土工格栅加筋砂土中水平锚板抗拔特性试验研究

土工格栅加筋能够有效改善锚板的抗拔承载力,然而锚板在上拔过程中的破坏机制及其影响因素尚需进一步研究。针对砂土中水平锚板的抗拔特性,开展了多组锚板上拔试验,分析了砂土密实度、锚板埋深、土工格栅布设层数和位置等因素的影响,结合粒子图像测速（particle image velocimetry,简称PIV）技术探究了锚板周边土体的变形破坏机制。研究结果表明：单层接触式格栅加筋对锚板的抗拔承载力有明显的提升,且其对土体性能的改善优于非接触式格栅加筋情况,其原因与土工格栅变形量和上覆土体重力有关;当采用双层土工格栅加筋时,下层格栅可充分发挥限制土体侧向变形和均化应力分布的作用,上层格栅相对而言贡献不大;采用土工格栅加筋后,锚-土界面附近土体的变形模式发生了明显的变化,其破坏面相比未加筋前向内侧收敛,且剪应变分布更为均匀。     

Three-dimensional analysis of vertical square anchor plate in cohesionless soil

ABSTRACT

Vertical anchor plates are often provided to increase the performance of various geotechnical engineering structures such as sheet pile walls, bulkheads, bridge abutments and offshore structures. Hence, the safe design of such structures needs a better understanding of the 3D behaviour of the anchor plate. This paper presents and discusses the results obtained from a series of 3D finite-difference analyses of vertical square anchor plate embedded in cohesionless soil. The 3D model is found to closely predict experimental pullout load–displacement relationship. The failure mechanism observed in the numerical model is found to be very similar to the failure reported in experimental studies. For a given embedment depth, the stiffness of the breakout factor–displacement response substantially reduces with increase in anchor plate size. However, the ultimate reduction in anchor capacity is found to approximately 8% with an increase in anchor size from 0.1 to 1 m. Numerical analysis reveals that at deeper embedment depth, the friction angle of sand is the critical parameter in enhancing the performance of anchor plate. The obtained 3D model results are then compared with the published results and are found to be reasonably in good agreement with each other.     

水平荷载作用下群桩相互作用的弹塑性数值分析

本文利用三维弹塑性有限元法对水平荷载作用下群桩基础特性进行了分析,讨论了群桩基础水平荷载作用下的承载性状和破坏机理,并探讨了桩距、桩数、桩长、桩径和土质各种因素对群桩效应的影响,指出桩距和桩数是影响群桩效应的主要因素.     

粉细砂层中锚索施工涌水涌砂的处理技术

广州市良业大厦基坑支护工程存在较厚的淤泥质粉细砂层,预应力锚索锚点位置处于粉细砂层中时,锚索施工易发生涌水涌砂现象而引发基坑事故。施工过程中通过采取跟管钻进干钻成孔、墙后孔口设置止浆袋及墙后注浆的处理措施,减少了锚索施工过程中涌水涌砂现象的发生,避免了因涌水涌砂水土流失造成基坑外地面下沉而引发的基坑事故。     

Pullout capacity of multi-plate horizontal anchors in sand: an experimental study

Acta Geotechnica - A horizontal anchor is a structural member designed to resist the vertical pullout forces and ensure the stability of structures like the tower foundations, masts and bridges....     

砂土中群锚锚周土体变形特性模型试验研究

群锚是常见的基础形式应用较为广泛,由于群锚之间的相互作用,群锚上拔过程中锚周土体的变形破坏机制比较复杂。采用非接触式数字图像相关方法（DIC）对群锚上拔过程开展模型试验研究,分析了群锚上拔过程中上拔力-位移关系曲线特征和锚周土体变形破坏机制。试验结果表明,密实度和埋深对群锚上拔力-位移关系曲线特征具有显著影响,在相同密实度、相同埋深率下浅埋与深埋群锚与同条件下的单锚具有相似的上拔力-位移关系曲线特征;群锚抗拔承载力具有明显的叠加效应,且砂土密实度、埋深和锚间距等参数因素对群锚效应具有显著影响。通过变形场的研究,得出了砂土密实度、埋深以及锚间距对群锚效应的影响规律。     

Field and numerical study of the lateral response of rigid piles in sand

Acta Geotechnica - Large diameter, short monopiles are the preferred foundation type for offshore wind turbines. These piles demonstrate a rigid response with significant rotation of the pile base...     

砂土中群桩的压拔加载试验研究

进行砂土的单桩和2×2群桩的压、拔试验,测定桩身轴力、桩顶荷载、位移以及桩端阻力。试验研究结果表明,群桩的抗压群桩效应系数 >1,最优桩间距为4D(D为直径),对应的 约为1.2;桩端阻力群桩效应系数 大于桩侧摩阻力群桩效应系数 ,其最优桩间距为5D,对应的 值约为1.3;桩侧摩阻力群桩效应系数在3D时约为1.2,但随桩间距的增大而减小。与前人理论分析的结果不同,由于砂土的挤密效应,试验测得抗拔群桩效应系数也大于1,最优桩间距在4D～5D之间,系数约为1.2。桩间距为7D时压、拔群桩效应系数均趋近于1,可基本忽略群桩效应。     

An analytical study on groundwater flow in drainage basins with horizontal wells

Analytical studies on release/capture zones are often limited to a uniform background groundwater flow. In fact, for basin-scale problems, the undulating water table would lead to the development of hierarchically nested flow systems, which are more complex than a uniform flow. Under the premise that the water table is a replica of undulating topography and hardly influenced by wells, an analytical solution of hydraulic head is derived for a two-dimensional cross section of a drainage basin with horizontal injection/pumping wells. Based on the analytical solution, distributions of hydraulic head, stagnation points and flow systems (including release/capture zones) are explored. The superposition of injection/pumping wells onto the background flow field leads to the development of new internal stagnation points and new flow systems (including release/capture zones). Generally speaking, the existence of n injection/pumping wells would result in up to n new internal stagnation points and up to 2n new flow systems (including release/capture zones). The analytical study presented, which integrates traditional well hydraulics with the theory of regional groundwater flow, is useful in understanding basin-scale groundwater flow influenced by human activities.     

Response of circular footings and anchor plates in non-homogeneous elastic soils

The axisymmetric elastic response of circular footings and anchor plates in a linearly non-homogeneous elastic soil is analysed. It is assumed that footings/anchors are flexible and subjected to axisymmetric vertical loads. The response of the footing/anchor is modelled by using the classical Poisson–Kirchhoff thin plate theory. A variational technique is used to analyse the interaction problem. A representation for the contact stress is established by using a fundamental solution corresponding to a unit vertical pressure acting over an annular region in the interior of the non-homogeneous soil. The fundamental solution can be derived by using rigorous analytical procedures. The influence of the footing flexibility and the degree of soil non-homogeneity on the displacements, bending moments and contact stresses of a surface footing is examined over a wide range of governing parameters. In the case of anchor plates the influence of depth of embedment, degree of soil non-homogeneity and anchor flexibility on the anchor displacement is investigated.     

Uplift response of symmetrical anchor plates in reinforced cohesionless soil

The uplift response of symmetrical anchor plates with and without geogrid reinforcement layers has been evaluated in model tests and numerical simulations using PLAXIS. Many parameters of the reinforcement layers were used to reinforce the sandy soil over circular, square, and rectangular symmetrical anchor plates of various sizes. In the current research, different parameters, such as relative density of sand and embedment ratios, in conjunction with geogrid reinforcement layer parameters including size, number of layers, and the proximity of the layer to the circular anchor plate, were investigated in a scale model. The failure mechanism and the associated rupture surface were observed and evaluated. Test results showed that using geogrid reinforcement layers significantly improves the uplift capacity of symmetrical anchor plates. It was found that inclusion of one geogrid layer resting directly on top of the symmetrical anchor plate was more effective in enhancing the symmetrical anchor capacity than the layer itself. It was also found that the inclusion of one geogrid layer on the symmetrical anchor plate improved the uplift capacity more than the same symmetrical anchor plate embedded without a reinforcement layer. The single geogrid layer was also more effective in enhancing the uplift capacity compared to the multiple geogrid layer reinforcement approach. In general, the results show that the uplift capacity of symmetrical anchor plates in loose and dense sand can be significantly increased by the inclusion of geogrid layers. It was also observed that the inclusion of geogrid layers reduces the requirement for a higher L/D ratio to achieve the required uplift capacity. The results of the laboratory and numerical analysis are found to be in agreement in terms of the breakout factor and failure mechanism pattern.     

不同支护条件下锚杆支护作用的模型试验研究与数值分析

以重庆至长沙公路共和隧道为研究对象,研制出相似模型材料和配套试验设备,进行不同长度锚杆支护条件下的隧道超载试验。采用应变测量技术,测量两种不同长度锚杆支护工况下的隧道关键部位的应变值,据此分析围岩体在锚杆支护后的应力变化规律。通过模型材料室内试验,获取岩体相关计算参数,采用与模型试验相同的边界条件进行相应工况的有限元数值模拟,研究围岩体的变形量、应力场和锚杆轴力因锚杆长度不同而产生的变化。结果表明,模型试验和数值模拟反映围岩体应力和锚杆轴力因锚杆长度的不同而产生的变化是一致的。     

饱和粉细砂层锚索预应力变化规律监测分析

锚索的预应力损失在工程建设中不可忽视,工程的场地环境条件成为影响锚索预应力损失的主因。饱和粉细砂层较其他地质条件更为复杂敏感,更易引起锚索预应力值的损失。通过对廊坊市某深基坑工程锚索预应力值的实时监测,结合工程环境,分析饱和粉细砂层中造成锚索预应力值变化的原因。结果表明,施工过程、张拉过程以及环境因素都影响锚索预应力的变化,其中开挖过程的影响最明显,预应力值的变化率最大值达79.1%;瞬时卸载造成预应力值22.8%⁵9.2%的损失。对饱和粉细砂层中锚索预应力变化规律的研究分析结论可为类似地质环境的工程建设提供经验。     

砂土的渐进破坏及其数值模拟

紧密砂土在排水剪切过程中由于材料的应变软化特性,会出现变形局部化并伴随剪切带的产生。对此类问题进行数值模拟时会遇到很多困难,比如如何模拟紧砂的应变软化特性,如何处理有限元数值分析过程中刚度矩阵的非正定导致计算结果发散问题,以及如何处理应力不连续的问题,拟针对以上问题进行了探讨。     

新型伞状抗拔锚现场试验与数值模拟

伞状抗拔锚是一种新型的锚杆装置。通过现场试验获得了其抗拔承载性能,从正常使用条件下Q-S曲线可见,与同场地施工的抗拔桩比较,新型伞状抗拔锚的承载力显著提高。鉴于试验条件的不足,未能获得伞状抗拔锚的极限承载力。为获得伞状锚达到极限状态时的Q-S曲线,采用ABAQUS有限元软件,对伞状抗拔锚和抗拔桩的原位抗拔试验进行数值模拟。模拟主要分2步来实现,先通过调节参数得到与试验一致的正常使用条件下的Q-S曲线,然后增加荷载,得到极限状态下的伞状抗拔锚的Q-S曲线。结果显示,伞状抗拔锚能够充分调动其扩大端的土体参与抗拔,得到的Q-S曲线表明伞状锚的抗拔性能存在很大潜力,具有显著的优越性。     

内孤立波环境下圆柱和方柱受力特征——II.数值模拟

柱体受内波作用力的数值模拟大多针对圆柱展开,方柱在内波环境下受力特性研究较少。借助三维数值波浪水槽,采用大涡模拟（LES）技术研究了内孤立波的产生、传播及其对不同形状柱体的受力特性。对比分析了内孤立波波幅对圆柱和方柱受力的影响规律。研究表明,在分层流环境下,随着内孤立波波幅的增大,圆柱和方柱所受的水平作用力均增大;相同波幅情况下,无论在上层或下层水体,方柱表面的压力分布更不均匀,迎流面与背流面的压差更大,从而导致方柱相较于圆柱会受到更大的水平作用力。     

岩石倾斜裂隙与水平裂隙扩展贯通试验及数值模拟研究

采用最新配置的水泥砂浆材料,通过在试件中布置倾斜裂隙和水平裂隙,开展了单轴和双轴条件下的压缩试验,详细分析了不同加载条件下试件裂隙的扩展和贯通规律。试验结果表明:无裂隙内水压时,在单轴压缩条件下倾斜裂隙在扩展贯通水平裂隙后裂纹的扩展路径和方向发生明显改变,试样最终发生劈裂破坏。侧压的增大抑制了倾斜裂隙端部翼裂纹和次生裂纹的萌生,高侧压下翼裂纹没有贯穿水平裂隙,试样破坏模式变成了剪切破坏。水力耦合作用下,单轴压缩时倾斜裂隙翼裂纹尖端的最大主应力分布范围随着内水压的增大逐渐变小,翼裂纹的起裂应力、起裂角和峰值强度逐渐降低,试样发生劈裂破坏。通过数值模拟得到的裂纹扩展贯通规律与试验结果具有良好的一致性,开展了不同内水压时倾斜裂隙扩展贯通无水压的水平裂隙的数值分析,随着内水压的增加倾斜裂隙首先萌生共面裂纹随后产生翼裂纹,翼裂纹扩展贯通水平裂隙时扩展路径同样会发生改变。水力耦合作用下侧压也会抑制翼裂纹的萌生,随着内水压的增大减弱了侧压对倾斜裂隙翼裂纹的抑制作用。     

Experimental,numerical and analytical study on conventional and innovative Grid-Anchor system in the pull-out test

With increasing use of geosynthetic applications in earth structures the need to develop more efficient reinforcement elements becomes evident. In this paper a conventional and an innovative geogrid system (named Grid-Anchor) are tested. The Grid-Anchor system consists of a conventional geogrid with anchors attached to it. The pull-out test has been used to highlight the capabilities of the product. Experimental investigation along with numerical studies using a finite element computer code was carried out. It was found that the ultimate pull-out resistance of a Grid-Anchor is more than that for an ordinary geogrid. Analytical study has been performed and the effect of an anchor group on the ultimate resistance of a geogrid was investigated.