets based denoising method is better than both the DWT method and the relatively simple RC low-pass filter for noise reduction in multipath filtering. However, the wavelet packets based denoising method is not significantly better than the RC filter.     

GPS现代化后L_2载波的定位精度研究

利用实际采集的数据,从信噪比和定位残差上分析了L2载波的数据质量,指出GPS现代化后,用L2C码恢复的L2载波信噪比明显提高,与L1载波信噪比接近,两者的差值仅在5 dBHz以内;用L2C码恢复的L2载波比GPS现代化前的L2载波的信噪比更加稳定,不容易受卫星高度角的影响;同时利用L2C码恢复的L2载波的定位残差比没有L2C码的L2载波小,定位精度明显提高。     

A comparison of P code and high performance C/A code GPS receivers for on the fly ambiguity resolution

Carrier phase ambiguity resolution on the fly is investigated using two receiver technologies, namely dual-frequency P code and high performance, single frequency, C/A code receivers. Both receiver types were used simultaneously in a series of land kinematic trials. A least-squares search technique is used to find the correct double difference carrier phase ambiguities. Both C/A and single frequency P code technologies are found to be equivalent and capable of resolving the integer ambiguities on the fly using some 30 to 200 seconds of data under benign multipath conditions. Successful ambiguity resolution on the fly results in cm-level accuracy kinematic positioning. The ambiguity resolution time required and success rate are however found to be strongly dependent on the level of carrier phase multipath and, as a consequence, on the error variance assigned to the carrier phase measurements. The use of widelaning with the dual frequency P code results in ambiguity resolution in seconds. The performance of widelaning is also superior in a comparatively high carrier phase multipath environment.     

北斗二代观测值质量分析及随机模型精化

对北斗观测值进行了质量分析,包括观测值的信噪比、多路径和解算的单差残差时间序列随高度角的变化情况。北斗载波相位单差残差随高度角的统计可为高度角加权和信噪比加权进行模型精化,从而获得适合北斗卫星载波观测的随机模型。实验分析表明,北斗系统的观测值质量要稍优于GPS观测值质量,尤其是在卫星高度角较小时表现明显。同时北斗观测值的残差分析为北斗定位中随机模型的建立提供依据。