Solutions for Non‐Darcian Flow to an Extended Well in Fractured Rock

We have investigated non‐Darcian flow to a vertical fracture represented as an extended well using a linearization procedure and a finite difference method in this study. Approximate analytical solutions have been obtained with and without the consideration of fracture storage based on the linearization procedure. A numerical solution for such a non‐Darcian flow case has also been obtained with a finite difference method. We have compared the numerical solution with the approximate analytical solutions obtained by the linearization method and the Boltzmann transform. The results indicate that the linearized solution agrees generally well with the numerical solution at late times, and underestimates the dimensionless drawdown at early times, no matter if the fracture storage is considered or not. When the fracture storage is excluded, the Boltzmann transform solution overestimates the dimensionless drawdown during the entire pumping period. The dimensionless drawdowns in the fracture with fracture storage for different values of dimensionless non‐Darcian hydraulic conductivity β approach the same asymptotic value at early times. A larger β value results in a smaller dimensionless drawdown in both the fracture and the aquifer when the fracture storage is included. The dimensionless drawdown is approximately proportional to the square root of the dimensionless time at late times.     

On‐Site Vapor‐Phase Analysis as a Novel Approach for Monitoring Groundwater Wells

The results of comprehensive field testing of on‐site vapor‐phase‐based groundwater monitoring methods are presented to demonstrate their utility as a robust and cost‐effective approach for rapidly obtaining volatile organic compounds (VOCs) concentration data from a monitoring well. These methods—which rely on sensitive, commercially available field equipment to analyze vapor in equilibrium with groundwater—proved easy to implement and can be tailored to site‐specific needs, including multilevel sampling. During field testing, low‐flow groundwater concentrations could be reasonably estimated using submerged passive vapor diffusion samplers or field equilibration of collected groundwater (R² = 0.85 to 0.96). These two methods are not as reliant on in‐well mixing to overcome vertical stratification within wells as simpler headspace methods. The importance of well and aquifer‐specific factors on concentration data (and therefore method selection) is highlighted, including the effect of changing in‐well patterns due to seasonal temperature gradients. Results indicated that vertical stratification was relatively limited within the set of wells included in these studies, resulting in similar performance for short depth‐discrete passive vapor diffusion samplers (constructed from 40‐mL vials) and longer samplers (2.5 to 5 feet in length) designed to cover a larger portion of the screened interval. A year‐long, multi‐event evaluation demonstrated that vapor‐phase‐based monitoring methods are no more variable than conventional groundwater monitoring methods, with both types subject to similar spatial and temporal variability that can be difficult to reduce. Vapor sampling methods represent a promising approach for estimation of groundwater concentrations by reducing the cost liabilities associated with monitoring while providing a more sustainable approach.     

Design of a Low-Cost Bamboo Well

Bamboo wells are an economical alternative for water supply wells in developing countries. The design of the bamboo well described in this article was developed based on field tests. Following field experiments, the screen in the bamboo well was fabricated with seven 3-m-long bamboo strips, each 2 cm wide and 1 cm thick. The strips were bolted on 1-cm-wide mild steel rings spaced 30 cm along the length of the bamboo strips, with 9-cm-long galvanized iron pipe end pieces. Pipes used in the bamboo well were fabricated by wrapping polythene sheets on the bamboo screens. Excellent performance, low cost, and good service life justify the use of a bamboo well for ground water withdrawal in developing countries.     

Modeling Arsenic Sorption in the Subsurface with a Dual‐Site Model

Arsenic is a well‐known groundwater contaminant that causes toxicological and carcinogenic effects in humans. Predicting the transport of arsenic in the subsurface is often problematic because of its complex sorption characteristics. Numerous researchers have reported that arsenic sorption on soil material is initially fast and then subsequently slow. A dual‐site numerical sorption model was previously developed to describe arsenic desorption from arsenic‐contaminated soils in batch experiments in terms of two different release mechanisms. Experiments involving synthetic acid rain leaching of four arsenic‐contaminated soil columns were performed to verify the dual‐site numerical sorption model in the context of one‐dimensional vertical transport. The fitted models successfully simulated the signature long tailings and the two‐stage arsenic leaching patterns for all four soil columns. The dual‐site sorption model was incorporated within the general solute transport simulation code Modular Three‐Dimensional Multispecies (MT3DMS), version 5.10. The resulting version was named MT3DDS and is available for public access. This experimental study has shown that MT3DDS is capable of simulating phase redistribution during transport, and thus provides a new numerical tool for simulating arsenic transport in the subsurface.     

Design of a Multi-Level Monitoring Well for Continuous Sample Collection

As part of a study of the flow dynamics and sampling environment around a high-capacity irrigation well, it was necessary to design and install a multi-level monitoring well network close to the production well. A requirement of the monitoring well network was the capability of continuous pumping over periods typical of those used during water sample collection. This was accomplished through the use of a control valve and air manifold system connected 10 a common gasoline engine-operated air compressor. The system provided adequate air pressure to operate 24 half-size bladder pumps to depths between 21 feet (6.4 m) and 56 feet (17.1 m) below the surface. Preliminary data collected from the monitoring well network indicate that the system will meet the requirements of the high-capacity well study.     

Process Performance of a Biotrickling Filter Using a Flow‐Directional‐Switching Method

Non‐uniform distribution of biomass and the accumulation of excess biomass at the inlet of a unidirectional flow biotrickling filter (UF‐BTF) may lead to severe operating problems including increasing airflow resistance in packed bed, clogging, and low contaminant removal efficiencies, even performance loss. Therefore, a flow‐directional‐switching biotrickling filter (FDS‐BTF) was designed to improve performance such as the maximum elimination capacity and elimination efficiency. Toluene was chosen as the unique carbon source for microorganism. The results indicated that the purification performance of FDS‐BTF was superior to UF‐BTF. The maximum elimination capacity of FDS‐BTF was up to 480 g/(m³ h), which was 17.1% higher than that of UF‐BTF. After a 50‐day continuous operation, FDS‐BTF attained the stable purification performance and the outlet concentrations of toluene could meet the emission standard with inlet concentrations ranging from 720 to 1100 mg/m³ for an empty bed residence time (EBRT) of 23.9 s. The average well color development in FDS‐BTF was higher than that in UF‐BTF. It indicated that FDS‐BTF could improve the metabolic activity, which may improve the uniform distribution of biomass along the length of packed bed. When two systems were shut down, 24 and 48 h, respectively, the time that FDS‐BTF and UF‐BTF needed to restore the former elimination efficiency after a shut down of 48 h were 3–4 and 9–10 h. These data indicated that the purification performance of FDS‐BTF was superior to UF‐BTF.     

Analytical Solution for Well Design with Respect to Discharge Ratio

For a well in the vicinity of a surface water body, a formula is developed that relates the share of bank filtrate on total pumpage, that is, the discharge ratio, on one side, to basic well and aquifer characteristics on the other. The application of the formula is demonstrated for solving the inverse problem: for an aimed discharge ratio, well characteristics (pumping rate, distance to shore) can be determined. Other useful applications of the formula are outlined.     

Estimation of Salt Water Upconing Using a Steady‐State Solution for Partial Completion of a Pumped Well

A new steady‐state analytical solution to the two‐dimensional radial‐flow equation was developed for drawdown (head) conditions in an aquifer with constant transmissivity, no‐flow conditions at the top and bottom, constant head conditions at a known radial distance, and a partially completed pumping well. The solution was evaluated for accuracy by comparison to numerical simulations using MODFLOW. The solution was then used to estimate the rise of the salt water‐fresh water interface (upconing) that occurs under a pumping well, and to calculate the critical pumping rate at which the interface becomes unstable, allowing salt water to enter the pumping well. The analysis of salt water‐fresh water interface rise assumed no significant effect on upconing by recharge; this assumption was tested and supported using results from a new steady‐state analytical solution developed for recharge under two‐dimensional radial‐flow conditions. The upconing analysis results were evaluated for accuracy by comparison to those from numerical simulations using SEAWAT for salt water‐fresh water interface positions under mild pumping conditions. The results from the equation were also compared with those of a published numerical sharp‐interface model applied to a case on Cape Cod, Massachusetts. This comparison indicates that estimating the interface rise and maximum allowable pumping rate using the analytical method will likely be less conservative than the maximum allowable pumping rate and maximum stable interface rise from a numerical sharp‐interface model.     

On Methods for In‐Well Nitrate Monitoring Using Optical Sensors

Optical sensors are promising for collecting high resolution in‐well groundwater nitrate monitoring data. Traditional well purging methods are labor intensive, can disturb ambient conditions and yield an unknown blend of groundwater in the samples collected, and obtain samples at a limited temporal resolution (i.e., monthly or seasonally). This study evaluated the Submersible Ultraviolet Nitrate Analyzer (SUNA) for in‐well nitrate monitoring through new applications in shallow overburden and fractured bedrock environments. Results indicated that SUNA nitrate‐N concentration measurements during flow cell testing were strongly correlated (R ² = 0.99) to purged sample concentrations. Vertical profiling of the water column identified distinct zones having different nitrate‐N concentrations in conventional long‐screened overburden wells and open bedrock boreholes. Real‐time remote monitoring revealed dynamic responses in nitrate‐N concentrations following recharge events. The monitoring platform significantly reduced labor requirements for the large amount of data produced. Practitioners should consider using optical sensors for real‐time monitoring if nitrate concentrations are expected to change rapidly, or if a site's physical constraints make traditional sampling programs challenging. This study demonstrates the feasibility of applying the SUNA in shallow overburden and fractured bedrock environments to obtain reliable data, identifies operational challenges encountered, and discusses the range of insights available to groundwater professionals so they will seek to gather high resolution in‐well monitoring data wherever possible.     

Novel coupling Rosenbrock‐based algorithms for real‐time dynamic substructure testing

Real‐time testing with dynamic substructuring is a novel experimental technique capable of assessing the behaviour of structures subjected to dynamic loadings including earthquakes. The technique involves recreating the dynamics of the entire structure by combining an experimental test piece consisting of part of the structure with a numerical model simulating the remainder of the structure. These substructures interact in real time to emulate the behaviour of the entire structure. Time integration is the most versatile method for analysing the general case of linear and non‐linear semi‐discretized equations of motion. In this paper we propose for substructure testing, L‐stable real‐time (LSRT) compatible integrators with two and three stages derived from the Rosenbrock methods. These algorithms are unconditionally stable for uncoupled problems and entail a moderate computational cost for real‐time performance. They can also effectively deal with stiff problems, i.e. complex emulated structures for which solutions can change on a time scale that is very short compared with the interval of time integration, but where the solution of interest changes on a much longer time scale. Stability conditions of the coupled substructures are analysed by means of the zero‐stability approach, and the accuracy of the novel algorithms in the coupled case is assessed in both the unforced and forced conditions. LSRT algorithms are shown to be more competitive than popular Runge–Kutta methods in terms of stability, accuracy and ease of implementation. Numerical simulations and real‐time substructure tests are used to demonstrate the favourable properties of the proposed algorithms. Copyright © 2007 John Wiley & Sons, Ltd.     

Arsenic Remediation Field Study Using a Sulfate Reduction and Zero‐Valent Iron PRB

Toxic and carcinogenic effects of arsenic in drinking water continue to impact people throughout the world and arsenic remains common in groundwater at cleanup sites and in areas with natural sources. Advances in groundwater remediation are needed to attain the low concentrations that are protective of human health and the environment. In this article, we present the successful use of a permeable reactive barrier (PRB) utilizing sulfate reduction coupled with zero‐valent iron (ZVI) to remediate the leading edge of a dissolved arsenic plume in a wetland area near Tacoma, Washington. A commercially available product (EHC‐M®, Adventus Americas Inc., Freeport, Illinois) that contains ZVI, organic carbon substrate, and sulfate was injected into a reducing, low‐seepage‐velocity aquifer elevated in dissolved arsenic and iron from a nearby, slag‐containing landfill. Removal effectiveness was strongly correlated with sulfate concentration, and was coincident with temporary redox potential (Eh) reductions, consistent with arsenic removal by iron sulfide precipitation. The PRB demonstrates that induced sulfate reduction and ZVI are capable of attaining a regulatory limit of 5 µg/L total arsenic, capturing of 97% of the arsenic entering the PRB, and sustaining decreased arsenic concentrations for approximately 2 years, suggesting that the technology is appropriate for consideration at other sites with similar hydrogeochemical conditions. The results indicate the importance of delivery and longevity of minimum sulfate concentrations and of maintaining sufficient dissolved organic carbon and/or microscale ZVI to precipitate FeS, a precursor phase to arsenic‐bearing pyrite that may provide a stable, long‐term sink for arsenic.